Kuba Pawlak [Fri, 28 Aug 2015 12:05:22 +0000 (13:05 +0100)]
Bluetooth: Fix SCO link type handling on connection complete
Synchronous connections are initially created with type eSCO.
Link manager may reject proposed link parameters, which triggers
connection setup retry with a different set. Link type embedded
in responses should be disregarded until Synchronous Connect Complete
returns Success (0x00). Current code updates link type every time
which creates an issue when link type changes to SCO and back to eSCO
on further attepts.
Issue happens with BlackBerry 9100 and 9700 with Intel WilkinsPeak
on third connection setup attept
Loic Poulain [Thu, 27 Aug 2015 05:21:51 +0000 (07:21 +0200)]
Bluetooth: hci_intel: Add support for platform driver
A platform device can be used to provide some specific resources in
order to manage the controller. In this first patch we retrieve the
reset gpio which is used to power on/off the controller.
The main issue is to match the current tty with the correct pdev.
In case of ACPI, we can easily find the right tty/pdev pair because
they are both child of the same UART port.
If controller is powered-on from the driver, we need to wait for a
HCI boot event before being able to send any command.
Loic Poulain [Tue, 25 Aug 2015 15:55:44 +0000 (17:55 +0200)]
Bluetooth: hci_intel: Add Intel baudrate configuration support
Implement the set_baudrate callback for hci_intel.
- Controller requires a read Intel version command before updating
its baudrate.
- The operation consists in an async cmd since the controller does
not respond at the same speed.
- Wait 100ms to let the controller change its baudrate.
- Clear RTS until we change our own UART speed
Manage speed change in the setup function, we need to restore the oper
speed once chip has booted on patched firmware.
Stefan Schmidt [Thu, 20 Aug 2015 10:09:47 +0000 (12:09 +0200)]
nl802154: stricter input checking for boolean inputs
So far we handled boolean input by forcing them with !! and assigning
them into a bool. This allowed userspace to send values > 1 which were
used as 1. We should be stricter here and return -EINVAL for all but
0 or 1.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Nicholas Krause [Wed, 19 Aug 2015 01:23:01 +0000 (21:23 -0400)]
Bluetooth: Make the function sco_conn_del have a return type of void
This makes the function sco_conn_del have a return type of void now
due to this function always running successfully and thus never
needing to signal its caller when a non recoverable internal failure
occurs by returning a error code to its respective caller.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Achiad Shochat [Sun, 16 Aug 2015 13:04:50 +0000 (16:04 +0300)]
net/mlx5e: Ethtool link speed setting fixes
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Achiad Shochat [Sun, 16 Aug 2015 13:04:49 +0000 (16:04 +0300)]
net/mlx5e: HW LRO changes/fixes
- Change the maximum LRO session size from 16KB to 64KB
- Reduce the LRO session timeout from 512us to 32us in
order to reduce the TCP latency of non-LRO'ed flows.
- Fix skb_shinfo(skb)->gso_size and set skb_shinfo(skb)->gso_type.
- Fix a bug accessing un-initialized mdev pointer.
Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Achiad Shochat [Sun, 16 Aug 2015 13:04:46 +0000 (16:04 +0300)]
net/mlx5e: Make RSS indirection table size a constant
The indirection table size was defined by a variable that
was actually assigned a constant value.
Since we do not have any forseen intension to make it configurable
we simply made it a constant.
We also limit the number of channels such that the RSS indirection
table could always populate all RX rings.
Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's what's likely the last bluetooth-next pull request for 4.3:
- 6lowpan/802.15.4 refactoring, cleanups & fixes
- Document 6lowpan netdev usage in Documentation/networking/6lowpan.txt
- Support for UART based QCA Bluetooth controllers
- Power management support for Broeadcom Bluetooth controllers
- Change LE connection initiation to always use passive scanning first
- Support for new Silicon Wave USB ID
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Aug 2015 22:25:30 +0000 (15:25 -0700)]
Merge branch 'enic-devcmd2'
Govindarajulu Varadarajan says:
====================
enic: add devcmd2
This series adds new devcmd2 support. The first two patches are code
refactoring.
devcmd is an interface for driver to communicate with fw/adaptor. It
involves writing data to hardware registers and waiting for the result.
This mechanism does not scale well. The queuing of "no wait" devcmds is
done in firmware memory rather than on the host. Firmware memory is a
rather more scarce and valuable resource than host memory. A devcmd storm
from one vf can disrupt the service on other pf/vf. The lack of flow
control allows for possible denial of server from one VM to another.
Devcmd2 uses work queue to post the devcmds, just like tx work queue. This
allows better flow control.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
devcmd is an interface for driver to communicate with fw/adaptor. It
involves writing data to hardware registers and waiting for the result.
This mechanism does not scale well. The queuing of "no wait" devcmds is
done in firmware memory rather than on the host. Firmware memory is a
rather more scarce and valuable resource than host memory. A devcmd storm
from one vf can disrupt the service on other pf/vf. The lack of flow
control allows for possible denial of server from one VM to another.
Devcmd2 uses work queue to post the devcmds, just like tx work queue. This
allows better flow control.
Initialize devcmd2, if fails we fall back to devcmd1.
Also change the driver version.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com> Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add devcmd resources to vnic_res_type. Add data types used by devcmd.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com> Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: use netdev_<foo> or dev_<foo> instead of pr_<foo>
pr_info does not give any details about the interface involved. This patch
uses netdev_info for printing the message. Use dev_info where netdev is not
ready.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the structure definitions are in .c file to make them private to
that file. This patch moves the struct definition to .h file, So that their
definitions are accessible from other files.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Fri, 14 Aug 2015 22:37:15 +0000 (00:37 +0200)]
rhashtable-test: extend to test concurrency
After having tested insertion, lookup, table walk and removal, spawn a
number of threads running operations on the same rhashtable. Each of
them will:
1) insert it's own set of objects,
2) lookup every successfully inserted object and finally
3) remove objects in several rounds until all of them have been removed,
making sure the remaining ones are still found after each round.
This should put a good amount of load onto the system and due to
synchronising thread startup via two semaphores also extensive
concurrent table access.
The default number of ten threads returned within half a second on my
local VM with two cores. Running 200 threads took about four seconds. If
slow systems suffer too much from this though, the default could be
lowered or even set to zero so this extended test does not run at all by
default.
Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Aug 2015 21:31:42 +0000 (14:31 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- avoid integer overflow in GW selection routine
- prevent race condition by making capability bit changes atomic (use
clear/set/test_bit)
- fix synchronization issue in mcast tvlv handler
- fix crash on double list removal of TT Request objects
- fix leak by puring packets enqueued for sending upon iface removal
- ensure network header pointer is set in skb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Aug 2015 21:25:04 +0000 (14:25 -0700)]
Merge tag 'mac80211-next-for-davem-2015-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Aug 2015 21:22:48 +0000 (14:22 -0700)]
Merge branch 'bpf_fanout'
Willem de Bruijn says:
====================
packet: add cBPF and eBPF fanout modes
Allow programmable fanout modes. Support both classical BPF programs
passed directly and extended BPF programs passed by file descriptor.
One use case is packet steering by deep packet inspection, for
instance for packet steering by application layer header fields.
Separate the configuration of the fanout mode and the configuration
of the program, to allow dynamic updates to the latter at runtime.
Changes
v1 -> v2:
- follow SO_LOCK_FILTER semantics on filter updates
- only accept eBPF programs of type BPF_PROG_TYPE_SOCKET_FILTER
- rename PACKET_FANOUT_BPF to PACKET_FANOUT_CBPF to match
man 2 bpf usage: "classic" vs. "extended" BPF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 15 Aug 2015 02:31:37 +0000 (22:31 -0400)]
selftests/net: test extended BPF fanout mode
Test PACKET_FANOUT_EBPF by inserting a program into the the kernel
with bpf(), then attaching it to the fanout group. Observe the same
payload-based distribution as in the PACKET_FANOUT_CBPF test.
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 15 Aug 2015 02:31:36 +0000 (22:31 -0400)]
selftests/net: test classic bpf fanout mode
Test PACKET_FANOUT_CBPF by inserting a cBPF program that selects a
socket by payload. Requires modifying the test program to send
packets with multiple payloads.
Also fix a bug in testing the return value of mmap()
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 15 Aug 2015 02:31:35 +0000 (22:31 -0400)]
packet: add extended BPF fanout mode
Add fanout mode PACKET_FANOUT_EBPF that accepts an en extended BPF
program to select a socket.
Update the internal eBPF program by passing to socket option
SOL_PACKET/PACKET_FANOUT_DATA a file descriptor returned by bpf().
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 15 Aug 2015 02:31:34 +0000 (22:31 -0400)]
packet: add classic BPF fanout mode
Add fanout mode PACKET_FANOUT_CBPF that accepts a classic BPF program
to select a socket.
This avoids having to keep adding special case fanout modes. One
example use case is application layer load balancing. The QUIC
protocol, for instance, encodes a connection ID in UDP payload.
Also add socket option SOL_PACKET/PACKET_FANOUT_DATA that updates data
associated with the socket group. Fanout mode PACKET_FANOUT_CBPF is the
only user so far.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Fri, 14 Aug 2015 14:40:40 +0000 (16:40 +0200)]
lwtunnel: rename ip lwtunnel attributes
We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.
As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.
Fixes: 3093fbe7ff4b ("route: Per route IP tunnel metadata via lightweight tunnel") Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Mon, 17 Aug 2015 20:45:36 +0000 (13:45 -0700)]
smsc911x: Fix crash seen if neither ACPI nor OF is configured or used
Commit 0b50dc4fc971 ("Convert smsc911x to use ACPI as well as DT") makes
the call to smsc911x_probe_config() unconditional, and no longer fails if
there is no device node. device_get_phy_mode() is called unconditionally,
and if there is no phy node configured returns an error code. This error
code is assigned to phy_interface, and interpreted elsewhere in the code
as valid phy mode. This in turn causes qemu to crash when running a
variant of realview_pb_defconfig.
qemu: hardware error: lan9118_read: Bad reg 0x86
Fixes: 0b50dc4fc971 ("Convert smsc911x to use ACPI as well as DT") Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc Graeme Gregory <graeme.gregory@linaro.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 14 Aug 2015 01:34:03 +0000 (18:34 -0700)]
net: fix endian check warning in etherdevice.h
Sparse builds have been warning for a really long time now
that etherdevice.h has a conversion that is unsafe.
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
This code change fixes the issue and generates the exact
same assembly before/after (checked on x86_64)
Fixes: 2c722fe1c821 (etherdevice: Optimize a few is_<foo>_ether_addr functions) Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Aug 2015 18:50:25 +0000 (11:50 -0700)]
Merge branch 'iff_no_queue'
Phil Sutter says:
====================
net: introduce IFF_NO_QUEUE as successor of zero tx_queue_len
This series adds a new private net_device flag indicating that a device may
(and probably should) be used without a queueing discipline attached to it.
This is already common practice for many virtual device types like e.g.
loopback, VLAN (802.1Q) or bridges (802.1D). The reason for this is that these
devices lack an underlying layer which could impose back pressure and therefore
making a TX queue necessary to not slow down senders.
Up to now, drivers being aware of the above applying to them set
dev->tx_queue_len to zero to indicate no qdisc should be attached to the
interface they drive and the kernel reacts upon this by assigning the noop
qdisc instead of the default pfifo_fast. This implicit agreement though leads
to an inconvenient situation once a user tries to attach a real qdisc to these
devices, as the formerly special tx_queue_len value becomes a regular one,
limiting the queue to zero packets and thus prevents any TX from happening. To
overcome this, practically all qdisc implementations intercept and sanitize the
malicious value.
With this series applied, drivers may signal the lack of need for a qdisc
without having to tamper with tx_queue_len, making fallbacks in qdiscs and
caveats in userspace unnecessary.
Upon upstream acceptance, this series will be followed up by a set of patches
converting device drivers, adding a warning so out-of-tree driver authors get
aware of this change and dropping all special handling of tx_queue_len in
net/sched/.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 13 Aug 2015 17:01:06 +0000 (19:01 +0200)]
net: declare new net_device priv_flag IFF_NO_QUEUE
This private net_device flag can be set by drivers to inform that a
device runs fine without a qdisc attached. This was formerly done by
setting tx_queue_len to zero.
Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A zero length payload means that no TLV (Type Length Value) data has
been passed. Prior to this patch a non-existing TLV could be sanity
checked with TLV_OK() resulting in random behavior where a user
sending an empty message occasionally got a incorrect "operation not
supported" message back.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 17 Aug 2015 05:28:25 +0000 (08:28 +0300)]
bnx2: Fix bandwidth allocation for some MF modes
Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.
For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 15 Aug 2015 17:54:07 +0000 (10:54 -0700)]
ipv4: fix refcount leak in fib_check_nh()
fib_lookup() forces FIB_LOOKUP_NOREF flag, while fib_table_lookup()
does not.
This patch solves the typical message at reboot time or device
dismantle :
unregister_netdevice: waiting for eth0 to become free. Usage count = 4
Fixes: 3bfd847203c6 ("net: Use passed in table for nexthop lookups") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Ahern <dsa@cumulusnetworks.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 802.15.4 packet layer registration when mutliple
lowpan interfaces will be added. We need to register the packet layer at
the first lowpan interface and deregister it at the last interface. This
done by open_count variable which is protected by rtnl.
Additional do a quiet fix by adding dev_put(real_dev) when netdev
registration fails, which fix the refcount for the wpan dev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Simon Wunderlich [Wed, 24 Jun 2015 12:50:20 +0000 (14:50 +0200)]
batman-adv: remove broadcast packets scheduled for purged outgoing if
When an interface is purged, the broadcast packets scheduled for this
interface should get purged as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Linus Lüssing [Tue, 16 Jun 2015 15:10:26 +0000 (17:10 +0200)]
batman-adv: Fix potential synchronization issues in mcast tvlv handler
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Linus Lüssing [Tue, 16 Jun 2015 15:10:25 +0000 (17:10 +0200)]
batman-adv: Make MCAST capability changes atomic
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Linus Lüssing [Tue, 16 Jun 2015 15:10:24 +0000 (17:10 +0200)]
batman-adv: Make TT capability changes atomic
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: e17931d1a61d ("batman-adv: introduce capability initialization bitfield") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Linus Lüssing [Tue, 16 Jun 2015 15:10:23 +0000 (17:10 +0200)]
batman-adv: Make NC capability changes atomic
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Linus Lüssing [Tue, 16 Jun 2015 15:10:22 +0000 (17:10 +0200)]
batman-adv: Make DAT capability changes atomic
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Johannes Berg [Mon, 13 Jul 2015 10:17:25 +0000 (12:17 +0200)]
average: provide macro to create static EWMA
Having the EWMA parameters stored in the runtime struct imposes
memory requirements for the constant values that could just be
inlined in the code. This particularly makes sense if there are
a lot of such structs, for example in mac80211 in the station
table where each station has a number of these in an array, and
there can be many stations.
Provide a macro DECLARE_EWMA() that declares the necessary struct
and inline functions to access it with the parameters hard-coded;
using this also means the user no longer needs to 'select AVERAGE'
as it's entirely self-contained.
In the mac80211 case, on x86-64, this actually slightly *reduces*
code size, while also saving 80 bytes of runtime memory per sta.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Su Kang Yin [Fri, 7 Aug 2015 08:54:10 +0000 (16:54 +0800)]
mac80211_hwsim: unregister genetlink family properly
During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: remove ieee80211_tx_rate dependency in rate mask code
Remove ieee80211_tx_rate dependency in rate_idx_match_legacy_mask(),
rate_idx_match_mcs_mask() and rate_idx_match_mask() in order to use the
previous logic to define a ratemask in rate_control_set_rates() for
station rate table. Moreover move rate mask definition logic in
rate_control_cap_mask()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: remove ieee80211_tx_info from rate_control_apply_mask signature
Remove unnecessary ieee80211_tx_info pointer from rate_control_apply_mask
signature. rate_control_apply_mask() will be used to define a ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Mon, 3 Aug 2015 08:55:24 +0000 (10:55 +0200)]
cfg80211: propagate set_wiphy failure to userspace
If driver failed to setup wiphy params (e.g. rts
threshold, fragmentation treshold) userspace
wasn't properly notified about this. This could
lead to user confusion who would think the command
succeeded even if that wasn't the case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Matthias May [Fri, 17 Jul 2015 13:28:39 +0000 (15:28 +0200)]
cfg80211: regulatory: handle 5 and 10 MHz channels properly
The original assumption of 20MHz wide channels hasn't been true since
the addition of support for 5 and 10 MHz channels.
Change the code to no longer disable all channels that don't fit into
the 20MHz grid, but instead set the appropriate flags to disable
operation on specific bandwidths.
Signed-off-by: Matthias May <matthias.may@neratec.com>
[reword commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben YoungTae Kim [Fri, 14 Aug 2015 05:09:42 +0000 (22:09 -0700)]
Bluetooth: hciuart: Fix to use boolean flag with u32 type
debugfs_create_bool is asking to put u32 type pointer instead of bool
so that passing bool type with u32* cast will cause memory corruption
to read that value since it is handled by 4 bytes instead of 1 byte
inside.
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
David S. Miller [Fri, 14 Aug 2015 05:43:22 +0000 (22:43 -0700)]
Merge branch 'vrf-lite'
David Ahern says:
====================
VRF-lite - v6
In the context of internet scale routing a requirement that always comes
up is the need to partition the available routing tables into disjoint
routing planes. A specific use case is the multi-tenancy problem where
each tenant has their own unique routing tables and in the very least
need different default gateways.
This patch allows the ability to create virtual router domains (aka VRFs
(VRF-lite to be specific) in the linux packet forwarding stack. The main
observation is that through the use of rules and socket binding to interfaces,
all the facilities that we need are already present in the infrastructure. What
is missing is a handle that identifies a routing domain and can be used to
gather applicable rules/tables and uniqify neighbor selection. The scheme used
needs to preserves the notions of ECMP, and general routing principles.
This driver is a cross between functionality that the IPVLAN driver
and the Team drivers provide where a device is created and packets
into/out of the routing domain are shuttled through this device. The
device is then used as a handle to identify the applicable rules. The
VRF device is thus the layer3 equivalent of a vlan device.
The very important point to note is that this is only a Layer3 concept
so L2 tools (e.g., LLDP) do not need to be run in each VRF, processes can
run in unaware mode or select a VRF to be talking through. Also the
behavioral model is a generalized application of the familiar VRF-Lite
model with some performance paths that need optimization. (Specifically
the output route selector that Roopa, Robert, Thomas and EricB are
currently discussing on the MPLS thread)
High Level points
=================
1. Simple overlay driver (minimal changes to current stack)
* uses the existing fib tables and fib rules infrastructure
2. Modelled closely after the ipvlan driver
3. Uses current API and infrastructure.
* Applications can use SO_BINDTODEVICE or cmsg device indentifiers
to pick VRF (ping, traceroute just work)
* Standard IP Rules work, and since they are aggregated against the
device, scale is manageable
4. Completely orthogonal to Namespaces and only provides separation in
the routing plane (and ARP)
Given the topology above, the setup needed to get the basic VRF
functions working would be
Create the VRF devices and associate with a table
ip link add vrf1 type vrf table 5
ip link add vrf2 type vrf table 6
Install the lookup rules that map table to VRF domain
ip rule add pref 200 oif vrf1 lookup 5
ip rule add pref 200 iif vrf1 lookup 5
ip rule add pref 200 oif vrf2 lookup 6
ip rule add pref 200 iif vrf2 lookup 6
ip link set vrf1 up
ip link set vrf2 up
Enslave the routing member interfaces
ip link set swp1 master vrf1
ip link set swp2 master vrf1
ip link set swp3 master vrf2
ip link set swp4 master vrf2
Connected and local routes are automatically moved from main and local
tables to the VRF table.
ping using VRF0 is simply
ping -I vrf0 10.0.1.2
Design Highlights
=================
If a device is enslaved to a VRF device (ie., associated with a VRF)
then:
1. Rx path
The master device index is used as the iif for all lookups.
2. Tx path
Similarly, for Tx the VRF device oif is used in the flow to direct
lookups to the table associated with the VRF via its rule. From there
the FLOWI_FLAG_VRFSRC flag is used to indicate that the oif should
not be used for FIB table lookups.
3. Connected and local routes
On link up for a device, connected and local routes are added to the
table associated with the VRF device, rather than the local and main
tables.
4. Socket lookups
Sockets operating in the VRF must be bound to the VRF device. As such
socket lookups compare the VRF device index to sk_bound_dev_if.
5. Neighbor entries
Neighbor entries are not impacted by the VRF device. Entries are
associated with a particular interface; the VRF association is indirect
via the interface-to-VRF device enslavement.
Version 6
- addressed comments from DaveM
- added patch to properly set oif in ip_send_unicast_reply. Needs to be
set to VRF device for proper FIB lookup
- added patch to handle IP fragments
Version 5
- dropped patch regarding socket lookups; no longer needed
+ removed vrf helpers no longer needed after this patch is dropped
- removed dev_open and close operations
+ no need to reset vrf data on an ifdown and creates problems if a
slave is deleted while the vrf interface is down (Thanks, Nikolay)
- cleanups for sparse warnings
+ make C=2 is now clean for vrf driver
Version 4
- builds are clean with and without VRF device enabled (no, yes and module)
- tightened the driver implementation
+ device add/delete, slave add/remove, and module unload are all clean
- fixed RCU references
+ with RCU and lock debugging enabled changes are clean through the
suite of tests
- TX path uses custom dst, so patch refactoring rtable allocation is
dropped along with the patch adding rt_nexthop helper
- dropped the task patch that adds default bind to interface for sockets
and the associated chvrf example command
+ the patches are a convenience for running unmodified code. They
are not needed for the core functionality. Any application with
support for SO_BINDTODEVICE works properly with this patch set.
Version 3
- addressed comments from first 2 RFCs with the exception of the name
Nicolas: We will do the name conversion once we agree on what the
correct name should be (vrf, mrf or something else)
- packets flow through the VRF device in both directions allowing the
following:
- tcpdump -i vrf<n>
- tc rules on vrf device
- netfilter rules on vrf device
TO-DO
=====
1. IPv6
2. ipsec, xfrms
- dst patch accepted into ipsec-next; will post VRF patch once merge happens
3. listen filter to allow 1 socket to work with multiple VRF devices
- i.e., bind to VRF's a, b, c only or NOT VRFs e, f, g
Eric B:
I have ipsec working with VRFs implemented using the VRF driver,
including the worst case scenario of complete duplication in the
networking config.
Thanks to Nikolay for his many, many code reviews whipping the device
driver into shape, and bug-Fixes and ideas from Hannes, Roopa Prabhu,
Jon Toppins, Jamal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:10 +0000 (14:59 -0600)]
net: Introduce VRF device driver
This driver borrows heavily from IPvlan and teaming drivers.
Routing domains (VRF-lite) are created by instantiating a VRF master
device with an associated table and enslaving all routed interfaces that
participate in the domain. As part of the enslavement, all connected
routes for the enslaved devices are moved to the table associated with
the VRF device. Outgoing sockets must bind to the VRF device to function.
Standard FIB rules bind the VRF device to tables and regular fib rule
processing is followed. Routed traffic through the box, is forwarded by
using the VRF device as the IIF and following the IIF rule to a table
that is mated with the VRF.
Example:
Create vrf 1:
ip link add vrf1 type vrf table 5
ip rule add iif vrf1 table 5
ip rule add oif vrf1 table 5
ip route add table 5 prohibit default
ip link set vrf1 up
Add interface to vrf 1:
ip link set eth1 master vrf1
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:09 +0000 (14:59 -0600)]
net: frags: Add VRF device index to cache and lookup
Fragmentation cache uses information from the IP header to reassemble
packets. That information can be duplicated across VRFs -- same source
and destination addresses, protocol and id. Handle fragmentation with
VRFs by adding the VRF device index to entries in the cache and the
lookup arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:07 +0000 (14:59 -0600)]
net: Use passed in table for nexthop lookups
If a user passes in a table for new routes use that table for nexthop
lookups. Specifically, this solves the case where a connected route does
not exist in the main table, but only another table and then a subsequent
route is added with a next hop using the connected route. ie.,
$ ip route ls
default via 10.0.2.2 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
169.254.0.0/16 dev eth0 scope link metric 1003
192.168.56.0/24 dev eth1 proto kernel scope link src 192.168.56.51
$ ip route ls table 10
1.1.1.0/24 dev eth2 scope link
Without this patch adding a nexthop route fails:
$ ip route add table 10 2.2.2.0/24 via 1.1.1.10
RTNETLINK answers: Network is unreachable
With this patch the route is added successfully.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:06 +0000 (14:59 -0600)]
net: Add routes to the table associated with the device
When a device associated with a VRF is brought up or down routes
should be added to/removed from the table associated with the VRF.
fib_magic defaults to using the main or local tables. Have it use
the table with the device if there is one.
A part of this is directing prefsrc validations to the correct
table as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:05 +0000 (14:59 -0600)]
net: Fix up inet_addr_type checks
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:04 +0000 (14:59 -0600)]
net: Add inet_addr lookup by table
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:03 +0000 (14:59 -0600)]
udp: Handle VRF device in sendmsg
For unconnected UDP sockets using a VRF device lookup source address
based on VRF table. This allows the UDP header to be properly setup
before showing up at the VRF device via the dst.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:02 +0000 (14:59 -0600)]
net: Use VRF device index for lookups on TX
As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:01 +0000 (14:59 -0600)]
net: Use VRF device index for lookups on RX
On ingress use index of VRF master device for route lookups if real device
is enslaved. Rules are expected to be installed for the VRF device to
direct lookups to a specific table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Aug 2015 20:59:00 +0000 (14:59 -0600)]
net: Introduce VRF related flags and helpers
Add a VRF_MASTER flag for interfaces and helper functions for determining
if a device is a VRF_MASTER.
Add link attribute for passing VRF_TABLE id.
Add vrf_ptr to netdevice.
Add various macros for determining if a device is a VRF device, the index
of the master VRF device and table associated with VRF device.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Thu, 13 Aug 2015 19:26:35 +0000 (15:26 -0400)]
net: addr IFLA_OPERSTATE to netlink message for ipv6 ifinfo
This is useful information to include in ipv6 netlink messages that
report interface information. IFLA_OPERSTATE is already included in
ipv4 messages, but missing for ipv6. This closes that gap.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Levin [Thu, 13 Aug 2015 18:03:16 +0000 (14:03 -0400)]
net: allow sleeping when modifying store_rps_map
Commit 10e4ea751 ("net: Fix race condition in store_rps_map") has moved the
manipulation of the rps_needed jump label under a spinlock. Since changing
the state of a jump label may sleep this is incorrect and causes warnings
during runtime.
Make rps_map_lock a mutex to allow sleeping under it.
Fixes: 10e4ea751 ("net: Fix race condition in store_rps_map") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Aug 2015 04:31:14 +0000 (21:31 -0700)]
Merge branch 'mv88e6xxx-hw-vlan'
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: add hardware VLAN support
This patchset brings support to access hardware VLAN entries in DSA and
mv88e6xxx, through switchdev VLAN objects.
In the following example, ports swp[0-2] belong to bridge br0, and ports
swp[3-4] belong to bridge br1. Here's an example of what can be achieved
after this patchset:
# bridge vlan add dev swp1 vid 100 master
# bridge vlan add dev swp2 vid 100 master
# bridge vlan add dev swp3 vid 100 master
# bridge vlan add dev swp4 vid 100 master
# bridge vlan del dev swp1 vid 100 master
The above commands correctly programmed hardware VLAN 100 for port swp2,
while ports swp3 and swp4 use software VLAN 100, as shown with:
Vivien Didelot [Thu, 13 Aug 2015 16:52:21 +0000 (12:52 -0400)]
net: dsa: mv88e6xxx: add VLAN Purge support
Add support for the VTU Load Purge operation and implement the
port_vlan_del driver function to remove a port from a VLAN entry, and
delete the VLAN if the given port was its last member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 13 Aug 2015 16:52:20 +0000 (12:52 -0400)]
net: dsa: mv88e6xxx: add VLAN support to FDB dump
Add an helper function to read the next valid VLAN entry for a given
port. It is used in the VID to FID conversion function to retrieve the
forwarding database assigned to a given VLAN port.
Finally update the FDB getnext operation to iterate on the next valid
port VLAN when the end of the current database is reached.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 13 Aug 2015 16:52:19 +0000 (12:52 -0400)]
net: dsa: mv88e6xxx: add VLAN Get Next support
Implement the port_pvid_get and vlan_getnext driver functions required
to dump VLAN entries from the hardware, with the VTU Get Next operation.
Some functions and structure will be shared with STU operations, since
their table format are similar (e.g. STU data entries are accessible
with the same registers as VTU entries, except with an offset of 2).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 13 Aug 2015 16:52:17 +0000 (12:52 -0400)]
net: dsa: add support for switchdev VLAN objects
Add new functions in DSA drivers to access hardware VLAN entries through
SWITCHDEV_OBJ_PORT_VLAN objects:
- port_pvid_get() and vlan_getnext() to dump a VLAN
- port_vlan_del() to exclude a port from a VLAN
- port_pvid_set() and port_vlan_add() to join a port to a VLAN
The DSA infrastructure will ensure that each VLAN of the given range
does not already belong to another bridge. If it does, it will fallback
to software VLAN and won't program the hardware.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Thu, 13 Aug 2015 14:39:01 +0000 (10:39 -0400)]
net: ipv6 sysctl option to ignore routes when nexthop link is down
Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link. The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:
When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.
1000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
1000::/8 via 8000::2 dev p8p1 metric 1024 pref medium
7000::/8 dev p7p1 proto kernel metric 256 dead linkdown pref medium
8000::/8 dev p8p1 proto kernel metric 256 pref medium
9000::/8 via 8000::2 dev p8p1 metric 2048 pref medium
9000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
fe80::/64 dev p7p1 proto kernel metric 256 dead linkdown pref medium
fe80::/64 dev p8p1 proto kernel metric 256 pref medium
This also adds devconf support and notification when sysctl values
change.
v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Thu, 13 Aug 2015 14:39:00 +0000 (10:39 -0400)]
net: track link status of ipv6 nexthops
Add support to track current link status of ipv6 nexthops to match
recent changes that added support for ipv4 nexthops. This takes a
simple approach to track linkdown status for next-hops and simply
checks the dev for the dst entry and sets proper flags that to be used
in the netlink message.
v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 13 Aug 2015 01:45:25 +0000 (18:45 -0700)]
rocker: hook ndo_neigh_destroy to cleanup neigh refs in driver
Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops. The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down). This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device. In response, the driver will
purge the neigh entry from its internal tbl.
I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users. In any case, it
does what I need here. An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 13 Aug 2015 23:58:29 +0000 (16:58 -0700)]
Merge branch 'smsc911x-acpi'
Jeremy Linton says:
====================
Enable smsc911x for use with ACPI
This set of patches enables the front Ethernet port on the
ARM Juno development platform when used with an ACPI enabled kernel.
These patches covert the of_property* calls in the driver to the
DT/ACPI agnostic device_property* calls, and add the arm hardware
id to the acpi_match_table.
To support the above changes I copied a couple routines from
of_net into the properties.c file, and modified them to
be ACPI/DT agnostic. I'm not 100% sure this is the correct location
for these functions. But I think they are required to avoid having
a dozen different implementations scattered across assorted Ethernet
adapters that are being enabled to use ACPI properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log