Glauber Costa [Tue, 11 May 2010 16:17:40 +0000 (12:17 -0400)]
x86, paravirt: Add a global synchronization point for pvclock
In recent stress tests, it was found that pvclock-based systems
could seriously warp in smp systems. Using ingo's time-warp-test.c,
I could trigger a scenario as bad as 1.5mi warps a minute in some systems.
(to be fair, it wasn't that bad in most of them). Investigating further, I
found out that such warps were caused by the very offset-based calculation
pvclock is based on.
This happens even on some machines that report constant_tsc in its tsc flags,
specially on multi-socket ones.
Two reads of the same kernel timestamp at approx the same time, will likely
have tsc timestamped in different occasions too. This means the delta we
calculate is unpredictable at best, and can probably be smaller in a cpu
that is legitimately reading clock in a forward ocasion.
Some adjustments on the host could make this window less likely to happen,
but still, it pretty much poses as an intrinsic problem of the mechanism.
A while ago, I though about using a shared variable anyway, to hold clock
last state, but gave up due to the high contention locking was likely
to introduce, possibly rendering the thing useless on big machines. I argue,
however, that locking is not necessary.
We do a read-and-return sequence in pvclock, and between read and return,
the global value can have changed. However, it can only have changed
by means of an addition of a positive value. So if we detected that our
clock timestamp is less than the current global, we know that we need to
return a higher one, even though it is not exactly the one we compared to.
OTOH, if we detect we're greater than the current time source, we atomically
replace the value with our new readings. This do causes contention on big
boxes (but big here means *BIG*), but it seems like a good trade off, since
it provide us with a time source guaranteed to be stable wrt time warps.
After this patch is applied, I don't see a single warp in time during 5 days
of execution, in any of the machines I saw them before.
Signed-off-by: Glauber Costa <glommer@redhat.com> Acked-by: Zachary Amsden <zamsden@redhat.com> CC: Jeremy Fitzhardinge <jeremy@goop.org> CC: Avi Kivity <avi@redhat.com> CC: Marcelo Tosatti <mtosatti@redhat.com> CC: Zachary Amsden <zamsden@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 489fb490dbf8dab0249ad82b56688ae3842a79e8)
KVM: SVM: Report emulated SVM features to userspace
This patch implements the reporting of the emulated SVM
features to userspace instead of the real hardware
capabilities. Every real hardware capability needs emulation
in nested svm so the old behavior was broken.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit c2c63a493924e09a1984d1374a0e60dfd54fc0b0)
KVM: x86: Add callback to let modules decide over some supported cpuid bits
This patch adds the get_supported_cpuid callback to
kvm_x86_ops. It will be used in do_cpuid_ent to delegate the
decission about some supported cpuid bits to the
architecture modules.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit d4330ef2fb2236a1e3a176f0f68360f4c0a8661b)
Joerg Roedel [Fri, 19 Feb 2010 15:23:01 +0000 (16:23 +0100)]
KVM: SVM: Fix wrong interrupt injection in enable_irq_windows
The nested_svm_intr() function does not execute the vmexit
anymore. Therefore we may still be in the nested state after
that function ran. This patch changes the nested_svm_intr()
function to return wether the irq window could be enabled.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 8fe546547cf6857a9d984bfe2f2194910f3fc5d0)
Joerg Roedel [Fri, 19 Feb 2010 15:23:06 +0000 (16:23 +0100)]
KVM: SVM: Don't sync nested cr8 to lapic and back
This patch makes syncing of the guest tpr to the lapic
conditional on !nested. Otherwise a nested guest using the
TPR could freeze the guest.
Another important change this patch introduces is that the
cr8 intercept bits are no longer ORed at vmrun emulation if
the guest sets VINTR_MASKING in its VMCB. The reason is that
nested cr8 accesses need alway be handled by the nested
hypervisor because they change the shadow version of the
tpr.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 88ab24adc7142506c8583ac36a34fa388300b750)
Joerg Roedel [Fri, 19 Feb 2010 15:23:05 +0000 (16:23 +0100)]
KVM: SVM: Fix nested msr intercept handling
The nested_svm_exit_handled_msr() function maps only one
page of the guests msr permission bitmap. This patch changes
the code to use kvm_read_guest to fix the bug.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 4c7da8cb43c09e71a405b5aeaa58a1dbac3c39e9)
Joerg Roedel [Fri, 19 Feb 2010 15:23:03 +0000 (16:23 +0100)]
KVM: SVM: Sync all control registers on nested vmexit
Currently the vmexit emulation does not sync control
registers were the access is typically intercepted by the
nested hypervisor. But we can not count on that intercepts
to sync these registers too and make the code
architecturally more correct.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit cdbbdc1210223879450555fee04c29ebf116576b)
Joerg Roedel [Fri, 19 Feb 2010 15:23:00 +0000 (16:23 +0100)]
KVM: SVM: Don't use kmap_atomic in nested_svm_map
Use of kmap_atomic disables preemption but if we run in
shadow-shadow mode the vmrun emulation executes kvm_set_cr3
which might sleep or fault. So use kmap instead for
nested_svm_map.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 7597f129d8b6799da7a264e6d6f7401668d3a36d)
J.R. Okajima reports that the call to sync_inode() in nfs_wb_page() can
deadlock with other writeback flush calls. It boils down to the fact
that we cannot ever call writeback_single_inode() while holding a page
lock (even if we do set nr_to_write to zero) since another process may
already be waiting in the call to do_writepages(), and so will deny us
the I_SYNC lock.
If we exit from nfs_commit_inode() without ensuring that the COMMIT rpc
call has been completed, we must re-mark the inode as dirty. Otherwise,
future calls to sync_inode() with the WB_SYNC_ALL flag set will fail to
ensure that the data is on the disk.
On btrfs, do the following
------------------
# su user1
# cd btrfs-part/
# touch aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rw-
group::rw-
other::r--
# su user2
# cd btrfs-part/
# setfacl -m u::rwx aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rwx <- successed to setfacl
group::rw-
other::r--
------------------
but we should prohibit it that user2 changing user1's acl.
In fact, on ext3 and other fs, a message occurs:
setfacl: aaa: Operation not permitted
This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While creating a file on a server which supports unix extensions
such as Samba, if a file is being created which does not supply
nameidata (i.e. nd is null), cifs client can oops when calling
cifs_posix_open.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Roseberg has reported a problem with the MOVE_EXT ioctl. If the
donor file is an append-only file, we should not allow the operation
to proceed, lest we end up overwriting the contents of an append-only
file.
If groups_per_flex < 2, sbi->s_flex_groups[] doesn't get filled out,
and every other access to this first tests s_log_groups_per_flex;
same thing needs to happen in resize or we'll wander off into
a null pointer when doing an online resize of the file system.
Thanks to Christoph Biedl, who came up with the trivial testcase:
In order to move toward separate buffer objects, rework the whole
perf_mmap_data construct to be a more self-sufficient entity, one
with its own lifetime rules.
This greatly sanitizes the whole output redirection code, which
was riddled with bugs and races.
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Tested-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
But without this conversion we can't guarantee that a SETATTR request
has actually been commited to disk with XFS, which causes a regression
from 2.6.32 (only for NFSv2, but anyway).
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Frederic reported that frequency driven swevents didn't work properly
and even caused a division-by-zero error.
It turns out there are two bugs, the division-by-zero comes from a
failure to deal with that in perf_calculate_period().
The other was more interesting and turned out to be a wrong comparison
in perf_adjust_period(). The comparison was between an s64 and u64 and
got implicitly converted to an unsigned comparison. The problem is
that period_left is typically < 0, so it ended up being always true.
Cure this by making the local period variables s64.
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I got below oops when unloading cfq-iosched. Considering scenario:
queue A merge to B, C merge to D and B will be merged to D. Before B is merged
to D, we do split B. We should put B's reference for D.
Add Dell WLA3310 USB wireless card, which has a Z-Com XG-705A chipset, to the
USB Ids in p54usb.
Signed-off-by: Jason Dravet <dravet@hotmail.com> Tested-by: Richard Gregory Tillmore <rtillmore@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1387) fixes a bug introduced during the changeover to
the runtime PM framework. When a driver doesn't support resume or
reset-resume, and consequently its interfaces need to be unbound and
rebound, we have to unbind all the interfaces before trying to rebind
any of them. Otherwise the driver's probe method for one interface
could try to claim a different interface and fail, because that other
interface hasn't been unbound yet.
This fixes Bugzilla #15788. The symptom is that some USB sound cards
don't work after hibernation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: François Valenduc <francois.valenduc@tvcablenet.be> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Johan Hovold <jhovold@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
We can, by virtue of a vblank interrupt firing in the middle of setting
up the unpin work (i.e. after we set the unpin_work field and before we
write to the ringbuffer) enter intel_finish_page_flip() prior to
receiving the pending flip notification. Therefore we can expect to hit
intel_finish_page_flip() under normal circumstances without a pending flip
and even without installing the pending_flip_obj. This is exacerbated by
aperture thrashing whilst binding the framebuffer
References:
Bug 28079 - "glresize" causes kernel panic in intel_finish_page_flip.
https://bugs.freedesktop.org/show_bug.cgi?id=28079
Reported-by: Nick Bowler <nbowler@draconx.ca> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw> Reported-by: Jorrit Tijben <sjorrit@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
If reserve_pmc_hardware() succeeds but reserve_ds_buffers()
fails, then we need to release_pmc_hardware. It won't be done
by the destroy() callback because we return before setting it
in case of error.
Child groups should have a greater depth than their parents. Prior to
this change, the parent would incorrectly report zero memory usage for
child cgroups when use_hierarchy is enabled.
test script:
mount -t cgroup none /cgroups -o memory
cd /cgroups
mkdir cg1
Using fae9c79, a recent patch that changed alloc_css_id() depth computation,
the parent incorrectly reports zero usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0151844 s, 69.1 MB/s
With this patch, the parent correctly includes child usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0136827 s, 76.6 MB/s
10, 233 is allocated officially to /dev/kmview which is shipping in
Ubuntu and Debian distributions. vhost_net seem to have borrowed it
without making a proper request and this causes regressions in the other
distributions.
vhost_net can use a dynamic minor so use that instead. Also update the
file with a comment to try and avoid future misunderstandings.
Signed-off-by: Alan Cox <device@lanana.org>
[ We should have caught this before 2.6.34 got released. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Per IEEE 1394 clause 8.4.2.3, a contender for the IRM role shall check
whether the current IRM complies to 1394a-2000 or later. If not force a
compliant node (e.g. itself) to become IRM. This was implemented in the
older ieee1394 driver but not yet in firewire-core.
An older Sony camcorder (Sony DCR-TRV25) which implements 1394-1995 IRM
but neither 1394a-2000 IRM nor BM was now found to cause an
interoperability bug:
- Camcorder becomes root node when plugged in, hence gets IRM role.
- firewire-core successfully contends for BM role, proceeds to perform
gap count optimization and resets the bus.
- Sony camcorder ignores presence of a BM (against the spec, this is
a firmware bug), performs its idea of gap count optimization and
resets the bus.
- Preceding two steps are repeated endlessly, bus never settles,
regular I/O is practically impossible.
http://thread.gmane.org/gmane.linux.kernel.firewire.user/3913
This is an interoperability regression from the old to the new drivers.
Fix it indirectly by adding the 1394a IRM check. The spec suggests
three and a half methods to determine 1394a compliance of a remote IRM;
we choose the method of testing the Config_ROM.Bus_Info.generation
field. This is data that firewire-core should have readily available at
this point, i.e. does not require extra I/O.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (missing 1394a check) Reported-by: H. S. <hs.samix@gmail.com> (issue with Sony DCR-TRV25) Tested-by: H. S. <hs.samix@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Aries Lee <arieslee@jmicron.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 56d1de0a21db28e41741cfa0a66e18bc8d920554, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com Tested-by: weedy2887@gmail.com Tested-by: Rick Farina <sidhayn@gmail.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a8408c17 introduced a new check to pccard_validate_cis(),
which avoids any "late" calls to this function. This broke the
insertion of cards which require a CIS override which changes
the number of card functions. Fix this by asserting that this
is _not_ a late call, but a proper call early during the card
insertion process.
Keeping the saved I365_CSCINT flag around breaks PCMCIA on some system,
and is only needed on a few systems to get PCMCIA to work. This patch
allows PCMCIA to work on both types, and it fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16015
Making gconfig fails on fedora 13 as the linker cannot resolve dlsym.
Adding libdl to the link command fixes this.
make shows this error :-
/usr/bin/ld: scripts/kconfig/kconfig_load.o: undefined reference to symbol 'dlsym@@GLIBC_2.2.5'
/usr/bin/ld: note: 'dlsym@@GLIBC_2.2.5' is defined in DSO /lib64/libdl.so.2 so try adding it to the linker command line
/lib64/libdl.so.2: could not read symbols: Invalid operation
tested on x86_64 fedora 13.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on the sh_tmu change in 66f49121ffa41a19c59965b31b046d8368fec3c7
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 98962465ed9e6ea99c38e0af63fe1dcb5a79dc25 ("nohz: Prevent
clocksource wrapping during idle"), the CPU of an R2D board never goes
to idle. This commit assumes that mult and shift are assigned before
the clocksource is registered. As a consequence the safe maximum sleep
time is negative and the CPU never goes into idle.
This patch fixes the problem by moving mult and shift initialization
from sh_tmu_clocksource_enable() to sh_tmu_register_clocksource().
Correct at least one of the incorrect specs for a national instrument
data acquisition card DAQCard-6024E. This card has only four different
gain settings (+-10V, +-5V, +-0.5V, +-0.05V).
Signed-off-by: Martin Homuth-Rosemann <homuth-rosemann@gmx.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Limit number of accumulated non-balloonable pages during inflation cycle,
otherwise there is a chance we will be spinning and growing the list
forever. This happens during torture tests when balloon target changes
while we are in the middle of inflation cycle and monitor starts refusing
to lock pages (since they are not needed anymore).
BugLink: https://launchpad.net/bugs/587546
Symptom: On the reporter's ASUS M2V, using PulseAudio in Ubuntu 10.04 LTS
results in the PA daemon crashing shortly after attempting playback of an
audio file.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, attempt playback of an audio file while PulseAudio is
active.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: D Tangman Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/580749
Symptom: on the original reporter's VIA VT1708-based board, the
PulseAudio daemon dies shortly after the user attempts to play an audio
file.
Test case: boot from Ubuntu 10.04 LTS live cd; attempt to play an audio
file.
Resolution: add SSID for the original reporter's hardware to the
position_fix quirk table, explicitly specifying the LPIB method.
Reported-and-Tested-By: Harald Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/542550
Symptom: On the reporter's iMac, in Ubuntu 10.04 LTS neither playback
nor capture appear audible out-of-the-box.
Test case: Boot from an Ubuntu 10.04 LTS live cd or from an installed
configuration and attempt to play or capture audio.
Resolution: Specify the mb31 quirk for this machine in the codec SSID
table.
Reported-and-Tested-By: f3a97 Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/465942
Symptom: On the reporter's ASUS device, using PulseAudio in Ubuntu 10.04
LTS results in the PA daemon crashing shortly after attempting to select
capture or to configure the audio hardware profile.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's capture volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Irihapeti Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the device we are resuming could be the device containing the
swap device we should ensure that the allocation cannot cause
IO.
On resume, this path is triggered when the running system tries to
continue using its devices. If it cannot then the resume will fail;
to try to avoid this we let it dip into the emergency pools.
The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.
As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.
xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.
Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The low-memory corruption checker triggers during suspend/resume, so we
need to reserve the low 64k. Don't be fooled that the BIOS identifies
itself as "Dell Inc.", it's still Phoenix BIOS.
[ hpa: I think we blacklist almost every BIOS in existence. We should
either change this to a whitelist or just make it unconditional. ]
Signed-off-by: Gabor Gombas <gombasg@digikabel.hu>
LKML-Reference: <201005241913.o4OJDIMM010877@imap1.linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I/O errors can happen due to temporary failures, like multipath
errors or losing network contact with the iSCSI server. Because
of that, the VM will retry readpage on the page.
However, do_generic_file_read does not clear PG_error. This
causes the system to be unable to actually use the data in the
page cache page, even if the subsequent readpage completes
successfully!
The function filemap_fault has had a ClearPageError before
readpage forever. This patch simply adds the same to
do_generic_file_read.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Larry Woodman <lwoodman@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A call to access_ok is missing a compat_ptr conversion. Introduced with b83733639a494d5f42fa00a2506563fbd2d3015d "compat: factor out
compat_rw_copy_check_uvector from compat_do_readv_writev"
fs/compat.c: In function 'compat_rw_copy_check_uvector':
fs/compat.c:629: warning: passing argument 1 of '__access_ok' makes pointer from integer without a cast
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was reported in http://lkml.org/lkml/2010/3/8/309 that 32 bit readv and
writev AIO operations were not functioning properly. It turns out that
the code to convert the 32bit io vectors to 64 bits was never written.
The results of that can be pretty bad, but in my testing, it mostly ended
up in generating EFAULT as we walked off the list of I/O vectors provided.
This patch set fixes the problem in my environment. are greatly
appreciated.
This patch:
Factor out code that will be used by both compat_do_readv_writev and the
compat aio submission code paths.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Reported-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Tridgell reports that aio_read(SIGEV_SIGNAL) can fail if the
notification from the helper thread races with setresuid(), see
http://samba.org/~tridge/junkcode/aio_uid.c
This happens because check_kill_permission() doesn't permit sending a
signal to the task with the different cred->xids. But there is not any
security reason to check ->cred's when the task sends a signal (private or
group-wide) to its sub-thread. Whatever we do, any thread can bypass all
security checks and send SIGKILL to all threads, or it can block a signal
SIG and do kill(gettid(), SIG) to deliver this signal to another
sub-thread. Not to mention that CLONE_THREAD implies CLONE_VM.
Change check_kill_permission() to avoid the credentials check when the
sender and the target are from the same thread group.
Also, move "cred = current_cred()" down to avoid calling get_current()
twice.
Note: David Howells pointed out we could relax this even more, the
CLONE_SIGHAND (without CLONE_THREAD) case probably does not need
these checks too.
Roland said:
: The glibc (libpthread) that does set*id across threads has
: been in use for a while (2.3.4?), probably in distro's using kernels as old
: or older than any active -stable streams. In the race in question, this
: kernel bug is breaking valid POSIX application expectations.
Reported-by: Andrew Tridgell <tridge@samba.org> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Cc: Eric Paris <eparis@parisplace.org> Cc: Jakub Jelinek <jakub@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Roland McGrath <roland@redhat.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is meant to improve the performance of SLUB by moving the local
kmem_cache_node lock into it's own cacheline separate from kmem_cache.
This is accomplished by simply removing the local_node when NUMA is enabled.
On my system with 2 nodes I saw around a 5% performance increase w/
hackbench times dropping from 6.2 seconds to 5.9 seconds on average. I
suspect the performance gain would increase as the number of nodes
increases, but I do not have the data to currently back that up.
Bugzilla-Reference: http://bugzilla.kernel.org/show_bug.cgi?id=15713 Reported-by: Alex Shi <alex.shi@intel.com> Tested-by: Alex Shi <alex.shi@intel.com> Acked-by: Yanmin Zhang <yanmin_zhang@linux.intel.com> Acked-by: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 756dee75872a2a764b478e18076360b8a4ec9045 ("SLUB: Get rid of dynamic DMA
kmalloc cache allocation") makes S390 run out of kmalloc caches. Increase the
number of kmalloc caches to a safe size.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the i.MX SSI driver to make it compatible with the ASoC tree
following the move of DMA parameters from the DAI to the audio substream
object.
Signed-off-by: Stuart Longland <redhatter@gentoo.org> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently idr_remove_all will fail with a use after free error if
idr::layers is bigger than 2, which on 32 bit systems corresponds to items
more than 1024. This is due to stepping back too many levels during
backtracking. For simplicity let's assume that IDR_BITS=1 -> we have 2
nodes at each level below the root node and each leaf node stores two IDs.
(In reality for 32 bit systems IDR_BITS=5, with 32 nodes at each sub-root
level and 32 IDs in each leaf node). The sequence of freeing the nodes at
the moment is as follows:
Until step 4 things go fine, but then node c is freed, whereas node g
should be freed first. Since node c contains the pointer to node g we'll
have a use after free error at step 6.
How many levels we step back after visiting the leaf nodes is currently
determined by the msb of the id we are currently visiting:
Step
1. node d with IDs 0,1 is freed, current ID is advanced to 2.
msb of the current ID bit 1. This means we need to step back
1 level to node b and take the next sibling, node e.
2-3. node e with IDs 2,3 is freed, current ID is 4, msb is bit 2.
This means we need to step back 2 levels to node a, freeing
node b on the way.
4-5. node f with IDs 4,5 is freed, current ID is 6, msb is still
bit 2. This means we again need to step back 2 levels to node
a and free c on the way.
6. We should visit node g, but its pointer is not available as
node c was freed.
The fix changes how we determine the number of levels to step back.
Instead of deducting this merely from the msb of the current ID, we should
really check if advancing the ID causes an overflow to a bit position
corresponding to a given layer. In the above example overflow from bit 0
to bit 1 should mean stepping back 1 level. Overflow from bit 1 to bit 2
should mean stepping back 2 levels and so on.
The fix was tested with IDs up to 1 << 20, which corresponds to 4 layers
on 32 bit systems.
Signed-off-by: Imre Deak <imre.deak@nokia.com> Reviewed-by: Tejun Heo <tj@kernel.org> Cc: Eric Paris <eparis@redhat.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The aio compat code was not converting the struct iovecs from 32bit to
64bit pointers, causing either EINVAL to be returned from io_getevents, or
EFAULT as the result of the I/O. This patch passes a compat flag to
io_submit to signal that pointer conversion is necessary for a given iocb
array.
A variant of this was tested by Michael Tokarev. I have also updated the
libaio test harness to exercise this code path with good success.
Further, I grabbed a copy of ltp and ran the
testcases/kernel/syscall/readv and writev tests there (compiled with -m32
on my 64bit system). All seems happy, but extra eyes on this would be
welcome.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix CONFIG_COMPAT=n build] Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Reported-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vfp_put_double() takes the double value in r0,r1 not r1,r2.
Reported-by: Tarun Kanti DebBarma <tarun.kanti@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bug in mm/init.c when freeing the TCM compile memory,
this was being referred to as a char * which is incorrect: this
will dereference the pointer and feed in the value at the location
instead of the address to it. Change it to a plain char and use
&(char) to reference it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reorganises the sa1111_resume() function in a manner the spinlock
happens after calling the sa1111_wake(). This fixes two bugs:
1) This function called sa1111_wake() which tried to claim the same spinlock
the sa1111_resume() already claimed. This would result in certain deadlock.
Original idea for this part: Russell King <rmk+kernel@arm.linux.org.uk>
2) The function didn't unlock the spinlock in case the chip didn't report
correct ID.
Original idea for this part: Julia Lawall <julia@diku.dk>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When functions incoming parameters are not in input operands list gcc
4.5 does not load the parameters into registers before calling this
function but the inline assembly assumes valid addresses inside this
function. This breaks the code because r0 and r1 are invalid when
execution enters v4wb_copy_user_page ()
Also the constant needs to be used as third input operand so account
for that as well.
Tested on qemu arm.
Signed-off-by: Khem Raj <raj.khem@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instruction faults on pre-ARMv6 CPUs are interpreted as
a 'translation fault', but do_translation_fault doesn't
handle well if user mode trying to run instruction above
TASK_SIZE, and result in the infinite retry of that
instruction.
Signed-off-by: Anfei Zhou <anfei.zhou@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the number of sg entries in the ICM chunk reaches MLX4_ICM_CHUNK_LEN,
we must set chunk to NULL even for coherent mappings so that the next
time through the loop will allocate another chunk. Otherwise we'll
overflow the sg list the next time through the loop. This will lead to
memory corruption if this case is hit.
Some levels expect the 'redundancy group' to be present,
others don't.
So when we change level of an array we might need to
add or remove this group.
This requires fixing up the current practice of overloading ->private
to indicate (when ->pers == NULL) that something needs to be removed.
So create a new ->to_remove to fill that role.
When changing levels, we may need to add or remove attributes. When
changing RAID5 -> RAID6, we both add and remove the same thing. It is
important to catch this and optimise it out as the removal is delayed
until a lock is released, so trying to add immediately would cause
problems.
Shaohua Li reported parallel file copy on tmpfs can lead to OOM killer.
This is regression of caused by commit 9ff473b9a7 ("vmscan: evict
streaming IO first"). Wow, It is 2 years old patch!
Currently, tmpfs file cache is inserted active list at first. This means
that the insertion doesn't only increase numbers of pages in anon LRU, but
it also reduces anon scanning ratio. Therefore, vmscan will get totally
confused. It scans almost only file LRU even though the system has plenty
unused tmpfs pages.
Historically, lru_cache_add_active_anon() was used for two reasons.
1) Intend to priotize shmem page rather than regular file cache.
2) Intend to avoid reclaim priority inversion of used once pages.
But we've lost both motivation because (1) Now we have separate anon and
file LRU list. then, to insert active list doesn't help such priotize.
(2) In past, one pte access bit will cause page activation. then to
insert inactive list with pte access bit mean higher priority than to
insert active list. Its priority inversion may lead to uninteded lru
chun. but it was already solved by commit 645747462 (vmscan: detect
mapped file pages used only once). (Thanks Hannes, you are great!)
Thus, now we can use lru_cache_add_anon() instead.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Reported-by: Shaohua Li <shaohua.li@intel.com> Reviewed-by: Wu Fengguang <fengguang.wu@intel.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe:
the buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Chris Zankel <chris@zankel.net> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bug is an oops when dev_get_drvdata() returned null in
cmos_update_irq_enable(). The call tree looks like this:
rtc_dev_ioctl()
=> rtc_update_irq_enable()
=> cmos_update_irq_enable()
It's caused by a race condition in the module initialization. It is
rtc_device_register() which makes the ioctl operations live so I moved
the call to dev_set_drvdata() before the call to rtc_device_register().
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 8b505ca8e2600eb9e7dd2d6b2682a81717671374 ("serial: 68328serial.c:
remove BAUD_TABLE_SIZE macro") misses one use of BAUD_TABLE_SIZE. So the
resulting 68328serial.c does not compile:
drivers/serial/68328serial.c: In function `m68328_console_setup':
drivers/serial/68328serial.c:1439: error: `BAUD_TABLE_SIZE' undeclared (first use in this function)
drivers/serial/68328serial.c:1439: error: (Each undeclared identifier is reported only once
drivers/serial/68328serial.c:1439: error: for each function it appears in.)
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: David Howells <dhowells@redhat.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We set the "it's dead, don't mount on it" flag _and_ do not remove it if
we turn the damn thing negative and leave it around. And if it goes
positive afterwards, well...
Fortunately, there's only one place where that needs to be caught:
only d_delete() can turn the sucker negative without immediately freeing
it; all other places that can lead to ->d_iput() call are followed by
unconditionally freeing struct dentry in question. So the fix is obvious:
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16014 Reported-by: Adam Tkac <vonsch@gmail.com> Tested-by: Adam Tkac <vonsch@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eeepc-wmi uses backlight*() interfaces so it should depend on
BACKLIGHT_CLASS_DEVICE.
eeepc-wmi.c:(.text+0x2d7f54): undefined reference to `backlight_force_update'
eeepc-wmi.c:(.text+0x2d8012): undefined reference to `backlight_device_register'
eeepc-wmi.c:(.devinit.text+0x1c31c): undefined reference to `backlight_device_unregister'
eeepc-wmi.c:(.devexit.text+0x2f8b): undefined reference to `backlight_device_unregister'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a fallback to the GART IOMMU if this
is possible and the AMD IOMMU initialization failed.
Otherwise the fallback would be nommu which is very
problematic on machines with more than 4GB of memory or
swiotlb which hurts io-performance.
projects / karo-tx-linux.git / log