Roger Quadros [Tue, 2 Sep 2014 13:57:06 +0000 (16:57 +0300)]
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Pekon Gupta <pekon@pek-sem.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 2 Sep 2014 13:57:05 +0000 (16:57 +0300)]
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Pekon Gupta <pekon@pek-sem.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 2 Sep 2014 13:57:04 +0000 (16:57 +0300)]
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
Roger Quadros [Tue, 2 Sep 2014 13:57:03 +0000 (16:57 +0300)]
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Pekon Gupta <pekon@pek-sem.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 2 Sep 2014 13:57:02 +0000 (16:57 +0300)]
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Pekon Gupta <pekon@pek-sem.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Al Viro [Thu, 4 Sep 2014 13:38:11 +0000 (09:38 -0400)]
udf: fix the udf_iget() vs. udf_new_inode() races
Currently udf_iget() (triggered by NFS) can race with udf_new_inode()
leading to two inode structures with the same inode number:
nfsd: iget_locked() creates inode
nfsd: try to read from disk, block on that.
udf_new_inode(): allocate inode with that inumber
udf_new_inode(): insert it into icache, set it up and dirty
udf_write_inode(): write inode into buffer cache
nfsd: get CPU again, look into buffer cache, see nice and sane on-disk
inode, set the in-core inode from it
Fix the problem by putting inode into icache in locked state (I_NEW set)
and unlocking it only after it's fully set up.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Thu, 4 Sep 2014 14:26:19 +0000 (16:26 +0200)]
udf: Set i_generation field
Currently UDF doesn't initialize i_generation in any way and thus NFS
can easily get reallocated inodes from stale file handles. Luckily UDF
already has a unique object identifier associated with each inode -
i_unique. Use that for initialization of i_generation.
Jan Kara [Thu, 4 Sep 2014 14:19:47 +0000 (16:19 +0200)]
udf: Properly detect stale inodes
NFS can easily ask for inodes that are already deleted. Currently UDF
happily returns such inodes which is a bug. Return -ESTALE if
udf_read_inode() is asked to read deleted inode.
Jan Kara [Thu, 4 Sep 2014 14:15:51 +0000 (16:15 +0200)]
udf: Make udf_read_inode() and udf_iget() return error
Currently __udf_read_inode() wasn't returning anything and we found out
whether we succeeded reading inode by checking whether inode is bad or
not. udf_iget() returned NULL on failure and inode pointer otherwise.
Make these two functions properly propagate errors up the call stack and
use the return value in callers.
Merge tag 'mac80211-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon bugfix from Guenter Roeck:
"Fix a bug in the ds1621 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Update zbits after conversion rate change
Merge tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
Li Zefan [Thu, 4 Sep 2014 06:43:38 +0000 (14:43 +0800)]
cgroup: check cgroup liveliness before unbreaking kernfs
When cgroup_kn_lock_live() is called through some kernfs operation and
another thread is calling cgroup_rmdir(), we'll trigger the warning in
cgroup_get().
We clear cgrp->kn->priv in the end of cgroup_rmdir(), but another
concurrent thread can access kn->priv after the clearing.
We should move the clearing to css_release_work_fn(). At that time
no one is holding reference to the cgroup and no one can gain a new
reference to access it.
v2:
- move RCU_INIT_POINTER() into the else block. (Tejun)
- remove the cgroup_parent() check. (Tejun)
- update the comment in css_tryget_online_from_dir().
Merge tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time it contains a bunch of small ASoC fixes that slipped from in
previous updates, in addition to the usual HD-audio fixes and the
regression fixes for FireWire updates in 3.17.
All commits are reasonably small fixes"
* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix COEF setups for ALC1150 codec
ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
ALSA: hda - Fix digital mic on Acer Aspire 3830TG
ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
ALSA: dice: fix wrong channel mappping at higher sampling rate
ASoC: cs4265: Fix setting of functional mode and clock divider
ASoC: cs4265: Fix clock rates in clock map table
ASoC: rt5677: correct mismatch widget name
ASoC: rt5640: Do not allow regmap to use bulk read-write operations
ASoC: tegra: Fix typo in include guard
ASoC: da732x: Fix typo in include guard
ASoC: core: fix .info for SND_SOC_BYTES_TLV
ASoC: rcar: Use && instead of & for boolean expressions
ASoC: Use dev_set_name() instead of init_name
ASoC: axi: Fix ADI AXI SPDIF specification
Jan Kara [Thu, 4 Sep 2014 12:06:55 +0000 (14:06 +0200)]
udf: Avoid infinite loop when processing indirect ICBs
We did not implement any bound on number of indirect ICBs we follow when
loading inode. Thus corrupted medium could cause kernel to go into an
infinite loop, possibly causing a stack overflow.
Fix the possible stack overflow by removing recursion from
__udf_read_inode() and limit number of indirect ICBs we follow to avoid
infinite loops.
Jan Kara [Thu, 4 Sep 2014 09:47:51 +0000 (11:47 +0200)]
udf: Avoid dir link count to go negative
If we are writing back inode of unlinked directory, its link count ends
up being (u16)-1. Although the inode is deleted, udf_iget() can load the
inode when NFS uses stale file handle and get confused.
Li RongQing [Wed, 3 Sep 2014 09:43:45 +0000 (17:43 +0800)]
openvswitch: distinguish between the dropped and consumed skb
distinguish between the dropped and consumed skb, not assume the skb
is consumed always
Cc: Thomas Graf <tgraf@noironetworks.com> Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several bug fixes for issues that have been lurking for a while:
- Check that devices haven't set the flag saying they only support
register at a time operation while we're doing cache syncs,
otherwise we fail to restore caches
- Ensure that we don't mark all registers on devices using
format_write() as cacheable, avoiding adding a cache of things like
reset registers which we don't want to rewrite during cache sync
- Make sure we create the debugfs files in the correct directory"
* tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Don't attempt block writes when syncing cache on single_rw devices
regmap: Fix handling of volatile registers for format_write() chips
regmap: Fix regcache debugfs initialization
Roger Quadros [Wed, 3 Sep 2014 11:17:32 +0000 (14:17 +0300)]
ARM: dts: dra7-evm: Fix 8th NAND partition's name
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573b2 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573b2 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace) Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dan Carpenter [Wed, 3 Sep 2014 11:44:37 +0000 (14:44 +0300)]
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
The current code just returns -EINVAL because mode can't be equal to
both 1 and 2.
Also this function is messy so I have cleaned it up:
1) Remove initializers like "int time = -1". Initializing variables to
garbage values turns off GCC's uninitialized variable warnings so it
can lead to bugs.
2) Use kstrtoint() instead of sscanf().
3) Use SCI_KBD_MODE_FNZ and SCI_KBD_MODE_AUTO instead of magic numbers 1
and 2.
4) Don't check for "mode == -1" because that can't happen.
5) Preserve the error code from toshiba_kbd_illum_status_set().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Merge tag 'for-f2fs-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs bug fixes from Jaegeuk Kim:
"This series includes patches to:
- fix recovery routines
- fix bugs related to inline_data/xattr
- fix when casting the dentry names
- handle EIO or ENOMEM correctly
- fix memory leak
- fix lock coverage"
* tag 'for-f2fs-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (28 commits)
f2fs: reposition unlock_new_inode to prevent accessing invalid inode
f2fs: fix wrong casting for dentry name
f2fs: simplify by using a literal
f2fs: truncate stale block for inline_data
f2fs: use macro for code readability
f2fs: introduce need_do_checkpoint for readability
f2fs: fix incorrect calculation with total/free inode num
f2fs: remove rename and use rename2
f2fs: skip if inline_data was converted already
f2fs: remove rewrite_node_page
f2fs: avoid double lock in truncate_blocks
f2fs: prevent checkpoint during roll-forward
f2fs: add WARN_ON in f2fs_bug_on
f2fs: handle EIO not to break fs consistency
f2fs: check s_dirty under cp_mutex
f2fs: unlock_page when node page is redirtied out
f2fs: introduce f2fs_cp_error for readability
f2fs: give a chance to mount again when encountering errors
f2fs: trigger release_dirty_inode in f2fs_put_super
f2fs: don't skip checkpoint if there is no dirty node pages
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key subsystem fixes from James Morris:
"Fixes for the keys subsystem, one of which addresses a use-after-free
bug"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
PEFILE: Relax the check on the length of the PKCS#7 cert
KEYS: Fix use-after-free in assoc_array_gc()
KEYS: Fix public_key asymmetric key subtype name
KEYS: Increase root_maxkeys and root_maxbytes sizes
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
Merge branch 'leds-fixes-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED fix from Bryan Wu:
"Hugh, Jiri and many other people found a kernel oops due to a LED
change merged recently. Now the right fix might just revert it and
avoid the kernel oops"
* 'leds-fixes-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
Revert "leds: convert blink timer to workqueue"
Merge branch 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/urgent
Pull an RCU fix from Paul E. McKenney:
"This series contains a single commit fixing an initialization bug
reported by Amit Shah and fixed by Pranith Kumar (and tested by Amit).
This bug results in a boot-time hang in callback-offloaded configurations
where callbacks were posted before the offloading ('rcuo') kthreads
were created."
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru> Cc: Paul Mackerras <paulus@samba.org> Cc: Alexander Graf <agraf@suse.de> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Airlie [Wed, 3 Sep 2014 03:39:47 +0000 (13:39 +1000)]
Merge branch 'vmwgfx-fixes-3.17' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Two vmwgfx fixes, marked for stable as well
* 'vmwgfx-fixes-3.17' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix a potential infinite spin waiting for fifo idle
drm/vmwgfx: Fix an incorrect OOM return value
The wrapper is the first 8 bytes of the hex dump inside []. This indicates a
length of 0x968 bytes, including the wrapper header - so 0x960 bytes of
payload.
The ASN.1 wrapper begins [ ... 30 82 09 56 ]. That indicates an object of size
0x956 - a four byte discrepency, presumably just padding for alignment
purposes.
So we just check that the ASN.1 container is no bigger than the payload and
reduce the recorded size appropriately.
Whilst we're at it, allow shorter PKCS#7 objects that manage to squeeze within
127 or 255 bytes. It's just about conceivable if no X.509 certs are included
in the PKCS#7 message.
Reported-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Vivek Goyal <vgoyal@redhat.com> Acked-by: Peter Jones <pjones@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
David Howells [Tue, 2 Sep 2014 12:52:10 +0000 (13:52 +0100)]
KEYS: Fix public_key asymmetric key subtype name
The length of the name of an asymmetric key subtype must be stored in struct
asymmetric_key_subtype::name_len so that it can be matched by a search for
"<subkey_name>:<partial_fingerprint>". Fix the public_key subtype to have
name_len set.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Steve Dickson [Tue, 2 Sep 2014 12:52:05 +0000 (13:52 +0100)]
KEYS: Increase root_maxkeys and root_maxbytes sizes
Now that NFS client uses the kernel key ring facility to store the NFSv4
id/gid mappings, the defaults for root_maxkeys and root_maxbytes need to be
substantially increased.
Signed-off-by: Steve Dickson <steved@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Jason Baron [Thu, 14 Aug 2014 14:26:08 +0000 (14:26 +0000)]
powercap / RAPL: add support for CPU model 0x3f
I've confirmed that monitoring the package power usage as well as setting power
limits appear to be working as expected. Supports the package and dram domains.
Tested aginst cpu:
Intel(R) Xeon(R) CPU E5-2650 v3 @ 2.30GHz
Signed-off-by: Jason Baron <jbaron@akamai.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit d431cbc53cb7 (PM / sleep: Simplify sleep states sysfs
interface code) the pm_states[] array is not populated initially,
which causes setup_test_suspend() to always fail and the suspend
testing during boot doesn't work any more.
Fix the problem by using pm_labels[] instead of pm_states[] in
setup_test_suspend() and storing a pointer to the label of the
sleep state to test rather than the number representing it,
because the connection between the state numbers and labels is
only established by suspend_set_ops().
Fixes: d431cbc53cb7 (PM / sleep: Simplify sleep states sysfs interface code) Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
On the Toshiba Tecra Z40, after a suspend-to-disk, some FN hotkeys
driven by toshiba_acpi are not functional.
Calling the ACPI object ENAB on resume makes them back alive.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Mathias Krause [Thu, 28 Aug 2014 11:02:49 +0000 (13:02 +0200)]
ideapad-laptop: Constify DMI table for real!
This is a follow-up patch to commit 49458e83082d ("ideapad-laptop:
Constify DMI table and other r/o variables") to do what its commit
message says. The actual commit differs from the patch posted at
https://www.mail-archive.com/platform-driver-x86@vger.kernel.org/msg05340.html
significantly, probably due to a bad merge conflict resolution. Fix up
the mess and constify the DMI table for real and fix the bogus
double-const of ideapad_rfk_data[].
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Matthew Garrett <matthew.garrett@nebula.com> Cc: Ike Panhc <ike.pan@canonical.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
amd-xgbe: Fix initialization of the wrong spin lock
During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Tue, 2 Sep 2014 12:52:28 +0000 (20:52 +0800)]
openvswitch: fix a memory leak
The user_skb maybe be leaked if the operation on it failed and codes
skipped into the label "out:" without calling genlmsg_unicast.
Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira [Tue, 2 Sep 2014 12:26:17 +0000 (14:26 +0200)]
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
make defconfig reports:
warning: (NETFILTER_XT_TARGET_LOG) selects NF_LOG_IPV6 which has unmet direct dependencies (NET && INET && IPV6 && NETFILTER && NETFILTER_ADVANCED)
Fixes: d79a61d netfilter: NETFILTER_XT_TARGET_LOG selects NF_LOG_* Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
pull request: Netfilter/IPVS fixes for net
The following patchset contains seven Netfilter fixes for your net
tree, they are:
1) Make the NAT infrastructure independent of x_tables, some users are
already starting to test nf_tables with NAT without enabling x_tables.
Without this patch for Kconfig, there's a superfluous dependency
between NAT and x_tables.
2) Allow to use 0 in the cgroup match, the kernel rejects with -EINVAL
with no good reason. From Daniel Borkmann.
3) Select CONFIG_NF_NAT from the nf_tables NAT expression, this also
resolves another NAT dependency with x_tables.
4) Use HAVE_JUMP_LABEL instead of CONFIG_JUMP_LABEL in the Netfilter hook
code as elsewhere in the kernel to resolve toolchain problems, from
Zhouyi Zhou.
5) Use iptunnel_handle_offloads() to set up tunnel encapsulation
depending on the offload capabilities, reported by Alex Gartrell
patch from Julian Anastasov.
6) Fix wrong family when registering the ip_vs_local_reply6() hook,
also from Julian.
7) Select the NF_LOG_* symbols from NETFILTER_XT_TARGET_LOG. Rafał
Miłecki reported that when jumping from 3.16 to 3.17-rc, his log
target is not selected anymore due to changes in the previous
development cycle to accomodate the full logging support for
nf_tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Configure device endianity on driver load and reset endianity on removal.
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth device is queried for ethtool data, hardware operation
is performed to extract the necessary information from the card.
If the card is not online at the moment (e.g. it is undergoing
recovery), this operation produces undesired effects like
temporarily freezing the system. This patch prevents execution
of the hardware query operation when the card is not online.
In such case, ioctl() operation returns error with errno ENODEV.
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Simon Horman <horms@verge.net.au> Cc: Magnus Damm <magnus.damm@gmail.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Mon, 1 Sep 2014 12:21:57 +0000 (14:21 +0200)]
tg3: prevent ifup/ifdown during PCI error recovery
The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.
First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.
Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().
v2: Added logging messages per Prashant's request
Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Moyer [Tue, 2 Sep 2014 17:17:00 +0000 (13:17 -0400)]
aio: add missing smp_rmb() in read_events_ring
We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events. After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves. This small patch fixes the
problem in testing.
Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Cc: stable@vger.kernel.org
Analogous to commit 8858d88a25142544843869f0cd3e6654aa7b4aec
that fixed commit 70b41abc151f9
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org>
It's broken as it changes led_blink_set() in a way that it can now sleep
(while synchronously waiting for workqueue to be cancelled). That's a
problem, because it's possible that this function gets called from atomic
context (tpt_trig_timer() takes a readlock and thus disables preemption).
This has been brought up 3 weeks ago already [1] but no proper fix has
materialized, and I keep seeing the problem since 3.17-rc1.
Marek Roszko [Thu, 21 Aug 2014 01:39:41 +0000 (21:39 -0400)]
i2c: at91: add bound checking on SMBus block length bytes
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
addy ke [Fri, 22 Aug 2014 18:00:52 +0000 (02:00 +0800)]
i2c: rk3x: fix bug that cause transfer fails in master receive mode
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com> Acked-by: Max Schwarz <max.schwarz@online.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Simon Lindgren [Tue, 26 Aug 2014 19:13:24 +0000 (21:13 +0200)]
i2c: at91: Fix a race condition during signal handling in at91_do_twi_xfer.
There is a race condition in at91_do_twi_xfer when signals arrive.
If a signal is recieved while waiting for a transfer to complete
wait_for_completion_interruptible_timeout() will return -ERESTARTSYS.
This is not handled correctly resulting in interrupts still being
enabled and a transfer being in flight when we return.
Symptoms include a range of oopses and bus lockups. Oopses can happen
when the transfer completes because the interrupt handler will corrupt
the stack. If a new transfer is started before the interrupt fires
the controller will start a new transfer in the middle of the old one,
resulting in confused slaves and a locked bus.
To avoid this, use wait_for_completion_io_timeout instead so that we
don't have to deal with gracefully shutting down the transfer and
disabling the interrupts.
Signed-off-by: Simon Lindgren <simon@aqwary.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
i2c: mv64xxx: continue probe when clock-frequency is missing
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c19bb ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: stable@vger.kernel.org Acked-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sergei Shtylyov [Mon, 1 Sep 2014 21:15:26 +0000 (01:15 +0400)]
i2c: rcar: fix MNR interrupt handling
Sometimes the MNR and MST interrupts happen simultaneously (stop automatically
follows NACK, according to the manuals) and in such case the ID_NACK flag isn't
set since the MST interrupt handling precedes MNR and all interrupts are cleared
and disabled then, so that MNR interrupt is never noticed -- this causes NACK'ed
transfers to be falsely reported as successful. Exchanging MNR and MST handlers
fixes this issue, however the MNR bit somehow gets set again even after being
explicitly cleared, so I decided to completely suppress handling of all disabled
interrupts (which is a good thing anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Ville Syrjälä [Tue, 2 Sep 2014 09:57:22 +0000 (12:57 +0300)]
drm/i915: Fix lock dropping in intel_tv_detect()
When intel_tv_detect() fails to do load detection it would forget to
drop the locks and clean up the acquire context. Fix it up.
This is a regression from:
commit 208bf9fdcd3575aa4a5d48b3e0295f7cdaf6fc44
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 11 13:15:35 2014 +0300
drm/i915: Fix locking for intel_enable_pipe_a()
v2: Make the code more readable (Chris)
v3: Drop WARN_ON(type < 0) (Chris)
Cc: stable@vger.kernel.org Cc: Tibor Billes <tbilles@gmx.com> Reported-by: Tibor Billes <tbilles@gmx.com> Tested-by: Tibor Billes <tbilles@gmx.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
commit 0944fe3f4a32 ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: stable@vger.kernel.org # v3.12+
KVM: s390/mm: Fix storage key corruption during swapping
Since 3.12 or more precisely commit 0944fe3f4a32 ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: stable@vger.kernel.org # v3.12+
commit 39b2bbe3d715cf5013b5c48695ccdd25bd3bf120
"gpio: add flags argument to gpiod_get*() functions"
added a dynamic flags argument to all the GPIOD getter
functions, however this did not cover the stubs so
when people used gpiod stubs to compile out descriptor
code, compilation failed.
Solve this by:
- Also rename all the stub functions __gpiod_*
- Moving the vararg hack outside of #ifdef CONFIG_GPIOLIB
so these will always be available.
Chao Yu [Sat, 30 Aug 2014 01:52:34 +0000 (09:52 +0800)]
f2fs: reposition unlock_new_inode to prevent accessing invalid inode
As the race condition on the inode cache, following scenario can appear:
[Thread a] [Thread b]
->f2fs_mkdir
->f2fs_add_link
->__f2fs_add_link
->init_inode_metadata failed here
->gc_thread_func
->f2fs_gc
->do_garbage_collect
->gc_data_segment
->f2fs_iget
->iget_locked
->wait_on_inode
->unlock_new_inode
->move_data_page
->make_bad_inode
->iput
When we fail in create/symlink/mkdir/mknod/tmpfile, the new allocated inode
should be set as bad to avoid being accessed by other thread. But in above
scenario, it allows f2fs to access the invalid inode before this inode was set
as bad.
This patch fix the potential problem, and this issue was found by code review.
change log from v1:
o Add condition judgment in gc_data_segment() suggested by Changman Lee.
o use iget_failed to simplify code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
David S. Miller [Tue, 2 Sep 2014 06:00:49 +0000 (23:00 -0700)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
Trivial fixes for cxgb4
This patch series adds support to fix T5 adapter accessing T4 adapter registers,
issue mbox command on correct mbox for physical function, avoid dumping write
only registers, use correct length for adapter part number and support to detect
and display firmware reported errors.
The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
Thanks
V2:
Added description for each patch as per David Miller's comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Fixed the code to use correct length for part number
Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Fix for handling 1Gb/s SFP+ Transceiver Modules
We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time. This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec. Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Reported-and-tested-by: Dana Goyette <danagoyette@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches includes fixes to the driver.
- Tx hardware queue flushing support dependent on hardware version
- Incorrect reported fifo size
- Proper mmd select in XPCS debugfs support
- Proper queue count for configuring Tx flow control
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 29 Aug 2014 18:17:08 +0000 (13:17 -0500)]
amd-xgbe: Use the Tx queue count for Tx flow control support
When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 29 Aug 2014 18:17:02 +0000 (13:17 -0500)]
amd-xgbe: Fix the xpcs mmd debugfs support
The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used. Update the debugfs support to generate the
proper mmd register value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 29 Aug 2014 18:16:56 +0000 (13:16 -0500)]
amd-xgbe: Reported fifo size from hardware is not correct
The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present. Also, fix
the argument types used in the fifo size calculation function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 29 Aug 2014 18:16:50 +0000 (13:16 -0500)]
amd-xgbe: Check for Tx hardware queue flushing support
The flushing of the Tx hardware queues is only supported at a certain
level of the hardware. Retrieve the current version of the hardware
and use that to determine if flushing is supported.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `xgene_enet_delete_ring':
xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_setup_tx_desc':
xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_tx_completion':
xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_refill_bufpool':
xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_rx_frame':
xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_free_desc_ring':
xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_create_desc_ring':
xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgene_enet_probe':
xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask'
xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Foster [Tue, 2 Sep 2014 02:12:53 +0000 (12:12 +1000)]
xfs: trim eofblocks before collapse range
xfs_collapse_file_space() currently writes back the entire file
undergoing collapse range to settle things down for the extent shift
algorithm. While this prevents changes to the extent list during the
collapse operation, the writeback itself is not enough to prevent
unnecessary collapse failures.
The current shift algorithm uses the extent index to iterate the in-core
extent list. If a post-eof delalloc extent persists after the writeback
(e.g., a prior zero range op where the end of the range aligns with eof
can separate the post-eof blocks such that they are not written back and
converted), xfs_bmap_shift_extents() becomes confused over the encoded
br_startblock value and fails the collapse.
As with the full writeback, this is a temporary fix until the algorithm
is improved to cope with a volatile extent list and avoid attempts to
shift post-eof extents.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Tue, 2 Sep 2014 02:12:53 +0000 (12:12 +1000)]
xfs: xfs_file_collapse_range is delalloc challenged
If we have delalloc extents on a file before we run a collapse range
opertaion, we sync the range that we are going to collapse to
convert delalloc extents in that region to real extents to simplify
the shift operation.
However, the shift operation then assumes that the extent list is
not going to change as it iterates over the extent list moving
things about. Unfortunately, this isn't true because we can't hold
the ILOCK over all the operations. We can prevent new IO from
modifying the extent list by holding the IOLOCK, but that doesn't
prevent writeback from running....
And when writeback runs, it can convert delalloc extents is the
range of the file prior to the region being collapsed, and this
changes the indexes of all the extents in the file. That causes the
collapse range operation to Go Bad.
The right fix is to rewrite the extent shift operation not to be
dependent on the extent list not changing across the entire
operation, but this is a fairly significant piece of work to do.
Hence, as a short-term workaround for the problem, sync the entire
file before starting a collapse operation to remove all delalloc
ranges from the file and so avoid the problem of concurrent
writeback changing the extent list.
Diagnosed-and-Reported-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
projects / karo-tx-linux.git / log