Jan Glauber [Mon, 4 Apr 2011 07:43:29 +0000 (09:43 +0200)]
[S390] oprofile s390: prevent stack corruption
Prevent stack corruption by memcpy which copies more bytes then
available at the destination. While at it use the new test_facility
to test for the facility bit.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: pcm: fix infinite loop in snd_pcm_update_hw_ptr0()
ALSA: HDA: Add dock mic quirk for Lenovo Thinkpad X220
ALSA: ens1371: fix Creative Ectiva support
ALSA: firewire-speakers: fix hang when unplugging a running device
ASoC: Fix CODEC device name for Corgi
ALSA: hda - Fix pin-config of Gigabyte mobo
ASoC: imx: fix burstsize for DMA
ASoC: imx: set watermarks for mx2-dma
ASoC: twl6040: Return -ENOMEM if create_singlethread_workqueue fails
ASoC: tlv320dac33: Restore L/R DAC power control register
ASoC: Explicitly say registerless widgets have no register
ASoC: tlv320dac33: Fix inconsistent spinlock usage
Kelly Anderson [Fri, 1 Apr 2011 09:58:25 +0000 (11:58 +0200)]
ALSA: pcm: fix infinite loop in snd_pcm_update_hw_ptr0()
When period interrupts are disabled, snd_pcm_update_hw_ptr0() compares
the current time against the time estimated for the current hardware
pointer to detect xruns. The somewhat fuzzy threshold in the while loop
makes it possible that hdelta becomes negative; the comparison being
done with unsigned types then makes the loop go through the entire 263
negative range, and, depending on the value, never reach an unsigned
value that is small enough to stop the loop. Doing this with interrupts
disabled results in the machine locking up.
To prevent this, ensure that the loop condition uses signed types for
both operands so that the comparison is correctly done.
Many thanks to Kelly Anderson for debugging this.
Reported-by: Nix <nix@esperi.org.uk> Reported-by: "Christopher K." <c.krooss@googlemail.com> Reported-and-tested-by: Kelly Anderson <kelly@silka.with-linux.com> Signed-off-by: Kelly Anderson <kelly@silka.with-linux.com>
[cl: remove unneeded casts; use a temp variable] Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: 2.6.38 <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
kdump: Allow shrinking of kdump region to be overridden
powerpc/pmac/smp: Remove no-longer needed preempt workaround
powerpc/smp: Increase vdso_data->processorCount, not just decrease it
powerpc/smp: Create idle threads on demand and properly reset them
powerpc/smp: Don't expose per-cpu "cpu_state" array
powerpc/pmac/smp: Fix CPU hotplug crashes on some machines
powerpc/smp: Add a smp_ops->bringup_up() done callback
powerpc/pmac: Rename cpu_state in therm_pm72 to avoid collision
powerpc/pmac/smp: Properly NAP offlined CPU on G5
powerpc/pmac/smp: Remove HMT changes for PowerMac offline code
powerpc/pmac/smp: Consolidate 32-bit and 64-bit PowerMac cpu_die in one file
powerpc/pmac/smp: Fixup smp_core99_cpu_disable() and use it on 64-bit
powerpc/pmac/smp: Rename fixup_irqs() to migrate_irqs() and use it on ppc32
powerpc/pmac/smp: Fix 32-bit PowerMac cpu_die
powerpc/smp: Remove unused smp_ops->cpu_enable()
powerpc/smp: Remove unused generic_cpu_enable()
powerpc/smp: Fix generic_mach_cpu_die()
powerpc/smp: soft-replugged CPUs must go back to start_secondary
powerpc: Make decrementer interrupt robust against offlined CPUs
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: Pass task_struct to schedule_tail() in ret_from_fork
apbuart: Depend upon sparc.
sparc64: Fix section mis-match errors.
sparc32,leon: Fixed APBUART frequency detection
sparc32, leon: APBUART driver must use archdata to get IRQ number
sparc: Hook up syncfs system call.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
appletalk: Fix OOPS in atalk_release().
mlx4: Fixing bad size of event queue buffer
mlx4: Fixing use after free
bonding:typo in comment
sctp: Pass __GFP_NOWARN to hash table allocation attempts.
connector: convert to synchronous netlink message processing
fib: add rtnl locking in ip_fib_net_exit
atm/solos-pci: Don't flap VCs when carrier state changes
atm/solos-pci: Don't include frame pseudo-header on transmit hex-dump
atm/solos-pci: Use VPI.VCI notation uniformly.
Atheros, atl2: Fix mem leaks in error paths of atl2_set_eeprom
netdev: fix mtu check when TSO is enabled
net/usb: Ethernet quirks for the LG-VL600 4G modem
phylib: phy_attach_direct: phy_init_hw can fail, add cleanup
bridge: mcast snooping, fix length check of snooped MLDv1/2
via-ircc: Pass PCI device pointer to dma_{alloc, free}_coherent()
via-ircc: Use pci_{get, set}_drvdata() instead of static pointer variable
net: gre: provide multicast mappings for ipv4 and ipv6
bridge: Fix compilation warning in function br_stp_recalculate_bridge_id()
net: Fix warnings caused by MAX_SKB_FRAGS change.
Anton Blanchard [Wed, 25 Aug 2010 00:22:58 +0000 (10:22 +1000)]
kdump: Allow shrinking of kdump region to be overridden
On ppc64 the crashkernel region almost always overlaps an area of firmware.
This works fine except when using the sysfs interface to reduce the kdump
region. If we free the firmware area we are guaranteed to crash.
Rename free_reserved_phys_range to crash_free_reserved_phys_range and make
it a weak function so we can override it.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/smp: Create idle threads on demand and properly reset them
Instead of creating idle threads at boot for all possible CPUs, we
create them on demand, like x86 or ARM, and we properly call init_idle
to re-initialize an idle thread when a CPU was unplugged and is now
re-plugged.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pmac/smp: Fix CPU hotplug crashes on some machines
On some machines that use i2c to synchronize the timebases (such
as PowerMac7,2/7,3 G5 machines), hotplug CPU would crash when
putting back a new CPU online due to the underlying i2c bus being
closed.
This uses the newly added bringup_done() callback to move the close
along with other housekeeping calls, and adds a CPU notifier to
re-open the i2c bus around subsequent hotplug operations
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
This is used by some "soft" hotplug implementations. I needs to
call idle_task_exit() when the CPU is going away, and we remove
the now no-longer needed set_cpu_online() and local_irq_enable()
which are handled by the return to start_secondary
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/smp: soft-replugged CPUs must go back to start_secondary
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make decrementer interrupt robust against offlined CPUs
With some implementations, it is possible that a timer interrupt
occurs every few seconds on an offline CPU. In this case, just
re-arm the decrementer and return immediately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Yevgeny Petrilin [Wed, 30 Mar 2011 23:30:17 +0000 (23:30 +0000)]
mlx4: Fixing bad size of event queue buffer
We should reduce the number of reserved completion queues from the total
number of entries. Since the queue size is power of two, not reducing the
reserved entries, caused a double queue size, which may lead to allocation
failures in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Wed, 30 Mar 2011 23:28:52 +0000 (23:28 +0000)]
mlx4: Fixing use after free
In case of allocation failure, tried to use the promiscuous QP
entry that was previously freed.
Now freeing this entry only in case we will not put it back to the list
of promiscuous entries.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 31 Mar 2011 00:51:36 +0000 (17:51 -0700)]
sctp: Pass __GFP_NOWARN to hash table allocation attempts.
Like DCCP and other similar pieces of code, there are mechanisms
here to try allocating smaller hash tables if the allocation
fails. So pass in __GFP_NOWARN like the others do instead of
emitting a scary message.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 31 Mar 2011 00:37:56 +0000 (17:37 -0700)]
sparc64: Fix section mis-match errors.
Fix all of the problems spotted by CONFIG_DEBUG_SECTION_MISMATCH under
arch/sparc during a 64-bit defconfig build.
They fall into two categorites:
1) of_device_id is marked as __initdata, and we can never do this
since these objects sit in the device core data structures way
past boot. So even if a driver will never be reloaded, we have
to keep the device ID table around.
Mark such cases const instead.
2) The bootmem alloc/free handling code in mdesc.c was not fully
marked __init as it should be, thus generating a reference
to free_bootmem_late() (which is __init) from non-__init code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Mon, 28 Mar 2011 08:39:36 +0000 (08:39 +0000)]
connector: convert to synchronous netlink message processing
Commits 01a16b21 (netlink: kill eff_cap from struct netlink_skb_parms)
and c53fa1ed (netlink: kill loginuid/sessionid/sid members from struct
netlink_skb_parms) removed some members from struct netlink_skb_parms
that depend on the current context, all netlink users are now required
to do synchronous message processing.
connector however queues received messages and processes them in a work
queue, which is not valid anymore. This patch converts connector to do
synchronous message processing by invoking the registered callback handler
directly from the netlink receive function.
In order to avoid invoking the callback with connector locks held, a
reference count is added to struct cn_callback_entry, the reference
is taken when finding a matching callback entry on the device's queue_list
and released after the callback handler has been invoked.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Mar 2011 23:57:46 +0000 (16:57 -0700)]
fib: add rtnl locking in ip_fib_net_exit
Daniel J Blueman reported a lockdep splat in trie_firstleaf(), caused by
RTNL being not locked before a call to fib_table_flush()
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atm/solos-pci: Don't flap VCs when carrier state changes
Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.
We no longer use release_vccs() so we can delete it.
release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atm/solos-pci: Don't include frame pseudo-header on transmit hex-dump
Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.
Also include the size, vpi, and vci in the debug as is done on
receive.
Use "port" consistently instead of "device" intermittently.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 30 Mar 2011 16:46:36 +0000 (09:46 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix whitespace coding style issues
nilfs2: fix oops due to a bad aops initialization
nilfs2: fix data loss in mmap page write for hole blocks
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: Create a new key type "ceph".
libceph: Get secret from the kernel keys api when mounting with key=NAME.
ceph: Move secret key parsing earlier.
libceph: fix null dereference when unregistering linger requests
ceph: unlock on error in ceph_osdc_start_request()
ceph: fix possible NULL pointer dereference
ceph: flush msgr_wq during mds_client shutdown
Linus Torvalds [Wed, 30 Mar 2011 16:35:52 +0000 (09:35 -0700)]
Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63ff ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc96 ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
Linus Torvalds [Wed, 30 Mar 2011 14:53:17 +0000 (07:53 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/qe_ic: Fix another breakage from the irq_data conversion
powerpc/8xx: Fix another breakage from the irq_data conversion
powerpc/cell: Use handle_edge_eoi_irq for real
powerpc/pseries: Enable Chelsio network and iWARP drivers
powerpc/mm: Move the STAB0 location to 0x8000 to make room in low memory
powerpc: Fix accounting of softirq time when idle
powerpc/pseries/smp: query-cpu-stopped-state support won't change
powerpc/xics: Use hwirq for xics domain irq number
powerpc/xics: Fix numberspace mismatch from irq_desc conversion
powerpc: Wire up new syscalls
powerpc/booke: Correct the SPRN_MAS5 definition.
powerpc: ARCH_PFN_OFFSET should be unsigned long
powerpc: Implement dma_mmap_coherent()
powerpc/nvram: Don't overwrite oops/panic report on normal shutdown
powerpc: Restore some misc devices to our configs
Linus Torvalds [Wed, 30 Mar 2011 14:51:29 +0000 (07:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bitops: fix include order after little endian inclusion
Blackfin: defconfigs: update after misc devices defaulted to N
Blackfin: use more standard pr_fmt in the module loader
Daniel Hellstrom [Wed, 30 Mar 2011 01:12:41 +0000 (01:12 +0000)]
sparc32,leon: Fixed APBUART frequency detection
The UARTs may be located on different APB buses, thus have
different UART clock frequency. The system frequency is not
the same (but often) as the UART frequency, rather the APB bus
frequency that the APBUART is located at has the same
frequency, so this looks at the "freq" property instead.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Likely [Wed, 30 Mar 2011 06:02:29 +0000 (00:02 -0600)]
arm: versatile : Fix typo introduced in irq namespace cleanup
Commit 6845664(arm: Cleanup the irq namespace) introduces a typo
causing a build failure for the versatile platform.
[ tglx: Sorry, my bad. Have no idea how I fatfingered that ]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <20110330060229.27397.7628.stgit@ponder> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jesper Juhl [Sun, 27 Mar 2011 09:16:12 +0000 (09:16 +0000)]
Atheros, atl2: Fix mem leaks in error paths of atl2_set_eeprom
We leak in some error paths of drivers/net/atlx/atl2.c:atl2_set_eeprom().
The memory allocated to 'eeprom_buff' is not freed when we return -EIO.
This patch fixes that up and also removes a pointless explicit cast.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Wed, 30 Mar 2011 09:42:17 +0000 (02:42 -0700)]
netdev: fix mtu check when TSO is enabled
In case the device where is coming from the packet has TSO enabled,
we should not check the mtu size value as this one could be bigger
than the expected value.
This is the case for the macvlan driver when the lower device has
TSO enabled. The macvlan inherit this feature and forward the packets
without fragmenting them. Then the packets go through dev_forward_skb
and are dropped. This patch fix this by checking TSO is not enabled
when we want to check the mtu size.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/usb: Ethernet quirks for the LG-VL600 4G modem
This adds a driver for the CDC Ethernet part of this modem. The
device's ID is blacklisted in cdc_ether.c and is white-listed in
this new driver because of the quirks needed to make it useful.
The modem's firmware exposes a CDC ACM port for modem control and a
CDC Ethernet port for network data. The descriptors look fine but
both ports actually are some sort of multiplexers requiring non-
standard headers added/removed from every packet or they get
ignored. All information is based on a usb traffic log from a
Windows machine.
On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with
this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps.
Userspace scripts are required to talk to the CDC ACM port.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
phylib: phy_attach_direct: phy_init_hw can fail, add cleanup
The function phy_attach_direct attaches the phy and calls phy_init_hw.
phy_init_hw can fail, but the phy is still marked as attached. Successive
calls to phy_attach_direct will fail because the phy is busy.
[ 1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1)
[ 1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
[ 2.050000] Sending DHCP requests .
[ 3.020000] PHY: 1:00 - Link is Up - 100/Full
[ 5.110000] ..... timed out!
[ 87.660000] IP-Config: Reopening network devices...
[ 88.190000] FEC: MDIO read timeout
[ 88.190000] eth0: could not attach to PHY
[ 88.190000] IP-Config: Failed to open eth0
[ 88.210000] FEC: MDIO read timeout
[ 88.210000] eth1: could not attach to PHY
[ 88.210000] IP-Config: Failed to open eth1
[ 88.220000] IP-Config: No network devices available.
[ 88.220000] Freeing init memory: 6968K
[...]
starting network interfaces...
ip: RTNETLINK answers: File exists
[ 94.000000] net eth0: PHY already attached
[ 94.010000] eth0: could not attach to PHY
ip: SIOCSIFFLAGS: Device or resource busy
This patch adds phy_detach to clean up if phy_init_hw fails.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Sat, 26 Mar 2011 20:27:24 +0000 (20:27 +0000)]
bridge: mcast snooping, fix length check of snooped MLDv1/2
"len = ntohs(ip6h->payload_len)" does not include the length of the ipv6
header itself, which the rest of this function assumes, though.
This leads to a length check less restrictive as it should be in the
following line for one thing. For another, it very likely leads to an
integer underrun when substracting the offset and therefore to a very
high new value of 'len' due to its unsignedness. This will ultimately
lead to the pskb_trim_rcsum() practically never being called, even in
the cases where it should.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This oops was brought in by the change "block: remove per-queue
plugging" (commit: 7eaceaccab5f40bb). It initializes mapping->a_ops
with a NULL pointer for some pages in nilfs (e.g. btree node pages),
but mm code doesn't NULL pointer checks against mapping->a_ops. (the
check is done for each callback function)
This corrects the aops initialization and fixes the oops.
Ben Hutchings [Mon, 28 Mar 2011 17:12:52 +0000 (17:12 +0000)]
via-ircc: Pass PCI device pointer to dma_{alloc, free}_coherent()
via-ircc has been passing a NULL pointer to DMA allocation functions,
which is completely invalid and results in a BUG on PowerPC. Now
that we always have the device pointer available, pass it in.
Reference: http://bugs.debian.org/619450 Reported-by: Andrew Buckeridge <andrewb@bgc.com.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Andrew Buckeridge <andrewb@bgc.com.au> [against 2.6.32] Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 28 Mar 2011 17:10:43 +0000 (17:10 +0000)]
via-ircc: Use pci_{get, set}_drvdata() instead of static pointer variable
via-ircc still maintains its own array of device pointers in Linux 2.4
style. Worse, it always uses index 0, so it will crash if there are
multiple suitable devices in the system.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Mon, 28 Mar 2011 22:40:53 +0000 (22:40 +0000)]
net: gre: provide multicast mappings for ipv4 and ipv6
My commit 6d55cb91a0020ac0 (gre: fix hard header destination
address checking) broke multicast.
The reason is that ip_gre used to get ipgre_header() calls with
zero destination if we have NOARP or multicast destination. Instead
the actual target was decided at ipgre_tunnel_xmit() time based on
per-protocol dissection.
Instead of allowing the "abuse" of ->header() calls with invalid
destination, this creates multicast mappings for ip_gre. This also
fixes "ip neigh show nud noarp" to display the proper multicast
mappings used by the gre device.
Reported-by: Doug Kehn <rdkehn@yahoo.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Doug Kehn <rdkehn@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clemens Ladisch [Wed, 30 Mar 2011 06:24:00 +0000 (08:24 +0200)]
ALSA: firewire-speakers: fix hang when unplugging a running device
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Balaji G [Tue, 29 Mar 2011 06:20:04 +0000 (06:20 +0000)]
bridge: Fix compilation warning in function br_stp_recalculate_bridge_id()
net/bridge/br_stp_if.c: In function ‘br_stp_recalculate_bridge_id’:
net/bridge/br_stp_if.c:216:3: warning: ‘return’ with no value, in function returning non-void
Signed-off-by: G.Balaji <balajig81@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 30 Mar 2011 06:34:08 +0000 (23:34 -0700)]
net: Fix warnings caused by MAX_SKB_FRAGS change.
After commit a715dea3c8e9ef2771c534e05ee1d36f65987e64 ("net: Always
allocate at least 16 skb frags regardless of page size"), the value
of MAX_SKB_FRAGS can now take on either an "unsigned long" or an
"int" value.
This causes warnings like:
net/packet/af_packet.c: In function ‘tpacket_fill_skb’:
net/packet/af_packet.c:948: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 2 has type ‘int’
Fix by forcing the constant to be unsigned long, otherwise we have
a situation where the type of a system wide constant is variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ryusuke Konishi [Sun, 27 Mar 2011 13:50:49 +0000 (22:50 +0900)]
nilfs2: fix data loss in mmap page write for hole blocks
From the result of a function test of mmap, mmap write to shared pages
turned out to be broken for hole blocks. It doesn't write out filled
blocks and the data will be lost after umount. This is due to a bug
that the target file is not queued for log writer when filling hole
blocks.
Also, nilfs_page_mkwrite function exits normal code path even after
successfully filled hole blocks due to a change of block_page_mkwrite
function; just after nilfs was merged into the mainline,
block_page_mkwrite() started to return VM_FAULT_LOCKED instead of zero
by the patch "mm: close page_mkwrite races" (commit: b827e496c893de0c). The current nilfs_page_mkwrite() is not handling
this value properly.
This corrects nilfs_page_mkwrite() and will resolve the data loss
problem in mmap write.
[This should be applied to every kernel since 2.6.30 but a fix is
needed for 2.6.37 and prior kernels]
Latest irq changes removed the need for this forcing flag, and the
definition - but missed the code that allowed it to be tweaked via
/proc. Delete accessor functions too.
Stephen Rothwell [Tue, 29 Mar 2011 23:55:12 +0000 (10:55 +1100)]
genirq: fix CONFIG_IRQ_EDGE_EOI_HANDLER build
Fixes these errors:
kernel/irq/chip.c: In function 'handle_edge_eoi_irq':
kernel/irq/chip.c:517: warning: label 'out_unlock' defined but not used
kernel/irq/chip.c:503: error: label 'out_eoi' used but not defined
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc/mm: Move the STAB0 location to 0x8000 to make room in low memory
Recent upstream builds with allmodconfig fail due to lack of space
between 0x3000 and 0x6000. We have a hard block at 0x7000 but we can
spare a page by moving the STAB0 from 0x6000 to 0x8000.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sun, 20 Mar 2011 15:28:03 +0000 (15:28 +0000)]
powerpc: Fix accounting of softirq time when idle
commit cf9efce0ce31 (powerpc: Account time using timebase rather
than PURR) used in_irq() to detect if the time was spent in
interrupt processing. This only catches hardirq context so if we
are in softirq context and in the idle loop we end up accounting it
as idle time. If we instead use in_interrupt() we catch both softirq
and hardirq time.
The issue was found when running a network intensive workload. top
showed the following:
Milton Miller [Mon, 21 Mar 2011 11:38:02 +0000 (11:38 +0000)]
powerpc/xics: Fix numberspace mismatch from irq_desc conversion
commit 79f26c268ebad29bd75d078cfc09d3d82b30ccbd (powerpc:
platforms/pseries irq_data conversion) pushed irq_desc down into many
functions, dererencing the descriptor irq field as late as possible.
But it incorrectly passed a linix virtural irq number to RTAS,
resulting in the interrupt not being disabled and possibly
other bad things, such as another interrupt being disabled and/or
a checkstop.
In addition this missed the point of xics_mask_unknown_vec and
the seperation of xics_mask_real_irq from xics_mask_irq. When
xics_mask_unknown_vec is called it's because the hardware delivered an
irq source for which we have no linux irq allocated, and thefore we can
not have an irq_desc allocated.
Revert xics_mask_real_irq to its prior version, naming the argument
hwirq to highlight the difference.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Varun Sethi [Thu, 24 Mar 2011 11:50:26 +0000 (11:50 +0000)]
powerpc/booke: Correct the SPRN_MAS5 definition.
339 is the SPR number for MAS5 documented by Power ISA 2.06, and
implemented by e500mc. It is not yet used anywhere in the kernel,
so nothing should be relying on the wrong number.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Thu, 24 Mar 2011 11:51:19 +0000 (11:51 +0000)]
powerpc: ARCH_PFN_OFFSET should be unsigned long
pfns are unsigned long, but MEMORY_START is phys_addr_t. This leads
to page_to_pfn() returning phys_addr_t, and thus type mismatches in a few
print statements.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by Alsa to mmap buffers allocated with dma_alloc_coherent()
into userspace. We need a special variant to handle machines with
non-coherent DMAs as those buffers have "special" virt addresses and
require non-cachable mappings
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jim Keniston [Fri, 25 Mar 2011 12:47:58 +0000 (12:47 +0000)]
powerpc/nvram: Don't overwrite oops/panic report on normal shutdown
For normal halt, reboot, and poweroff events, refrain from overwriting
the lnx,oops-log partition. Also, don't save the dmesg buffer on an
emergency-restart event if we've already saved it earlier in panic().
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
MISC_DEVICES isn't enabled anymore by default. So all defconfigs that
have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
problem.
This restores those misc devices to the powerpc defconfigs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Uwe Kleine-König Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Thomas Gleixner [Tue, 29 Mar 2011 22:15:49 +0000 (00:15 +0200)]
sh: Fix irq cleanup fallout
I missed that coccinelle does not fix up header files by default.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Paul Mundt <lethal@linux-sh.org> Cc: <lethal@linux-sh.org>
projects / linux-beck.git / log