Updating the driver to set the correct boundary values in SGE_CONTROL to
32B.
Also, need to take care of this fl alignment change when calculating the
next packet offset.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 23 Dec 2015 12:23:17 +0000 (13:23 +0100)]
dsa: mv88e6xxx: Add Second back of statistics
The 6320 family of switch chips has a second bank for statistics, but
is missing three statistics in the port registers. Generalise and
extend the code:
* adding a field to the statistics table indicating the bank/register
set where each statistics is.
* add a function indicating if an individual statistics
is available on this device
* calculate at run time the sset_count.
* return strings based on the available statistics of the device
* return statistics based on the available statistics of the device
* Add support for reading from the second bank.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Dec 2015 03:06:39 +0000 (22:06 -0500)]
Merge branch 'sfc-vf'
Bert Kenward says:
====================
sfc: additional virtual function support
This introduces the client side of a mechanism to defer authorisation of
operations, for example multicast subscription. Although primarily aimed at
SRIOV VFs this can also apply to unprivileged PFs.
Also handle reboot ordering corner cases better and reduce the level of some
logging.
v2: remove #ifdef DEBUG around new WARN_ON in mcdi.c.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Wed, 23 Dec 2015 08:58:15 +0000 (08:58 +0000)]
sfc: Downgrade or remove some error messages
Depending on configuration the NIC may return errors for unprivileged
functions and/or VFs. Where these are expected and handled, reduce the
level of any output.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Wed, 23 Dec 2015 08:57:36 +0000 (08:57 +0000)]
sfc: Make failed filter removal less noisy
There are situations - mostly reset related - where our view of the
filter table differs from the hardware. In this case we may try and
remove filters that aren't actually installed. This isn't that
interesting in most situations, so downgrade the logging.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Wed, 23 Dec 2015 08:57:18 +0000 (08:57 +0000)]
sfc: Handle MCDI proxy authorisation
For unprivileged functions operations can be authorised by an admin
function. Extra steps are introduced to the MCDI protocol in this
situation - the initial response from the MCDI tells us that the
operation has been deferred, and we must retry when told. We then
receive an event telling us to retry.
Note that this provides only the functionality for the unprivileged
functions, not the handling of the administrative side.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Wed, 23 Dec 2015 08:56:40 +0000 (08:56 +0000)]
sfc: Retry MCDI after NO_EVB_PORT error on a VF
After reboot the vswitch configuration from the PF may not be
complete before the VF attempts to restore filters. In that
case we see NO_EVB_PORT errors from the MC. Retry up to a time
limit or until a different result is seen.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Dec 2015 17:05:53 +0000 (12:05 -0500)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
Trivial enhancements for cxgb4
This series adds a debug message if adapter isn't inserted in right PCI
slot. Changes naming conventions for iSCSI rx queues, use node info while
allocating rx queue and use napi_complete_done() api in napi handler.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2: Dropped 'dcb_info' debug entry patch, since the same can be achieved
using lldp tool.
Based on review comments by Or Gerlitz <gerlitz.or@gmail.com> and
David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All the upper level protocols like rdma, iscsi have their own offload rx
queues, so instead of using the generic naming convention be specific
while naming them. Improves code readability
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Warn if device doesn't have enough PCI bandwidth
Check if the device get enough bandwidth from the entire PCI chain to
satisfy its capabilities. This patch determines the PCIe device's
bandwidth capabilities by reading its PCIe Link Capabilities registers
and then call the pcie_get_minimum_link function to ensure that the
adapter is hooked into a slot which is capable of providing the
necessary bandwidth capabilities.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Dec 2015 22:03:06 +0000 (17:03 -0500)]
Merge branch 'bindtodevice_tw_rst'
Florian Westphal says:
====================
tcp: honour SO_BINDTODEVICE for TW_RST case too
This is V2, this time as a small series since I followed Erics advice
to split this into smaller chunks, I hope this makes it easier to
review.
First patch adds inet_sk_transparent helper.
Second patch contains an if/else swap that I split from the
original TW_RST v1 one.
Third patch is the actual change without the superfluous sock_net change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Dec 2015 20:29:26 +0000 (21:29 +0100)]
tcp: honour SO_BINDTODEVICE for TW_RST case too
Hannes points out that when we generate tcp reset for timewait sockets we
pretend we found no socket and pass NULL sk to tcp_vX_send_reset().
Make it cope with inet tw sockets and then provide tw sk.
This makes RSTs appear on correct interface when SO_BINDTODEVICE is used.
Packetdrill test case:
// want default route to be used, we rely on BINDTODEVICE
`ip route del 192.0.2.0/24 via 192.168.0.2 dev tun0`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
// test case still works due to BINDTODEVICE
0.001 setsockopt(3, SOL_SOCKET, SO_BINDTODEVICE, "tun0", 4) = 0
0.100...0.200 connect(3, ..., ...) = 0
// more data while in FIN_WAIT2, expect RST
1.300 < P. 1:1001(1000) ack 1 win 46
// fails without this change -- default route is used
1.301 > R 1:1(0) win 0
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the two branches: check if we have a socket first, then
fall back to a listener lookup if we saw a md5 option (hash_location).
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Dec 2015 20:29:24 +0000 (21:29 +0100)]
net: add inet_sk_transparent() helper
Avoids cluttering tcp_v4_send_reset when followup patch extends
it to deal with timewait sockets.
Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 22 Dec 2015 08:43:07 +0000 (09:43 +0100)]
mlxsw: core: Use devm_kzalloc to allocate mlxsw_hwmon structure
KASan reported use-after-free for the hwmon structure. So fix this by
using devm_kzalloc and let the core take care about freeing the memory
during device dettach.
Reported-by: Ido Schimmel <idosch@mellanox.com> Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Mon, 21 Dec 2015 15:03:44 +0000 (00:03 +0900)]
net: tcp: deal with listen sockets properly in tcp_abort.
When closing a listen socket, tcp_abort currently calls
tcp_done without clearing the request queue. If the socket has a
child socket that is established but not yet accepted, the child
socket is then left without a parent, causing a leak.
Fix this by setting the socket state to TCP_CLOSE and calling
inet_csk_listen_stop with the socket lock held, like tcp_close
does.
Tested using net_test. With this patch, calling SOCK_DESTROY on a
listen socket that has an established but not yet accepted child
socket results in the parent and the child being closed, such
that they no longer appear in sock_diag dumps.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like an attempt to use CPU notifier here which was never
completed. Nobody tried to wire it up completely since 2k9. So I unwind
this code and get rid of everything not required. Oh look! 19 lines were
removed while code still does the same thing.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Tested-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Dec 2015 19:49:03 +0000 (14:49 -0500)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2015-12-22
This series contains updates to fm10k only.
Bruce cleans up the initialization of fm10k_workqueue at the global level,
which fixes a checkpatch.pl error. Made several other cleanups of the
driver, like making structures that do not change constant, remove unused
code, cleanup code comments and use boolean states true/false instead of
an integer since a bool is all that is needed.
Jacob fixed the TLV format for little endian structures which are 4 byte
aligned copy, so add an additional __aligned(4) and __packed to ensure
that these structures are actually 4 byte aligned and packed correctly.
Updated the driver to use ether_addr_equal() instead of memcmp() to
compare MAC addresses.
Alex Duyck cleans up the exception handling so all of the paths result in
a similar state if we fail. Specifically the driver will now unload the
mailbox interrupt, free the queue vectors and MSI-X, and then detach the
interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 9 Dec 2015 01:20:49 +0000 (17:20 -0800)]
fm10k: IS_ENABLED() is not appropriate for boolean kconfig option
Tri-states need 'if IS_ENABLED()', booleans should use 'ifdef'.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 9 Dec 2015 01:20:44 +0000 (17:20 -0800)]
fm10k: cleanup mailbox code comments etc
Cleanup a number of issues with function header comments, lower-case
acronyms (i.e. FIFO, TLV), duplicate comments and a stubbed-out header
comment for fm10k_sm_mbx_init.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 8 Dec 2015 23:51:11 +0000 (15:51 -0800)]
fm10k: use true/false for boolean get_host_state
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 8 Dec 2015 23:51:04 +0000 (15:51 -0800)]
fm10k: remove unused struct element
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 8 Dec 2015 23:50:39 +0000 (15:50 -0800)]
fm10k: constify fm10k_mac_ops, fm10k_iov_ops and fm10k_info structures
These structures never change so declare them as const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 8 Dec 2015 23:50:34 +0000 (15:50 -0800)]
fm10k: address operator not needed when declaring function pointers
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 16 Nov 2015 23:33:34 +0000 (15:33 -0800)]
fm10k: use ether_addr_equal instead of memcmp
When comparing MAC addresses, use ether_addr_equal instead of memcmp to
ETH_ALEN length. Found and replaced using the following sed:
sed -e 's/memcmp\x28\(.*\), ETH_ALEN\x29/!ether_addr_equal\x28\1\x29/'
Reported-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 10 Nov 2015 17:40:30 +0000 (09:40 -0800)]
fm10k: Cleanup exception handling for changing queues
This patch is meant to cleanup the exception handling for the paths where
we reset the interrupts and then reconfigure them. In all of these paths
we had very different levels of exception handling. I have updated the
driver so that all of the paths should result in a similar state if we
fail.
Specifically the driver will now unload the mailbox interrupt, free the
queue vectors and MSI-X, and then detach the interface.
In addition for any of the PCIe related resets I have added a check with
the hw_ready function to just make sure the registers are in a readable
state prior to reopening the interface.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 9 Nov 2015 22:04:08 +0000 (14:04 -0800)]
fm10k: correctly pack TLV structures and explain reasoning
The TLV format for little endian structures is actually 4 byte aligned
copy. To this end, we need to add an additional __aligned(4) marker
along with __packed to ensure that these structures are actually 4 byte
aligned and packed correctly. Use of just __packed will not work as this
will result in 1byte alignment which is incorrect. Add a comment
explaining the reasoning behind why these structures need the special
treatment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 3 Nov 2015 19:35:02 +0000 (11:35 -0800)]
fm10k: don't initialize fm10k_workqueue at global level
Cleans up checkpatch GLOBAL_INITIALIZERS error
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Arnd Bergmann [Fri, 18 Dec 2015 14:18:08 +0000 (15:18 +0100)]
netcp: fix regression in receive processing
A cleanup patch I did was unfortunately wrong and introduced
multiple serious bugs in the netcp rx processing, as indicated
by these correct gcc warnings:
drivers/net/ethernet/ti/netcp_core.c:776:14: warning: 'buf_ptr' may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/ti/netcp_core.c:687:14: warning: 'ptr' may be used uninitialized in this function [-Wuninitialized]
I have checked the patch once more and found that a call to
get_pkt_info() accidentally got removed in netcp_free_rx_desc_chain,
and netcp_process_one_rx_packet no longer retrieved the correct
buffer length. This patch should fix all the known problems,
but I did not test on real hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 899077791403 ("netcp: try to reduce type confusion in descriptors") Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is possible for an external system to send oversize packets
at anytime, it is best for driver not to print a message and spam
the log (potential external DoS).
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=109471 Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Dec 2015 00:14:11 +0000 (16:14 -0800)]
tcp: diag: add support for request sockets to tcp_abort()
Adding support for SYN_RECV request sockets to tcp_abort()
is quite easy after our tcp listener rewrite.
Note that we also need to better handle listeners, or we might
leak not yet accepted children, because of a missing
inet_csk_listen_stop() call.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Tested-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Dec 2015 21:04:52 +0000 (16:04 -0500)]
Merge branch 'bpf-misc-updates'
Daniel Borkmann says:
====================
Misc BPF updates
This series contains a couple of misc updates to the BPF code, besides
others a new helper bpf_skb_load_bytes(), moving clearing of A/X to the
classic converter, etc. Please see individual patches for details.
Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 17 Dec 2015 22:51:57 +0000 (23:51 +0100)]
bpf, test: add couple of test cases
Add couple of test cases for interpreter but also JITs, f.e. to test that
when imm32 moves are being done, upper 32bits of the regs are being zero
extended.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 17 Dec 2015 22:51:56 +0000 (23:51 +0100)]
bpf, x86: detect/optimize loading 0 immediates
When sometimes structs or variables need to be initialized/'memset' to 0 in
an eBPF C program, the x86 BPF JIT converts this to use immediates. We can
however save a couple of bytes (f.e. even up to 7 bytes on a single emmission
of BPF_LD | BPF_IMM | BPF_DW) in the image by detecting such case and use xor
on the dst register instead.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 17 Dec 2015 22:51:55 +0000 (23:51 +0100)]
bpf: fix misleading comment in bpf_convert_filter
Comment says "User BPF's register A is mapped to our BPF register 6",
which is actually wrong as the mapping is on register 0. This can
already be inferred from the code itself. So just remove it before
someone makes assumptions based on that. Only code tells truth. ;)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 17 Dec 2015 22:51:54 +0000 (23:51 +0100)]
bpf: move clearing of A/X into classic to eBPF migration prologue
Back in the days where eBPF (or back then "internal BPF" ;->) was not
exposed to user space, and only the classic BPF programs internally
translated into eBPF programs, we missed the fact that for classic BPF
A and X needed to be cleared. It was fixed back then via 83d5b7ef99c9
("net: filter: initialize A and X registers"), and thus classic BPF
specifics were added to the eBPF interpreter core to work around it.
This added some confusion for JIT developers later on that take the
eBPF interpreter code as an example for deriving their JIT. F.e. in f75298f5c3fe ("s390/bpf: clear correct BPF accumulator register"), at
least X could leak stack memory. Furthermore, since this is only needed
for classic BPF translations and not for eBPF (verifier takes care
that read access to regs cannot be done uninitialized), more complexity
is added to JITs as they need to determine whether they deal with
migrations or native eBPF where they can just omit clearing A/X in
their prologue and thus reduce image size a bit, see f.e. cde66c2d88da
("s390/bpf: Only clear A and X for converted BPF programs"). In other
cases (x86, arm64), A and X is being cleared in the prologue also for
eBPF case, which is unnecessary.
Lets move this into the BPF migration in bpf_convert_filter() where it
actually belongs as long as the number of eBPF JITs are still few. It
can thus be done generically; allowing us to remove the quirk from
__bpf_prog_run() and to slightly reduce JIT image size in case of eBPF,
while reducing code duplication on this matter in current(/future) eBPF
JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Zi Shen Lim <zlim.lnx@gmail.com> Cc: Yang Shi <yang.shi@linaro.org> Acked-by: Yang Shi <yang.shi@linaro.org> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 17 Dec 2015 22:51:53 +0000 (23:51 +0100)]
bpf: add bpf_skb_load_bytes helper
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf023 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for net-next
The following patchset contains the first batch of Netfilter updates for
the upcoming 4.5 kernel. This batch contains userspace netfilter header
compilation fixes, support for packet mangling in nf_tables, the new
tracing infrastructure for nf_tables and cgroup2 support for iptables.
More specifically, they are:
1) Two patches to include dependencies in our netfilter userspace
headers to resolve compilation problems, from Mikko Rapeli.
2) Four comestic cleanup patches for the ebtables codebase, from Ian Morris.
3) Remove duplicate include in the netfilter reject infrastructure,
from Stephen Hemminger.
4) Two patches to simplify the netfilter defragmentation code for IPv6,
patch from Florian Westphal.
5) Fix root ownership of /proc/net netfilter for unpriviledged net
namespaces, from Philip Whineray.
6) Get rid of unused fields in struct nft_pktinfo, from Florian Westphal.
7) Add mangling support to our nf_tables payload expression, from
Patrick McHardy.
8) Introduce a new netlink-based tracing infrastructure for nf_tables,
from Florian Westphal.
9) Change setter functions in nfnetlink_log to be void, from
Rami Rosen.
10) Add netns support to the cttimeout infrastructure.
11) Add cgroup2 support to iptables, from Tejun Heo.
12) Introduce nfnl_dereference_protected() in nfnetlink, from Florian.
13) Add support for mangling pkttype in the nf_tables meta expression,
also from Florian.
BTW, I need that you pull net into net-next, I have another batch that
requires changes that I don't yet see in net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 17 Dec 2015 14:18:44 +0000 (14:18 +0000)]
nfp: call netif_carrier_off() during init
Netdevs default to carrier on, we should call netif_carrier_off()
during initialization since we handle carrier state changes in the
driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Dec 2015 19:43:39 +0000 (14:43 -0500)]
Merge branch 'l3mdev-accept'
David Ahern says:
====================
net: Allow accepted sockets to be bound to l3mdev domain
Allow accepted sockets to derive their sk_bound_dev_if setting from the
l3mdev domain in which the packets originated. This version adds a sysctl
to control whether the setting is inherited, making the functionality
similar to sk_mark and its sysctl_tcp_fwmark_accept setting.
This effectively allow a process to have a "VRF-global" listen socket,
with child sockets bound to the VRF device in which the packet originated.
A similar behavior can be achieved using sk_mark, but a solution using marks
is incomplete as it does not handle duplicate addresses in different L3
domains/VRFs. Allowing sockets to inherit the sk_bound_dev_if from l3mdev
domain provides a complete solution.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 16 Dec 2015 21:20:44 +0000 (13:20 -0800)]
net: Allow accepted sockets to be bound to l3mdev domain
Allow accepted sockets to derive their sk_bound_dev_if setting from the
l3mdev domain in which the packets originated. A sysctl setting is added
to control the behavior which is similar to sk_mark and
sysctl_tcp_fwmark_accept.
This effectively allow a process to have a "VRF-global" listen socket,
with child sockets bound to the VRF device in which the packet originated.
A similar behavior can be achieved using sk_mark, but a solution using marks
is incomplete as it does not handle duplicate addresses in different L3
domains/VRFs. Allowing sockets to inherit the sk_bound_dev_if from l3mdev
domain provides a complete solution.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 16 Dec 2015 15:44:38 +0000 (16:44 +0100)]
ipv6: addrconf: use stable address generator for ARPHRD_NONE
Add a new address generator mode, using the stable address generator
with an automatically generated secret. This is intended as a default
address generator mode for device types with no EUI64 implementation.
The new generator is used for ARPHRD_NONE interfaces initially, adding
default IPv6 autoconf support to e.g. tun interfaces.
If the addrgenmode is set to 'random', either by default or manually,
and no stable secret is available, then a random secret is used as
input for the stable-privacy address generator. The secret can be
read and modified like manually configured secrets, using the proc
interface. Modifying the secret will change the addrgen mode to
'stable-privacy' to indicate that it operates on a known secret.
Existing behaviour of the 'stable-privacy' mode is kept unchanged. If
a known secret is available when the device is created, then the mode
will default to 'stable-privacy' as before. The mode can be manually
set to 'random' but it will behave exactly like 'stable-privacy' in
this case. The secret will not change.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: 吉藤英明 <hideaki.yoshifuji@miraclelinux.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 18 Dec 2015 14:37:37 +0000 (15:37 +0100)]
ila: add NETFILTER dependency
The recently added generic ILA translation facility fails to
build when CONFIG_NETFILTER is disabled:
net/ipv6/ila/ila_xlat.c:229:20: warning: 'struct nf_hook_state' declared inside parameter list
net/ipv6/ila/ila_xlat.c:235:27: error: array type has incomplete element type 'struct nf_hook_ops'
static struct nf_hook_ops ila_nf_hook_ops[] __read_mostly = {
This adds an explicit Kconfig dependency to avoid that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 7f00feaf1076 ("ila: Add generic ILA translation facility") Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 10 Dec 2015 17:04:07 +0000 (18:04 +0100)]
netfilter: meta: add support for setting skb->pkttype
This allows to redirect bridged packets to local machine:
ether type ip ether daddr set aa:53:08:12:34:56 meta pkttype set unicast
Without 'set unicast', ip stack discards PACKET_OTHERHOST skbs.
It is also useful to add support for a '-m cluster like' nft rule
(where switch floods packets to several nodes, and each cluster node
node processes a subset of packets for load distribution).
Mangling is restricted to HOST/OTHER/BROAD/MULTICAST, i.e. you cannot set
skb->pkt_type to PACKET_KERNEL or change PACKET_LOOPBACK to PACKET_HOST.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix uninitialized variable warnings in nfnetlink_queue, a lot of
people reported this... From Arnd Bergmann.
2) Don't init mutex twice in i40e driver, from Jesse Brandeburg.
3) Fix spurious EBUSY in rhashtable, from Herbert Xu.
4) Missing DMA unmaps in mvpp2 driver, from Marcin Wojtas.
5) Fix race with work structure access in pppoe driver causing
corruptions, from Guillaume Nault.
6) Fix OOPS due to sh_eth_rx() not checking whether netdev_alloc_skb()
actually succeeded or not, from Sergei Shtylyov.
7) Don't lose flags when settifn IFA_F_OPTIMISTIC in ipv6 code, from
Bjørn Mork.
8) VXLAN_HD_RCO defined incorrectly, fix from Jiri Benc.
9) Fix clock source used for cookies in SCTP, from Marcelo Ricardo
Leitner.
10) aurora driver needs HAS_DMA dependency, from Geert Uytterhoeven.
11) ndo_fill_metadata_dst op of vxlan has to handle ipv6 tunneling
properly as well, from Jiri Benc.
12) Handle request sockets properly in xfrm layer, from Eric Dumazet.
13) Double stats update in ipv6 geneve transmit path, fix from Pravin B
Shelar.
14) sk->sk_policy[] needs RCU protection, and as a result
xfrm_policy_destroy() needs to free policies using an RCU grace
period, from Eric Dumazet.
15) SCTP needs to clone ipv6 tx options in order to avoid use after
free, from Eric Dumazet.
16) Missing kbuild export if ila.h, from Stephen Hemminger.
17) Missing mdiobus_alloc() return value checking in mdio-mux.c, from
Tobias Klauser.
18) Validate protocol value range in ->create() methods, from Hannes
Frederic Sowa.
19) Fix early socket demux races that result in illegal dst reuse, from
Eric Dumazet.
20) Validate socket address length in pptp code, from WANG Cong.
21) skb_reorder_vlan_header() uses incorrect offset and can corrupt
packets, from Vlad Yasevich.
22) Fix memory leaks in nl80211 registry code, from Ola Olsson.
23) Timeout loop count handing fixes in mISDN, xgbe, qlge, sfc, and
qlcnic. From Dan Carpenter.
24) msg.msg_iocb needs to be cleared in recvfrom() otherwise, for
example, AF_ALG will interpret it as an async call. From Tadeusz
Struk.
25) inetpeer_set_addr_v4 forgets to initialize the 'vif' field, from
Eric Dumazet.
26) rhashtable enforces the minimum table size not early enough,
breaking how we calculate the per-cpu lock allocations. From
Herbert Xu.
27) Fix FCC port lockup in 82xx driver, from Martin Roth.
28) FOU sockets need to be freed using RCU, from Hannes Frederic Sowa.
29) Fix out-of-bounds access in __skb_complete_tx_timestamp() and
sock_setsockopt() wrt. timestamp handling. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (117 commits)
net: check both type and procotol for tcp sockets
drivers: net: xgene: fix Tx flow control
tcp: restore fastopen with no data in SYN packet
af_unix: Revert 'lock_interruptible' in stream receive code
fou: clean up socket with kfree_rcu
82xx: FCC: Fixing a bug causing to FCC port lock-up
gianfar: Don't enable RX Filer if not supported
net: fix warnings in 'make htmldocs' by moving macro definition out of field declaration
rhashtable: Fix walker list corruption
rhashtable: Enforce minimum size on initial hash table
inet: tcp: fix inetpeer_set_addr_v4()
ipv6: automatically enable stable privacy mode if stable_secret set
net: fix uninitialized variable issue
bluetooth: Validate socket address length in sco_sock_bind().
net_sched: make qdisc_tree_decrease_qlen() work for non mq
ser_gigaset: remove unnecessary kfree() calls from release method
ser_gigaset: fix deallocation of platform device structure
ser_gigaset: turn nonsense checks into WARN_ON
ser_gigaset: fix up NULL checks
qlcnic: fix a timeout loop
...
Eran Ben Elisha [Thu, 17 Dec 2015 14:11:55 +0000 (16:11 +0200)]
team: Advertise tunneling offload features
When the underlying device supports offloads encapulated traffic,
we need to reflect that through the hw_enc_features field of the
team net-device.
This will cause the xmit path in the core networking stack to provide
team with encapsulated GSO frames to offload into the HW etc.
Using this over Mellanox ConnectX3-pro (mlx4 driver) card that supports
VXLAN offloads we got 36.0 Gbits/sec using eight iperf streams.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Thu, 17 Dec 2015 11:44:04 +0000 (12:44 +0100)]
net: qmi_wwan: ignore bogus CDC Union descriptors
The CDC descriptors found on these vendor specific functions should
not be considered authoritative. They seem to be ignored by drivers
for other systems, and the quality is therefore low.
One device (1e0e:9001) has been reported to have such a bogus union
descriptor on the QMI function, making it fail probing even if the
device id was dynamically added. The report was not complete enough
to allow adding a device entry for this modem. But this should at
least fix the dynamic id probing problem.
Reported-by: Kanerva Topi <Topi.Kanerva@cinia.fi> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 17 Dec 2015 09:51:04 +0000 (10:51 +0100)]
net/macb: Update device tree binding for resetting PHY using GPIO
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 17 Dec 2015 20:51:05 +0000 (15:51 -0500)]
Merge branch 'cxgb4-l2-table-enhancements'
Hariprasad Shenai says:
====================
Few l2 table related enhancements for cxgb4
This series adds a new API to allocate and update l2t entry, replaces
arpq_head/arpq_tail with double skb double linked list. Use t4_mgmt_tx()
to send control packets of l2t write request. Use symbolic constants
while calculating vlan priority.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2: Remove unnecessary MAS operation while calculating vlan prio in
PATCH 1/4 ("cxgb4: Use symbolic constant for VLAN priority calculation")
based on review comment by David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is because we mistake a raw socket as a tcp socket.
We should check both sk->sk_type and sk->sk_protocol to ensure
it is a tcp socket.
Willem points out __skb_complete_tx_timestamp() needs to fix as well.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Tx flow control is based on reading the hardware state,
which is not accurate since it may not reflect the descriptors that
are not yet reached the memory.
To accurately control the Tx flow, changing it to be software based.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Dec 2015 21:53:10 +0000 (13:53 -0800)]
tcp: restore fastopen with no data in SYN packet
Yuchung tracked a regression caused by commit 57be5bdad759 ("ip: convert
tcp_sendmsg() to iov_iter primitives") for TCP Fast Open.
Some Fast Open users do not actually add any data in the SYN packet.
Fixes: 57be5bdad759 ("ip: convert tcp_sendmsg() to iov_iter primitives") Reported-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Wed, 16 Dec 2015 20:09:25 +0000 (20:09 +0000)]
af_unix: Revert 'lock_interruptible' in stream receive code
With b3ca9b02b00704053a38bfe4c31dbbb9c13595d0, the AF_UNIX SOCK_STREAM
receive code was changed from using mutex_lock(&u->readlock) to
mutex_lock_interruptible(&u->readlock) to prevent signals from being
delayed for an indefinite time if a thread sleeping on the mutex
happened to be selected for handling the signal. But this was never a
problem with the stream receive code (as opposed to its datagram
counterpart) as that never went to sleep waiting for new messages with the
mutex held and thus, wouldn't cause secondary readers to block on the
mutex waiting for the sleeping primary reader. As the interruptible
locking makes the code more complicated in exchange for no benefit,
change it back to using mutex_lock.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 16 Dec 2015 19:08:52 +0000 (19:08 +0000)]
nfp: clear ring delayed kick counters
We need to clear delayed kick counters when we free rings otherwise
after ndo_close()/ndo_open() we could kick HW by more entries than
actually written to rings.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 16 Dec 2015 09:50:11 +0000 (17:50 +0800)]
ipv6: allow routes to be configured with expire values
Add the support for adding expire value to routes, requested by
Tom Gundersen <teg@jklm.no> for systemd-networkd, and NetworkManager
wants it too.
implement it by adding the new RTNETLINK attribute RTA_EXPIRES.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 17 Dec 2015 19:55:29 +0000 (11:55 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some i915 fixes, one omap fix, one core regression fix.
Not even enough fixes for a twelve days of xmas song, which seemms
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Don't overwrite UNVERFIED mode status to OK
drm/omap: fix fbdev pix format to support all platforms
drm/i915: Do a better job at disabling primary plane in the noatomic case.
drm/i915/skl: Double RC6 WRL always on
drm/i915/skl: Disable coarse power gating up until F0
drm/i915: Remove incorrect warning in context cleanup
and then publish the current CPU in the lock tail:
old = atomic_xchg_acquire(&lock->tail, curr);
Once the update to lock->tail is visible to another CPU, the node is
then live and can be both read and updated by concurrent lockers.
Unfortunately, the ACQUIRE semantics of the xchg operation mean that
there is no guarantee the contents of the node will be visible before
lock tail is updated. This can lead to lock corruption when, for
example, a concurrent locker races to set the next field.
Fixes: c55a6ffa6285 ("locking/osq: Relax atomic semantics"): Reported-by: David Daney <ddaney@caviumnetworks.com> Reported-by: Andrew Pinski <andrew.pinski@caviumnetworks.com> Tested-by: Andrew Pinski <andrew.pinski@caviumnetworks.com> Acked-by: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: http://lkml.kernel.org/r/1449856001-21177-1-git-send-email-will.deacon@arm.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 17 Dec 2015 19:20:13 +0000 (11:20 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Two bug fixes for misuse of PAGE_MASK in scatterlist and dma-debug.
These are tagged for -stable. The scatterlist impact is potentially
corrupted dma addresses on HIGHMEM enabled platforms.
- A minor locking fix for the NFIT hot-add implementation that is new
in 4.4-rc. This would only trigger in the case a hot-add raced
driver removal.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dma-debug: Fix dma_debug_entry offset calculation
Revert "scatterlist: use sg_phys()"
nfit: acpi_nfit_notify(): Do not leave device locked
fou->udp_offloads is managed by RCU. As it is actually included inside
the fou sockets, we cannot let the memory go out of scope before a grace
period. We either can synchronize_rcu or switch over to kfree_rcu to
manage the sockets. kfree_rcu seems appropriate as it is used by vxlan
and geneve.
Fixes: 23461551c00628c ("fou: Support for foo-over-udp RX path") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Pass ndm_state to route netlink FDB notifications.
Before this change applications monitoring FDB notifications
were not able to determine whether a new FDB entry is permament
or not:
bridge fdb add f1:f2:f3:f4:f5:f8 dev sw0p1 temp self
bridge fdb add f1:f2:f3:f4:f5:f9 dev sw0p1 self
bridge monitor fdb
f1:f2:f3:f4:f5:f8 dev sw0p1 self permanent
f1:f2:f3:f4:f5:f9 dev sw0p1 self permanent
With this change ndm_state from the original netlink message
is passed to the new netlink message sent as notification.
bridge fdb add f1:f2:f3:f4:f5:f6 dev sw0p1 self
bridge fdb add f1:f2:f3:f4:f5:f7 dev sw0p1 temp self
bridge monitor fdb
f1:f2:f3:f4:f5:f6 dev sw0p1 self permanent
f1:f2:f3:f4:f5:f7 dev sw0p1 self static
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Roth [Tue, 15 Dec 2015 02:17:53 +0000 (04:17 +0200)]
82xx: FCC: Fixing a bug causing to FCC port lock-up
The patch fixes FCC port lock-up, which occurs as a result of a bug
during underrun/collision handling. Within the tx_startup() function
in mac-fcc.c, the address of last BD is not calculated correctly.
As a result of wrong calculation of the last BD address, the next
transmitted BD may be set to an area out of the transmit BD ring.
This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hamish Martin [Tue, 15 Dec 2015 01:14:50 +0000 (14:14 +1300)]
gianfar: Don't enable RX Filer if not supported
After commit 15bf176db1fb ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176db1fb ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.
We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mentz [Wed, 16 Dec 2015 01:38:48 +0000 (17:38 -0800)]
dma-debug: Fix dma_debug_entry offset calculation
dma-debug uses struct dma_debug_entry to keep track of dma coherent
memory allocation requests. The virtual address is converted into a pfn
and an offset. Previously, the offset was calculated using an incorrect
bit mask. As a result, we saw incorrect error messages from dma-debug
like the following:
"DMA-API: exceeded 7 overlapping mappings of cacheline 0x03e00000"
Cacheline 0x03e00000 does not exist on our platform.
Cc: <stable@vger.kernel.org> Fixes: 0abdd7a81b7e ("dma-debug: introduce debug_dma_assert_idle()") Signed-off-by: Daniel Mentz <danielmentz@google.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Wed, 16 Dec 2015 18:57:24 +0000 (10:57 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Further ARM fixes:
- Anson Huang noticed that we were corrupting a register we shouldn't
be during suspend on some CPUs.
- Shengjiu Wang spotted a bug in the 'swp' instruction emulation.
- Will Deacon fixed a bug in the ASID allocator.
- Laura Abbott fixed the kernel permission protection to apply to all
threads running in the system.
- I've fixed two bugs with the domain access control register
handling, one to do with printing an appropriate value at oops
time, and the other to further fix the uaccess_with_memcpy code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8475/1: SWP emulation: Restore original *data when failed
ARM: 8471/1: need to save/restore arm register(r11) when it is corrupted
ARM: fix uaccess_with_memcpy() with SW_DOMAIN_PAN
ARM: report proper DACR value in oops dumps
ARM: 8464/1: Update all mm structures with section adjustments
ARM: 8465/1: mm: keep reserved ASIDs in sync with mm after multiple rollovers
net: fix warnings in 'make htmldocs' by moving macro definition out of field declaration
Docbook does not like the definition of macros inside a field declaration
and adds a warning. Move the definition out.
Fixes: 79462ad02e86180 ("net: add validation for the socket syscall protocol argument") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 16 Dec 2015 08:45:54 +0000 (16:45 +0800)]
rhashtable: Fix walker list corruption
The commit ba7c95ea3870fe7b847466d39a049ab6f156aa2c ("rhashtable:
Fix sleeping inside RCU critical section in walk_stop") introduced
a new spinlock for the walker list. However, it did not convert
all existing users of the list over to the new spin lock. Some
continued to use the old mutext for this purpose. This obviously
led to corruption of the list.
The fix is to use the spin lock everywhere where we touch the list.
This also allows us to do rcu_rad_lock before we take the lock in
rhashtable_walk_start. With the old mutex this would've deadlocked
but it's safe with the new spin lock.
Fixes: ba7c95ea3870 ("rhashtable: Fix sleeping inside RCU...") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 16 Dec 2015 16:09:40 +0000 (11:09 -0500)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- change my email in MAINTAINERS and Doc files
- create and export list of single hop neighs per interface
- protect CRC in the BLA code by means of its own lock
- minor fixes and code cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 16 Dec 2015 15:59:05 +0000 (10:59 -0500)]
Merge branch 'geneve-udp-port-offload'
Anjali Singhai Jain says:
====================
Add support for Geneve udp port offload
This patch series adds new ndo ops for Geneve add/del port, so as
to help offload Geneve tunnel functionalities such as RX checksum,
RSS, filters etc.
i40e driver has been tested with the changes to make sure the offloads
happen.
We do understand that this is not the ideal solution and most likely
will be redone with a more generic offload framework.
But this certainly will enable us to start seeing benefits of the
accelerations for Geneve tunnels.
As a side note, we did find an existing issue in i40e driver where a
service task can modify tunnel data structures with no locks held to
help linearize access. A separate patch will be taking care of that issue.
A question out to the community is regarding the driver Kconfig parameters
for VxLAN and Geneve, it would be ideal to drop those if there is a way
to help resolve vxlan/geneve_get_rx_port symbols while the tunnel modules
are not loaded.
Performance numbers:
With the offloads enable on X722 devices with remote checksum enabled
and no other tuning in terms of cpu governer etc on my test machine:
With offload
Throughput: 5527Mbits/sec with a single thread
%cpu: ~43% per core with 4 threads
Without offload
Throughput: 2364Mbits/sec with a single thread
%cpu: ~99% per core with 4 threads
These numbers will get better for X722 as it is being worked. But
this does bring out the delta in terms of when the stack is notified
with csum_level 1 and CHECKSUM_UNNECESSARY vs not without the RX offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Singhai, Anjali [Mon, 14 Dec 2015 20:21:19 +0000 (12:21 -0800)]
i40e: Kernel dependency update for i40e to support geneve offload
Update the Kconfig file with dependency for supporting GENEVE tunnel
offloads.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Singhai, Anjali [Mon, 14 Dec 2015 20:21:18 +0000 (12:21 -0800)]
i40e: geneve tunnel offload support
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Singhai, Anjali [Mon, 14 Dec 2015 20:21:17 +0000 (12:21 -0800)]
geneve: Add geneve udp port offload for ethernet devices
Add ndo_ops to add/del UDP ports to a device that supports geneve
offload.
v2: Comment fix.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Wed, 16 Dec 2015 05:55:04 +0000 (13:55 +0800)]
net: sctp: dynamically enable or disable pf state
As we all know, the value of pf_retrans >= max_retrans_path can
disable pf state. The variables of pf_retrans and max_retrans_path
can be changed by the userspace application.
Sometimes the user expects to disable pf state while the 2
variables are changed to enable pf state. So it is necessary to
introduce a new variable to disable pf state.
According to the suggestions from Vlad Yasevich, extra1 and extra2
are removed. The initialization of pf_enable is added.
Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 16 Dec 2015 10:13:14 +0000 (18:13 +0800)]
rhashtable: Enforce minimum size on initial hash table
William Hua <william.hua@canonical.com> wrote:
>
> I wasn't aware there was an enforced minimum size. I simply set the
> nelem_hint in the rhastable_params struct to 1, expecting it to grow as
> needed. This caused a segfault afterwards when trying to insert an
> element.
OK we're doing the size computation before we enforce the limit
on min_size.
---8<---
We need to do the initial hash table size computation after we
have obtained the correct min_size/max_size parameters. Otherwise
we may end up with a hash table whose size is outside the allowed
envelope.
Fixes: a998f712f77e ("rhashtable: Round up/down min/max_size to...") Reported-by: William Hua <william.hua@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich [Fri, 11 Sep 2015 16:04:13 +0000 (18:04 +0200)]
batman-adv: lock crc access in bridge loop avoidance
We have found some networks in which nodes were constantly requesting
other nodes BLA claim tables to synchronize, just to ask for that again
once completed. The reason was that the crc checksum of the asked nodes
were out of sync due to missing locking and multiple writes to the same
crc checksum when adding/removing entries. Therefore the asked nodes
constantly reported the wrong crc, which caused repeating requests.
To avoid multiple functions changing a backbone gateways crc entry at
the same time, lock it using a spinlock.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Tested-by: Alfons Name <AlfonsName@web.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Sven Eckelmann [Wed, 26 Aug 2015 08:31:51 +0000 (10:31 +0200)]
batman-adv: Fix typo 'wether' -> 'whether'
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Sven Eckelmann [Wed, 26 Aug 2015 08:31:50 +0000 (10:31 +0200)]
batman-adv: Use chain pointer when purging fragments
The chain pointer was already created in batadv_frag_purge_orig to make the
checks more readable. Just use the chain pointer everywhere instead of
having the same dereference + array access in the most lines of this
function.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Simon Wunderlich [Wed, 26 Aug 2015 14:33:34 +0000 (16:33 +0200)]
batman-adv: unify flags access style in tt global add
This should slightly improve readability
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
batman-adv: detect local excess vlans in TT request
If the local representation of the global TT table of one originator has
more VLAN entries than the respective TT update, there is some
inconsistency present. By detecting and reporting this inconsistency,
the global table gets updated and the excess VLAN will get removed in
the process.
Reported-by: Alessandro Bolletta <alessandro@mediaspot.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Acked-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
projects / linux-beck.git / log