Recent assembler versions complain about extraneous
whitespace inside [] brackets. This fixes all of
these instances for the samsung platforms. We should
backport this to all kernels that might need to
be built with new binutils.
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r2,[ r6,#(0x10)]'
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r0,[ r6,#(0x14)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r2,[ r6,#(0x10)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r0,[ r6,#(0x14)]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S: Assembler messages:
arch/arm/mach-s3c24xx/sleep-s3c2410.S:48: Error: ARM register expected -- `ldr r7,[ r4 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:49: Error: ARM register expected -- `ldr r8,[ r5 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:50: Error: ARM register expected -- `ldr r9,[ r6 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:64: Error: ARM register expected -- `streq r7,[ r4 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:65: Error: ARM register expected -- `streq r8,[ r5 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:66: Error: ARM register expected -- `streq r9,[ r6 ]'
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r2,#((0x0B0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-((0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r2,#((0x0B0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-((0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/mach-s3c24xx/pm-h1940.S: Assembler messages:
arch/arm/mach-s3c24xx/pm-h1940.S:33: Error: ARM register expected -- `ldr pc,[ r0,#((0x0B8)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000)))]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S: Assembler messages:
arch/arm/mach-s3c24xx/sleep-s3c2412.S:60: Error: ARM register expected -- `ldrne r9,[ r1 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:61: Error: ARM register expected -- `strne r9,[ r1 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:62: Error: ARM register expected -- `ldrne r9,[ r2 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:63: Error: ARM register expected -- `strne r9,[ r2 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:64: Error: ARM register expected -- `ldrne r9,[ r3 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:65: Error: ARM register expected -- `strne r9,[ r3 ]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x08)]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x10)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x08)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x10)]'
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the use of USART on both at91sam9x5 and at91sam9n12. In DTS, the
atmel,use-dma-[rx|tx] property is present but a DMA channel cannot be used.
Indeed the connexion between the DMA engine and the slave is not implemented
yet in Device Tree.
Note however that this property is also used for PDC (private DMA) on older
SoCs. This is why the driver alone cannot determine the validity of this
property.
Reported-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The PCI glue layer was using an hard-coded IRQ 27 offset.
This caused the immediate regression.
- The SIC IRQ mask was inverted (i.e. a bit was indeed set to
one for each valid IRQ on the SIC, but accidentally inverted
in the init call). This has been around forever, but we have
been saved by some other forgiving code that would reserve
IRQ descriptors in this range, as the versatile is
non-sparse.
When the IRQs were bumped up 32 steps so as to avoid using IRQ
zero and avoid touching the 16 legacy IRQs, things broke.
Introduce an explicit valid mask for the IRQs that are active
on the PIC/SIC, and pass that. Use the BIT() macro from
<linux/bitops.h> to make sure we hit the right bits, readily
defined in <mach/platform.h>.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously arizona_calc_fll() was checking if the target frequency is
exactly divisible by reference frequency, but should have been product
of the ratio and the reference frequency.
Also scale down the Lamba and Theta coefficients be under 16-bits in
order to match the registers.
Signed-off-by: Ryo Tsutsui <ryo.tsutsui@wolfsonmicro.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems the setting of the channel bits for particular scanning modes
was incorrect for differential mode. (Only half the number of channels
are available in differential mode; comedi refers to them as channels 0,
1, 2 and 3, but the hardware documentation refers to them as channels 0,
2, 4 and 6.) In differential mode, the setting of the channel enable
bits in the command1 register should depend on whether the scan enable
bit is set. Effectively, we need to double the comedi channel number
when the scan enable bit is not set in differential mode. The scan
enable bit gets set when the AI scan mode is `MODE_MULT_CHAN_UP` or
`MODE_MULT_CHAN_DOWN`, and gets cleared when the AI scan mode is
`MODE_SINGLE_CHAN` or `MODE_SINGLE_CHAN_INTERVAL`. The existing test
for whether the comedi channel number needs to be doubled in
differential mode is incorrect in `labpc_ai_cmd()`. This patch corrects
the test.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems that writing to the command3 register after writing to the
command4 register in `labpc_ai_cmd()` messes up the differential
reference bit setting in the command4 register. Set up the command4
register after the command3 register (as in `labpc_ai_rinsn()`) to avoid
the problem.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comedi has two sorts of minor devices:
(a) normal board minor devices in the range 0 to
COMEDI_NUM_BOARD_MINORS-1 inclusive; and
(b) special subdevice minor devices in the range COMEDI_NUM_BOARD_MINORS
upwards that are used to open the same underlying comedi device as the
normal board minor devices, but with non-default read and write
subdevices for asynchronous commands.
The special subdevice minor devices get created when a board supporting
asynchronous commands is attached to a normal board minor device, and
destroyed when the board is detached from the normal board minor device.
One way to attach or detach a board is by using the COMEDI_DEVCONFIG
ioctl. This should only be used on normal board minors as the special
subdevice minors are too ephemeral. In particular, the change
introduced in commit 7d3135af399e92cf4c9bbc5f86b6c140aab3b88c ("staging:
comedi: prevent auto-unconfig of manually configured devices") breaks
horribly for special subdevice minor devices.
Since there's no legitimate use for the COMEDI_DEVCONFIG ioctl on a
special subdevice minor device node, disallow it and return -ENOTTY.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, Matt Sealey reported he fail to build zsmalloc caused by
using of local_flush_tlb_kernel_range which are architecture dependent
function so !CONFIG_SMP in ARM couldn't implement it so it ends up
build error following as.
The reason we used that function is copy method by [1]
was really slow in ARM but at that time.
More severe problem is ARM can prefetch speculatively on other CPUs
so under us, other TLBs can have an entry only if we do flush local
CPU. Russell King pointed that. Thanks!
We don't have many choices except using flush_tlb_kernel_range.
My experiment in ARMv7 processor 4 core didn't make any difference with
zsmapbench[2] between local_flush_tlb_kernel_range and flush_tlb_kernel_range
but still page-table based is much better than copy-based.
This patch replace local_flush_tlb_kernel_range with
flush_tlb_kernel_range which are avaialbe in all architectures
because we already have used it in vmalloc allocator which are
generic one so build problem should go away and performane loss
shoud be void.
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56359 Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If encoder is switched off by BIOS, but the panel fitter is left on,
we never try to turn off the panel fitter and leave it still attached
to the pipe - which can cause blurry output elsewhere.
Based on work by Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58867 Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
[danvet: Remove the redundant HAS_PCH_SPLIT check and add a tiny
comment.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed the register write sequence for restoring the backlight, which
helped prevent non-working backlights on some machines. Turns out that
the original sequence was the right thing to do for a different set of
machines. Worse, setting the backlight level _after_ enabling it seems
to reset it somehow. So we need to make that one conditional upon the
backlight having been reset to zero, and add the old one back.
The RC6 VIDS has a linear ramp starting at 250mv, which means any values
below 250 are invalid. The old buggy macros tried to adjust for this to
be more flexible, but there is no need. As Dan pointed out the ENCODE
only ever has one value. The only invalid value for decode is an input
of 0 which means something is really wonky, and the cases where DECODE
are used either don't matter (debug values), or would be implicitly
correct (the check for less than 450).
This patch makes simpler, easier to read macros which are actually
correct. Maybe this patch can actually fix some bugs now.
Thanks to Dan for catching this. /me hides
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding the fb idle detection to mark-inactive, it was forgotten
that userspace can drive the processing of retire-requests. We assumed
that it would be principally driven by the retire requests worker,
running once every second whilst active and so we would get the deferred
timer for free. Instead we spend too many CPU cycles reclocking the LVDS
preventing real work from being done.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-and-tested-by: Alexander Lam <lambchop468@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58843 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.
We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.
There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's safe only under namespace_sem or vfsmount_lock; all places
in fs/namespace.c that want mnt->mnt_ns->user_ns actually want to use
current->nsproxy->mnt_ns->user_ns (note the calls of check_mnt() in
there).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While looking at plymouth on udl I noticed that plymouth was trying
to use its fb plugin not its drm one, it was trying to drmOpen a driver called
usb not udl, noticed that we actually had out driver pointing at the wrong
device.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk cause a regression, and it looks like the original bug was
simply a lack of FIFO bandwidth on the i915G of the reporter. Which
should eventually be fixed as soon as we get around to implemented
DSPARB FIFO reassignment on gen 3.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52281 Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bit 0 of the features byte (0x18) is set to 0, then, according to
the EDID spec, "the display is non-continuous frequency (multi-mode)
and is only specified to accept the video timing formats that are
listed in Base EDID and certain Extension Blocks".
For more information, please see the EDID spec, check the notes of the
table that explains the "Feature Support" byte (18h) and also the
notes on the tables of the section that explains "Display Range Limits
& Additional Timing Description Definition (tag #FDh)".
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we switch from 256->512 byte font rendering mode, it means the
current contents of the screen is being reinterpreted. The bit that holds
the high bit of the 9-bit font, may have been previously set, and thus
the new font misrenders.
The problem case we see is grub2 writes spaces with the bit set, so it
ends up with data like 0x820, which gets reinterpreted into 0x120 char
which the font translates into G with a circumflex. This flashes up on
screen at boot and is quite ugly.
A current side effect of this patch though is that any rendering on the
screen changes color to a slightly darker color, but at least the screen
no longer corrupts.
v2: as suggested by hpa, always clear the attribute space, whether we
are are going to or from 512 chars.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Okay you don't really want to use udl devices as your console, but if
you are unlucky enough to do so, you run into a lot of schedule while atomic
due to printk being called from all sorts of funky places. So check if we
are in an atomic context, and queue the damage for later, the next printk
should cause it to appear. This isn't ideal, but it is simple, and seems to
work okay in my testing here.
(dirty area idea came from xenfb)
fixes a bunch of sleeping while atomic issues running fbcon on udl devices.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only enable it when we disable the display rather than
at DPMS time since enabling it requires a full modeset
to restore the display state. Fixes blank screens in
certain cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we set the sun4u version of the PTE execute bit, it's:
or REG, _PAGE_EXEC_4U, REG
_PAGE_EXEC_4U is 0x1000, unfortunately the immedate field of the
'or' instruction is a signed 13-bit value. So the above actually
assembles into:
or REG, -4096, REG
completely corrupting the final PTE value.
Set it with a:
sethi %hi(_PAGE_EXEC_4U), TMP
or REG, TMP, REG
sequence instead.
This fixes "git gc" crashes on sun4u machines.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If our first THP installation for an MM is via the set_pmd_at() done
during khugepaged's collapsing we'll end up in tsb_grow() trying to do
a GFP_KERNEL allocation with several locks held.
Simply using GFP_ATOMIC in this situation is not the best option
because we really can't have this fail, so we'd really like to keep
this an order 0 GFP_KERNEL allocation if possible.
Also, doing the TSB allocation from khugepaged is a really bad idea
because we'll allocate it potentially from the wrong NUMA node in that
context.
So what we do is defer the hugepage TSB allocation until the first TLB
miss we take on a hugepage. This is slightly tricky because we have
to handle two unusual cases:
1) Taking the first hugepage TLB miss in the window trap handler.
We'll call the winfix_trampoline when that is detected.
2) An initial TSB allocation via TLB miss races with a hugetlb
fault on another cpu running the same MM. We handle this by
unconditionally loading the TSB we see into the current cpu
even if it's non-NULL at hugetlb_setup time.
Reported-by: Meelis Roos <mroos@ut.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accomodate the possibility that the TSB might be NULL at
the point that update_mmu_cache() is invoked. This is
necessary because we will sometimes need to defer the TSB
allocation to the first fault that happens in the 'mm'.
Seperate out the hugepage PTE test into a seperate function
so that the logic is clearer.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should "|= more_flags" rather than "= more_flags".
Reported-by: David Rientjes <rientjes@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allocates a block reservation structure before growing
or shrinking a file. Without this structure, the grow or shink code
can reference the bad pointer.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, eld_valid is never set to false, except at kernel module
load time. This patch makes sure that eld is no longer valid when
the cable is (hot-)unplugged.
The commit [dcda58061: ALSA: hda - Add workaround for conflicting
IEC958 controls] introduced a workaround for cards that have both
SPDIF and HDMI devices for giving device=1 to SPDIF control elements.
It turned out, however, that this workaround doesn't work well -
- The workaround checks only conflicts in a single codec, but SPDIF
and HDMI are provided by multiple codecs in many cases, and
- ALSA mixer abstraction doesn't care about the device number in ctl
elements, thus you'll get errors from amixer such as
% amixer scontrols -c 0
ALSA lib simple_none.c:1551:(simple_add1) helem (MIXER,'IEC958
Playback Switch',0,1,0) appears twice or more
amixer: Mixer hw:0 load error: Invalid argument
This patch fixes the previous broken workaround. Instead of changing
the device number of SPDIF ctl elements, shift the element indices of
such controls up to 16. Also, the conflict check is performed over
all codecs found on the bus.
HDMI devices will be put to dev=0,index=0 as before. Only the
conflicting SPDIF device is moved to a different place. The new place
of SPDIF device is supposed by the updated alsa-lib HDA-Intel.conf,
respectively.
Some Vaio all-in-one desktop PCs (for example VGC-LN51JGB) are affected by
the same issue that caused Vaio Z laptops to become silent: the speaker pin
must be connected to the first DAC even though the codec itself advertises
flexible routing through any of the DACs.
Use the no-primary-hp fixup for choosing the speaker pin as the primary so
that the right DAC is assigned on this device.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d45e6889ee69456a4d5b1bbb32252f460cd48fa9 ("ALSA: hda - Provide
the proper channel mapping for generic HDMI driver") added support for
custom channel maps in the HDA HDMI driver. Due to a mistake in an
'if' condition the custom map is always used even when no such map has
been set. This causes incorrect channel mapping for multichannel audio
by default.
Pass per_pin->chmap_set to hdmi_setup_channel_mapping() as a parameter
so that it can use it for detecting if a custom map has been set instead
of checking if map is NULL (which is never the case).
Commit 99fc86450c439039d2ef88d06b222fd51a779176 "ALSA: usb-mixer:
parse descriptors with structs" introduced a set of useful parsers
for descriptors. Unfortunately the parses for the Processing Unit
Descriptor came with a very subtle bug...
Functions uac_processing_unit_iProcessing() and
uac_processing_unit_specific() were indexing the baSourceID array
forgetting the fields before the iProcessing and process-specific
descriptors.
The problem was observed with Sound Blaster Extigy mixer,
where nNrModes in Up/Down-mix Processing Unit Descriptor
was accessed at offset 10 of the descriptor (value 0)
instead of offset 15 (value 7). In result the resulting
control had interesting limit values:
bootresponse in snd_usb_mbox2_boot_quirk is only 12 (decimal) u8's
long, but i9s passed to snd_usb_ctl_msg as it would be 0x12 (hexa)
long. Fix that by having proper size of the array, i.e. 0x12.
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The
device was tested in managed mode with no security, WEP 128
bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum: 7d676323ac60d6e1a3b6d61e8c528248). It works.
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl> Acked-By: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
layoutget's prepare hook can call rpc_exit with status = NFS4_OK (0).
Because of this, nfs4_proc_layoutget can't depend on a 0 status to mean
that the RPC was successfully sent, received and parsed.
To fix this, use the result's len member to see if parsing took place.
This fixes the following OOPS -- calling xdr_init_decode() with a buffer length
0 doesn't set the stream's 'p' member and ends up using uninitialized memory
in filelayout_decode_layout.
The current code in pnfs_destroy_all_layouts() assumes that removing
the layout from the server->layouts list is sufficient to make it
invisible to other processes. This ignores the fact that most
users access the layout through the nfs_inode->layout...
There is further breakage due to lack of reference counting of the
layouts, meaning that the whole thing Oopses at the drop of a hat.
The code in initiate_bulk_draining() is almost correct, and can be
used as a model for pnfs_destroy_all_layouts(), so move that
code to pnfs.c, and refactor the code to allow us to choose between
a single filesystem bulk recall, and a recall of all layouts.
Also note that initiate_bulk_draining() currently calls iput() while
holding locks. Fix that too.
Currently, nlmclnt_lock will break out of the for(;;) loop when
the reclaimer wakes up the blocking lock thread by setting
nlm_lck_denied_grace_period. This causes the lock request to fail
with an ENOLCK error.
The intention was always to ensure that we resend the lock request
after the grace period has expired.
now pnfs client uses block layout, maybe we can remove
blocklayoutdriver first. if we umount later,
it can cause oops in unset_pnfs_layoutdriver.
because nfss->pnfs_curr_ld->clear_layoutdriver is invalid.
One of the side effects of deferred probe is that some drivers which
used to be probed before initcalls completed are now happening slightly
later. This causes two problems.
- If a console driver gets deferred, then it may not be ready when
userspace starts. For example, if a uart depends on pinctrl, then the
uart will get deferred and /dev/console will not be available
- __init sections will be discarded before built-in drivers are probed.
Strictly speaking, __init functions should not be called in a drivers
__probe path, but there are a lot of drivers (console stuff again)
that do anyway. In the past it was perfectly safe to do so because all
built-in drivers got probed before the end of initcalls.
This patch fixes the problem by forcing the first pass of the deferred
list to complete at late_initcall time. This is late enough to catch the
drivers that are known to have the above issues.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob van der Heij reported the following (paraphrased) on private mail.
The scenario is that I want to avoid backups to fill up the page
cache and purge stuff that is more likely to be used again (this is
with s390x Linux on z/VM, so I don't give it as much memory that
we don't care anymore). So I have something with LD_PRELOAD that
intercepts the close() call (from tar, in this case) and issues
a posix_fadvise() just before closing the file.
This mostly works, except for small files (less than 14 pages)
that remains in page cache after the face.
Unfortunately Rob has not had a chance to test this exact patch but the
test program below should be reproducing the problem he described.
The issue is the per-cpu pagevecs for LRU additions. If the pages are
added by one CPU but fadvise() is called on another then the pages
remain resident as the invalidate_mapping_pages() only drains the local
pagevecs via its call to pagevec_release(). The user-visible effect is
that a program that uses fadvise() properly is not obeyed.
A possible fix for this is to put the necessary smarts into
invalidate_mapping_pages() to globally drain the LRU pagevecs if a
pagevec page could not be discarded. The downside with this is that an
inode cache shrink would send a global IPI and memory pressure
potentially causing global IPI storms is very undesirable.
Instead, this patch adds a check during fadvise(POSIX_FADV_DONTNEED) to
check if invalidate_mapping_pages() discarded all the requested pages.
If a subset of pages are discarded it drains the LRU pagevecs and tries
again. If the second attempt fails, it assumes it is due to the pages
being mapped, locked or dirty and does not care. With this patch, an
application using fadvise() correctly will be obeyed but there is a
downside that a malicious application can force the kernel to send
global IPIs and increase overhead.
If accepted, I would like this to be considered as a -stable candidate.
It's not an urgent issue but it's a system call that is not working as
advertised which is weak.
The following test program demonstrates the problem. It should never
report that pages are still resident but will without this patch. It
assumes that CPU 0 and 1 exist.
int main() {
int fd;
int pagesize = getpagesize();
ssize_t written = 0, expected;
char *buf;
unsigned char *vec;
int resident, i;
cpu_set_t set;
/* Prepare the mincore vec */
vec = malloc(FILESIZE_PAGES);
if (vec == NULL) {
printf("ENOMEM\n");
exit(EXIT_FAILURE);
}
/* Bind ourselves to CPU 0 */
CPU_ZERO(&set);
CPU_SET(0, &set);
if (sched_setaffinity(getpid(), sizeof(set), &set) == -1) {
perror("sched_setaffinity");
exit(EXIT_FAILURE);
}
/* open file, unlink and write buffer */
fd = open("fadvise-test-file", O_CREAT|O_EXCL|O_RDWR);
if (fd == -1) {
perror("open");
exit(EXIT_FAILURE);
}
unlink("fadvise-test-file");
while (written < expected) {
ssize_t this_write;
this_write = write(fd, buf + written, expected - written);
if (this_write == -1) {
perror("write");
exit(EXIT_FAILURE);
}
written += this_write;
}
free(buf);
/*
* Force ourselves to another CPU. If fadvise only flushes the local
* CPUs pagevecs then the fadvise will fail to discard all file pages
*/
CPU_ZERO(&set);
CPU_SET(1, &set);
if (sched_setaffinity(getpid(), sizeof(set), &set) == -1) {
perror("sched_setaffinity");
exit(EXIT_FAILURE);
}
/* sync and fadvise to discard the page cache */
fsync(fd);
if (posix_fadvise(fd, 0, expected, POSIX_FADV_DONTNEED) == -1) {
perror("posix_fadvise");
exit(EXIT_FAILURE);
}
/* map the file and use mincore to see which parts of it are resident */
buf = mmap(NULL, expected, PROT_READ, MAP_SHARED, fd, 0);
if (buf == NULL) {
perror("mmap");
exit(EXIT_FAILURE);
}
if (mincore(buf, expected, vec) == -1) {
perror("mincore");
exit(EXIT_FAILURE);
}
/* Check residency */
for (i = 0, resident = 0; i < FILESIZE_PAGES; i++) {
if (vec[i])
resident++;
}
if (resident != 0) {
printf("Nr unexpected pages resident: %d\n", resident);
exit(EXIT_FAILURE);
}
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Rob van der Heij <rvdheij@gmail.com> Tested-by: Rob van der Heij <rvdheij@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmpfs remount logic preserves filesystem mempolicy if the mpol=M
option is not specified in the remount request. A new policy can be
specified if mpol=M is given.
Before this patch remounting an mpol bound tmpfs without specifying
mpol= mount option in the remount request would set the filesystem's
mempolicy object to a freed mempolicy object.
To reproduce the problem boot a DEBUG_PAGEALLOC kernel and run:
# mkdir /tmp/x
# mount -t tmpfs -o size=100M,mpol=interleave nodev /tmp/x
Non-debug kernels will not crash immediately because referencing the
dangling mpol will not cause a fault. Instead the filesystem will
reference a freed mempolicy object, which will cause unpredictable
behavior.
The problem boils down to a dropped mpol reference below if
shmem_parse_options() does not allocate a new mpol:
A patch to fix some unreachable code in search_my_process_keyrings() got
applied twice by two different routes upstream as commits e67eab39bee2
and b010520ab3d2 (both "fix unreachable code").
Unfortunately, the second application removed something it shouldn't
have and this wasn't detected by GIT. This is due to the patch not
having sufficient lines of context to distinguish the two places of
application.
The effect of this is relatively minor: inside the kernel, the keyring
search routines may search multiple keyrings and then prioritise the
errors if no keys or negative keys are found in any of them. With the
extra deletion, the presence of a negative key in the thread keyring
(causing ENOKEY) is incorrectly overridden by an error searching the
process keyring.
So revert the second application of the patch.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found that bdev->bd_invalidated was left set once revalidate_disk()
is called, which results in page cache flush every time that device is
open.
Specifically, we found this problem in MD block device. Once we resize
a MD device, mdadm --monitor periodically flush all page cache for that
device every 60 or 1000 seconds when it opens the device.
This bug lies since at least 3.2.0 till the latest kernel(3.6.2). Patch
is attached.
immediately aborts with a -EINVAL return code. This is however a valid
parameter. This abort occurs only if unmount is the sole event
parameter. If other event parameters are supplied, then the unmount
event wait will work.
The problem was introduced by commit 44b350fc23e ("inotify: Fix mask
checks"). In that commit, it states:
The mask checks in inotify_update_existing_watch() and
inotify_new_watch() are useless because inotify_arg_to_mask()
sets FS_IN_IGNORED and FS_EVENT_ON_CHILD bits anyway.
But instead of removing the useless checks, it did this:
mask = inotify_arg_to_mask(arg);
- if (unlikely(!mask))
+ if (unlikely(!(mask & IN_ALL_EVENTS)))
return -EINVAL;
The problem is that IN_ALL_EVENTS doesn't include IN_UNMOUNT, and other
parts of the code keep IN_UNMOUNT separate from IN_ALL_EVENTS. So the
check should be:
if (unlikely(!(mask & (IN_ALL_EVENTS | IN_UNMOUNT))))
But inotify_arg_to_mask(arg) always sets the IN_UNMOUNT bit in the mask
anyway, so the check is always going to pass and thus should simply be
removed. Also note that inotify_arg_to_mask completely controls what
mask bits get set from arg, there's no way for invalid bits to get
enabled there.
Lets fix it by simply removing the useless broken checks.
Signed-off-by: Jim Somerville <Jim.Somerville@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_robust_list() is in use and a removal would break existing user
space. With the permission checks in place it's not longer a security
hole. Remove the deprecation warnings.
On store status we need to copy the current state of registers
into a save area. Currently we might save stale versions:
The sie state descriptor doesnt have fields for guest ACRS,FPRS,
those registers are simply stored in the host registers. The host
program must copy these away if needed. We do that in vcpu_put/load.
If we now do a store status in KVM code between vcpu_put/load, the
saved values are not up-to-date. Lets collect the ACRS/FPRS before
saving them.
This also fixes some strange problems with hotplug and virtio-ccw,
since the low level machine check handler (on hotplug a machine check
will happen) will revalidate all registers with the content of the
save area.
Running under a kvm host does not necessarily imply the presence of
a page mapped above the main memory with the virtio information;
however, the code includes a hard coded access to that page.
Instead, check for the presence of the page and exit gracefully
before we hit an addressing exception if it does not exist.
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result of a
filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
Additionally, the list traversal in __mmu_notifier_release() is not
protected by the by the mmu_notifier_mm->hlist_lock which can result in
callouts to the ->release() notifier from both mmu_notifier_unregister()
and __mmu_notifier_release().
-stable suggestions:
The stable trees prior to 3.7.y need commits 21a92735f660 and 70400303ce0c cherry-picked in that order prior to cherry-picking this
commit. The 3.7.y tree already has those two commits.
Signed-off-by: Robin Holt <holt@sgi.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Avi Kivity <avi@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Sagi Grimberg <sagig@mellanox.co.il> Cc: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Remove the cdev from the system (with cdev_del) *before* deallocating it
(in pps_device_destruct, called via kobject_put from device_destroy).
Also prevent deallocating a device with open file handles.
A better long-term fix is probably to remove the cdev from the pps_device
entirely, and instead have all devices reference one global cdev. Then
the deallocation ordering becomes simpler.
But that's more complex and invasive change, so we leave that
for later.
Now that N_TTY uses tty->disc_data for its private data,
'subclass' ldiscs cannot use ->disc_data for their own private data.
(This is a regression is v3.8-rc1)
Use pps_lookup_dev to associate the tty with the pps source instead.
The PPS serial line discipline wants to attach a PPS device to a tty
without changing the tty code to add a struct pps_device * pointer.
Since the number of PPS devices in a typical system is generally very low
(n=1 is by far the most common), it's practical to search the entire list
of allocated pps devices. (We capture the timestamp before the lookup,
so the timing isn't affected.)
It is a bit ugly that this function, which is part of the in-kernel
PPS API, has to be in pps.c as opposed to kapi,c, but that's not
something that affects users.
There is a loophole between Xen's current implementation of
pv-spinlocks and the scheduler. This was triggerable through
a testcase until v3.6 changed the TLB flushing code. The
problem potentially is still there just not observable in the
same way.
What could happen was (is):
1. CPU n tries to schedule task x away and goes into a slow
wait for the runq lock of CPU n-# (must be one with a lower
number).
2. CPU n-#, while processing softirqs, tries to balance domains
and goes into a slow wait for its own runq lock (for updating
some records). Since this is a spin_lock_irqsave in softirq
context, interrupts will be re-enabled for the duration of
the poll_irq hypercall used by Xen.
3. Before the runq lock of CPU n-# is unlocked, CPU n-1 receives
an interrupt (e.g. endio) and when processing the interrupt,
tries to wake up task x. But that is in schedule and still
on_cpu, so try_to_wake_up goes into a tight loop.
4. The runq lock of CPU n-# gets unlocked, but the message only
gets sent to the first waiter, which is CPU n-# and that is
busily stuck.
5. CPU n-# never returns from the nested interruption to take and
release the lock because the scheduler uses a busy wait.
And CPU n never finishes the task migration because the unlock
notification only went to CPU n-#.
To avoid this and since the unlocking code has no real sense of
which waiter is best suited to grab the lock, just send the IPI
to all of them. This causes the waiters to return from the hyper-
call (those not interrupted at least) and do active spinlocking.
BugLink: http://bugs.launchpad.net/bugs/1011792 Acked-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 81732c3b2fed ("tty vt: Fix line garbage in virtual console on
command line edition") broke insert_char() in multiple ways. Then
commit b1a925f44a3a ("tty vt: Fix a regression in command line edition")
partially fixed it. However, the buffer being moved is still too large
and overflowing beyond the end of the current line, corrupting existing
characters on the next line.
Example test case:
echo -e "abc\nde\x1b[A\x1b[4h \x1b[4l\x1b[B"
Expected result:
ab c
de
Current result:
ab c
e
Needless to say that this is very annoying when inserting words in the
middle of paragraphs with certain text editors.
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-and-tested-by: Thomas Rosenkrantz <tom.rosary@googlemail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi
BUGS with a NULL pointer dereference because the per-driver configuration
data is not available. The probe function has been restructured as
suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Bastian Bittorf <bittorf@bluebottle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe
on SMP) introduced a recursive locking bug in imx_console_write().
The callchain is:
imx_rxint()
spin_lock_irqsave(&sport->port.lock,flags);
...
uart_handle_sysrq_char();
sysrq_function();
printk();
imx_console_write();
spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD
The bad news is that the kernel debugging facilities can dectect the
problem, but the printks never surface on the serial console for
obvious reasons.
There is a similar issue with oops_in_progress. If the kernel crashes
we really don't want to be stuck on the lock and unable to tell what
happened.
In general most UP originated drivers miss these checks and nobody
ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by
a large number of developers.
The solution is to avoid locking in the sysrq case and trylock in the
oops_in_progress case.
This scheme is used in other drivers as well and it would be nice if
we could move this to a common place, so the usual copy/paste/modify
bugs can be avoided.
Now there is another issue with this scheme:
CPU0 CPU1
printk()
rxint()
sysrq_detection() -> sets port->sysrq
return from interrupt
console_write()
if (port->sysrq)
avoid locking
port->sysrq is reset with the next receive character. So as long as
the port->sysrq is not reset and this can take an endless amount of
time if after the break no futher receive character follows, all
console writes happen unlocked.
While the current writer is protected against other console writers by
the console sem, it's unprotected against open/close or other
operations which fiddle with the port. That's what the above mentioned
commit tried to solve.
That's an issue in all drivers which use that scheme and unfortunately
there is no easy workaround. The only solution is to have a separate
indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to
smp_processor_id() before calling into handle_sysrq() and resets it to
-1 after that. Then change the locking check to:
if (port->sysrq_cpu == smp_processor_id())
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(port->lock, flags);
else
spin_lock_irqsave(port->lock, flags);
That would force all other cpus into the spin_lock path. Problem
solved, but that's way beyond the scope of this fix and really wants
to be implemented in a common function which calls the uart specific
write function to avoid another gazillion of hard to debug
copy/paste/modify bugs.
Reported-and-tested-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.
Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).
Note that the problem has been made more acute with commit 0998d0631001
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a deadlock when the multiplexer is closed while there
are still client side ports open.
When the multiplexer is closed and there are active tty's it tries to
close them with tty_vhangup. This has a problem though, because
tty_vhangup needs the tty_lock. This patch changes it to unlock the
tty_lock before attempting the hangup and relocks afterwards. The
additional call to tty_port_tty_set is needed because otherwise the
port stays active because of the reference counter.
This change also exposed another problem that other code paths don't
expect that the multiplexer could have been closed. This patch also adds
checks for these cases in the gsmtty_ class of function that could be
called.
The documentation explicitly states that "first close all virtual ports
before closing the physical port" but we've found this to not always
reality in our field situations. The GPRS / UTMS modem sometimes crashes
and needs a power cycle in that case which means cleanly shutting down
everything is not always possible. This change makes it much more robust
for our situation where at least the system is recoverable with this patch
and doesn't hang in a deadlock situation inside the kernel.
The patch is against the long term support kernel (3.4.27) and should
apply cleanly to more recent branches. Tested with a Telit GE864-QUADV2
and Telit HE910 modem.
snd-aloop driver has no proper PM implementation, thus the PM resume
may trigger Oops due to leftover timer instance. This patch adds the
missing suspend/resume implementation.
According to the other code in this driver and similar
code in rme96 it seems, that spin_lock_irq in
snd_rme32_capture_close function should be paired
with spin_unlock_irq.
Found by Linux Driver Verification project (linuxtesting.org).
commit d8e794dfd51c368ed3f686b7f4172830b60ae47b ("workqueue: set
delayed_work->timer function on initialization") exports function
delayed_work_timer_fn() only for GPL modules. This makes delayed-works
unusable for non-GPL modules, because initialization macro now requires
GPL symbol. For example schedule_delayed_work() available for non-GPL.
Enable hyperv_clocksource only if its advertised as a feature.
XenServer 6 returns the signature which is checked in
ms_hyperv_platform(), but it does not offer all features. Currently the
clocksource is enabled unconditionally in ms_hyperv_init_platform(), and
the result is a hanging guest.
Hyper-V spec Bit 1 indicates the availability of Partition Reference
Counter. Register the clocksource only if this bit is set.
The guest in question prints this in dmesg:
[ 0.000000] Hypervisor detected: Microsoft HyperV
[ 0.000000] HyperV: features 0x70, hints 0x0
This bug can be reproduced easily be setting 'viridian=1' in a HVM domU
.cfg file. A workaround without this patch is to boot the HVM guest with
'clocksource=jiffies'.
hrtimer_enqueue_reprogram contains a race which could result in
timer.base switch during unlock/lock sequence.
hrtimer_enqueue_reprogram is releasing the lock protecting the timer
base for calling raise_softirq_irqsoff() due to a lock ordering issue
versus rq->lock.
If during that time another CPU calls __hrtimer_start_range_ns() on
the same hrtimer, the timer base might switch, before the current CPU
can lock base->lock again and therefor the unlock_timer_base() call
will unlock the wrong lock.
[ tglx: Added comment and massaged changelog ]
Signed-off-by: Leonid Shatz <leonid.shatz@ravellosystems.com> Signed-off-by: Izik Eidus <izik.eidus@ravellosystems.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Link: http://lkml.kernel.org/r/1359981217-389-1-git-send-email-izik.eidus@ravellosystems.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trinity fuzzer triggered a task_struct reference leak via
clock_nanosleep with CPU_TIMERs. do_cpu_nanosleep() calls
posic_cpu_timer_create(), but misses a corresponding
posix_cpu_timer_del() which leads to the task_struct reference leak.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Cc: Dave Jones <davej@redhat.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Oleg Nesterov <oleg@redhat.com> Link: http://lkml.kernel.org/r/20130215100810.GF4392@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52553ddf(genirq: fix regression in irqfixup, irqpoll)
introduced a potential deadlock by calling the action handler with the
irq descriptor lock held.
Remove the call and let the handling code run even for an interrupt
where only a single action is registered. That matches the goal of
the above commit and avoids the deadlock.
Document the confusing action = desc->action reload in the handling
loop while at it.
defined(@array) is deprecated in Perl and gives off a warning.
Restructure the code to remove that warning.
[ hpa: it would be interesting to revert to the timeconst.bc script.
It appears that the failures reported by akpm during testing of
that script was due to a known broken version of make, not a problem
with bc. The Makefile rules could probably be restructured to avoid
the make bug, or it is probably old enough that it doesn't matter. ]
Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log