In current vblank-wait implementation, if we turn off VGA output,
drm_wait_vblank will still wait on the disabled pipe until timeout,
because vblank on the pipe is assumed be enabled. This would cause
slow system response on some system such as moblin.
This patch resolve the issue by adding a drm helper function
drm_vblank_off which explicitly clear vblank_enabled[crtc], wake up
any waiting queue and save last vblank counter before turning off
crtc. It also slightly change drm_vblank_get to ensure that we will
will return immediately if trying to wait on a disabled pipe.
Signed-off-by: Li Peng <peng.li@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied for conflicts with overlay changes] Signed-off-by: Eric Anholt <eric@anholt.net> Cc: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit 0512a9a8e277a9de2820211eef964473b714ae65, we unilaterally zero the
"pwm invert" bit in the fan behavior configuration register. On my PowerBook
G4, this results in the fans going to full speed at low temperature and
shutting off at high temperature because the pwm invert bit is supposed to be
set.
Therefore, record the pwm invert bit at driver load time, and write the bit
into the fan behavior control register. This restores correct behavior on my
PBG4 and should work around the bit being set to the wrong value after
suspend/resume (which is what the original patch was trying to fix). It also
fixes a minor omission where the pwm invert bit correction is NOT performed
when switching into automatic mode.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the rfkill rework in 2.6.31, the driver is always resuming with
the radios disabled.
Change thinkpad-acpi to ask the firmware to resume with the radios in
the last state. This fixes the Bluetooth and WWAN rfkill switches.
Note that it means we respect the firmware's oddities. Should the
user toggle the hardware rfkill switch on and off, it might cause the
radios to resume enabled.
UWB is an unknown quantity since it has nowhere the same level of
firmware support (no control over state storage in NVRAM, for
example), and might need further fixing. Testers welcome.
This change fixes a regression from 2.6.30.
Reported-by: Jerone Young <jerone.young@canonical.com> Reported-by: Ian Molton <ian.molton@collabora.co.uk> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Tested-by: Ian Molton <ian.molton@collabora.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to a report, the R50e wants EC-based brightness control,
even if it uses an Intel GPU. The current driver default was reported
to not work at all.
This bug can be worked around by the "brightness_mode=3" module
parameter.
Change the default of the R50e and R51 2xxx models (which use the same
EC firmware, 1V) to TPACPI_BRGHT_Q_EC, but keep TPACPI_BRGHT_Q_ASK set
for now, as I'd like to get more reports.
Reported-by: Ferenc Wagner <wferi@niif.hu> Tested-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: stable@kernel.org Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I received some bug reports about userspace programs having problems
because after RTM_NEWLINK was received they could not immeidate
access files under /proc/sys/net/ because they had not been
registered yet.
The problem was trivailly fixed by moving the userspace
notification from rtnetlink_event to the end of register_netdevice.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regression caused in 2.6.23 and then despite repeated requests never fixed
or dealt with (Petr promised to sort it in 2008 but seems to have
forgotten).
Enough is enough - remove the problem line that was added. If it upsets
someone they've had two years to deal with it and at the very least it'll
rattle their cage and wake them up.
Ever since jffs2_garbage_collect_metadata() was first half-written in
February 2001, it's been broken on architectures where 'char' is signed.
When garbage collecting a symlink with target length above 127, the payload
length would end up negative, causing interesting and bad things to happen.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PCI .shutdown method so that we can disable the device during
shutdown or reboot. Without this, the reboot doesn't work well on
some platforms.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2124
Tested-by: pablo <pablolm2005@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that any otherwise uninitialised fields of usvc are zero.
This has been obvserved to cause a problem whereby the port of
fwmark services may end up as a non-zero value which causes
scheduling of a destination server to fail for persisitent services.
As observed by Deon van der Merwe <dvdm@truteq.co.za>.
This fix suggested by Julian Anastasov <ja@ssi.bg>.
For good measure also zero udest.
Cc: Deon van der Merwe <dvdm@truteq.co.za> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ext3_write_begin fails after allocating some blocks or
generic_perform_write fails to copy data to write, we truncate blocks already
instantiated beyond i_size. Although these blocks were never inside i_size, we
have to truncate pagecache of these blocks so that corresponding buffers get
unmapped. Otherwise subsequent __block_prepare_write (called because we are
retrying the write) will find the buffers mapped, not call ->get_block, and
thus the page will be backed by already freed blocks leading to filesystem and
data corruption.
Reported-by: James Y Knight <foom@fuhm.net> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In disable sequence, all output ports on PCH have to be disabled
before PCH transcoder, but LVDS port was left always enabled. This
one fixes that by disable LVDS port properly during pipe disable
process, and resolved stability issue seen on Ironlake. Also move
panel fitting disable time just after pipe disable to align with
the spec.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For CRT hotplug detect status, we have four test results as blue
channel only, green channel only, both blue and green channel, and
no channel attached. Origin code only marks both blue and green channel
case as connected, but ignore other possible connected states. This one
trys to detect CRT by checking no channel attached case instead.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit d2d9f2324, the guard for a valid video mode was removed. This
caused the regression:
kernel crash during kms graphic boot on Intel GM4500 platform
https://bugzilla.redhat.com/show_bug.cgi?id=540218
This patches changes the logic slightly not to rely on a coupled
variable, but to just check whether the video_modes is valid before
dereferencing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
[ickle: Actually reference the correct bug report] Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The light sensor disable brightness key and
/sys/class/backlight/ control. There was a lot of report
from users who didn't understand why they couldn't change their
brightness, including:
Now the light sensor is disabled, and if the user want to enable
it, the level should be ok.
The funny thing is that comments where ok, not code.
Cc: stable@kernel.org Cc: Thomas Renninger <trenn@suse.de> Cc: Peter Küppers <peter-mailbox@web.de> Cc: Michael Franzl <michaelfranzl@gmx.at> Cc: Ian Turner <vectro@vectro.org> Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock by skipping the fake
ARB_DISABLE.
The cpu model id on one laptop is 14. If we disable ARB_DISABLE on this box,
the box can't be booted correctly. But if we still enable ARB_DISABLE on this
box, the box can be booted correctly.
So we still use the ARB_DISABLE for the cpu which mode id is less than 0x0f.
http://bugzilla.kernel.org/show_bug.cgi?id=14700
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On platforms where bios handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI and OS
can't touch it.
Unfortunately AP bringup sequence using INIT-SIPI-SIPI clear all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set to masked
(clearing the bios programmed value for APIC_LVTTHMR).
And this leads to kernel take over the thermal monitoring interrupt
on AP's but not on BSP (leaving the bios programmed value only on BSP).
As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.
Fix this by reading the initial value of thermal LVT entry on BSP
and if bios has taken over the control, then program the same value
on all AP's and leave the thermal monitoring interrupt control
on all the logical cpu's to the bios.
Signed-off-by: Yong Wang <yong.y.wang@intel.com> Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Borislav Petkov <borislav.petkov@amd.com> Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.
This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mce_timer must be passed to setup_timer() in all cases, no
matter whether it is going to be actually used. Otherwise, when
the CPU gets brought down, its call to del_timer_sync() will
never return, as the timer won't have a base associated, and
hence lock_timer_base() will loop infinitely.
"ARCH" can be just about anything, so we shouldn't end up
with UTS_MACHINE of "sparc" in a 64-bit kernel build just
because someone set the personality using 'sparc32' or
similar. CONFIG_SPARC64 drives the compilation and
therefore provides the definitive value, not "ARCH".
First, the softirq range check forgets to subtract STACK_BIAS
before comparing with %sp. Next, on failure the wrong label
is jumped to, resulting in a bogus stack being loaded.
Reported-by: Igor Kovalenko <igor.v.kovalenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we are trying to see if a range property entry applies
to a given address, we are overly strict about the type.
We should only allow I/O ranges for I/O addresses, and only allow
CONFIG space ranges for CONFIG space address.
However for MEM ranges, they come in 32-bit and 64-bit flavors.
And a lack of an exact match is OK if the range is 32-bit and
the address is 64-bit. We can assign a 64-bit address properly
into a 32-bit parent range just fine.
So allow it.
Reported-by: Patrick Finnegan <pat@computer-refuge.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be like the other Sun serial drivers otherwise the special handling of
OpenFirmware options and hard-coded overrides for LOM/RSC consoles
will not be handled.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already had some code to match and handle "rsc" named devices on
E250 systems, but we also have to handle 'rsc-console', 'rsc-control',
and 'lom-console'.
Also, in order to get this right regardless of what 'output-device'
happens to be, explicitly pass the UART device node pointer to this
routine.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These device nodes are named "rsc-console" and "rsc-control" rather
than 'serial', but the device_type property is 'serial' so we'll
tip off of that for detection.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Other Sun serial drivers do not do this, and if we keep it this way
it ends up registering all serial devices as consoles rather than
just the one which we explicitly register via sunserial_console_match()
which uses add_preferred_console().
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was the cause of various boot failures on V480, V880, etc.
systems.
Kernel image memory was being overwritten because the vmemmap[]
array was being sized to small. So if you had physical memory
addresses past a certain point, the early bootup would spam
all over variables in the kernel data section.
The vmemmap mappings map page structs, not page struct pointers.
And that was the key thinko in the macro definition.
This was fixable thanks to the help, reports, and tireless patience
of Hermann Lauer.
Reported-by: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case register_netdevice() returns an error, and a new vlan_group
was allocated and inserted in vlan_group_hash[] we call
vlan_group_free() without deleting group from hash table. Future
lookups can give infinite loops or crashes.
We must delete the vlan_group using RCU safe procedure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a null pointer dereference BUG() if ethtool is used on
an smsc9420 interface while it is down, because the phy_dev is only
allocated while the interface is up.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
smc91x.h defines SMC_IRQ_FLAGS to be -1 when it wants the interrupt
flags to be taken from the resource structure. However, d280ead
changed this to checking for non-zero resource flags.
Unfortunately, this means that on some platforms, we end up passing
'-1' to request_irq rather than the desired result. Combine the two
conditions into one so that the IRQ flags are taken from the resource
if either SMC_IRQ_FLAGS is -1 or the resource flags specify an
interrupt trigger.
This restores network on at least the Versatile platform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In dev_change_name() an err variable is used for storing the original
call_netdevice_notifiers() errno (negative) and testing for a rollback
error later, but the test for non-zero is wrong, because the err might
have positive value as well - from dev_alloc_name(). It means the
rollback for a netdevice with a number > 0 will never happen. (The err
test is reordered btw. to make it more readable.)
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a large packet gets reassembled by ip_defrag(), the head skb
accounts for all the fragments in skb->truesize. If this packet is
refragmented again, skb->truesize is not re-adjusted to reflect only
the head size since its not owned by a socket. If the head fragment
then gets recycled and reused for another received fragment, it might
exceed the defragmentation limits due to its large truesize value.
skb_recycle_check() explicitly checks for linear skbs, so any recycled
skb should reflect its true size in skb->truesize. Change ip_fragment()
to also adjust the truesize value of skbs not owned by a socket.
Reported-and-tested-by: Ben Menchaca <ben@bigfootnetworks.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we've merged skb's with page frags, and subsequently receive
a trailer skb (< MSS) that is not completely non-linear (this can
occur on Intel NICs if the packet size falls below the threshold),
GRO ends up producing an illegal GSO skb with a frag_list.
This is harmless unless the skb is then forwarded through an
interface that requires software GSO, whereupon the GSO code
will BUG.
This patch detects this case in GRO and avoids merging the
trailer skb.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.
Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
It seems that set_bit() on line 1509 always writes one bit off.
The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.
It seems that this problem affects all kernel versions since commit 725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.
Reported-by: Andreas Lohre <alohre@gmail.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix checking of the currently programmed UDMA mode.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, ide_cmd_ioctl when invoked for setting DMA transfer mode calls
ide_find_dma_mode with requested mode as XFER_UDMA_6. This prevents setting DMA
mode to any other value than the default (maximum) supported by the device (or
UDMA6, if supported) irrespective of the actual requested transfer mode and
returns error.
For example, setting mode to UDMA2 using hdparm, where UDMA4 is the default
transfer mode gives following error:
# ./hdparm -d1 -Xudma2 /dev/hda
/dev/hda:hda: UDMA/66 mode selected
setting using_dma to 1 (on)
hda: UDMA/66 mode selected
setting xfermode to 66 (UltraDMA mode2)
HDIO_DRIVE_CMD(setxfermode) failed: Invalid argument
using_dma = 1 (on)
This patch fixes the issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Tested-by: Frans Pop <elendil@planet.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN
Reading the IIR clears some oustanding interrupts so it is not safe.
Instead, simply transmit immediately if the buffer is empty without
regard to IIR.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Jiri Kosina <jkosina@suse.cz> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
e821ea70f3b4873b50056a1e0f74befed1014c09 introduced a bug by copying
some 64-bit originated code as-is to be used by both 32 and 64-bit
but this code contains a 64-bit ony "cmpdi" instruction.
This changes it to cmpwi, which is fine since VRSAVE can only contains
a 32-bit value anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most callers of pmd_none_or_clear_bad() check whether the target page is
in a hugepage or not, but walk_page_range() do not check it. So if we
read /proc/pid/pagemap for the hugepage on x86 machine, the hugepage
memory is leaked as shown below. This patch fixes it.
Details
=======
My test program (leak_pagemap) works as follows:
- creat() and mmap() a file on hugetlbfs (file size is 200MB == 100 hugepages,)
- read()/write() something on it,
- call page-types with option -p (walk around the page tables),
- munmap() and unlink() the file on hugetlbfs
Most callers of pmd_none_or_clear_bad() check whether the target page is
in a hugepage or not, but mincore() and walk_page_range() do not check it.
So if we use mincore() on a hugepage on x86 machine, the hugepage memory
is leaked as shown below. This patch fixes it by extending mincore()
system call to support hugepages.
Details
=======
My test program (leak_mincore) works as follows:
- creat() and mmap() a file on hugetlbfs (file size is 200MB == 100 hugepages,)
- read()/write() something on it,
- call mincore() for first ten pages and printf() the values of *vec
- munmap() and unlink() the file on hugetlbfs
Return values in *vec from mincore() are set to 0, while the hugepage
should be in memory, and 1 hugepage is still accounted as used while
there is no file on hugetlbfs.
On a 32-bit machine, BIT() macro does not give the required
bit value if the bit is mroe than 31. In ieee802_11_parse_elems_crc(),
BIT() is suppossed to get the bit value more than 31 (42 (id of ERP_INFO_IE),
37 (CHANNEL_SWITCH_IE), (42), 32 (POWER_CONSTRAINT_IE), 45 (HT_CAP_IE),
61 (HT_INFO_IE)). As we do not get the required bit value for the above
IEs, crc over these IEs are never calculated, so any dynamic change in these
IEs after the association is not really handled on 32-bit platforms.
This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a multi-node x3950M2 system, there's a slight oddity in the
PCI device tree for all secondary nodes:
30:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
\-33:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01)
\-34:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04)
...as compared to the primary node:
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
\-01:00.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
03:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01)
\-04:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04)
In both nodes, the LSI RAID controller hangs off a CalIOC2
device, but on the secondary nodes, the BIOS hides the VGA
device and substitutes the device tree ending with the disk
controller.
It would seem that Calgary devices don't necessarily appear at
the top of the PCI tree, which means that the current code to
find the Calgary IOMMU that goes with a particular device is
buggy.
Rather than walk all the way to the top of the PCI
device tree and try to match bus number with Calgary descriptor,
the code needs to examine each parent of the particular device;
if it encounters a Calgary with a matching bus number, simply
use that.
Otherwise, we BUG() when the bus number of the Calgary doesn't
match the bus number of whatever's at the top of the device tree.
Extra note: This patch appears to work correctly for the x3950
that came before the x3950 M2.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Muli Ben-Yehuda <muli@il.ibm.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Joerg Roedel <joerg.roedel@amd.com> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Jon D. Mason <jdmason@kudzu.us> Cc: Corinna Schultz <coschult@us.ibm.com>
LKML-Reference: <20091202230556.GG10295@tux1.beaverton.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug reporter noted their system with an ASUS P4S800 motherboard would
hang when rebooting unless reboot=b was specified. Their dmidecode
didn't contain descriptive System Information for Manufacturer or
Product Name, so I used their Base Board Information to create a
reboot quirk patch. The bug reporter confirmed this patch resolves
the reboot hang.
Handle 0x0001, DMI type 1, 25 bytes
System Information
Manufacturer: System Manufacturer
Product Name: System Name
Version: System Version
Serial Number: SYS-1234567890
UUID: E0BFCD8B-7948-D911-A953-E486B4EEB67F
Wake-up Type: Power Switch
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: ASUSTeK Computer INC.
Product Name: P4S800
Version: REV 1.xx
Serial Number: xxxxxxxxxxx
BugLink: http://bugs.launchpad.net/bugs/366682
ASUS P4S800 will hang when rebooting unless reboot=b is specified.
Add a quirk to reboot through the bios.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
LKML-Reference: <1259972107.4629.275.camel@emiko> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some devices the ACPI table may define unity map
requirements which must me met when the IOMMU is enabled. So
we need to attach devices to their domains as early as
possible so that these mappings are in place when needed.
This patch assigns the domains right after they are
allocated. Otherwise this can result in I/O page faults
before a driver binds to a device and BIOS is still using
it.
usb_bulk_msg() transfers only bytes up to the maximum packet size.
It must be repeated by the usbtmc driver until all bytes of a TMC message
are transfered.
Without this patch, ETIMEDOUT is reported when writing TMC messages
larger than the maximum USB bulk size and the transfer remains incomplete.
The user will notice that the device hangs and must be reset by either closing
the application or pulling the plug.
Signed-off-by: Andre Herms <andre.herms@tec-venture.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1311) fixes a problem in usb-storage: Some devices are
pretty broken when it comes to reporting sense data. The information
they send back indicates that they have more than 18 bytes of sense
data available, but when the system asks for more than 18 they fail or
hang. The symptom is that probing fails with multiple resets.
The patch adds a new BAD_SENSE flag to indicate that usb-storage
should never ask for more than 18 bytes of sense data. The flag can
be set in an unusual_devs entry or via the "quirks=" module parameter,
and it is set automatically whenever a REQUEST SENSE command for more
than 18 bytes fails or times out.
An unusual_devs entry is added for the Agfa photo frame, which uses a
Prolific chip having this bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Daniel Kukula <daniel.kuku@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be switched
to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
"The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely."
So, the majority of the cases of unhandled IRQs is still unfixed...
USB drivers that create character devices call usb_register_dev in their
probe function. This associates the usb_interface device with that minor
number and creates the character device and announces it to the world.
However, the driver's probe function is called before the new
usb_interface is added to the driver's klist_devices.
This is a problem because userspace will respond to the character device
creation announcement by opening the character device. The driver's open
function will the call usb_find_interface to find the usb_interface
associated with that minor number. usb_find_interface will walk the
driver's list of devices and find the usb_interface with the matching
minor number.
Because the announcement happens before the usb_interface is added to the
driver's klist_devices, a race condition exists. A straightforward fix
is to walk the list of devices on usb_bus_type instead since the device
is added to that list before the announcement occurs.
bus_find_device calls get_device to bump the reference count on the found
device. It is arguable that the reference count should be dropped by the
caller of usb_find_interface instead of usb_find_interface, however,
the current users of usb_find_interface do not expect this.
The original version of this patch only matched against minor number
instead of driver and minor number. This version matches against both.
The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes. Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...
However, the drivers added some breakage of their own too: the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...
Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A write intent bitmap can be removed from an array while the
array is active.
When this happens, all IO is suspended and flushed before the
bitmap is removed.
However it is possible that bitmap_daemon_work is still running to
clear old bits from the bitmap. If it is, it can dereference the
bitmap after it has been freed.
So introduce a new mutex to protect bitmap_daemon_work and get it
before destroying a bitmap.
This patch moves s390 processor status word into the base kvm_run
struct and keeps it up-to date on all userspace exits.
The userspace ABI is broken by this, however there are no applications
in the wild using this. A capability check is provided so users can
verify the updated API exists.
If there is a failed journal checksum, don't reset the journal. This
allows for userspace programs to decide how to recover from this
situation. It may be that ignoring the journal checksum failure might
be a better way of recovering the file system. Once we add per-block
checksums, we can definitely do better. Until then, a system
administrator can try backing up the file system image (or taking a
snapshot) and and trying to determine experimentally whether ignoring
the checksum failure or aborting the journal replay results in less
data loss.
A specially-crafted Hierarchical File System (HFS) filesystem could cause
a buffer overflow to occur in a process's kernel stack during a memcpy()
call within the hfs_bnode_read() function (at fs/hfs/bnode.c:24). The
attacker can provide the source buffer and length, and the destination
buffer is a local variable of a fixed length. This local variable (passed
as "&entry" from fs/hfs/dir.c:112 and allocated on line 60) is stored in
the stack frame of hfs_bnode_read()'s caller, which is hfs_readdir().
Because the hfs_readdir() function executes upon any attempt to read a
directory on the filesystem, it gets called whenever a user attempts to
inspect any filesystem contents.
[amwang@redhat.com: modify this patch and fix coding style problems] Signed-off-by: WANG Cong <amwang@redhat.com> Cc: Eugene Teo <eteo@redhat.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Dave Anderson <anderson@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devpts_get_tty() assumes that the inode passed in is associated with a valid
pty. But if the only reference to the pty is via a bind-mount, the inode
passed to devpts_get_tty() while valid, would refer to a pty that no longer
exists.
With a lot of debug effort, Grzegorz Nosek developed a small program (see
below) to reproduce a crash on recent kernels. This crash is a regression
introduced by the commit:
Setting fops and private data outside of the mutex at debugfs file
creation introduces a race where the files can be opened with the wrong
file operations and private data. It is easy to trigger with a process
waiting on file creation notification.
commit d8e180dcd5bbbab9cd3ff2e779efcf70692ef541 "bsdacct: switch
credentials for writing to the accounting file" introduced credential
switching during final acct data collecting. However, uid/gid pair
continued to be collected from current which became credentials of who
created acct file, not who exits.
Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.
If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.
If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.
Tested on an AR5414
Cc: jirislaby@gmail.com Cc: akpm@linux-foundation.org Cc: rjw@sisk.pl Cc: me@bobcopeland.com Cc: david.quan@atheros.com Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a holdover from earlier code when we used to set
the power limit to '0' after a reset to configure the
default transmit power, ath5k interprets txpower=0 as
12.5 dBm. Fix that by just passing 0 through.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567
Reported-by: Daniel Folkers <daniel.folkers@task24.nl> Tested-by: Daniel Folkers <daniel.folkers@task24.nl> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The timer stop callback can be called from snd_timer_interrupt(), which
is called from the hrtimer callback. Since hrtimer_cancel() waits for
the callback completion, this eventually results in a lock-up.
This patch fixes the problem by just toggling a flag at stop callback
and call hrtimer_cancel() later.
Queueing to receive an ISO packet with a payload length of zero
silently does nothing in dualbuffer mode, and crashes the kernel in
packet-per-buffer mode. Return an error in dualbuffer mode, because
the DMA controller won't let us do what we want, and work correctly in
packet-per-buffer mode.
Signed-off-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1312) fixes a minor bug in usb-storage. The
fill_inquiry() routine neglects to pre-load the inquiry data buffer
with spaces. As a result, if the vendor name is shorter than 8
characters or the product name is shorter than 16, the remainder will
be filled with garbage.
The patch also removes some unnecessary calls to strlen().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All architectures in the kernel increment/decrement the stack pointer
before storing values on the stack.
On architectures which have the stack grow down sas_ss_sp == sp is not
on the alternate signal stack while sas_ss_sp + sas_ss_size == sp is
on the alternate signal stack.
On architectures which have the stack grow up sas_ss_sp == sp is on
the alternate signal stack while sas_ss_sp + sas_ss_size == sp is not
on the alternate signal stack.
The current implementation fails for architectures which have the
stack grow down on the corner case where sas_ss_sp == sp.This was
reported as Debian bug #544905 on AMD64.
Simplified test case: http://download.breakpoint.cc/tc-sig-stack.c
The test case creates the following stack scenario:
0xn0300 stack top
0xn0200 alt stack pointer top (when switching to alt stack)
0xn01ff alt stack end
0xn0100 alt stack start == stack pointer
If the signal is sent the stack pointer is pointing to the base
address of the alt stack and the kernel erroneously decides that it
has already switched to the alternate stack because of the current
check for "sp - sas_ss_sp < sas_ss_size"
On parisc (stack grows up) the scenario would be:
0xn0200 stack pointer
0xn01ff alt stack end
0xn0100 alt stack start = alt stack pointer base
(when switching to alt stack)
0xn0000 stack base
This is handled correctly by the current implementation.
[ tglx: Modified for archs which have the stack grow up (parisc) which
would fail with the correct implementation for stack grows
down. Added a check for sp >= current->sas_ss_sp which is
strictly not necessary but makes the code symetric for both
variants ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: Kyle McMartin <kyle@mcmartin.ca>
LKML-Reference: <20091025143758.GA6653@Chamillionaire.breakpoint.cc> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of our virtual SCSI hosts don't have a proper bus parent at the
top, which can be a problem for doing DMA on them
This patch makes the host device cache a pointer to the physical bus
device and provides an extra API for setting it (the normal API picks
it up from the parent). This patch also modifies the qla2xxx and lpfc
vport logic to use the new DMA host setting API.
Acked-By: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/scsi/osd_protocol.h uses ALIGN() without an #include
<linux/kernel.h>, leading to:
| include/scsi/osd_protocol.h:362: error: implicit declaration of function 'ALIGN'
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes three problems in the handling of the
EXT4_IOC_MOVE_EXT ioctl:
1. In current EXT4_IOC_MOVE_EXT, there are read access mode checks for
original and donor files, but they allow the illegal write access to
donor file, since donor file is overwritten by original file data. To
fix this problem, change access mode checks of original (r->r/w) and
donor (r->w) files.
2. Disallow the use of donor files that have a setuid or setgid bits.
3. Call mnt_want_write() and mnt_drop_write() before and after
ext4_move_extents() calling to get write access to a mount.
We cannot rely on buffer dirty bits during fsync because pdflush can come
before fsync is called and clear dirty bits without forcing a transaction
commit. What we do is that we track which transaction has last changed
the inode and which transaction last changed allocation and force it to
disk on fsync.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Inside ->setattr() call both ATTR_UID and ATTR_GID may be valid
This means that we may end-up with transferring all quotas. Add
we have to reserve QUOTA_DEL_BLOCKS for all quotas, as we do in
case of QUOTA_INIT_BLOCKS.
Currently all quota block reservation macros contains hard-coded "2"
aka MAXQUOTAS value. This is no good because in some places it is not
obvious to understand what does this digit represent. Let's introduce
new macro with self descriptive name.
projects / karo-tx-linux.git / log