David Sterba [Wed, 29 Mar 2017 18:48:44 +0000 (20:48 +0200)]
btrfs: use clear_page where appropriate
There's a helper to clear whole page, with a arch-specific optimized
code. The replaced cases do not seem to be in performace critical code,
but we still might get some percent gain.
Qu Wenruo [Wed, 29 Mar 2017 01:33:22 +0000 (09:33 +0800)]
btrfs: Prevent scrub recheck from racing with dev replace
scrub_setup_recheck_block() calls btrfs_map_sblock() and then accesses
bbio without protection of bio_counter.
This can lead to use-after-free if racing with dev replace cancel.
Fix it by increasing bio_counter before calling btrfs_map_sblock() and
decreasing the bio_counter when corresponding recover is finished.
Cc: Liu Bo <bo.li.liu@oracle.com> Reported-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 29 Mar 2017 01:33:21 +0000 (09:33 +0800)]
btrfs: Wait for in-flight bios before freeing target device for raid56
When raid56 dev-replace is cancelled by running scrub, we will free
target device without waiting for in-flight bios, causing the following
NULL pointer deference or general protection failure.
In btrfs_dev_replace_finishing(), we will call
btrfs_rm_dev_replace_blocked() to wait bios before destroying the target
device when scrub is finished normally.
However when dev-replace is aborted, either due to error or cancelled by
scrub, we didn't wait for bios, this can lead to use-after-free if there
are bios holding the target device.
Furthermore, for raid56 scrub, at least 2 places are calling
btrfs_map_sblock() without protection of bio_counter, leading to the
problem.
This patch fixes the problem:
1) Wait for bio_counter before freeing target device when canceling
replace
2) When calling btrfs_map_sblock() for raid56, use bio_counter to
protect the call.
Cc: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
The reason is that after raid56 read rebuild rbio->stripe_pages are all
correctly recovered (0xcd for data stripes).
However when we check and repair parity in
scrub_parity_check_and_repair(), we will append pages in sparity->spages
list to rbio->bio_pages[], which contains old on-disk data.
And when we submit parity data to disk, we calculate parity using
rbio->bio_pages[] first, if rbio->bio_pages[] not found, then fallback
to rbio->stripe_pages[].
The patch fix it by not appending pages from sparity->spages.
So finish_parity_scrub() will use rbio->stripe_pages[] which is correct.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 13 Mar 2017 07:52:09 +0000 (15:52 +0800)]
btrfs: qgroup: Re-arrange tracepoint timing to co-operate with reserved space tracepoint
Newly introduced qgroup reserved space trace points are normally nested
into several common qgroup operations.
While some other trace points are not well placed to co-operate with
them, causing confusing output.
This patch re-arrange trace_btrfs_qgroup_release_data() and
trace_btrfs_qgroup_free_delayed_ref() trace points so they are triggered
before reserved space ones.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Reviewed-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Wed, 29 Mar 2017 17:54:26 +0000 (10:54 -0700)]
Btrfs: fix wrong failed mirror_num of read-repair on raid56
In raid56 scenario, after trying parity recovery, we didn't set
mirror_num for btrfs_bio with failed mirror_num, hence
end_bio_extent_readpage() will report a random mirror_num in dmesg
log.
Cc: David Sterba <dsterba@suse.cz> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Wed, 29 Mar 2017 17:55:16 +0000 (10:55 -0700)]
Btrfs: set scrub page's io_error if failing to submit io
Scrub repairs data by the unit called scrub_block, which may contain
several pages. Scrub always tries to look up a good copy of a whole
block, but if there's no such copy, it tries to do repair page by page.
If we don't set page's io_error when checking this bad copy, in the last
step, we may skip this page when repairing bad copy from good copy.
Cc: David Sterba <dsterba@suse.cz> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 28 Mar 2017 12:44:21 +0000 (14:44 +0200)]
btrfs: track exclusive filesystem operation in flags
There are several operations, usually started from ioctls, that cannot
run concurrently. The status is tracked in
mutually_exclusive_operation_running as an atomic_t. We can easily track
the status as one of the per-filesystem flag bits with same
synchronization guarantees.
btrfs: qgroups: Retry after commit on getting EDQUOT
We are facing the same problem with EDQUOT which was experienced with
ENOSPC. Not sure if we require a full ticketing system such as ENOSPC, but
here is a quick fix, which may be too big a hammer.
Quotas are reserved during the start of an operation, incrementing
qg->reserved. However, it is written to disk in a commit_transaction
which could take as long as commit_interval. In the meantime there
could be deletions which are not accounted for because deletions are
accounted for only while committed (free_refroot). So, when we get
a EDQUOT flush the data to disk and try again.
David Sterba [Wed, 15 Mar 2017 15:17:03 +0000 (16:17 +0100)]
btrfs: remove unused qgroup members from btrfs_trans_handle
The members have been effectively unused since "Btrfs: rework qgroup
accounting" (fcebe4562dec83b3), there's no substitute for
assert_qgroups_uptodate so it's removed as well.
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 2 Mar 2017 17:54:52 +0000 (18:54 +0100)]
btrfs: preallocate radix tree node for global readahead tree
We can preallocate the node so insertion does not have to do that under
the lock. The GFP flags for the global radix tree are initialized to
GFP_NOFS & ~__GFP_DIRECT_RECLAIM
but we can use GFP_KERNEL, because readahead is optional and not on any
critical writeout path.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 2 Mar 2017 17:54:52 +0000 (18:54 +0100)]
btrfs: preallocate radix tree node for readahead
We can preallocate the node so insertion does not have to do that under
the lock. The GFP flags for the per-device radix tree are initialized to
GFP_NOFS & ~__GFP_DIRECT_RECLAIM
but we can use GFP_KERNEL, same as an allocation above anyway, but also
because readahead is optional and not on any critical writeout path.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
The btrfs_balance_args are only used for the balance ioctl, so use __u
instead of __le here for consistency. The __le usage was introduced in bc3094673f22d and dee32d0ac3719 and was probably a result of
copy/pasting when the code was written.
The usage of __le did not break anything, but it's unnecessary. Also,
this change makes the code less confusing for the careful reader.
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Tue, 14 Mar 2017 20:33:56 +0000 (13:33 -0700)]
Btrfs: separate DISCARD from __btrfs_map_block
Since DISCARD is not as important as an operation like write, we don't
copy it to target device during replace, and it makes __btrfs_map_block
less complex.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Fri, 10 Mar 2017 19:09:48 +0000 (11:09 -0800)]
Btrfs: add file item tracepoints
While debugging truncate problems, I found that these tracepoints could
help us quickly know what went wrong.
Two sets of tracepoints are created to track regular/prealloc file item
and inline file item respectively, I put inline as a separate one since
what inline file items cares about are way less than the regular one.
This adds four tracepoints:
- btrfs_get_extent_show_fi_regular
- btrfs_get_extent_show_fi_inline
- btrfs_truncate_show_fi_regular
- btrfs_truncate_show_fi_inline
Cc: David Sterba <dsterba@suse.cz> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ formatting adjustments ] Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:26 +0000 (10:55 +0200)]
btrfs: convert btrfs_raid_bio.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:25 +0000 (10:55 +0200)]
btrfs: convert scrub_ctx.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:24 +0000 (10:55 +0200)]
btrfs: convert scrub_parity.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:23 +0000 (10:55 +0200)]
btrfs: convert scrub_block.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:21 +0000 (10:55 +0200)]
btrfs: convert scrub_recover.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:20 +0000 (10:55 +0200)]
btrfs: convert compressed_bio.pending_bios from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:19 +0000 (10:55 +0200)]
btrfs: convert extent_state.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:18 +0000 (10:55 +0200)]
btrfs: convert btrfs_root.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:17 +0000 (10:55 +0200)]
btrfs: convert btrfs_delayed_item.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:16 +0000 (10:55 +0200)]
btrfs: convert btrfs_delayed_node.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:15 +0000 (10:55 +0200)]
btrfs: convert btrfs_delayed_ref_node.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:14 +0000 (10:55 +0200)]
btrfs: convert btrfs_caching_control.count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:13 +0000 (10:55 +0200)]
btrfs: convert btrfs_ordered_extent.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:12 +0000 (10:55 +0200)]
btrfs: convert extent_map.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:11 +0000 (10:55 +0200)]
btrfs: convert btrfs_transaction.use_count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Elena Reshetova [Fri, 3 Mar 2017 08:55:10 +0000 (10:55 +0200)]
btrfs: convert btrfs_bio.refs from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Fri, 3 Mar 2017 02:41:19 +0000 (18:41 -0800)]
Btrfs: remove ASSERT in btrfs_truncate_inode_items
After 76b42abbf748 ("Btrfs: fix data loss after truncate when using the
no-holes feature"),
For either NO_HOLES or inline extents, we've set last_size to newsize to
avoid data loss after remount or inode got evicted and read again, thus,
we don't need this check anymore.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
Adam Borowski [Tue, 7 Mar 2017 22:34:44 +0000 (23:34 +0100)]
btrfs: fix a bogus warning when converting only data or metadata
If your filesystem has, eg, data:raid0 metadata:raid1, and you run "btrfs
balance -dconvert=raid1", the meta.target field will be uninitialized.
That's otherwise ok, as it's unused except for this warning.
Thus, let's use the existing set of raid levels for the comparison.
As a side effect, non-convert balances will now nag about data>metadata.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Four small fixes.
Three of them fix the same error in NVMe, in loop, fc, and rdma
respectively. The last fix from Ming fixes a regression in this
series, where our bvec gap logic was wrong and causes an oops on
NVMe for certain conditions"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bio_will_gap() for first bvec with offset
nvme-fc: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-rdma: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-loop: Fix sqsize wrong assignment based on ctrl MQES capability
Olof Johansson [Sun, 16 Apr 2017 18:52:26 +0000 (11:52 -0700)]
Merge tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Merge branch 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"Unfortunately, the commit to fix the cgroup mount race in the previous
pull request can lead to hangs.
The original bug has been around for a while and isn't too likely to
be triggered in usual use cases. Revert the commit for now"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Revert "cgroup: avoid attaching a cgroup root to two different superblocks"
Merge tag 'tty-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fix from Greg KH:
"Here is a single tty core revert for a patch that was reported to
cause problems.
The original issue is one that we have lived with for decades, so
trying to scramble to fix the fix in time for 4.11-final does not make
sense due to the fragility of the tty ldisc layer. Just reverting it
makes sense for now"
* tag 'tty-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: don't panic on OOM in tty_set_ldisc()"
Merge tag 'trace-v4.11-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"While rewriting the function probe code, I stumbled over a long
standing bug. This bug has been there sinc function tracing was added
way back when. But my new development depends on this bug being fixed,
and it should be fixed regardless as it causes ftrace to disable
itself when triggered, and a reboot is required to enable it again.
The bug is that the function probe does not disable itself properly if
there's another probe of its type still enabled. For example:
The above registers two traceoff probes (one for schedule and one for
do_IRQ, and then removes do_IRQ.
But since there still exists one for schedule, it is not done
properly. When adding do_IRQ back, the breakage in the accounting is
noticed by the ftrace self tests, and it causes a warning and disables
ftrace"
* tag 'trace-v4.11-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix removing of second function probe
Andrei reports CRIU test hangs with the patch applied. The bug fixed
by the patch isn't too likely to trigger in actual uses. Revert the
patch for now.
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fixes from Dan Williams:
"A small crop of lockdep, sleeping while atomic, and other fixes /
band-aids in advance of the full-blown reworks targeting the next
merge window. The largest change here is "libnvdimm: fix blk free
space accounting" which deletes a pile of buggy code that better
testing would have caught before merging. The next change that is
borderline too big for a late rc is switching the device-dax locking
from rcu to srcu, I couldn't think of a smaller way to make that fix.
The __copy_user_nocache fix will have a full replacement in 4.12 to
move those pmem special case considerations into the pmem driver. The
"libnvdimm: band aid btt vs clear poison locking" commit admits that
our error clearing support for btt went in broken, so we just disable
it in 4.11 and -stable. A replacement / full fix is in the pipeline
for 4.12
Some of these would have been caught earlier had DEBUG_ATOMIC_SLEEP
been enabled on my development station. I wonder if we should have:
config DEBUG_ATOMIC_SLEEP
default PROVE_LOCKING
...since I mistakenly thought I got both with PROVE_LOCKING=y.
These have received a build success notification from the 0day robot,
and some have appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
x86, pmem: fix broken __copy_user_nocache cache-bypass assumptions
device-dax: switch to srcu, fix rcu_read_lock() vs pte allocation
libnvdimm: band aid btt vs clear poison locking
libnvdimm: fix reconfig_mutex, mmap_sem, and jbd2_handle lockdep splat
libnvdimm: fix blk free space accounting
acpi, nfit, libnvdimm: fix interleave set cookie calculation (64-bit comparison)
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is seven small fixes which are all for user visible issues that
fortunately only occur in rare circumstances.
The most serious is the sr one in which QEMU can cause us to read
beyond the end of a buffer (I don't think it's exploitable, but just
in case).
The next is the sd capacity fix which means all non 512 byte sector
drives greater than 2TB fail to be correctly sized.
The rest are either in new drivers (qedf) or on error legs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
scsi: aacraid: fix PCI error recovery path
scsi: sd: Fix capacity calculation with 32-bit sector_t
scsi: qla2xxx: Add fix to read correct register value for ISP82xx.
scsi: qedf: Fix crash due to unsolicited FIP VLAN response.
scsi: sr: Sanity check returned mode data
scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable
Merge branch 'parisc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Mikulas Patocka fixed a few bugs in our new pa_memcpy() assembler
function, e.g. one bug made the kernel unbootable if source and
destination address are the same"
* 'parisc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix bugs in pa_memcpy
[ 1337.483798] ================================================
[ 1337.483999] [ BUG: lock held when returning to user space! ]
[ 1337.484252] 4.11.0-rc6 #19 Not tainted
[ 1337.484423] ------------------------------------------------
[ 1337.484626] mount/14766 is leaving the kernel with locks still held!
[ 1337.484841] 1 lock held by mount/14766:
[ 1337.485017] #0: (&type->s_umount_key#33/1){+.+.+.}, at: [<ffffffff8124171f>] sget_userns+0x2af/0x520
Caught by xfstests generic/413 which tried to mount with the unsupported
mount option dax. Then xfstests generic/422 ran sync which deadlocks.
Signed-off-by: Martin Brandenburg <martin@omnibond.com> Acked-by: Mike Marshall <hubcap@omnibond.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normal pathname lookup doesn't allow empty pathnames, but using
AT_EMPTY_PATH (with name_to_handle_at() or fstatat(), for example) you
can trigger an empty pathname lookup.
And not only is the RCU lookup in that case entirely unnecessary
(because we'll obviously immediately finalize the end result), it is
actively wrong.
Why? An empth path is a special case that will return the original
'dirfd' dentry - and that dentry may not actually be RCU-free'd,
resulting in a potential use-after-free if we were to initialize the
path lazily under the RCU read lock and depend on complete_walk()
finalizing the dentry.
The patch 554bfeceb8a22d448cd986fc9efce25e833278a1 ("parisc: Fix access
fault handling in pa_memcpy()") reimplements the pa_memcpy function.
Unfortunatelly, it makes the kernel unbootable. The crash happens in the
function ide_complete_cmd where memcpy is called with the same source
and destination address.
This patch fixes a few bugs in pa_memcpy:
* When jumping to .Lcopy_loop_16 for the first time, don't skip the
instruction "ldi 31,t0" (this bug made the kernel unbootable)
* Use the COND macro when comparing length, so that the comparison is
64-bit (a theoretical issue, in case the length is greater than
0xffffffff)
* Don't use the COND macro after the "extru" instruction (the PA-RISC
specification says that the upper 32-bits of extru result are undefined,
although they are set to zero in practice)
* Fix exception addresses in .Lcopy16_fault and .Lcopy8_fault
* Rename .Lcopy_loop_4 to .Lcopy_loop_8 (so that it is consistent with
.Lcopy8_fault)
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a small update to xpad driver to recognize yet another gamepad,
and another change making sure userio.h is exported"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add support for Razer Wildcat gamepad
uapi: add missing install of userio.h
Pull networking fixes from David Miller:
"Things seem to be settling down as far as networking is concerned,
let's hope this trend continues...
1) Add iov_iter_revert() and use it to fix the behavior of
skb_copy_datagram_msg() et al., from Al Viro.
2) Fix the protocol used in the synthetic SKB we cons up for the
purposes of doing a simulated route lookup for RTM_GETROUTE
requests. From Florian Larysch.
3) Don't add noop_qdisc to the per-device qdisc hashes, from Cong
Wang.
4) Don't call netdev_change_features with the team lock held, from
Xin Long.
5) Revert TCP F-RTO extension to catch more spurious timeouts because
it interacts very badly with some middle-boxes. From Yuchung
Cheng.
6) Fix the loss of error values in l2tp {s,g}etsockopt calls, from
Guillaume Nault.
7) ctnetlink uses bit positions where it should be using bit masks,
fix from Liping Zhang.
8) Missing RCU locking in netfilter helper code, from Gao Feng.
9) Avoid double frees and use-after-frees in tcp_disconnect(), from
Eric Dumazet.
10) Don't do a changelink before we register the netdevice in
bridging, from Ido Schimmel.
11) Lock the ipv6 device address list properly, from Rabin Vincent"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
netfilter: ipt_CLUSTERIP: Fix wrong conntrack netns refcnt usage
netfilter: nft_hash: do not dump the auto generated seed
drivers: net: usb: qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201
ipv6: Fix idev->addr_list corruption
net: xdp: don't export dev_change_xdp_fd()
bridge: netlink: register netdevice before executing changelink
bridge: implement missing ndo_uninit()
bpf: reference may_access_skb() from __bpf_prog_run()
tcp: clear saved_syn in tcp_disconnect()
netfilter: nf_ct_expect: use proper RCU list traversal/update APIs
netfilter: ctnetlink: skip dumping expect when nfct_help(ct) is NULL
netfilter: make it safer during the inet6_dev->addr_list traversal
netfilter: ctnetlink: make it safer when checking the ct helper name
netfilter: helper: Add the rcu lock when call __nf_conntrack_helper_find
netfilter: ctnetlink: using bit to represent the ct event
netfilter: xt_TCPMSS: add more sanity tests on tcph->doff
net: tcp: Increase TCP_MIB_OUTRSTS even though fail to alloc skb
l2tp: don't mask errors in pppol2tp_getsockopt()
l2tp: don't mask errors in pppol2tp_setsockopt()
tcp: restrict F-RTO to work-around broken middle-boxes
...
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of small fixes for x86:
- fix locking in RDT to prevent memory leaks and freeing in use
memory
- prevent setting invalid values for vdso32_enabled which cause
inconsistencies for user space resulting in application crashes.
- plug a race in the vdso32 code between fork and sysctl which causes
inconsistencies for user space resulting in application crashes.
- make MPX signal delivery work in compat mode
- make the dmesg output of traps and faults readable again"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix locking in rdtgroup_schemata_write()
x86/debug: Fix the printk() debug output of signal_fault(), do_trap() and do_general_protection()
x86/vdso: Plug race between mapping and ELF header setup
x86/vdso: Ensure vdso32_enabled gets set to valid values only
x86/signals: Fix lower/upper bound reporting in compat siginfo
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"The irq department provides:
- two fixes for the CPU affinity spread infrastructure to prevent
unbalanced spreading in corner cases which leads to horrible
performance, because interrupts are rather aggregated than spread
- add a missing spinlock initializer in the imx-gpcv2 init code"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-imx-gpcv2: Fix spinlock initialization
irq/affinity: Fix extra vecs calculation
irq/affinity: Fix CPU spread for unbalanced nodes
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Three fixes from EFI land:
- prevent accessing a Graphic Output Device (GOP) which the kernel
does not know to handle
- prevent PCI reconfiguration to modify a BAR which covers the
framebuffer because that's already in use through the EFI GOP
interface
- avoid reserving EFI runtime regions as this results in bogus memory
mappings"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't try to reserve runtime regions
efi/fb: Avoid reconfiguration of BAR that covers the framebuffer
efi/libstub: Skip GOP with PIXEL_BLT_ONLY format
Merge branch 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Dave Sterba collected a few more fixes for the last rc.
These aren't marked for stable, but I'm putting them in with a batch
were testing/sending by hand for this release"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix potential use-after-free for cloned bio
Btrfs: fix segmentation fault when doing dio read
Btrfs: fix invalid dereference in btrfs_retry_endio
btrfs: drop the nossd flag when remounting with -o ssd
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull more CIFS fixes from Steve French:
"As promised, here is the remaining set of cifs/smb3 fixes for stable
(and a fix for one regression) now that they have had additional
review and testing"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix SMB3 mount without specifying a security mechanism
CIFS: store results of cifs_reopen_file to avoid infinite wait
CIFS: remove bad_network_name flag
CIFS: reconnect thread reschedule itself
CIFS: handle guest access errors to Windows shares
CIFS: Fix null pointer deref during read resp processing
When two function probes are added to set_ftrace_filter, and then one of
them is removed, the update to the function locations is not performed, and
the record keeping of the function states are corrupted, and causes an
ftrace_bug() to occur.
This is easily reproducable by adding two probes, removing one, and then
adding it back again.
Cc: stable@vger.kernel.org Fixes: 59df055f1991 ("ftrace: trace different functions with a different tracer") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Ming Lei [Fri, 14 Apr 2017 19:58:29 +0000 (13:58 -0600)]
block: fix bio_will_gap() for first bvec with offset
Commit 729204ef49ec("block: relax check on sg gap") allows us to merge
bios, if both are physically contiguous. This change can merge a huge
number of small bios, through mkfs for example, mkfs.ntfs running time
can be decreased to ~1/10.
But if one rq starts with a non-aligned buffer (the 1st bvec's bv_offset
is non-zero) and if we allow the merge, it is quite difficult to respect
sg gap limit, especially the max segment size, or we risk having an
unaligned virtual boundary. This patch tries to avoid the issue by
disallowing a merge, if the req starts with an unaligned buffer.
Also add comments to explain why the merged segment can't end in
unaligned virt boundary.
Fixes: 729204ef49ec ("block: relax check on sg gap") Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Ming Lei <ming.lei@redhat.com>
Rewrote parts of the commit message and comments.
Merge tag 'fbdev-v4.11-rc6' of git://github.com/bzolnier/linux
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- fix probing time checks in omapfb driver (regression fix)
- fix optional VBAT support in ssd1307fb driver (regression fix)
- fix connecting to backend in xen-fbfront driver
* tag 'fbdev-v4.11-rc6' of git://github.com/bzolnier/linux:
fbdev: omapfb: delete check_required_callbacks()
xen, fbfront: fix connecting to backend
fbdev/ssd1307fb: fix optional VBAT support
Merge tag 'pm-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a cpufreq core regression related to CPU online/offline and
several issues in the turbostat and cpupower utilities.
Specifics:
- Allow CPUs to be put back online even if the cpufreq driver is
unable to work with them (eg. due to missing information from
platform firmware), which was the previous behavior expected by
users, but changed in the 4.9 time frame (Chen Yu).
- Fix a few minor issues in the turbostat utility, introduced mostly
during the recent update of it (Len Brown, Doug Smythies).
- Fix a cpupower utility bug causing it to report incorrect values
for turbo frequencies in some cases (Ben Hutchings)"
* tag 'pm-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpupower: Fix turbo frequency reporting for pre-Sandy Bridge cores
cpufreq: Bring CPUs up even if cpufreq_online() failed
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
Merge tag 'acpi-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a recent ACPICA commit that turned out to be problematic
and fix a device enumeration breakage from the 4.8 cycle.
Specifics:
- Revert a recent ACPICA commit targeted at catching firmware bugs
which promptly did that and caused functional problems to appear
(Rafael Wysocki).
- Fix a device enumeration problem introduced in the 4.8 time frame
which caused the ACPI docking station driver to report incorrect
status via sysfs among other things (Rafael Wysocki)"
* tag 'acpi-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Resources: Not a valid resource if buffer length too long"
ACPI / scan: Set the visited flag for all enumerated devices
Merge tag 'devmem-v4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CONFIG_STRICT_DEVMEM fix from Kees Cook:
"Fixes /dev/mem to read back zeros for System RAM areas in the 1MB
exception area on x86 to avoid exposing RAM or tripping hardened
usercopy"
* tag 'devmem-v4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
mm: Tighten x86 /dev/mem with zeroing reads
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael S. Tsirkin:
"virtio oops fixes
The virtio pci rework using shared interrupts caused a lot of issues.
We tried to fix them but run out of time. Revert for now, and revisit
the issue for the next kernel.
Luckily we are able to do this without loosing automatic interrupt
NUMA affinity which was the main motivator for the rework"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: Remove affinity hint before freeing the interrupt
Revert "virtio_pci: remove struct virtio_pci_vq_info"
Revert "virtio_pci: use shared interrupts for virtqueues"
Revert "virtio_pci: don't duplicate the msix_enable flag in struct pci_dev"
Revert "virtio_pci: simplify MSI-X setup"
Revert "virtio_pci: fix out of bound access for msix_names"
MAINTAINERS: fix virtio file pattern
virtio_console: fix uninitialized variable use
virtio_net: clear MTU when out of range
virtio: allow drivers to validate features
virtio_net: enable big packets for large MTU values
Aaro Koskinen [Fri, 14 Apr 2017 11:38:32 +0000 (13:38 +0200)]
fbdev: omapfb: delete check_required_callbacks()
Commit 561eb9d09a93 ("fbdev: omap/lcd: Make callbacks optional") made
panel callbacks optional but forgot to update check_required_callbacks().
As a result many (all?) OMAP systems using omapfb will crash at boot.
Fix by deleting the whole function.
Fixes: 561eb9d09a93 ("fbdev: omap/lcd: Make callbacks optional") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Merge branches 'pm-cpufreq-fixes' and 'pm-tools-fixes'
* pm-cpufreq-fixes:
cpufreq: Bring CPUs up even if cpufreq_online() failed
* pm-tools-fixes:
cpupower: Fix turbo frequency reporting for pre-Sandy Bridge cores
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
The presence of 'thp: reduce indentation level in change_huge_pmd()'
is unfortunate. But the patchset had been decently reviewed and tested
before we decided it was needed in -stable and I felt it best not to
churn things at the last minute"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mailmap: add Martin Kepplinger's email
zsmalloc: expand class bit
zram: do not use copy_page with non-page aligned address
zram: fix operator precedence to get offset
hugetlbfs: fix offset overflow in hugetlbfs mmap
thp: fix MADV_DONTNEED vs clear soft dirty race
thp: fix MADV_DONTNEED vs. MADV_FREE race
mm: drop unused pmdp_huge_get_and_clear_notify()
thp: fix MADV_DONTNEED vs. numa balancing race
thp: reduce indentation level in change_huge_pmd()
z3fold: fix page locking in z3fold_alloc()
Minchan Kim [Thu, 13 Apr 2017 21:56:40 +0000 (14:56 -0700)]
zsmalloc: expand class bit
Now 64K page system, zsamlloc has 257 classes so 8 class bit is not
enough. With that, it corrupts the system when zsmalloc stores
65536byte data(ie, index number 256) so that this patch increases class
bit for simple fix for stable backport. We should clean up this mess
soon.
Minchan Kim [Thu, 13 Apr 2017 21:56:37 +0000 (14:56 -0700)]
zram: do not use copy_page with non-page aligned address
The copy_page is optimized memcpy for page-alinged address. If it is
used with non-page aligned address, it can corrupt memory which means
system corruption. With zram, it can happen with
1. 64K architecture
2. partial IO
3. slub debug
Partial IO need to allocate a page and zram allocates it via kmalloc.
With slub debug, kmalloc(PAGE_SIZE) doesn't return page-size aligned
address. And finally, copy_page(mem, cmem) corrupts memory.
So, this patch changes it to memcpy.
Actuaully, we don't need to change zram_bvec_write part because zsmalloc
returns page-aligned address in case of PAGE_SIZE class but it's not
good to rely on the internal of zsmalloc.
Note:
When this patch is merged to stable, clear_page should be fixed, too.
Unfortunately, recent zram removes it by "same page merge" feature so
it's hard to backport this patch to -stable tree.
I will handle it when I receive the mail from stable tree maintainer to
merge this patch to backport.
Fixes: 42e99bd ("zram: optimize memory operations with clear_page()/copy_page()") Link: http://lkml.kernel.org/r/1492042622-12074-2-git-send-email-minchan@kernel.org Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Thu, 13 Apr 2017 21:56:35 +0000 (14:56 -0700)]
zram: fix operator precedence to get offset
In zram_rw_page, the logic to get offset is wrong by operator precedence
(i.e., "<<" is higher than "&"). With wrong offset, zram can corrupt
the user's data. This patch fixes it.
Fixes: 8c7f01025 ("zram: implement rw_page operation of zram") Link: http://lkml.kernel.org/r/1492042622-12074-1-git-send-email-minchan@kernel.org Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Thu, 13 Apr 2017 21:56:32 +0000 (14:56 -0700)]
hugetlbfs: fix offset overflow in hugetlbfs mmap
If mmap() maps a file, it can be passed an offset into the file at which
the mapping is to start. Offset could be a negative value when
represented as a loff_t. The offset plus length will be used to update
the file size (i_size) which is also a loff_t.
Validate the value of offset and offset + length to make sure they do
not overflow and appear as negative.
Found by syzcaller with commit ff8c0c53c475 ("mm/hugetlb.c: don't call
region_abort if region_chg fails") applied. Prior to this commit, the
overflow would still occur but we would luckily return ENOMEM.
Both MADV_DONTNEED and MADV_FREE handled with down_read(mmap_sem).
It's critical to not clear pmd intermittently while handling MADV_FREE
to avoid race with MADV_DONTNEED:
CPU0: CPU1:
madvise_free_huge_pmd()
pmdp_huge_get_and_clear_full()
madvise_dontneed()
zap_pmd_range()
pmd_trans_huge(*pmd) == 0 (without ptl)
// skip the pmd
set_pmd_at();
// pmd is re-established
It results in MADV_DONTNEED skipping the pmd, leaving it not cleared.
It violates MADV_DONTNEED interface and can result is userspace
misbehaviour.
Basically it's the same race as with numa balancing in
change_huge_pmd(), but a bit simpler to mitigate: we don't need to
preserve dirty/young flags here due to MADV_FREE functionality.
[kirill.shutemov@linux.intel.com: Urgh... Power is special again] Link: http://lkml.kernel.org/r/20170303102636.bhd2zhtpds4mt62a@black.fi.intel.com Link: http://lkml.kernel.org/r/20170302151034.27829-4-kirill.shutemov@linux.intel.com Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case prot_numa, we are under down_read(mmap_sem). It's critical to
not clear pmd intermittently to avoid race with MADV_DONTNEED which is
also under down_read(mmap_sem):
CPU0: CPU1:
change_huge_pmd(prot_numa=1)
pmdp_huge_get_and_clear_notify()
madvise_dontneed()
zap_pmd_range()
pmd_trans_huge(*pmd) == 0 (without ptl)
// skip the pmd
set_pmd_at();
// pmd is re-established
The race makes MADV_DONTNEED miss the huge pmd and don't clear it
which may break userspace.
Found by code analysis, never saw triggered.
Link: http://lkml.kernel.org/r/20170302151034.27829-3-kirill.shutemov@linux.intel.com Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stress testing of the current z3fold implementation on a 8-core system
revealed it was possible that a z3fold page deleted from its unbuddied
list in z3fold_alloc() would be put on another unbuddied list by
z3fold_free() while z3fold_alloc() is still processing it. This has
been introduced with commit 5a27aa822 ("z3fold: add kref refcounting")
due to the removal of special handling of a z3fold page not on any list
in z3fold_free().
To fix this, the z3fold page lock should be taken in z3fold_alloc()
before the pool lock is released. To avoid deadlocking, we just try to
lock the page as soon as we get a hold of it, and if trylock fails, we
drop this page and take the next one.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Cc: Dan Streetman <ddstreet@ieee.org> Cc: <Oleksiy.Avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log