[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
The commit 3b4c34aac7abea4754059084d0eef667a1993ac8
"s5p-fimc: Add support for VIDIOC_PREPARE_BUF/CREATE_BUFS ioctls"
added a handler for VIDIOC_CREATE_BUFS ioctl, but the queue_setup
callback wasn't updated to properly interpret the pixel format.
In this situation memory corruption may happen with VIDIOC_CREATE_BUFS
ioctl. Update the queue_setup op to fix this.
[media] s5p-fimc: Fix locking in subdev set_crop op
When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.
Dan Carpenter [Sun, 22 Apr 2012 07:06:17 +0000 (04:06 -0300)]
[media] fintek-cir: change || to &&
The current condition is always true, so everything uses
LOGICAL_DEV_CIR_REV2 (8). It should be that Fintek products
0x0408(F71809) and 0x0804(F71855) use logical device
LOGICAL_DEV_CIR_REV1 (5) and other chip ids use logical device 8.
In other words, this fixes hardware detection for 0x0408 and 0x0804.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jarod Wilson <jarod@redhat.com> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
These controls have been marked for long time as V4L2_CID_HCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED in the DocBook and are going to be removed
from include/linux/videodev2.h.
Luis Henriques [Sat, 21 Apr 2012 15:25:21 +0000 (12:25 -0300)]
[media] rc: Postpone ISR registration
An early registration of an ISR was causing a crash to several users (for
example, with the ite-cir driver: http://bugs.launchpad.net/bugs/972723).
The reason was that IRQs were being triggered before a driver
initialisation was completed.
This patch fixes this by moving the invocation to request_irq() and to
request_region() to a later stage on the driver probe function.
Cc: <stable@vger.kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 20 Apr 2012 15:22:50 +0000 (12:22 -0300)]
[media] marvell-cam: fix an ARM build error
One of the OLPC changes lost a little in its translation to mainline,
leading to build errors on the ARM architecture. Remove the offending
line, and all will be well.
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
If multiple clients are registered on a single camera host interface,
the user-space hot-plug software can try to access the one, that probed
first, before probing of the second one has completed. This can be
handled by individual host drivers, but it is even better to hold back
the user-space until all the probing on this host has completed. This
fixes a race on ecovec with two clients registered on the CEU1 host, which
otherwise triggers a BUG() in sh_mobile_ceu_remove_device().
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
If sanity check fails in scu_command(), goto error leads to unlock of
an unheld mutex. The check should not fail in reality, but it nevertheless
worth fixing.
Found by Linux Driver Verification project (linuxtesting.org).
[media] dvb_frontend: Fix a regression when switching back to DVB-S
There are some softwares (Kaffeine and likely xine) that uses a
DVBv5 call to switch to DVB-S2, but expects that a DVBv3 call to
switch back to DVB-S. Well, this is not right, as a DVBv3 call
doesn't know anything about delivery systems.
However, as, by accident, this used to work, we need to restore its
behavior, in order to avoid regressions with those softwares.
Reported on this Fedora 16 bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=812895
Reported-by: Dieter Roever <Dieter.Roever@gmx.de> Cc: stable@kernel.org # for version 3.3 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Tue, 27 Mar 2012 08:51:00 +0000 (05:51 -0300)]
[media] uvcvideo: Fix race-related crash in uvc_video_clock_update()
The driver frees the clock samples buffer before stopping the video
buffers queue. If a DQBUF call arrives in-between,
uvc_video_clock_update() will be called with a NULL clock samples
buffer, leading to a crash. This occurs very frequently when using the
webcam with the flash browser plugin.
Move clock initialization/cleanup to uvc_video_enable() in order to free
the clock samples buffer after the queue is stopped. Make sure the clock
is reset at resume time to avoid miscalculating timestamps.
Hans Verkuil [Sun, 1 Apr 2012 18:24:48 +0000 (15:24 -0300)]
[media] Drivers/media/radio: Fix build error
On Sunday, April 01, 2012 21:09:34 Tracey Dent wrote:
> radio-maxiradio depends on SND_FM801_TEA575X_BOOL to build or will
> result in an build error such as:
>
> Kernel: arch/x86/boot/bzImage is ready (#1)
> ERROR: "snd_tea575x_init" [drivers/media/radio/radio-maxiradio.ko] undefined!
> ERROR: "snd_tea575x_exit" [drivers/media/radio/radio-maxiradio.ko] undefined!
> WARNING: modpost: Found 6 section mismatch(es).
> To see full details build your kernel with:
> 'make CONFIG_DEBUG_SECTION_MISMATCH=y'
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Select CONFIG_SND_TEA575X to fixes problem and enable
> the driver to be built as desired.
>
> v2:
> instead of selecting CONFIG_SND_FM801_TEA575X_BOOL, select
> CONFIG_SND_TEA575X, which in turns selects CONFIG_SND_FM801_TEA575X_BOOL
> and any other dependencies for it to build.
No, this is the correct patch:
RADIO_MAXIRADIO should be treated just like RADIO_SF16FMR2, I just didn't
realize at the time that it had to be added as a SND_TEA575X dependency.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Shea Levy <shea@shealevy.com> Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Rankin [Fri, 6 Apr 2012 21:38:18 +0000 (18:38 -0300)]
[media] dvb_frontend: regression fix: userspace ABI broken for xine
The commit e399ce77e6e has broken the DVB ABI for xine:
The problem is that xine is expecting every event after a successful
FE_SET_FRONTEND ioctl to have a non-zero frequency parameter, regardless
of whether the tuning process has LOCKed yet. What used to happen is
that the events inherited the initial tuning parameters from the
FE_SET_FRONTEND call. However, the fepriv->parameters_out struct is now
not initialised until the status contains the FE_HAS_LOCK bit.
You might argue that this behaviour is intentional, except that if an
application other than xine uses the DVB adapter and manages to set the
parameters_out.frequency field to something other than zero, then xine
no longer has any problems until either the adapter is replugged or the
kernel modules reloaded. This can only mean that the
fepriv->parameters_out struct still contains the (stale) tuning
information from the previous application.
Signed-off-by: Chris Rankin <rankincj@yahoo.com> Cc: stable@kernel.org # for kernel version 3.3 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] stb0899: fix the limits for signal strength values
stb0899: fix the limits for signal strength values
stb0899_read_signal_strength() adds an offset to the result of the table lookup.
That offset must correspond to the lowest value in the lookup table, to make sure
the result doesn't get below 0, which would mean a "very high" value since the
parameter is unsigned.
'strength' and 'snr' need to be initialized to 0 to make sure they have a
defined result in case there is no "internal->lock".
Signed-off-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de> Cc: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ivan Kalvachev [Mon, 19 Mar 2012 23:09:55 +0000 (20:09 -0300)]
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
It is mostly copy/paste of the 520e code with setting GPIO7 removed
(no LED light).
I've worked on just released vanilla linux-3.3.0 kernel, so there may
be 1/2 lines offset to the internal working source, but most of the
code should apply cleanly.
I was able to get the DVB-C working (tuned and watched TV). Haven't
tested DVB-T (no signal atm).
Special thanks to everybody who worked on the code and to Antti
Palosaari and Devin Heitmueller who provided essential support on irc.
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
AVF4910 (not used atm)
Signed-off-by: Ivan Kalvachev <ikalvachev@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Mon, 19 Mar 2012 14:48:19 +0000 (11:48 -0300)]
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
... + analog parts.
Analog is not supported currently. Only DVB-T and DVB-C.
There seems to be still problems for locking DVB-C channels which have
strong signal. Attenuator helps. I think it is demodulator IF/RF AGC
issue. Lets fix it later. Patches are welcome.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 8 Feb 2012 11:09:36 +0000 (08:09 -0300)]
[media] -EINVAL -> -ENOTTY
I found one more place where -EINVAL is used instead of -ENOTTY:
Note that drivers/media/dvb/dvb-core/dvbdev.c has the same code, but as far as
I can tell DVB is still using -EINVAL for unknown ioctls so I didn't change
that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- copyright change
- use the kbuild module name for messages
- remove useless code
- add/remove blank lines, parenthesis, braces
- add/change some information messages
The JPEG compression may be adjusted from the packet fill ratio and from
the flag 'USB FIFO full' returned in each frame.
The code is adapted from the one in gspca sonixj and uses a workqueue.
[media] gspca - sn9c20x: Add the JPEG compression quality control
The JPEG compression quality was hardcoded to 95%. This value was too big,
raising often buffer overflows.
This quality is now 80% by default and is settable.
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
This patch is adapted from Sylwester's patch proposed on 2012/02/22.
The JPEG compression control does not work with the autoquality done for the
sensors hv7131r and pas202b.
Michael Krufky [Tue, 7 Feb 2012 16:28:33 +0000 (13:28 -0300)]
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
The D1F5 revision of the WinTV HVR-1900 uses a tda18271c2 tuner
instead of a tda18271c1 tuner as used in revision D1E9. To
account for this, we must hardcode the frontend configuration
to use the same IF frequency configuration for both revisions
of the device.
6MHz DVB-T is unaffected by this issue, as the recommended
IF Frequency configuration for 6MHz DVB-T is the same on both
c1 and c2 revisions of the tda18271 tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Cc: Mike Isely <isely@pobox.com> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Sun, 18 Mar 2012 21:09:01 +0000 (18:09 -0300)]
[media] em28xx: support for 1b80:e425 MaxMedia UB425-TC
Hardware is based of:
Empia EM2874B
Micronas DRX 3913KA2
NXP TDA18271HDC2
Only DVB-C supported currently since missing firmware.
According to my tests, DRX 3913KA2 demodulator requires firmware
in order to support DVB-T mode.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:55 +0000 (19:14 -0300)]
[media] mmp-camera: Don't power up the sensor on resume
We still need to power up the controller to avoid unsightly self-immolation
should something try to access its registers, but the sensor can stay
powered down unless the camera was actually operating at suspend time.
This gets rid of the camera LED flash on resume, fixing OLPC bug #11644.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:54 +0000 (19:14 -0300)]
[media] marvell-cam: Don't signal multiple frame completions in scatter/gather mode
There is only one frame known to the DMA engine in scatter/gather mode, but
it still tells us that any or all of frames 1-3 are done at each completion
interrupt. Avoid the creation of junk frames by being sure to only
"complete" one on each interrupt.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:53 +0000 (19:14 -0300)]
[media] marvell-cam: fix the green screen of death
I had learned through hard experience that dinking around with the DMA
descriptors while the C1_DESC_ENA enable bit was set is a recipe for all
kinds of truly malicious behavior on the hardware's part, regardless of
whether the DMA engine is actually operating at the time. That
notwithstanding, the driver did so dink, resulting in "green frame"
captures and the death of the system in random, spectacular ways.
Move the tweaking of C1_DESC_ENA to the same function that sets the
descriptor so we know that we'll never try to set a descriptor while that
bit is set.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:52 +0000 (19:14 -0300)]
[media] marvell-cam: Increase the DMA shutdown timeout
Experience shows that, on the Armada platform, it can take as much as 120ms
for the DMA engine to actually shut down after it has been told to. So a
40ms timeout is not adequate; use 150ms instead. Also make sure we don't
leave the DMA_ACTIVE flag set once things are down.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:51 +0000 (19:14 -0300)]
[media] marvell-cam: Remove broken "owner" logic
The marvell cam driver retained just enough of the owner-tracking logic
from cafe_ccic to be broken; it could, conceivably, cause the driver to
release DMA memory while the controller is still active. Simply remove the
remaining pieces and ensure that the controller is stopped before we free
things.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Fri, 16 Mar 2012 22:14:50 +0000 (19:14 -0300)]
[media] marvell-cam: ensure that the camera stops when requested
The controller stop/restart logic could possibly restart DMA after the
driver things things have stopped, with suitably ugly results. Make sure
that we only restart the hardware if we're supposed to be streaming.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: soc-camera: call soc_camera_power_on() after adding the client to the host
soc_camera_power_on() calls client's .s_power(1) method, which can try to
access the client hardware. This, however, is typically only possible,
after calling host's .add() method, because that's where the host driver
usually turns the master clock on.
Ezequiel García [Thu, 15 Mar 2012 19:53:49 +0000 (16:53 -0300)]
[media] rc: Pospone ir raw decoders loading until really needed
This changes rc_core to not load the IR decoders at load time,
postponing it to load only if a RC_DRIVER_IR_RAW device is
registered via rc_register_device.
We use a static boolean variable, to ensure decoders modules
are only loaded once.
Tested with rc-loopback device only.
[media] m88rs2000 ver 1.13 Correct deseqc and tuner gain functions
Remove incorrect SEC_MINI_B settings-TODO complete this section.
Correct break and remove return -EINVAL within set tone. It appears
there is a bug that occasionally something other than ON/OFF is
sent stalling the driver. Just continue and write back registers.
Set register b2 in setup. This is the set voltage pin which
isn't used in lmedm04 driver but it is always set to 0x1.
Antti Palosaari [Wed, 14 Mar 2012 13:27:31 +0000 (10:27 -0300)]
[media] af9015: fix i2c failures for dual-tuner devices - part 2
Some changes for previous patch I liked to do.
Just move tuner init and sleep to own functions from the demod
init and sleep functions. Functionality remains still almost the same.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gordon Hecker [Wed, 14 Mar 2012 13:27:30 +0000 (10:27 -0300)]
[media] af9015: fix i2c failures for dual-tuner devices
The i2c failures were caused by enabling both i2c gates
at the same time while putting the tuners asleep.
This patch removes the init() and sleep() callbacks from the tuner,
to prevent frontend.c from calling
i2c_gate_ctrl
tuner init / sleep
i2c_gate_ctrl
without holding the lock.
tuner init() and sleep() are instead called in frontend init() and
sleep().
Signed-off-by: Gordon Hecker <ghecker@gmx.de> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Tue, 13 Mar 2012 16:50:37 +0000 (13:50 -0300)]
[media] dib0700: Drop useless check when remote key is pressed
struct dvb_usb_device *d can never be NULL so don't waste time
checking for this.
Rationale: the urb's context is set when usb_fill_bulk_urb() is called
in dib0700_rc_setup(), and never changes after that. d is dereferenced
unconditionally in dib0700_rc_setup() so it can't be NULL or the
driver would crash right away.
Michael Krufky [Mon, 12 Mar 2012 20:07:22 +0000 (17:07 -0300)]
[media] au8522: bug-fix: enable modulation AFTER tune (instead of before tuning)
The au8522 driver programs the tuner after programming the demodulator,
but the tuner should be programmed first. This patch fixes this behavior.
EDIT: Apparantly Devin created a similar patch some time ago, but hasn't
submitted it for merge. I never saw his patch, but I thank him anyhow
for his efforts. In addition, Devin pointed out a flaw in my patch:
This newly generated patch takes Devin's comments into account.
Laurent Pinchart [Mon, 12 Mar 2012 13:02:47 +0000 (10:02 -0300)]
[media] media: Initialize the media core with subsys_initcall()
Media-related drivers living outside drivers/media/ (such as the UVC
gadget driver in drivers/usb/gadget/) rely on the media core being
initialized before they're probed. As drivers/usb/ is linked before
drivers/media/, this is currently not the case and will lead to crashes
if the drivers are not compiled as modules.
Register media_devnode_init() as a subsys_initcall() instead of
module_init() to fix this.
Bhupesh Sharma [Mon, 12 Mar 2012 08:09:02 +0000 (05:09 -0300)]
[media] V4L/v4l2-dev: Make 'videodev_init' as a subsys initcall
As the V4L2 based UVC webcam gadget (g_webcam) expects the
'videodev' to present when the 'webcam_bind' routine is called,
so 'videodev' should be available as early as possible.
Now, when 'g_webcam' is built as a module (i.e. not a part of
kernel) the late availability of 'videodev' is OK, but if
'g_webcam' is built statically as a part of the kernel,
the kernel crashes (a sample crash dump using Designware 2.0 UDC
is provided below).
To solve the same, this patch makes 'videodev_init' as a subsys initcall.
[media] v4l: Add driver for Micron MT9M032 camera sensor
The MT9M032 is a parallel 1.6MP sensor from Micron controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports cropping, gain,
exposure and v/h flipping controls in monochrome mode with an
external pixel clock.
Akihiro Tsukada [Sat, 10 Mar 2012 14:38:13 +0000 (11:38 -0300)]
[media] dvb: earth-pt1: stop polling data when no one accesses the device
The driver started a kthread to poll the DMA buffers soon after probing,
which relsuleted in 1000/sec sleeps and wakeups of the thread doing nothing
useful until someone started feeding.
This patch changes the creation and destruction of the kthread depending on the number of users.
Ezequiel García [Sat, 10 Mar 2012 14:34:27 +0000 (11:34 -0300)]
[media] media: em28xx: Remove unused urb arrays from device struct
These arrays were embedded in the struct itself, but they weren't
used by anyone, since urbs are now dinamically allocated
at em28xx_usb_isoc_ctl struct.
Tested by compilation only.
Dan Carpenter [Sat, 10 Mar 2012 07:58:18 +0000 (04:58 -0300)]
[media] gpio-ir-recv: a couple signedness bugs
There are couple places where we check unsigned values for negative. I
changed ->gpin_nr to signed because in gpio_ir_recv_probe() we do:
if (pdata->gpio_nr < 0)
return -EINVAL;
I also change gval to a signed int in gpio_ir_recv_irq() because that's
the type that gpio_get_value_cansleep() returns and we test for negative
returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Trilok Soni <tsoni@codeaurora.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] s5p-csis: Fix compilation with PM_SLEEP disabled
Fix following compilation error when CONFIG_PM_SLEEP is disabled:
CC drivers/media/video/s5p-fimc/mipi-csis.o
drivers/media/video/s5p-fimc/mipi-csis.c: In function ‘s5pcsis_remove’:
drivers/media/video/s5p-fimc/mipi-csis.c:956: error: implicit declaration of function ‘s5pcsis_suspend’
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/w9966.c: In function ‘__check_pardev’:
drivers/media/video/w9966.c:136:1: warning: return from incompatible pointer type [enabled by default]
Fabio Estevam [Fri, 9 Mar 2012 11:15:38 +0000 (08:15 -0300)]
[media] video: Kconfig: Select VIDEOBUF2_DMA_CONTIG for VIDEO_MX2
Fix the following build error:
LD .tmp_vmlinux1
drivers/built-in.o: In function `mx2_camera_init_videobuf':
clkdev.c:(.text+0xcfaf4): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx2_camera_probe':
clkdev.c:(.devinit.text+0x5734): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x5778): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx2_camera_remove':
clkdev.c:(.devexit.text+0x89c): undefined reference to `vb2_dma_contig_cleanup_ctx'
commit c6a41e3271 ([media] media i.MX27 camera: migrate driver to videobuf2)
missed to select VIDEOBUF2_DMA_CONTIG in Kconfig.
[media] V4L: Improve the selection API documentation
Make the VIDIOC_G/S_SELECTION ioctls documentation more consistent
with the rest of media Docbook, use capital letters where necessary
and correct few minor errors.
This field is handled internally by the DVB core, with uses the
selected delivery system to fill it, when a DVBv3 call is
handled. So, drivers should not touch on it.
[media] m88rs2000 1.12 v2 DVB-S frontend and tuner module
Support for m88rs2000 chip used in lmedm04 driver.
Note there are still lock problems.
Slow channel change due to the large block of registers sent in set_frontend.
Version 2 differences.
Front end is completely shut down when in sleep mode. This allow user to regain
control of device.
Kaffeine scan problem solved by removing register calls from get_frontend.
Kaffeine seems to call get_frontend when updating signal data. This can happen
in the middle of a tune stalling the driver.
Change calculations to those in the DS3000 driver.
[media] dib9000: implement error handling for DibAcquireLock
DibAcquireLock() is implemented as mutex_lock_interruptible()
but the driver does not handle unsuccessful locking.
As a result it may lead to unlock of an unheld mutex.
Found by Linux Driver Verification project (linuxtesting.org).
[media] as102: set optimal eLNA config values for each device
Ryley and me tested several eLNA configuration values with both a rooftop
and a portable antenna.
Ryley fuond out that the best value for his Elgato stick is indeed the current
default value 0xC0.
Instead, my stick is not capable of tuning VHF channels with 0xC0. With 0x80,
VHF works but the tuner sensitivity with the portable antenna is poor.
Instead, the value 0xA0 works with VHF and also gives good performance with
both the rooftop and the portable antenna.
So we concluded that devices built on the reference design work best with 0xA0,
while custom designs (Elgato, PCTV) seem to require 0xC0.
I also removed the unused parameter "minor" in struct as102_dev_t.
[media] as102: add __packed attribute to structs defined inside packed structs
This patch fixes a regression in kernel 3.3 due to this patch:
http://patchwork.linuxtv.org/patch/8332/
That patch changes "#pragma pack(1)" with "__packed" attributes, but it is not
complete. In fact, in the as102 driver there are a lot of structs/unions
defined inside other structs/unions.
When the "__packed" attribute is applied only on the external struct, it will
not affect the internal struct definitions.
So the regression is fixed by specifiying the "__packed" attribute also on the
internal structs.
This patch should go into 3.3, as it fixes a regression introduced in the new
kernel version.
Jesper Juhl [Sun, 4 Mar 2012 19:25:04 +0000 (16:25 -0300)]
[media] media, cx231xx: Fix double free on close
In cx231xx_v4l2_close() there are two calls to
cx231xx_release_resources(dev) followed by kfree(dev). That is a
problem since cx231xx_release_resources() already kfree()'s its
argument, so we end up doing a double free.
Easily resolved by just removing the redundant kfree() calls after the
calls to cx231xx_release_resources().
I also changed the 'dev = NULL' assignments (which are rather
pointless since 'dev' is about to go out of scope), to 'fh->dev = NULL'
since it looks to me that that is what was actually intended.
And I removed the 'dev = NULL' assignment at the end of
cx231xx_release_resources() since it is pointless.
projects / linux-beck.git / log