Santosh Nayak [Mon, 19 Mar 2012 10:27:37 +0000 (07:27 -0300)]
[media] dib0700: Return -EINTR and unlock mutex if locking attempts fails
In 'dib0700_i2c_xfer_new()' and 'dib0700_i2c_xfer_legacy()'
we are taking two locks:
1. i2c_mutex
2. usb_mutex
If attempt to take 'usb_mutex' lock fails then the previously taken
lock 'i2c_mutex' should be unlocked and -EINTR should be returned so
that caller can take appropriate action.
If locking attempt was interrupted by a signal then
we should return -EINTR. At present we are returning '0' for
such scenarios which is wrong.
Replace -EAGAIN by -EINTR as a return type for the the scenario
where locking attempt was interrupted by signal.
Gianluca Gennari [Thu, 15 Mar 2012 16:33:47 +0000 (13:33 -0300)]
[media] cxd2820r: tweak search algorithm behavior
MPIS based STBs running 3.x kernels and the Enigma2 OS are not able to tune
DVB-T channels with the PCTV 290e using the current cxd2820r driver.
DVB-T2 channels instead work properly.
This patch fixes the problem by changing the condition to break out from the
wait lock loop in the "search" function of the cxd2820r demodulator from
FE_HAS_SIGNAL to FE_HAS_LOCK.
As a consequence, the "search" function of the demodulator driver now returns
DVBFE_ALGO_SEARCH_SUCCESS only if the frequency lock is successfully acquired.
This behavior seems consistent with other demodulator drivers (e.g. stv090x,
hd29l2, stv0900, stb0899, mb86a16).
This patch has been successfully tested with DVB-T and DVB-T2 signals,
on both PC and the mipsel STB running Enigma2.
No apparent side effect has been observed on PC applications like Kaffeine.
DVB-C is not available in my country so it's not tested.
Gianluca Gennari [Thu, 15 Mar 2012 16:33:48 +0000 (13:33 -0300)]
[media] em28xx-dvb: enable LNA for cxd2820r in DVB-T mode
Enable the LNA amplifier also for DVB-T (like for DVB-T2 and DVB-C);
this greatly improves reception of weak signals without affecting the reception
of the strong ones.
Experimental data (collected with the mipsel STB) on the weakest frequencies
available in my area:
LNA OFF:
MUX level BER picture
RAI mux 4 72% 32000 corrupted
TIMB 2 75% 14 OK
TVA Vicenza 68% 32000 corrupted
RAI mux 2 78% 14 OK
LNA ON:
MUX level BER picture
RAI mux 4 73% 1500 OK
TIMB 2 76% 0 OK
TVA Vicenza 69% 0 OK
RAI mux 2 79% 0 OK
Moreover, with LNA enabled, the PCTV 290e was able to pick up 2 new frequencies
matching the integrated tuner of my Panasonic G20 TV, which is really good.
As reported by Masanari, this macro is using "KERN_ERR"
instead of "KERN_ERROR". That would lead into a compilation
breakage, if this macro were used somewhere inside the driver.
Instead of fixing the macro, as originally proposed, let's just
remove the dead code.
Ezequiel García [Fri, 24 Feb 2012 14:24:19 +0000 (11:24 -0300)]
[media] staging: easycap: Split audio buffer and urb allocation
When the device is probed, this driver allocates
audio buffers, and audio urbs.
This patch just split this into separate functions,
which helps clearing the currently gigantic probe function.
Ezequiel García [Fri, 24 Feb 2012 14:24:15 +0000 (11:24 -0300)]
[media] staging: easycap: Split buffer and video urb allocation
When the device is probed, this driver allocates
frame buffers, field buffers, isoc buffers and urbs.
This patch just split this into separate functions,
which helps clearing the currently gigantic probe function.
Hans Verkuil [Mon, 7 May 2012 19:53:20 +0000 (16:53 -0300)]
[media] v4l2-event: fix regression with initial event handling
If the V4L2_EVENT_SUB_FL_SEND_INITIAL was set, then the application expects
to receive an initial event of the initial value of the control.
However, commit c53c2549333b340e2662dc64ec81323476b69a97 that added the new
v4l2_subscribed_event_ops introduced a regression: while the code still queued
that initial event the __v4l2_event_queue_fh() function was modified to ignore
such requests if sev->elems was 0 (meaning that the event subscription wasn't
finished yet).
And sev->elems was only set to a non-zero value after the add operation
returned.
This patch fixes this by passing the elems value to the add function. Then the
add function can set it before queuing the initial event.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge remote-tracking branch 'linus/master' into staging/for_v3.5
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
On Mon, 2012-05-07 at 07:45 -0300, Mauro Carvalho Chehab wrote:
> Malcolm,
>
> Em 04-04-2012 20:00, Joe Perches escreveu:
> > Likely these should be && not ||
> >
> > drivers/scsi/FlashPoint.c: if(bit_cnt != 0 || bit_cnt != 8)
>
> > drivers/media/dvb/dvb-usb/it913x.c: if (ret == 0 || ret != -EBUSY || ret != -ETIMEDOUT)
> > drivers/media/dvb/dvb-usb/it913x.c: if (ret == 0 || ret != -EBUSY || ret != -ETIMEDOUT)
>
> Could you please take a look on the above?
Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so
replace it with a NULL pointer when the section gets discarded.
Daniel Drake [Mon, 30 Apr 2012 21:06:27 +0000 (18:06 -0300)]
[media] via-camera: specify XO-1.5 camera clock speed
For the ov7670 camera to return images at the requested frame rate,
it needs to make calculations based on the clock speed, which is
a completely external factor (depends on the wiring of the system).
On the XO-1.5, which is the only known via-camera user, the camera
is clocked at 90MHz.
Pass this information to the ov7670 driver, to fix an issue where
a framerate of 3x the requested amount was being provided.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Mon, 14 May 2012 18:23:37 +0000 (11:23 -0700)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a some fix patches for v3.4, including a regression fix at DVB core"
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca - sonixj: Fix a zero divide in isoc interrupt
[media] media: videobuf2-dma-contig: include header for exported symbols
[media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
[media] media: vb2-memops: Export vb2_get_vma symbol
[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
[media] s5p-fimc: Fix locking in subdev set_crop op
[media] dvb_frontend: fix a regression with DVB-S zig-zag
[media] fintek-cir: change || to &&
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
[media] rc: Postpone ISR registration
[media] marvell-cam: fix an ARM build error
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
Pull networking fixes from David Miller:
"The main purpose of this pull request is to fix up the erroneous
bonding patch I applied last round. I meant to apply v4 of the patch
from Jiri but I applied v3 by accident. Mea culpa.
Also, eagle eyed Dan Carpenter noticed that openvswitch has one of
those "X = alloc(); if (!Y)" mistakes, test the proper pointer
instead."
That commit message suggests that by not taking the core lock for fops
other than unlocked_ioctl all problems relating to AB-BA locking and
mm->mmap_sem are solved. This is not the case.
More work needs to be done by moving the core lock further down into
video_ioctl2. It should only be taken after the copy_from/to_user calls
are done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 16:31:27 +0000 (13:31 -0300)]
[media] av7110: fix v4l2_compliance test issues
Besides the usual inconsistencies in input enumeration there was also a
kernel crash if you tried to poll on a vbi node. The checks for sliced
vbi output vs vbi capture were not complete enough.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The B&W control never worked, and you get the same effect by setting saturation to the
lowest value. So it has been removed. Also fixed some incorrect entries in the input
table. This driver now passes v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 1 May 2012 13:06:40 +0000 (10:06 -0300)]
[media] tda9840: fix setting of the audio mode
You have to first detect the current rxsubchans (mono, stereo or bilingual),
and depending on that you can set the audio mode. It does not automatically
switch when the audio channels change.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:22:58 +0000 (10:22 -0300)]
[media] v4l/dvb: fix compiler warnings
media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 11:04:48 +0000 (08:04 -0300)]
[media] v4l/dvb: fix compiler warnings
media_build/v4l/stb6100.c: In function 'stb6100_read_reg':
media_build/v4l/stb6100.c:161:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx24110.c: In function 'cx24110_read_ucblocks':
media_build/v4l/cx24110.c:515:6: warning: variable 'lastbyer' set but not used [-Wunused-but-set-variable]
media_build/v4l/dib9000.c: In function 'dib9000_mbx_process':
media_build/v4l/dib9000.c:711:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
media_build/v4l/zl10353.c: In function 'zl10353_init':
media_build/v4l/zl10353.c:562:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0297.c: In function 'stv0297_set_frontend':
media_build/v4l/stv0297.c:417:16: warning: variable 'starttime' set but not used [-Wunused-but-set-variable]
media_build/v4l/lgs8gxx.c: In function 'lgs8gxx_set_mode_manual':
media_build/v4l/lgs8gxx.c:265:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/af9013.c: In function 'af9013_statistics_work':
media_build/v4l/af9013.c:517:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_optimize_track':
media_build/v4l/stv090x.c:2845:23: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_algo':
media_build/v4l/stv090x.c:3177:28: warning: variable 'no_signal' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_read_ber':
media_build/v4l/it913x-fe.c:636:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_get_frontend':
media_build/v4l/it913x-fe.c:661:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_set_frontend':
media_build/v4l/it913x-fe.c:694:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/m88rs2000.c: In function 'm88rs2000_set_fec':
media_build/v4l/m88rs2000.c:657:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dst_ca.c: In function 'ca_send_message':
media_build/v4l/dst_ca.c:480:15: warning: variable 'ca_message_header_len' set but not used [-Wunused-but-set-variable]
media_build/v4l/smssdio.c: In function 'smssdio_interrupt':
media_build/v4l/smssdio.c:117:11: warning: variable 'isr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 10:30:48 +0000 (07:30 -0300)]
[media] v4l: fix compiler warnings
media_build/v4l/adv7343.c: In function 'adv7343_setstd':
media_build/v4l/adv7343.c:133:6: warning: variable 'output_idx' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp5150.c: In function 'tvp5150_mbus_fmt':
media_build/v4l/tvp5150.c:833:14: warning: variable 'std' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp7002.c: In function 'tvp7002_query_dv_preset':
media_build/v4l/tvp7002.c:673:18: warning: variable 'device' set but not used [-Wunused-but-set-variable]
media_build/v4l/c-qcam.c: In function 'qc_capture':
media_build/v4l/c-qcam.c:381:33: warning: variable 'bitsperxfer' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'pms_s_std':
media_build/v4l/pms.c:738:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'init_mediavision':
media_build/v4l/pms.c:959:6: warning: variable 'id' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-alsa.c: In function 'cx25821_irq':
media_build/v4l/cx25821-alsa.c:294:6: warning: variable 'audint_count' set but not used [-Wunused-but-set-variable]
media_build/v4l/zr364xx.c: In function 'zr364xx_fillbuff':
media_build/v4l/zr364xx.c:510:25: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 's2255_fillbuff':
media_build/v4l/s2255drv.c:637:23: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 'vidioc_s_fmt_vid_cap':
media_build/v4l/s2255drv.c:990:6: warning: variable 'norm' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-stds.c: In function 'tm6000_set_audio_std':
media_build/v4l/tm6000-stds.c:341:10: warning: variable 'nicam_flag' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'get_next_buf':
media_build/v4l/tm6000-video.c:172:8: warning: variable 'outp' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'copy_streams':
media_build/v4l/tm6000-video.c:214:36: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-input.c: In function 'tm6000_ir_urb_received':
media_build/v4l/tm6000-input.c:171:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_decompress':
media_build/v4l/usbvision-core.c:604:23: warning: variable 'max_pos' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_parse_compress':
media_build/v4l/usbvision-core.c:705:39: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c:705:22: warning: variable 'bytes_per_pixel' set but not used [-Wunused-but-set-variable]
media_build/v4l/zoran_device.c: In function 'write_overlay_mask':
media_build/v4l/zoran_device.c:545:6: warning: variable 'reg' set but not used [-Wunused-but-set-variable]
media_build/v4l/go7007-v4l2.c: In function 'go7007_streamoff':
media_build/v4l/go7007-v4l2.c:79:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:17:35 +0000 (10:17 -0300)]
[media] v4l: fix compiler warnings
media_build/v4l/au0828-video.c: In function 'au0828_irq_callback':
media_build/v4l/au0828-video.c:123:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx23888-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx23888-ir.c:334:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx25840-ir.c:319:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'cx25840_ir_tx_write':
media_build/v4l/cx25840-ir.c:863:21: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c: In function 'snd_em28xx_hw_capture_params':
media_build/v4l/em28xx-audio.c:346:31: warning: variable 'format' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:25: warning: variable 'rate' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:15: warning: variable 'channels' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-control.c: In function 'get_input_lines_info':
media_build/v4l/hdpvr-control.c:98:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-video.c: In function 'hdpvr_try_ctrl':
media_build/v4l/hdpvr-video.c:955:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/saa7134-video.c: In function 'saa7134_s_tuner':
media_build/v4l/saa7134-video.c:2030:6: warning: variable 'rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/sn9c102_core.c: In function 'sn9c102_stream_interrupt':
media_build/v4l/sn9c102_core.c:998:7: warning: variable 'timeout' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Janne Grunau <j@jannau.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 09:26:19 +0000 (06:26 -0300)]
[media] cx25821: fix compiler warnings
media_build/v4l/cx25821-core.c: In function 'cx_i2c_read_print':
media_build/v4l/cx25821-core.c:386:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_dev_setup':
media_build/v4l/cx25821-core.c:899:6: warning: variable 'io_size' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_irq':
media_build/v4l/cx25821-core.c:1321:18: warning: variable 'pci_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-i2c.c: In function 'cx25821_i2c_read':
media_build/v4l/cx25821-i2c.c:365:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_enable_bluefield_output':
media_build/v4l/cx25821-medusa-video.c:39:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_resolution':
media_build/v4l/cx25821-medusa-video.c:435:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_decoderduration':
media_build/v4l/cx25821-medusa-video.c:498:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_dump_video_queue':
media_build/v4l/cx25821-video.c:116:25: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_buffer_prepare':
media_build/v4l/cx25821-video.c:561:20: warning: variable 'line1_offset' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'video_ioctl_set':
media_build/v4l/cx25821-video.c:1834:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream.c: In function 'cx25821_upstream_irq':
media_build/v4l/cx25821-video-upstream.c:641:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream-ch2.c: In function 'cx25821_upstream_irq_ch2':
media_build/v4l/cx25821-video-upstream-ch2.c:591:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-audio-upstream.c: In function 'cx25821_upstream_irq_audio':
media_build/v4l/cx25821-audio-upstream.c:589:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 23 Apr 2012 11:25:20 +0000 (08:25 -0300)]
[media] ivtv/cx18: fix compiler warnings
media_build/v4l/cx18-alsa-main.c: In function 'cx18_alsa_exit':
media_build/v4l/cx18-alsa-main.c:282:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-mailbox.c: In function 'cx18_api_call':
media_build/v4l/cx18-mailbox.c:598:6: warning: variable 'state' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_open':
media_build/v4l/cx18-alsa-pcm.c:156:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_close':
media_build/v4l/cx18-alsa-pcm.c:202:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_hw_params':
media_build/v4l/cx18-alsa-pcm.c:255:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-streams.c: In function 'cx18_stop_v4l2_encode_stream':
media_build/v4l/cx18-streams.c:983:16: warning: variable 'then' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtv-ioctl.c: In function 'ivtv_set_speed':
media_build/v4l/ivtv-ioctl.c:138:22: warning: variable 's' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_init':
media_build/v4l/ivtvfb.c:1286:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_cleanup':
media_build/v4l/ivtvfb.c:1306:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:14:53 +0000 (10:14 -0300)]
[media] cx231xx: fix compiler warnings
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_hw_capture_params’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:527:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:31: warning: variable ‘format’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:25: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:15: warning: variable ‘channels’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_capture_trigger’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:589:6: warning: variable ‘retval’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_isoc_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:331:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_bulk_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:434:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_reset_video_buffer’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:704:7: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_set_mode’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:699:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_ep5_bulkout’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:763:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_isoc_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:800:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_bulk_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:846:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_stop_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1234:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_start_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1254:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_enable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:937:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_disable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:955:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_HH_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1323:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_SC_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1358:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_Setup_AFE_for_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1444:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_Colibri_For_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1504:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_DIF_bandpass’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1559:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_gpio_i2c_write’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:3093:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_initialize_codec’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1098:9: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘vidioc_streamon’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1795:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_isoc_vbi_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:86:25: warning: variable ‘buf’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_irq_vbi_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:313:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 06:30:11 +0000 (03:30 -0300)]
[media] dw2102: fix compile warnings
media_build/v4l/dw2102.c:151:13: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:224:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:279:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:352:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:435:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:499:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2_CID_EXPOSURE_METERING control which allows
to select the light metering mode for automatic exposure as one
of the following modes: spot (small area at the frame center),
center weighted and frame averaged.
[media] m5mols: Add auto and preset white balance control
Replace the V4L2_CID_AUTO_WHITE_BALANCE control with its extended
version - V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE so the white balance
presets feature is exposed to user land.
Acked-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] m5mols: Use proper sensor mode for the controls
The parameters corresponding to the V4L controls can be reconfigured
only in associated M-5MOLS operation mode. Use struct v4l2_ctrl
priv field to assign the working mode to the controls which can be
modified only in certain conditions.
This patch is a prerequisite for the new controls addition. It consolidates
the control handling code, which is moved to m5mols_controls.c and
staticized. The controls initialization is reordered to better reflect
the control clusters and make the diffs smaller when new controls are added.
To make the code easier to follow when more controls is added use separate
set function for each control.
The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.
Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.
Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.
[media] V4L: Add camera image stabilization control
Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Add camera wide dynamic range control
Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Add an extended camera white balance control
This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:
The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
[media] V4L: Add helper function for standard integer menu controls
This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Tested-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.
The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.
On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.
So:
- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
functions.
[media] v4l: v4l2-ctrls: moves the forward declaration of struct file
This fixes the following warning:
In file included from drivers/media/video/v4l2-subdev.c:29:
include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside
parameter list
include/media/v4l2-ctrls.h:501: warning: its scope is only this
definition or declaration, which is probably not what you want
include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside
parameter list
Kartik Mohta [Wed, 2 May 2012 22:19:08 +0000 (19:19 -0300)]
[media] mt9v032: Correct the logic for the auto-exposure setting
The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
Laurent Pinchart [Sat, 10 Mar 2012 00:02:57 +0000 (21:02 -0300)]
[media] mt9p031: Implement black level compensation control
Add four new controls to configure black level compensation (BLC):
- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC
projects / karo-tx-linux.git / log