Right new have one irq chip running always in level mode. It would nicer
to have two irq chips where one is handling level type interrupts and
the other one is doing edge interrupts. So we can have at runtime two users
where one is using edge and the other level.
Acked-by: Alan Tull <delicious.quinoa@gmail.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Michael Stickel [Mon, 26 May 2014 08:03:16 +0000 (10:03 +0200)]
gpio: mcp23s08: fixed count variable for devicetree probing
Fixed missing increase of count variable for devicetree path in driver
probing.
The gpio-mcp23s08 driver has two paths for getting the platform
registration information. One for the classic platform initialization
and one for openfirmware devicetree based initialization. The devicetree
based path is missing the increase of the count variable, which results
in the count variable to become negative in the later use, where it is
decreased. The count variable is used as an index into a vector. This
results in accessing invalid memory space and can result in an exception.
Tested this with an AM3352 SoC with two mcp23s17 on two chip selects as
well as on a shared chip select.
Signed-off-by: Michael Stickel <ms@mycable.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 27 May 2014 13:15:21 +0000 (15:15 +0200)]
gpio: pch: add slab include
After change 3ff35cbcfa4bc7d7dbdd0279e32ea677567ded02
"gpio-pch: Fix Kconfig dependencies"
which enabled COMPILE_TEST as an alternative for the PCH
driver, we get build failures like this:
drivers/gpio/gpio-pch.c: In function 'pch_gpio_probe':
drivers/gpio/gpio-pch.c:359:2: error: implicit declaration
of function 'kzalloc' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-pch.c:359:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
drivers/gpio/gpio-pch.c:442:2: error: implicit declaration
of function 'kfree' [-Werror=implicit-function-declaration]
Fix this by including <linux/slab.h> explicitly.
Cc: Jean Delvare <jdelvare@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mukesh Rathor [Sat, 24 May 2014 02:33:44 +0000 (19:33 -0700)]
x86/xen: map foreign pfns for autotranslated guests
When running as a dom0 in PVH mode, foreign pfns that are accessed
must be added to our p2m which is managed by xen. This is done via
XENMEM_add_to_physmap_range hypercall. This is needed for toolstack
building guests and mapping guest memory, xentrace mapping xen pages,
etc.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Chris Wilson [Fri, 23 May 2014 06:48:08 +0000 (08:48 +0200)]
drm/i915: Prevent negative relocation deltas from wrapping
This is pure evil. Userspace, I'm looking at you SNA, repacks batch
buffers on the fly after generation as they are being passed to the
kernel for execution. These batches also contain self-referenced
relocations as a single buffer encompasses the state commands, kernels,
vertices and sampler. During generation the buffers are placed at known
offsets within the full batch, and then the relocation deltas (as passed
to the kernel) are tweaked as the batch is repacked into a smaller buffer.
This means that userspace is passing negative relocations deltas, which
subsequently wrap to large values if the batch is at a low address. The
GPU hangs when it then tries to use the large value as a base for its
address offsets, rather than wrapping back to the real value (as one
would hope). As the GPU uses positive offsets from the base, we can
treat the relocation address as the minimum address read by the GPU.
For the upper bound, we trust that userspace will not read beyond the
end of the buffer.
So, how do we fix negative relocations from wrapping? We can either
check that every relocation looks valid when we write it, and then
position each object such that we prevent the offset wraparound, or we
just special-case the self-referential behaviour of SNA and force all
batches to be above 256k. Daniel prefers the latter approach.
This fixes a GPU hang when it tries to use an address (relocation +
offset) greater than the GTT size. The issue would occur quite easily
with full-ppgtt as each fd gets its own VM space, so low offsets would
often be handed out. However, with the rearrangement of the low GTT due
to capturing the BIOS framebuffer, it is already affecting kernels 3.15
onwards. I think only IVB+ is susceptible to this bug, but the workaround
should only kick in rarely, so it seems sensible to always apply it.
v3: Use a bias for batch buffers to prevent small negative delta relocations
from wrapping.
v4 from Daniel:
- s/BIAS/BATCH_OFFSET_BIAS/
- Extract eb_vma_misplaced/i915_vma_misplaced since the conditions
were growing rather cumbersome.
- Add a comment to eb_get_batch explaining why we do this.
- Apply the batch offset bias everywhere but mention that we've only
observed it on gen7 gpus.
- Drop PIN_OFFSET_FIX for now, that slipped in from a feature patch.
v5: Add static to eb_get_batch, spotted by 0-day tester.
Testcase: igt/gem_bad_reloc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78533 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3) Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 23 May 2014 09:45:52 +0000 (10:45 +0100)]
drm/i915: Only copy back the modified fields to userspace from execbuffer
We only want to modifiy a single field in the userspace view of the
execbuffer command buffer, so explicitly change that rather than copy
everything back again.
This serves two purposes:
1. The single fields are much cheaper to copy (constant size so the
copy uses special case code) and much smaller than the whole array.
2. We modify the array for internal use that need to be masked from
the user.
Note: We need this backported since without it the next bugfix will
blow up when userspace recycles batchbuffers and relocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 21 May 2014 11:42:56 +0000 (12:42 +0100)]
drm/i915: Fix dynamic allocation of physical handles
A single object may be referenced by multiple registers fundamentally
breaking the static allotment of ids in the current design. When the
object is used the second time, the physical address of the first
assignment is relinquished and a second one granted. However, the
hardware is still reading (and possibly writing) to the old physical
address now returned to the system. Eventually hilarity will ensue, but
in the short term, it just means that cursors are broken when using more
than one pipe.
v2: Fix up leak of pci handle when handling an error during attachment,
and avoid a double kmap/kunmap. (Ville)
Rebase against -fixes.
v3: And fix the error handling added in v2 (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77351 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hans de Goede [Tue, 20 May 2014 05:54:09 +0000 (22:54 -0700)]
Input: synaptics - change min/max quirk table to pnp-id matching
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hans de Goede [Tue, 20 May 2014 05:52:30 +0000 (22:52 -0700)]
Input: synaptics - T540p - unify with other LEN0034 models
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Code subject to #ifdef CONSOLE is made more generic, as was apparently
intended by the original author.
Remove console_put_stats() routine. If it should be somehow useful, it
should also be useful on platforms without framebuffer debug logging. The
present implementation is only built #if defined CONFIG_MAC && defined
CONSOLE even though puts() works everywhere.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stephen N Chivers <schivers@csc.com.au> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Michael Schmitz [Mon, 31 Mar 2014 08:06:06 +0000 (21:06 +1300)]
m68k/atari - atafb: convert allocation of fb ram to new interface
The new atari_stram_alloc interface returns kernel virtual addresses
even if the kernel runs in FastRAM. These addresses are not
guaranteed to be identical with the physical addresses. Since ST-RAM
mappings have not been set up by mem_init, virt_to_phys() and its
cousin do not work and the atari_stram_to_phys() etc. helpers must
be used to determine physical addresses.
fb.fix->smem_start needs physical addresses, fb.par->screen_base
needs virtual addresses. Take care of the virt-to-phys conversion
both on fb init and par changes.
Signed-off-by: Michael Schmitz <schmitz@debian.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Michael Schmitz [Mon, 31 Mar 2014 08:06:05 +0000 (21:06 +1300)]
m68k/atari - stram: alloc ST-RAM pool even if kernel not in ST-RAM
With the kernel loaded to FastRAM (TT-RAM), none of the ST-RAM
address range is mapped by init_mem, and ST-RAM is not accessible
through the normal allocation pathways as a result.
Implement ST-RAM pool allocation to be based on physical addresses
always (it already was when the kernel was loaded in ST-RAM).
Return kernel virtual addresses as per normal.
The current test for the kernel residing in ST-RAM always returns
true. Use the bootinfo memory chunk order instead - with the kernel
in FastRAM, ST-RAM (phys. 0x0) is not the first chunk.
In case the kernel is running from FastRAM, delay mapping of ST-RAM
pool until after mem_init.
Provide helper functions for those users of ST-RAM that need
to be aware of the backing physical addresses.
Kudos to Geert for his hints on getting this started.
Signed-off-by: Michael Schmitz <schmitz@debian.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Aaron Lu [Mon, 26 May 2014 12:34:07 +0000 (14:34 +0200)]
ACPI / thermal: fix workqueue destroy order
When the thermal module is to be removed, we should destroy the wq
acpi_thermal_pm_queue after the ACPI driver's remove callback is
executed as we will need to flush the workqueue there, or a NULL pointer
access will be hit.
Reported-and-tested-by: Kui Zhang <kuizhang@gmail.com>
References: http://www.spinics.net/lists/kernel/msg1747251.html Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The parent field of the 'rc32434_res_pci_mem1' resource points to
the resource itself which is obviously wrong. Due to the broken
initialitazion, the PCI devices on the Mikrotik RB532 boards are
not working since commit 22283178 (MIPS: avoid possible resource
conflict in register_pci_controller).
Rabin Vincent [Sat, 24 May 2014 16:38:01 +0000 (17:38 +0100)]
ARM: 8064/1: fix v7-M signal return
According to the ARM ARM, the behaviour is UNPREDICTABLE if the PC read
from the exception return stack is not half word aligned. See the
pseudo code for ExceptionReturn() and PopStack().
The signal handler's address has the bit 0 set, and setup_return()
directly writes this to regs->ARM_pc. Current hardware happens to
discard this bit, but QEMU's emulation doesn't and this makes processes
crash. Mask out bit 0 before the exception return in order to get
predictable behaviour.
Fixes: 19c4d593f0b4 ("ARM: ARMv7-M: Add support for exception handling") Cc: stable@kernel.org Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
srinik [Thu, 15 May 2014 10:28:44 +0000 (11:28 +0100)]
ARM: 8057/1: amba: Add Qualcomm vendor ID.
This patch adds Qualcomm amba vendor Id to the list. This ID is used in mmci driver. The ID selected in same lines like 0x41 is "A" for ARM, 0x51 is "Q" for Qualcomm.
As there are no physical register on Qcom SOC for amba vendor id, this is a fake ID assigned based on "Q" prefix from Qualcomm.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nikolay Borisov [Thu, 8 May 2014 14:54:26 +0000 (15:54 +0100)]
ARM: 8052/1: unwind: Fix handling of "Pop r4-r[4+nnn],r14" opcode
The arm EABI states that unwind opcode 10100nnn means pop register r4-4[4+nnn],aditionally there is a similar unwind opcode: 10101nnn which means the same thing plus popping r14. Those two cases are handled by the unwind_exec_pop_r4_to_rN function which checks whether the 4th bit is set and does r14 popping.
However, up until now it has been checking whether the 8th bit was set (mask & 0x80) instead of the 4th (mask & 0x8), a simple to make typo but this meant that we were always popping r14 even if we had the former opcode.
This patch changes the mask so that the 2 unwind opcodes are being handled correctly.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com> Reviewed-by: Anurag Aggarwal <anurag19aggarwal@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrey Ryabinin [Wed, 7 May 2014 07:07:25 +0000 (08:07 +0100)]
ARM: 8051/1: put_user: fix possible data corruption in put_user
According to arm procedure call standart r2 register is call-cloberred.
So after the result of x expression was put into r2 any following
function call in p may overwrite r2. To fix this, the result of p
expression must be saved to the temporary variable before the
assigment x expression to __r2.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Sat, 3 May 2014 17:19:17 +0000 (18:19 +0100)]
ARM: 8048/1: fix v7-M setup stack location
__v7m_setup_stack currently sits in the .proc.info.init section, and
thus creates a bogus proc info entry (which by the way matches any
unknown CPU IDs, due to the entry's mask being 0). Move it out of
there.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sun, 25 May 2014 19:40:36 +0000 (12:40 -0700)]
Merge branch 'afs' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes and cleanups from David Howells:
"Here are some patches to the AFS filesystem:
1) Fix problems in the clean-up parts of the cache manager service
handler.
2) Split afs_end_call() introduced in (1) and replace some identical
code elsewhere with a call to the first half of the split function.
3) Fix an error introduced in the workqueue PREPARE_WORK() elimination
commits.
4) Clean up argument passing to functions called from the workqueue as
there's now an insulating layer between them and the workqueue.
This is possible from (3)"
* 'afs' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
AFS: Pass an afs_call* to call->async_workfn() instead of a work_struct*
AFS: Fix kafs module unloading
AFS: Part of afs_end_call() is identical to code elsewhere, so split it
AFS: Fix cache manager service handlers
The sum at the beginning of line "intr" includes also unnumbered
interrupts. It implies that the sum at the beginning isn't the sum
of the remainder of the line, not even an estimation.
Fixed the documentation to mention that.
This behaviour was added to /proc/stat in commit a2eddfa95919 ("x86:
make /proc/stat account for all interrupts")
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 May 2014 17:13:50 +0000 (10:13 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull single scsi fix from James Bottomley:
"This is a single fix for a bug exposed by a sysfs change in 3.13 which
now causes libsas to trigger a warn on in device removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] scsi_transport_sas: move bsg destructor into sas_rphy_remove
Linus Torvalds [Sun, 25 May 2014 17:08:48 +0000 (10:08 -0700)]
Merge branch 'for-3.15' of git://linux-nfs.org/~bfields/linux
Pull two nfsd bugfixes from Bruce Fields:
"Just two bugfixes, one for a merge-window-introduced ACL regression,
the other for a longer-standing v4 state bug"
* 'for-3.15' of git://linux-nfs.org/~bfields/linux:
nfsd4: warn on finding lockowner without stateid's
nfsd4: remove lockowner when removing lock stateid
nfsd4: fix corruption on setting an ACL.
Jean Delvare [Sun, 25 May 2014 15:23:08 +0000 (17:23 +0200)]
hwmon: (ntc_thermistor) Fix OF device ID mapping
The mapping from OF device IDs to platform device IDs is wrong.
TYPE_NCPXXWB473 is 0, TYPE_NCPXXWL333 is 1, so
ntc_thermistor_id[TYPE_NCPXXWB473] is { "ncp15wb473", TYPE_NCPXXWB473 }
while
ntc_thermistor_id[TYPE_NCPXXWL333] is { "ncp18wb473", TYPE_NCPXXWB473 }.
So the name is wrong for all but the "ntc,ncp15wb473" entry, and the
type is wrong for the "ntc,ncp15wl333" entry.
So map the entries by index, it is neither elegant nor robust but at
least it is correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver Reviewed-by: Guenter Roeck <linux@roeck-us.net> Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Cc: Doug Anderson <dianders@chromium.org>
Jean Delvare [Sun, 25 May 2014 15:23:08 +0000 (17:23 +0200)]
hwmon: (ntc_thermistor) Fix dependencies
In commit 9e8269de, support was added for ntc_thermistor devices being
declared in the device tree and implemented on top of IIO. With that
change, a dependency was added to the ntc_thermistor driver:
depends on (!OF && !IIO) || (OF && IIO)
This construct has the drawback that the driver can no longer be
selected when OF is set and IIO isn't, nor when IIO is set and OF is
not. This is a regression for the original users of the driver.
As the new code depends on IIO and is useless without OF, include it
only if both are enabled, and set the dependencies accordingly. This
is clearer, more simple and more correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver Reviewed-by: Guenter Roeck <linux@roeck-us.net> Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Cc: Doug Anderson <dianders@chromium.org>
Markos Chandras [Fri, 23 May 2014 12:31:31 +0000 (13:31 +0100)]
MIPS: malta: memory.c: Initialize the 'memsize' variable
If the 'memsize' environmental variable is not set by the bootloader
the 'memsize' variable is not initialized, leading to potential memory
problems. This patch fixes the problem by setting the initial
value to '0' to force the kernel to set a good default memory size.
Huacai Chen [Sun, 25 May 2014 02:00:36 +0000 (10:00 +0800)]
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
Originally, __NR_O32_Linux_syscalls, __NR_N32_Linux_syscalls and
__NR_64_Linux_syscalls have the same values as __NR_Linux_syscalls in
corresponding ABIs. But after commit 367f0b50e502d (MIPS: Wire up
renameat2 syscall) they are not the same. I think this is incorrect and
need a fix.
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6987/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Fri, 23 May 2014 23:52:15 +0000 (16:52 -0700)]
Merge tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
"Two fixes for -stable:
- async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
- mv_xor: register write ordering fix"
* tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: fix dmaengine_unmap failure
dma: mv_xor: Flush descriptors before activating a channel
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
Arnd Bergmann [Fri, 23 May 2014 21:59:28 +0000 (23:59 +0200)]
Merge tag 'samsung-fixes-2nd-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Samsung-fixes-2 for 3.15
- keep LD04 always on for exynos5250-arndale
- fix spi interrupt numbers for exynos5420
- fix ak8975 compatible for exynos4412-trats2
* tag 'samsung-fixes-2nd-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Keep LDO4 always ON for exynos5250-arndale board
ARM: dts: Fix SPI interrupt numbers for exynos5420
ARM: dts: fix incorrect ak8975 compatible for exynos4412-trats2 board
Maxime COQUELIN [Wed, 7 May 2014 16:48:52 +0000 (18:48 +0200)]
clk: divider: Fix table round up function
Commit 1d9fe6b97 ("clk: divider: Fix best div calculation for power-of-two and
table dividers") introduces a regression in its _table_round_up function.
When the divider passed to this function is greater than the max divider
available in the table, this function returns table's max divider.
Problem is that it causes an infinite loop in clk_divider_bestdiv() because
_next_div() will never return a value greater than maxdiv.
Instead of returning table's max divider, this patch returns INT_MAX.
Jens Axboe [Fri, 23 May 2014 20:14:57 +0000 (14:14 -0600)]
blk-mq: allow setting of per-request timeouts
Currently blk-mq uses the queue timeout for all requests. But
for some commands, drivers may want to set a specific timeout
for special requests. Allow this to be passed in through
request->timeout, and use it if set.
Sam Bradshaw [Fri, 23 May 2014 19:30:16 +0000 (13:30 -0600)]
blk-mq: export blk_mq_tag_busy_iter
Export the blk-mq in-flight tag iterator for driver consumption.
This is particularly useful in exception paths or SRSI where
in-flight IOs need to be cancelled and/or reissued. The NVMe driver
conversion will use this.
ARM: trusted_foundations: fix compile error on non-SMP
The setup_max_cpus variable is only defined if CONFIG_SMP is set. Add
a preprocessor condition to avoid the following compilation error if
CONFIG_SMP is not set:
arch/arm/include/asm/trusted_foundations.h: In function 'register_trusted_foundations':
arch/arm/include/asm/trusted_foundations.h:57:2: error: 'setup_max_cpus' undeclared (first use in this function)
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Fri, 23 May 2014 17:04:04 +0000 (10:04 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"The biggest commit is an irqtime accounting loop latency fix, the rest
are misc fixes all over the place: deadline scheduling, docs, numa,
balancer and a bad to-idle latency fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Initialize newidle balance stats in sd_numa_init()
sched: Fix updating rq->max_idle_balance_cost and rq->next_balance in idle_balance()
sched: Skip double execution of pick_next_task_fair()
sched: Use CPUPRI_NR_PRIORITIES instead of MAX_RT_PRIO in cpupri check
sched/deadline: Fix memory leak
sched/deadline: Fix sched_yield() behavior
sched: Sanitize irq accounting madness
sched/docbook: Fix 'make htmldocs' warnings caused by missing description
Linus Torvalds [Fri, 23 May 2014 17:02:34 +0000 (10:02 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest changes are fixes for races that kept triggering Trinity
crashes, plus liblockdep build fixes and smaller misc fixes.
The liblockdep bits in perf/urgent are a pull mistake - they should
have been in locking/urgent - but by the time I noticed other commits
were added and testing was done :-/ Sorry about that"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race between ring_buffer_detach() and ring_buffer_attach()
perf: Prevent false warning in perf_swevent_add
perf: Limit perf_event_attr::sample_period to 63 bits
tools/liblockdep: Remove all build files when doing make clean
tools/liblockdep: Build liblockdep from tools/Makefile
perf/x86/intel: Fix Silvermont's event constraints
perf: Fix perf_event_init_context()
perf: Fix race in removing an event
Linus Torvalds [Fri, 23 May 2014 16:41:33 +0000 (09:41 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm radeon and nouveau fixes from Dave Airlie:
"Fixes for the other big two.
The radeon VCE one is large but it fixes some userspace triggerable
issues, otherwise its blackscreens and oopses.
Nouveau fixes a bleeding laptop panel issue when displayport is used
sometimes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/pm: don't allow debugfs/sysfs access when PX card is off (v2)
drm/radeon: avoid segfault on device open when accel is not working.
drm/radeon: fix typo in finding PLL params
drm/radeon: fix register typo on si
drm/radeon: fix buffer placement under memory pressure v2
drm/radeon: fix page directory update size estimation
drm/radeon: handle non-VGA class pci devices with ATRM
drm/radeon: fix DCE83 check for mullins
drm/radeon: check VCE relocation buffer range v3
drm/radeon: also try GART for CPU accessed buffers
drm/gf119-/disp: fix nasty bug which can clobber SOR0's clock setup
drm/nvd9/therm: handle another kind of PWM fan
Linus Torvalds [Fri, 23 May 2014 16:38:07 +0000 (09:38 -0700)]
Merge branch 'akpm' (incoming from Andrew)
Merge misc fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add closing angle bracket to Vince Bridgers' email address
Documentation: fix DOCBOOKS=... building
ocfs2: fix double kmem_cache_destroy in dlm_init
mm/memory-failure.c: fix memory leak by race between poison and unpoison
wait: swap EXIT_ZOMBIE(Z) and EXIT_DEAD(X) chars in TASK_STATE_TO_CHAR_STR
memcg: fix swapcache charge from kernel thread context
mm: madvise: fix MADV_WILLNEED on shmem swapouts
mm/filemap.c: avoid always dirtying mapping->flags on O_DIRECT
hwpoison, hugetlb: lock_page/unlock_page does not match for handling a free hugepage
Johannes Berg [Thu, 22 May 2014 18:54:23 +0000 (11:54 -0700)]
Documentation: fix DOCBOOKS=... building
Prior to commit 4266129964b8 ("[media] DocBook: Move all media docbook
stuff into its own directory") it was possible to build only a single
(or more) book(s) by calling, for example
make htmldocs DOCBOOKS=80211.xml
This now fails:
cp: target `.../Documentation/DocBook//media_api' is not a directory
Ignore errors from that copy to make this possible again.
Fixes: 4266129964b8 ("[media] DocBook: Move all media docbook stuff into its own directory") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Thu, 22 May 2014 18:54:22 +0000 (11:54 -0700)]
ocfs2: fix double kmem_cache_destroy in dlm_init
In dlm_init, if create dlm_lockname_cache failed in
dlm_init_master_caches, it will destroy dlm_lockres_cache which created
before twice. And this will cause system die when loading modules.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 22 May 2014 18:54:21 +0000 (11:54 -0700)]
mm/memory-failure.c: fix memory leak by race between poison and unpoison
When a memory error happens on an in-use page or (free and in-use)
hugepage, the victim page is isolated with its refcount set to one.
When you try to unpoison it later, unpoison_memory() calls put_page()
for it twice in order to bring the page back to free page pool (buddy or
free hugepage list). However, if another memory error occurs on the
page which we are unpoisoning, memory_failure() returns without
releasing the refcount which was incremented in the same call at first,
which results in memory leak and unconsistent num_poisoned_pages
statistics. This patch fixes it.
Masatake YAMATO [Thu, 22 May 2014 18:54:20 +0000 (11:54 -0700)]
wait: swap EXIT_ZOMBIE(Z) and EXIT_DEAD(X) chars in TASK_STATE_TO_CHAR_STR
In commit ad86622b478e ("wait: swap EXIT_ZOMBIE and EXIT_DEAD to hide
EXIT_TRACE from user-space") the order of task state definitions were
changed: EXIT_DEAD and EXIT_ZOMBIE were swapped. Though the charterers
for the states in TASK_STATE_TO_CHAR_STR string were not updated. This
patch synchronizes the string to the order of definitions.
Michal Hocko [Thu, 22 May 2014 18:54:19 +0000 (11:54 -0700)]
memcg: fix swapcache charge from kernel thread context
Commit 284f39afeaa4 ("mm: memcg: push !mm handling out to page cache
charge function") explicitly checks for page cache charges without any
mm context (from kernel thread context[1]).
This seemed to be the only possible case where memory could be charged
without mm context so commit 03583f1a631c ("memcg: remove unnecessary
!mm check from try_get_mem_cgroup_from_mm()") removed the mm check from
get_mem_cgroup_from_mm(). This however caused another NULL ptr
dereference during early boot when loopback kernel thread splices to
tmpfs as reported by Stephan Kulow:
This patch fixes the issue by reintroducing mm check into
get_mem_cgroup_from_mm. We could do the same trick in
__mem_cgroup_try_charge_swapin as we do for the regular page cache path
but it is not worth troubles. The check is not that expensive and it is
better to have get_mem_cgroup_from_mm more robust.
Johannes Weiner [Thu, 22 May 2014 18:54:17 +0000 (11:54 -0700)]
mm: madvise: fix MADV_WILLNEED on shmem swapouts
MADV_WILLNEED currently does not read swapped out shmem pages back in.
Commit 0cd6144aadd2 ("mm + fs: prepare for non-page entries in page
cache radix trees") made find_get_page() filter exceptional radix tree
entries but failed to convert all find_get_page() callers that WANT
exceptional entries over to find_get_entry(). One of them is shmem swap
readahead in madvise, which now skips over any swap-out records.
Convert it to find_get_entry().
Fixes: 0cd6144aadd2 ("mm + fs: prepare for non-page entries in page cache radix trees") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Thu, 22 May 2014 18:54:16 +0000 (11:54 -0700)]
mm/filemap.c: avoid always dirtying mapping->flags on O_DIRECT
In some testing I ran today (some fio jobs that spread over two nodes),
we end up spending 40% of the time in filemap_check_errors(). That
smells fishy. Looking further, this is basically what happens:
blkdev_aio_read()
generic_file_aio_read()
filemap_write_and_wait_range()
if (!mapping->nr_pages)
filemap_check_errors()
and filemap_check_errors() always attempts two test_and_clear_bit() on
the mapping flags, thus dirtying it for every single invocation. The
patch below tests each of these bits before clearing them, avoiding this
issue. In my test case (4-socket box), performance went from 1.7M IOPS
to 4.0M IOPS.
Signed-off-by: Jens Axboe <axboe@fb.com> Acked-by: Jeff Moyer <jmoyer@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Yucong [Thu, 22 May 2014 18:54:15 +0000 (11:54 -0700)]
hwpoison, hugetlb: lock_page/unlock_page does not match for handling a free hugepage
For handling a free hugepage in memory failure, the race will happen if
another thread hwpoisoned this hugepage concurrently. So we need to
check PageHWPoison instead of !PageHWPoison.
If hwpoison_filter(p) returns true or a race happens, then we need to
unlock_page(hpage).
xen/pciback: Document when the 'unbind' and 'bind' functions are called.
And also mention that you cannot do any pci_reset_function,
pci_reset_slot, or such calls. This is because they take the same
lock as SysFS does - and we would end up with a dead-lock if
we call those functions.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
When the toolstack wants us to drop or add an PCI device it
changes the XenBus state to Configuring - and as result of that
we find out which devices we should still be exporting out and
which ones not. For the ones we don't need anymore we need to
do an PCI reset so that it is ready for the next guest.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
We were doing the operations of freeing and reset in the wrong
order. Granted nothing broke because the reset functions just
set bar->which = 0.
But nonethless this was incorrect.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
We are using 'psdev->dev','found_psdev->dev', and 'dev' at the
same time - and they all point to the same structure.
To keep it straight lets just use one - 'dev'.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Linus Torvalds [Fri, 23 May 2014 16:23:51 +0000 (09:23 -0700)]
parisc: 'renameat2()' doesn't need (or have) a separate compat system call
The 'renameat2()' system call was incorrectly added as a ENTRY_COMP() in
the parisc system call table by commit 18e480aa07f78 ("parisc: add
renameat2 syscall"). That causes a link-time error due to there not
being any compat version of that system call:
arch/parisc/kernel/built-in.o: In function `sys_call_table':
(.rodata+0xad0): undefined reference to `compat_sys_renameat2'
make: *** [vmlinux] Error 1
Easily fixed by marking the system call as being the same for compat as
for native by using ENTRY_SAME() instead of ENTRY_COMP().
* tag 'mvebu-fixes-3.15-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
ARM: mvebu: mvebu-soc-id: keep clock enabled if PCIe unit is enabled
ARM: mvebu: mvebu-soc-id: add missing clk_put() call
Jarkko Nikula [Wed, 21 May 2014 13:58:25 +0000 (16:58 +0300)]
Documentation / ACPI: Fix location of GPIO documentation
Commit fd8e198cfcaa ("Documentation: gpiolib: document new interface")
moved Documentation/gpio.txt to Documentation/gpio/gpio-legacy.txt and added
new documents for descriptor-based interface so fix the the location here to
point Documentation/gpio/ since that what commit ccb6fbb99020
("Documentation / ACPI: update to GPIO descriptor API") was looking for.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Aaron Lu [Tue, 20 May 2014 09:07:38 +0000 (17:07 +0800)]
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
The GPIO operation region handler should be called where sleep is
allowed, so we should use the *_cansleep version of gpiod_get/set APIs
or we will get a warning message complaining invalid context if the GPIO
chip has the cansleep flag set.
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Anthony Fee [Mon, 19 May 2014 17:49:14 +0000 (18:49 +0100)]
gpio: generic: add request function pointer
gpiolib will require all gpio drivers to expicitly set the request
function pointer in the future. To encourage gpio driver developers
to adhere to this standard gpio-generic.c now sets this function
pointer.
David Howells [Wed, 21 May 2014 14:55:26 +0000 (15:55 +0100)]
AFS: Pass an afs_call* to call->async_workfn() instead of a work_struct*
call->async_workfn() can take an afs_call* arg rather than a work_struct* as
the functions assigned there are now called from afs_async_workfn() which has
to call container_of() anyway.
At present, it is not possible to successfully unload the kafs module if there
are outstanding async outgoing calls (those made with afs_make_call()). This
appears to be due to the changes introduced by:
which didn't go far enough. The problem is due to:
(1) The aforementioned commit introduced a separate handler function pointer
in the call, call->async_workfn, in addition to the original workqueue
item, call->async_work, for asynchronous operations because workqueues
subsystem cannot handle the workqueue item pointer being changed whilst
the item is queued or being processed.
(2) afs_async_workfn() was introduced in that commit to be the callback for
call->async_work. Its sole purpose is to run whatever call->async_workfn
points to.
(3) call->async_workfn is only used from afs_async_workfn(), which is only
set on async_work by afs_collect_incoming_call() - ie. for incoming
calls.
(4) call->async_workfn is *not* set by afs_make_call() when outgoing calls are
made, and call->async_work is set afs_process_async_call() - and not
afs_async_workfn().
(5) afs_process_async_call() now changes call->async_workfn rather than
call->async_work to point to afs_delete_async_call() to clean up, but this
is only effective for incoming calls because call->async_work does not
point to afs_async_workfn() for outgoing calls.
(6) Because, for incoming calls, call->async_work remains pointing to
afs_process_async_call() this results in an infinite loop.
Instead, make the workqueue uniformly vector through call->async_workfn, via
afs_async_workfn() and simply initialise call->async_workfn to point to
afs_process_async_call() in afs_make_call().
AFS: Part of afs_end_call() is identical to code elsewhere, so split it
Split afs_end_call() into two pieces, one of which is identical to code in
afs_process_async_call(). Replace the latter with a call to the first part of
afs_end_call().
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu> Signed-off-by: David Howells <dhowells@redhat.com>
Jean Delvare [Fri, 16 May 2014 09:59:14 +0000 (11:59 +0200)]
gpio-pch: Fix Kconfig dependencies
The gpio-pch driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Takashi Iwai [Fri, 23 May 2014 07:02:44 +0000 (09:02 +0200)]
ALSA: hda - Fix onboard audio on Intel H97/Z97 chipsets
The recent Intel H97/Z97 chipsets need the similar setups like other
Intel chipsets for snooping, etc. Especially without snooping, the
audio playback stutters or gets corrupted. This fix patch just adds
the corresponding PCI ID entry with the proper flags.
Reported-and-tested-by: Arthur Borsboom <arthurborsboom@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ralf Baechle [Thu, 22 May 2014 21:19:00 +0000 (23:19 +0200)]
MIPS: Fix branch emulation of branch likely instructions.
Two issues:
o For beql_op, beql_op, bne_op, bnel_op, blez_op, blezl_op, bgtz_op and
bgtzl_op the wrong field was being checked for the instruction opcode.
o For blez_op / blezl_op and bgtz_op / bgtzl_op the test was testing
for the wrong opcode.
Joe Lawrence [Thu, 22 May 2014 21:30:54 +0000 (17:30 -0400)]
[SCSI] scsi_transport_sas: move bsg destructor into sas_rphy_remove
The recent change in sysfs, bcdde7e221a8750f9b62b6d0bd31b72ea4ad9309
"sysfs: make __sysfs_remove_dir() recursive" revealed an asymmetric
rphy device creation/deletion sequence in scsi_transport_sas:
modprobe mpt2sas
sas_rphy_add
device_add A rphy->dev
device_add B sas_device transport class
device_add C sas_end_device transport class
device_add D bsg class
rmmod mpt2sas
sas_rphy_delete
sas_rphy_remove
device_del B
device_del C
device_del A
sysfs_remove_group recursive sysfs dir removal
sas_rphy_free
device_del D warning
where device A is the parent of B, C, and D.
When sas_rphy_free tries to unregister the bsg request queue (device D
above), the ensuing sysfs cleanup discovers that its sysfs group has
already been removed and emits a warning, "sysfs group... not found for
kobject 'end_device-X:0'".
Since bsg creation is a side effect of sas_rphy_add, move its
complementary removal call into sas_rphy_remove. This imposes the
following tear-down order for the devices above: D, B, C, A.
Note the sas_device and sas_end_device transport class devices (B and C
above) are created and destroyed both via the list match traversal in
attribute_container_device_trigger, so the order in which they are
handled is fixed. This is fine as long as they are deleted before their
parent device.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Cong Wang [Thu, 22 May 2014 18:57:17 +0000 (11:57 -0700)]
batman: fix a bogus warning from batadv_is_on_batman_iface()
batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com> Tested-by: Jet Chen <jet.chen@intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Antonio Quartulli <antonio@open-mesh.com> Cc: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 22 May 2014 08:36:55 +0000 (16:36 +0800)]
ipv4: initialise the itag variable in __mkroute_input
the value of itag is a random value from stack, and may not be initiated by
fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID
is not set
This will make the cached dst uncertainty
Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Wed, 21 May 2014 17:19:48 +0000 (13:19 -0400)]
bonding: Send ALB learning packets using the right source
ALB learning packets are currentlyalways sent using the slave mac
address for all vlans configured on top of bond. This is not always
correct, as vlans may change their mac address.
This patch introduced a concept of strict matching where the
source of learning packets can either strictly match the address
passed in, or it can determine a more correct address to use.
There are 3 casese to consider:
1) Switchover. In this case, we have a new active slave and we need
tell the switch about all addresses available on the slave.
2) Monitor. We'll periodically refresh learning info for all slaves.
In this case, we refresh all addresses for current active, and just
the slave address for other slaves.
3) Teaching of disabled adddress. This happens as part of the
failover and in this case, we alwyas to use just the address
provided.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Wed, 21 May 2014 15:24:39 +0000 (11:24 -0400)]
bonding: Don't assume 802.1Q when sending alb learning packets.
TLB/ALB learning packets always assume 802.1Q vlan protocol, but
that is no longer the case since we now have support for Q-in-Q
on top of bonding. Pass the vlan protocol to alb_send_lp_vid()
so that the packets are properly tagged.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 May 2014 19:41:20 +0000 (15:41 -0400)]
Merge tag 'linux-can-fixes-for-3.15-20140521' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-05-21
this is a pull request for net/master, for the v3.15 release cycle, with a
single patch. Christopher R. Baker found a use after free during unloading of
the peak_pci driver. This is fixes in a patch by Stephane Grosjean.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 20 May 2014 11:52:13 +0000 (13:52 +0200)]
net: doc: Update references to skb->rxhash
In commit 61b905da33 ("net: Rename skb->rxhash to skb->hash"), skb->rxhash
was renamed to skb->hash. Update references in Documentation
accordingly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Tue, 20 May 2014 09:38:18 +0000 (11:38 +0200)]
stmmac: Remove unbalanced clk_disable call
The stmmac_open call was calling clk_disable_unprepare on phy init
failure, but it never calls clk_prepare_enable, this causes
a WARN_ON in the clk framework to trigger if for some reason phy init
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhiwu Song [Wed, 7 May 2014 06:46:44 +0000 (14:46 +0800)]
clocksource: marco: Fix the affinity set for local timer of CPU1
irqchip will reject the affinity set to CPUs which is not online
yet. but in the CPU1 wakeup stage, OS only sets CPU1 to be online
after local timer is set, so that causes the irq_set_affinity not
work. this patch moves to irq_force_affinity() for the low level
boot stage.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Jens Axboe [Thu, 22 May 2014 16:40:51 +0000 (10:40 -0600)]
blk-mq: split make request handler for multi and single queue
We want slightly different behavior from them:
- On single queue devices, we currently use the per-process plug
for deferred IO and for merging.
- On multi queue devices, we don't use the per-process plug, but
we want to go straight to hardware for SYNC IO.
Split blk_mq_make_request() into a blk_sq_make_request() for single
queue devices, and retain blk_mq_make_request() for multi queue
devices. Then we don't need multiple checks for q->nr_hw_queues
in the request mapping.
Use the hexadecimal values for the triggers to match what is done for the device
tree. This also fixes compilation issues as the defines have been moved
elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Thomas Petazzoni [Tue, 20 May 2014 14:43:28 +0000 (16:43 +0200)]
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
Due a copy/paste error, the 'reg' values for the third PCIe interface
on Armada 380, and the third and fourth PCIe interfaces on Armada 385
are wrong: they are equal to the one of the second PCIe interface.
This patch fixes this by using the appropriate 'reg' values for those
PCIe interfaces.
Without this fix, the third and fourth PCIe interfaces are unusable on
those platforms.
projects / karo-tx-linux.git / log