Herbert Xu [Tue, 17 Nov 2009 13:18:18 +0000 (05:18 -0800)]
gro: Fix illegal merging of trailer trash
When we've merged skb's with page frags, and subsequently receive
a trailer skb (< MSS) that is not completely non-linear (this can
occur on Intel NICs if the packet size falls below the threshold),
GRO ends up producing an illegal GSO skb with a frag_list.
This is harmless unless the skb is then forwarded through an
interface that requires software GSO, whereupon the GSO code
will BUG.
This patch detects this case in GRO and avoids merging the
trailer skb.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Mon, 16 Nov 2009 22:47:33 +0000 (22:47 +0000)]
net: fix mdio section mismatch warning
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben McKeegan [Mon, 16 Nov 2009 03:44:25 +0000 (03:44 +0000)]
ppp: fix BUG on non-linear SKB (multilink receive)
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Tue, 10 Nov 2009 08:37:47 +0000 (08:37 +0000)]
ixgbe: Fixing EEH handler to handle more than one error
After commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 15 Nov 2009 23:30:24 +0000 (23:30 +0000)]
net: Fix the rollback test in dev_change_name()
net: Fix the rollback test in dev_change_name()
In dev_change_name() an err variable is used for storing the original
call_netdevice_notifiers() errno (negative) and testing for a rollback
error later, but the test for non-zero is wrong, because the err might
have positive value as well - from dev_alloc_name(). It means the
rollback for a netdevice with a number > 0 will never happen. (The err
test is reordered btw. to make it more readable.)
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sriram [Thu, 12 Nov 2009 01:55:42 +0000 (01:55 +0000)]
TI Davinci EMAC : Fix Console Hang when bringing the interface down
In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com> Acked-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sriram [Thu, 12 Nov 2009 02:14:38 +0000 (02:14 +0000)]
smsc911x: Fix Console Hang when bringing the interface down.
In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Basic Mode is the default mode of operation of a L2CAP entity. In
this case the RFC (Retransmission and Flow Control) configuration
option should not be used at all.
Normally remote L2CAP implementation should just ignore this option,
but it can cause various side effects with other Bluetooth stacks
that are not capable of handling unknown options.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Set general bonding security for ACL by default
This patch fixes double pairing issues with Secure Simple
Paring support. It was observed that when pairing with SSP
enabled, that the confirmation will be asked twice.
can: add the missing netlink get_xstats_size callback
This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Thu, 12 Nov 2009 01:35:01 +0000 (01:35 +0000)]
can: Fix driver Kconfig structure
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.
This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.
As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.
Thanks,
Oliver
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Tue, 10 Nov 2009 09:44:23 +0000 (09:44 +0000)]
s2io: fixing a ethtool test that is broken
Due commit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.
Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.
This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Wed, 11 Nov 2009 11:54:37 +0000 (11:54 +0000)]
sctp: Set socket source address when additing first transport
Recent commits
sctp: Get rid of an extra routing lookup when adding a transport
and
sctp: Set source addresses on the association before adding transports
changed when routes are added to the sctp transports. As such,
we didn't set the socket source address correctly when adding the first
transport. The first transport is always the primary/active one, so
when adding it, set the socket source address. This was causing
regression failures in SCTP tests.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
introduced a regression cought by the user regression test
suite. In particular, the API requires the user library to
re-allocate the buffer and could potentially trigger a SIGFAULT.
This change corrects that regression by passing the original
address buffer to the kernel unmodified, but still allows for
a returned association id.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 10 Nov 2009 08:57:34 +0000 (08:57 +0000)]
sctp: Set source addresses on the association before adding transports
Recent commit 8da645e101a8c20c6073efda3c7cc74eec01b87f
sctp: Get rid of an extra routing lookup when adding a transport
introduced a regression in the connection setup. The behavior was
different between IPv4 and IPv6. IPv4 case ended up working because the
route lookup routing returned a NULL route, which triggered another
route lookup later in the output patch that succeeded. In the IPv6 case,
a valid route was returned for first call, but we could not find a valid
source address at the time since the source addresses were not set on the
association yet. Thus resulted in a hung connection.
The solution is to set the source addresses on the association prior to
adding peers.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilpo Järvinen [Fri, 13 Nov 2009 21:56:33 +0000 (13:56 -0800)]
tcp: provide more information on the tcp receive_queue bugs
The addition of rcv_nxt allows to discern whether the skb
was out of place or tp->copied. Also catch fancy combination
of flags if necessary (sadly we might miss the actual causer
flags as it might have already returned).
Btw, we perhaps would want to forward copied_seq in
somewhere or otherwise we might have some nice loop with
WARN stuff within but where to do that safely I don't
know at this stage until more is known (but it is not
made significantly worse by this patch).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Wey-Yi Guy [Fri, 6 Nov 2009 23:17:04 +0000 (15:17 -0800)]
iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Tue, 10 Nov 2009 02:04:13 +0000 (18:04 -0800)]
Libertas: fix issues while configuring host sleep using ethtool wol
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Mon, 9 Nov 2009 22:56:06 +0000 (16:56 -0600)]
rtl8187: Fix sparse warnings
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Mon, 9 Nov 2009 02:59:01 +0000 (21:59 -0500)]
ath5k: add LED support for HP Compaq CQ60
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Mon, 9 Nov 2009 02:59:00 +0000 (21:59 -0500)]
ath5k: don't reset mcast filter when configuring the mode
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 7 Nov 2009 17:37:37 +0000 (18:37 +0100)]
b43: work around a locking issue in ->set_tim()
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 6 Nov 2009 00:23:01 +0000 (00:23 +0000)]
can: should not use __dev_get_by_index() without locks
bcm_proc_getifname() is called with RTNL and dev_base_lock
not held. It calls __dev_get_by_index() without locks, and
this is illegal (might crash)
Close the race by holding dev_base_lock and copying dev->name
in the protected section.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
hisax: remove bad udelay call to fix build error on ARM
The hisax ISDN driver fails to build on ARM with CONFIG_HISAX_ELSA:
| drivers/built-in.o: In function `modem_set_dial':
| drivers/isdn/hisax/elsa_ser.c:535: undefined reference to `__bad_udelay'
| drivers/isdn/hisax/elsa_ser.c:544: undefined reference to `__bad_udelay'
| drivers/built-in.o: In function `modem_set_init':
| drivers/isdn/hisax/elsa_ser.c:486: undefined reference to `__bad_udelay'
| [...]
According to the comment in arch/arm/include/asm/delay.h, __bad_udelay
is specifically designed on ARM to produce a build failure when udelay
is called with a value > 2000.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 6 Nov 2009 10:37:41 +0000 (10:37 +0000)]
ipip: Fix handling of DF packets when pmtudisc is OFF
RFC 2003 requires the outer header to have DF set if DF is set
on the inner header, even when PMTU discovery is off for the
tunnel. Our implementation does exactly that.
For this to work properly the IPIP gateway also needs to engate
in PMTU when the inner DF bit is set. As otherwise the original
host would not be able to carry out its PMTU successfully since
part of the path is only visible to the gateway.
Unfortunately when the tunnel PMTU discovery setting is off, we
do not collect the necessary soft state, resulting in blackholes
when the original host tries to perform PMTU discovery.
This problem is not reproducible on the IPIP gateway itself as
the inner packet usually has skb->local_df set. This is not
correctly cleared (an unrelated bug) when the packet passes
through the tunnel, which allows fragmentation to occur. For
hosts behind the IPIP gateway it is readily visible with a simple
ping.
This patch fixes the problem by performing PMTU discovery for
all packets with the inner DF bit set, regardless of the PMTU
discovery setting on the tunnel itself.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Fri, 6 Nov 2009 12:56:20 +0000 (12:56 +0000)]
ixgbe: fix traffic hangs on Tx with ioatdma loaded
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Fri, 6 Nov 2009 12:56:00 +0000 (12:56 +0000)]
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Fri, 6 Nov 2009 12:55:38 +0000 (12:55 +0000)]
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Tue, 3 Nov 2009 03:42:40 +0000 (03:42 +0000)]
macsonic: fix crash on PowerBook 520
No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 6 Nov 2009 02:07:32 +0000 (02:07 +0000)]
be2net: Bug fix to send config commands to hardware after netdev_register
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 6 Nov 2009 02:06:59 +0000 (02:06 +0000)]
be2net: fix to set proper flow control on resume
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Sat, 7 Nov 2009 02:08:32 +0000 (18:08 -0800)]
netfilter: xt_connlimit: fix regression caused by zero family value
Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all
instances of par->match->family were changed to par->family.
References: http://bugzilla.netfilter.org/show_bug.cgi?id=610 Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Date: Thu, 05 Nov 2009 15:59:16 +0100
From: Holger Schurig <holgerschurig@gmail.com>
To: linux-wireless@vger.kernel.org
Subject: BUG: oops when "rmmod ipw2200"
This happened on wireless-testing v2.6.32-rc6-41575-g5e68bfb. I
modprobed ipw2200, put it into monitor mode, used tshark a while to
monitor, then I stopped tshark, "ifconfig eth2 down" and finally
"rmmod ipw2200", and voila:
Eric Dumazet [Fri, 6 Nov 2009 08:50:39 +0000 (00:50 -0800)]
decnet: netdevice refcount leak
While working on device refcount stuff, I found a device refcount leak
through DECNET.
This nasty bug can be used to hold refcounts on any !DECNET netdevice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitezslav Samel discovered that since 2.6.30.4+ active FTP can not work
over NAT. The "cause" of the problem was a fix of unacknowledged data
detection with NAT (commit a3a9f79e361e864f0e9d75ebe2a0cb43d17c4272).
However, actually, that fix uncovered a long standing bug in TCP conntrack:
when NAT was enabled, we simply updated the max of the right edge of
the segments we have seen (td_end), by the offset NAT produced with
changing IP/port in the data. However, we did not update the other parameter
(td_maxend) which is affected by the NAT offset. Thus that could drift
away from the correct value and thus resulted breaking active FTP.
The patch below fixes the issue by *not* updating the conntrack parameters
from NAT, but instead taking into account the NAT offsets in conntrack in a
consistent way. (Updating from NAT would be more harder and expensive because
it'd need to re-calculate parameters we already calculated in conntrack.)
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge code assumes ethernet addressing, so be more strict in
the what is allowed. This showed up when GRE had a bug and was not
using correct address format.
Add some more comments for increased clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
introduced the first reference to __devexit in struct virtio_driver
virtio_net which upset modpost ("Section mismatch in reference from the
variable virtio_net to the function .devexit.text:virtnet_remove()").
Fix this by renaming virtio_net to virtio_net_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by: Michael S. Tsirkin <mst@redhat.com> Blame-taken-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger [Wed, 4 Nov 2009 06:00:25 +0000 (00:00 -0600)]
rtl8187: Fix kernel oops when device is removed when LEDS enabled
As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops. There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.
This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb. My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.
(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Rick Farina <sidhayn@gmail.com> Tested-by: Rick Farina <sidhayn@gmail.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Wed, 4 Nov 2009 16:31:59 +0000 (08:31 -0800)]
isdn: hfc_usb: Fix read buffer overflow
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Wed, 4 Nov 2009 16:31:19 +0000 (08:31 -0800)]
isdn: hisax: Fix test in waitforxfw
The negation makes it a bool before the comparison and hence it
will never be 0x40.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 4 Nov 2009 16:27:09 +0000 (08:27 -0800)]
misdn: Fix reversed 'if' in st_own_ctrl
The current code probably returns -EINVAL a lot. Otherwise it would oops.
Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Wed, 4 Nov 2009 16:25:57 +0000 (08:25 -0800)]
isdn: hisax: Fix lock imbalance.
Add omittted unlocks to 2 functions.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Karsten Keil <Karsten-Keil@t-online.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Sun, 1 Nov 2009 18:25:40 +0000 (19:25 +0100)]
mac80211: check interface is down before type change
For some strange reason the netif_running() check
ended up after the actual type change instead of
before, potentially causing all kinds of problems
if the interface is up while changing the type;
one of the problems manifests itself as a warning:
WARNING: at net/mac80211/iface.c:651 ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]()
Hardware name: Aspire one
Pid: 2596, comm: wpa_supplicant Tainted: G W 2.6.31-10-generic #32-Ubuntu
Call Trace:
[] warn_slowpath_common+0x6d/0xa0
[] warn_slowpath_null+0x15/0x20
[] ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]
[] ieee80211_if_change_type+0x4a/0xc0 [mac80211]
[] ieee80211_change_iface+0x61/0xa0 [mac80211]
[] cfg80211_wext_siwmode+0xc7/0x120 [cfg80211]
[] ioctl_standard_call+0x58/0xf0
Cc: Arjan van de Ven <arjan@infradead.org> Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
introduced a potential NULL pointer dereference that
some people have been hitting for some reason -- the
params.bssid pointer is not guaranteed to be non-NULL
for what seems to be a race between various ways of
reaching the same thing.
While I'm trying to analyse the problem more let's
first fix the crash. I think the real fix may be to
avoid doing _anything_ if it ended up being NULL, but
right now I'm not sure yet.
I think
http://bugzilla.kernel.org/show_bug.cgi?id=14342
might also be this issue.
Reported-by: Parag Warudkar <parag.lkml@gmail.com> Tested-by: Parag Warudkar <parag.lkml@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Woodhouse [Fri, 30 Oct 2009 17:45:14 +0000 (17:45 +0000)]
libertas if_usb: Fix crash on 64-bit machines
On a 64-bit kernel, skb->tail is an offset, not a pointer. The libertas
usb driver passes it to usb_fill_bulk_urb() anyway, causing interesting
crashes. Fix that by using skb->data instead.
This highlights a problem with usb_fill_bulk_urb(). It doesn't notice
when dma_map_single() fails and return the error to its caller as it
should. In fact it _can't_ currently return the error, since it returns
void.
So this problem was showing up only at unmap time, after we'd already
suffered memory corruption by doing DMA to a bogus address.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Oct 2009 09:09:28 +0000 (10:09 +0100)]
mac80211: fix reason code output endianness
When HT debugging is enabled and we receive a DelBA
frame we print out the reason code in the wrong byte
order. Fix that so we don't get weird values printed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
downgraded an ASSERT to a WARN_ON() but also misplaced a
semicolon at the end of the second check. What this did
was force the rate control code to always return the rate
even if we should have warned about it. Since this should
not have happened anymore anyway this fix isn't critical
as the proper rate would have been returned anyway.
Cc: stable@kernel.org Reported-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 28 Oct 2009 21:08:13 +0000 (22:08 +0100)]
b43: Fix DMA TX bounce buffer copying
b43 allocates a bouncebuffer, if the supplied TX skb is in an invalid
memory range for DMA.
However, this is broken in that it fails to copy over some metadata to the
new skb.
This patch fixes three problems:
* Failure to adjust the ieee80211_tx_info pointer to the new buffer.
This results in a kmemcheck warning.
* Failure to copy the skb cb, which contains ieee80211_tx_info, to the new skb.
This results in breakage of various TX-status postprocessing (Rate control).
* Failure to transfer the queue mapping.
This results in the wrong queue being stopped on saturation and can result in queue overflow.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Tested-by: Christian Casteyde <casteyde.christian@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 15 Oct 2009 06:50:28 +0000 (14:50 +0800)]
ipw2200: fix oops on missing firmware
For non-monitor interfaces, the syntax for alloc_ieee80211/free_80211
is wrong. Because alloc_ieee80211 only creates (wiphy_new) a wiphy, but
free_80211() does wiphy_unregister() also. This is only correct when
the later wiphy_register() is called successfully, which apparently
is not the case for your fw doesn't exist one.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu [Fri, 30 Oct 2009 05:51:48 +0000 (05:51 +0000)]
gre: Fix dev_addr clobbering for gretap
Nathan Neulinger noticed that gretap devices get their MAC address
from the local IP address, which results in invalid MAC addresses
half of the time.
This is because gretap is still using the tunnel netdev ops rather
than the correct tap netdev ops struct.
This patch also fixes changelink to not clobber the MAC address
for the gretap case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Nathan Neulinger <nneul@mst.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 30 Oct 2009 05:03:53 +0000 (05:03 +0000)]
net: fix sk_forward_alloc corruption
On UDP sockets, we must call skb_free_datagram() with socket locked,
or risk sk_forward_alloc corruption. This requirement is not respected
in SUNRPC.
Add a convenient helper, skb_free_datagram_locked() and use it in SUNRPC
Reported-by: Francis Moreau <francis.moro@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 29 Oct 2009 13:46:05 +0000 (13:46 +0000)]
e1000e: rework disable K1 at 1000Mbps for 82577/82578
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 29 Oct 2009 13:45:45 +0000 (13:45 +0000)]
e1000e: config PHY via software after resets
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 29 Oct 2009 13:42:41 +0000 (13:42 +0000)]
e100: e100_phy_init() isolates selected PHY, causes 10 second boot delay
A change in how PHYs are electrically isolated caused all PHYs to be
isolated followed by reverting that isolation for the selected PHY.
Unfortunately, isolating the selected PHY for even a short period of
time can result in DHCP negotiation taking more than 10 seconds on certain
embedded configurations delaying boot time as reported by Bernhard Kaindl.
This patch reverts the change to how PHYs are isolated yet still works
around the issue for 82552 needing the selected PHY's BMCR register to
be written after the unused PHYs are isolated. This code is moved below
the setting of nic->phy ID in order to do the 82552-specific workaround.
Cc: Bernhard Kaindl <bernhard.kaindl@gmx.net> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gabor Gombas [Thu, 29 Oct 2009 10:19:11 +0000 (03:19 -0700)]
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
Currently PACKET_TX_RING forces certain amount of every frame to remain
unused. This probably originates from an early version of the
PACKET_TX_RING patch that in fact used the extra space when the (since
removed) CONFIG_PACKET_MMAP_ZERO_COPY option was enabled. The current
code does not make any use of this extra space.
This patch removes the extra space reservation and lets userspace make
use of the full frame size.
Signed-off-by: Gabor Gombas <gombasg@sztaki.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log