Jingoo Han [Tue, 29 Oct 2013 06:12:34 +0000 (15:12 +0900)]
ARM: dts: use 'status' property for PCIe nodes
Set the default status for PCIe to disabled in the exynos5440.dtsi
file and let the board dts files such as exynos5440-ssdk5440.dts
enable the PCIe. However, keep the PCIe for SD5v1 board disabled,
because there is no PCIe slot on SD5v1 board.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 29 Oct 2013 19:41:43 +0000 (12:41 -0700)]
Merge branch 'sirf/dt' into next/dt
From Barry Song:
Some missed dt nodes for sirf dts for 3.13. Among them:
- add missed chhifbg node in prima2 and atlas6 dts
- add missed cell, cs and dma channel for SPI nodes
- add missed graphics2d iobg in atlas6 dts
- add missed address-cells and size-cells for prima2 I2C
- add missed memcontrol-monitor node in prima2 and atlas6 dts
* sirf/dt:
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
Olof Johansson [Mon, 28 Oct 2013 21:47:50 +0000 (14:47 -0700)]
Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Olof Johansson [Mon, 28 Oct 2013 21:43:09 +0000 (14:43 -0700)]
Merge tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Few patches to make cpufreq work for omap3 with device tree.
Note that this branch has a dependency to the patches merged
with omap-for-v3.13/board-removal-signed-take2.
* tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: use cpu0-cpufreq driver in device tree supported boot
ARM: OMAP2+: add missing lateinit hook for calling pm late init
ARM: OMAP3+: do not register non-dt OPP tables for device tree boot
* tag 'dt-3.13-4' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add the core-divider clock to Armada 370/XP
ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
ARM: mvebu: Add Core Divider clock device-tree binding
Olof Johansson [Mon, 28 Oct 2013 20:21:42 +0000 (13:21 -0700)]
Merge tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
The imx/mxs device tree changes for 3.13:
- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree
* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
ARM: dts: imx6sl-evk: enable the SPI NOR
ARM: dts: imx6sl: add a pinctrl for ECSPI1
ARM: imx27: add missing #pwm-cells property
ARM: dts: imx6sl: add pinctrl uhs states for usdhc
ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
ARM: imx27-apf27dev: Add framebuffer support
ARM: imx51-apf51dev: Add parallel display support
ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
ARM: dts: mxs: Add MSR M28CU3 board
ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
ARM: dts: imx6qdl: add pcie device node
ARM: dts: imx6q-udoo: Add initial board support
ARM: dts: mxs: Add muxing options for the SSP2 MMC
ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
...
Olof Johansson [Mon, 28 Oct 2013 04:54:02 +0000 (21:54 -0700)]
Merge most of tag 'tags/exynos-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git into next/dt
From Kukjin Kim, these are device-tree updates for Exynos. Among the changes:
- add MIPI PHY node for exynos4
- update regulator for origen and exynos5250-arndale
- add support HDMI for exynos5250, exynos5420
* commit '93457b9cb980ffeeef020c3bcd99065c3807619b':
ARM: dts: Add HDMI related I2C nodes for Arndale board
ARM: dts: enable hdmi subsystem for exynos5420 smdk board
ARM: dts: add dt nodes for hdmi subsystem for exynos5420
ARM: dts: add i2c device nodes for Exynos5420
ARM: dts: add clocks to hdmi dt node for exynos5250
ARM: dts: add mixer clocks to mixer node for Exynos5250
of/documentation: update with clock information for exynos hdmi subsystem
ARM: dts: Disable Exynos5250 I2S controllers by default
ARM: dts: Add reg property to regulator nodes in exynos5250-arndale
ARM: dts: Add fixed voltage regulator to simple bus for origen
ARM: dts: Add MIPI PHY node to exynos4.dtsi
Olof Johansson [Mon, 28 Oct 2013 04:19:54 +0000 (21:19 -0700)]
Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.
* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: register all SSP and SPI blocks
ARM: ux500: fix I2C4 clock bit
ARM: ux500: fix clock for GPIO blocks 6 and 7
clk: ux500: fix erroneous bit assignment
ARM: ux500: fix clock for GPIO block 8
Olof Johansson [Mon, 28 Oct 2013 04:14:40 +0000 (21:14 -0700)]
Merge tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner sunXi SoCs device tree changes for 3.13
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
* tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux:
ARM: sunxi: dts: Add support for the cubieboard3, the CubieTruck
ARM: sun7i: olinuxino-micro: Enable the I2C controllers
ARM: sun7i: cubieboard2: Enable the I2C controllers
ARM: sun7i: Add the pin muxing options for the I2C controllers
ARM: sun7i: Enable the I2C controllers
ARM: sunxi: dt: Add sunxi-sid to dts for sun4i, sun5i and sun7i
Ezequiel Garcia [Fri, 18 Oct 2013 23:02:30 +0000 (20:02 -0300)]
ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
Armada 370/XP SoCs have a 2 GHz fixed PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Peter Ujfalusi [Wed, 23 Oct 2013 09:32:20 +0000 (12:32 +0300)]
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
J Keerthy [Wed, 16 Oct 2013 15:39:07 +0000 (10:39 -0500)]
ARM: dts: DRA7: Add CPU OPP table
Add DT OPP table for DRA7xx family of devices. This data is decoded by
OF with of_init_opp_table() helper function.
The data is based on DRA75x, DRA74x Data Manual revision F (Sept 2013).
TODO: add OPP_HIGH after AVS-Class0 is functional
NOTE: The voltage and frequency values work well only on NOM samples
and it is mandatory to use ABB/AVS Class 0 support for all OPPs.
Clock nodes are pending clock node alignment.
[nm@ti.com: cleanups and rebase to latest] Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: J Keerthy <j-keerthy@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
J Keerthy [Wed, 16 Oct 2013 15:39:06 +0000 (10:39 -0500)]
ARM: dts: OMAP5: Add CPU OPP table
Add DT OPP table for OMAP54xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
The data is based on OMAP543x ES2.0 DM Operating Condition Addendum
Version 0.6(April 2013)
NOTE: The voltage and frequency values work well only on NOM samples
and are supposed to work properly only with ABB/AVS for ALL OPPs.
TODO: Add SPEED BIN OPP after ABB and AVS support so the cpufreq works
on all samples seamlessly. Clock node is pending alignment for clock
dts conversion
[nm@ti.com: sync to latest and fixes] Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: J Keerthy <j-keerthy@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Nishanth Menon [Wed, 16 Oct 2013 15:39:03 +0000 (10:39 -0500)]
ARM: OMAP3+: use cpu0-cpufreq driver in device tree supported boot
With OMAP3+ and AM33xx supported SoC having defined CPU device tree
entries with operating-points and clock nodes defined, we can now use
the SoC generic cpufreq-cpu0 driver by registering appropriate device.
Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Wed, 16 Oct 2013 15:39:02 +0000 (10:39 -0500)]
ARM: OMAP2+: add missing lateinit hook for calling pm late init
AM335x, AM43xx, OMAP5 and DRA7 have missing late init hook. Introduce
SoC specific hook with a call to OMAP2+ generic lateinit hook. This
allows the generic late initializations such as cpufreq hooks to be
active.
Based on out-of-tree patches that need to be introduced in
mainline, this introduction allows us to provide the foundation for
further SoC specific features as they are developed.
Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Wed, 16 Oct 2013 15:39:01 +0000 (10:39 -0500)]
ARM: OMAP3+: do not register non-dt OPP tables for device tree boot
OMAP3+ supports both device tree and non-device tree boot.
Device tree bindings for OMAP3+ is supposed to be added via dts following:
Documentation/devicetree/bindings/power/opp.txt
Since we now have device tree entries for OMAP3+ cpu OPPs,
The current code wrongly adds duplicate OPPs. So, dont register OPPs
when booting using device tree.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Tony Lindgren [Thu, 17 Oct 2013 22:15:22 +0000 (15:15 -0700)]
ARM: dts: Add missing reg, interrupt and dma entries for omap3
Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: Benoit Cousson <bcousson@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Wed, 16 Oct 2013 20:21:03 +0000 (15:21 -0500)]
ARM: dts: OMAP3+: Add i2c aliases
Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.
Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Peter Ujfalusi [Sun, 20 Oct 2013 17:04:11 +0000 (20:04 +0300)]
ARM: dts: am335x-evmsk: Audio support
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Jyri Sarha [Sun, 20 Oct 2013 17:04:09 +0000 (20:04 +0300)]
ARM: dts: AM33XX: mcasp: Add location for data port registers to reg-property
This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
George Cherian [Thu, 10 Oct 2013 10:49:54 +0000 (16:19 +0530)]
ARM: dts: OMAP5: Add dr_mode for dwc3
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Nishanth Menon [Thu, 10 Oct 2013 16:44:41 +0000 (11:44 -0500)]
ARM: dts: omap4-panda-es: Do not reset gpio1
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Rajendra Nayak [Tue, 15 Oct 2013 07:07:50 +0000 (12:37 +0530)]
ARM: dts: omap: Add reset/idle on init bindings for OMAP
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Sricharan R [Thu, 10 Oct 2013 07:50:13 +0000 (13:20 +0530)]
ARM: dts: OMAP5: Remove clock-frequency field for cpu timers
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
Olof Johansson [Sat, 19 Oct 2013 00:30:19 +0000 (17:30 -0700)]
Merge tag 'omap-for-v3.13/pinctrl-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Looks like I managed to break the x86 build for some
configs. Here's a fix for that on top of the pinctrl
changes already merged with the signed tag
omap-for-v3.13/quirk-signed.
* tag 'omap-for-v3.13/pinctrl-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
pinctrl: single: Fix build when not built on ARM
Tony Lindgren [Fri, 18 Oct 2013 23:20:05 +0000 (16:20 -0700)]
pinctrl: single: Fix build when not built on ARM
Looks like we need a little bit of arch specific handling
with the generic IRQ. Fix the issue with an ifdef the
same way as other drivers do.
ARM needs things set to IRQF_VALID, which also then sets
noprobe. Others seem to use just irq_set_noprobe().
Otherwise we can get:
drivers/pinctrl/pinctrl-single.c: In function 'pcs_irqdomain_map':
drivers/pinctrl/pinctrl-single.c:1750:2: error: implicit declaration of function 'set_irq_flags' [-Werror=implicit-function-declaration]
drivers/pinctrl/pinctrl-single.c:1750:21: error: 'IRQF_VALID' undeclared (first use in this function)
drivers/pinctrl/pinctrl-single.c:1750:34: error: 'IRQF_PROBE' undeclared (first use in this function)
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman [Fri, 18 Oct 2013 18:30:16 +0000 (11:30 -0700)]
Merge tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
ARM: OMAP2+: remove legacy support for IGEP boards
Device Tree support for IGEP boards in mainline is almost
finished. The only remaining bits are support for the
Marvell SD8686 wifi + BT and TFP410 DVI chips.
Adding support for these should be straightforward so let's
not block OMAP3 moving to Device Tree only boot and remove
the board file for IGEP boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 14 Oct 2013 18:31:44 +0000 (11:31 -0700)]
ARM: OMAP2+: Remove legacy support for zoom platforms
We now have pretty decent device tree based support for
zoom platforms. It's not complete, but basics work for
me so adding more features should be quite trivial.
Looks like also 3630 sdp is zoom based, and looking
at it's board file should also be trivial to support
with the device tree based booting.
Patches are welcome if people are still using these.
Aaro Koskinen [Tue, 15 Oct 2013 20:36:09 +0000 (23:36 +0300)]
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 14 Oct 2013 18:31:43 +0000 (11:31 -0700)]
ARM: dts: Add basic support for zoom3
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Kevin Hilman [Fri, 18 Oct 2013 15:21:17 +0000 (08:21 -0700)]
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT series for 3.13
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: remove pinctrl conflict between mmc and SPI for at91sam9g20ek
ARM: at91: add sound support on at91sam9n12ek board
ARM: at91: enable ssc on at91sam9n12ek board
ARM: at91: enable wm8904 on at91sam9n12ek board
ARM: at91: add ssc dma parameter for at91sam9n12
ARM: at91: add at91sam9n12 ssc clock in look up table
ARM: at91: remove pinctrl conflict between mmc and SPI for at91sam9g20ek
These MMC and SPI buses can't be configured at the same time because they
share the same traces on the EK board.
Reported-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Linus Walleij [Fri, 18 Oct 2013 08:39:58 +0000 (10:39 +0200)]
ARM: ux500: fix I2C4 clock bit
The PCLK for I2C4 is controlled by bit 10 in the PCKEN registers
while the KCLK is controlled by bit 9 on the KCKEN, it's
one of these odd assymetric things. Correct the PCLK bit to 10.
Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 18 Oct 2013 07:49:21 +0000 (09:49 +0200)]
ARM: ux500: fix clock for GPIO blocks 6 and 7
The clock assignment in the device tree for GPIO blocks 6
and 7 was incorrect, indicating this was managed by bit 1 on
PRCC 2 while it was in fact bit 11 on PRCC 2.
Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 18 Oct 2013 08:56:14 +0000 (10:56 +0200)]
clk: ux500: fix erroneous bit assignment
Due to a typo or similar, the peripheral group 2 clock 11
gate was set to bit 1 instead of bit 11. We need to fix this
to be able to set the correct enable bit in the device tree:
when trying to correct the bit assignment in the device tree,
the system would hang.
Cc: Mike Turquette <mturquette@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 18 Oct 2013 07:45:07 +0000 (09:45 +0200)]
ARM: ux500: fix clock for GPIO block 8
The clock assignment in the device tree for GPIO block 8 was
incorrect, indicating this was managed by bit 1 on PRCC 6
while it was in fact bit 1 on PRCC 5.
Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kevin Hilman [Thu, 17 Oct 2013 23:02:36 +0000 (16:02 -0700)]
Merge branch 'tegra/dt' into next/dt
From Stephen Warren:
* tegra/dt:
ARM: tegra: Use symbolic names for gr3d clocks
ARM: tegra: Mark Tegra30 display controller compatible with Tegra20
ARM: tegra: add GPIO controller to tegra124.dtsi
ARM: tegra: enable LP1 suspend mode for Venice2
ARM: tegra: enable Tegra RTC as default for Tegra124
ARM: tegra: add Venice2 board support
ARM: tegra: Add initial device tree for Tegra124
ARM: tegra: add vcc supply for nct1008 to Cardhu
ARM: tegra: add DT entry for nct1008 to Dalmore
ARM: tegra: use dt-binding header for key code
ARM: tegra: add palmas pincontrol to Dalmore device tree
Kevin Hilman [Thu, 17 Oct 2013 22:22:29 +0000 (15:22 -0700)]
Merge tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 3)
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
* tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu:
ARM: Dove: fix bad properties of the si5351 clkout2 used by Cubox audio
ARM: Dove: Add the audio device to the Cubox DT
ARM: Dove: Add the audio devices in DT
Thierry Reding [Tue, 15 Oct 2013 15:28:02 +0000 (17:28 +0200)]
ARM: tegra: Use symbolic names for gr3d clocks
Commit 05849c9381354be4bd4a2a878b5ecb12d375a1a0 (ARM: tegra30: convert
device tree files to use CLK defines) updated the Tegra30 device tree to
use symbolic clock names but forgot to update this node.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Kevin Hilman [Mon, 14 Oct 2013 22:34:59 +0000 (15:34 -0700)]
Merge tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
omap device tree related changes via Benoit Cousson <bcousson@baylibre.com>:
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
* tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (58 commits)
ARM: dts: dra7-evm: Add mmc2 node for eMMC support
ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
ARM: dts: omap3-igep0020: use standard constant for IRQ flags
ARM: dts: omap3-igep0020: Add HS USB Host support
ARM: dts: omap3-igep: Add USB OTG support
ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
ARM: dts: AM33XX: Add LCDC info into am335x-evm
ARM: dts: AM437X: Add DES node
ARM: dts: AM437X: Add AES node
ARM: dts: AM33XX: Fix AES interrupt number
ARM: dts: AM33XX: Add AES data and documentation
ARM: dts: AM33XX: Add SHAM data and documentation
ARM: dts: OMAP4: Add DES3DES node
ARM: dts: OMAP4: Add AES node
ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit mode
ARM: dts: am335x-bone-common: correct mux mode for cmd line
ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.
ARM: dts: AM33XX: Add support for IGEP COM AQUILA
ARM: dts: am335x-boneblack: move fixed regulator to board level
...
Kevin Hilman [Mon, 14 Oct 2013 22:29:10 +0000 (15:29 -0700)]
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Kevin Hilman [Mon, 14 Oct 2013 22:12:01 +0000 (15:12 -0700)]
Merge tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next into next/dt
From Dinh Nguyen:
Updates to dts file structure for Altera's SOCFPGA
* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
socfpga.dtsi
-> socfpga_$board.dts
-> socfpga_$otherboard.dts
to
socfpga.dtsi
-> socfpga_cyclone5.dtsi
--> socfpga_cyclone5_$board.dts
--> socfpga_cyclone5_$otherboard.dts
"
* tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next:
dts: socfpga: Add support for Altera's SOCFPGA Arria V board
ARM: socfpga: dts: fix s2f_* clock name
ARM: socfpga: dts: cleanup indentation
ARM: socfpga: dts: Add support for terasic SoCkit
ARM: socfpga: dts: Move common nodes to cyclone5 dtsi
arm: socfpga: Add clock for smp_twd timer
Kevin Hilman [Mon, 14 Oct 2013 20:52:59 +0000 (13:52 -0700)]
Merge branch 'renesas/dt2' into next/dt
From Simon Horman:
* renesas/dt2: (21 commits)
ARM: shmobile: bockw: fixup ether node naming
ARM: shmobile: r8a7779: add irqpin default status on DTSI
ARM: shmobile: marzen: fixup SMSC IRQ number on DTS
ARM: shmobile: bockw: add SMSC support on DTS
ARM: shmobile: r8a7778: add renesas_intc_irqpin support on DTSI
ARM: shmobile: r8a7791 SMP device tree node
ARM: shmobile: r8a7791 Arch timer device tree node
ARM: shmobile: r8a7791 IRQC device tree node
ARM: shmobile: armadillo800eva-reference: add SDHI and MMCIF interfaces
ARM: shmobile: armadillo-reference: Add PWM backlight node to DT
ARM: shmobile: r8a73a4: add a DT node for the DMAC
ARM: shmobile: r8a7790: add I2C DT nodes
ARM: shmobile: only enable used I2C interfaces in DT on all Renesas boards
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
...