Eric Nelson [Wed, 23 Sep 2015 14:07:08 +0000 (11:07 -0300)]
[media] rc: gpio-ir-recv: add timeout on idle
Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.
Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.
This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.
The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com> Acked-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] media: st-rc: remove misuse of IRQF_NO_SUSPEND flag
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
In file included from drivers/media/i2c/s5c73m3/s5c73m3-spi.c:22:0:
drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:40: error: expected ')' before ';' token
MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids;);
^
Peter Griffin [Thu, 3 Sep 2015 17:59:53 +0000 (14:59 -0300)]
[media] c8sectpfe: Update DT binding doc with some minor fixes
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Peter Griffin [Thu, 3 Sep 2015 17:59:52 +0000 (14:59 -0300)]
[media] c8sectpfe: Update binding to reset-gpios
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] s5c73m3: Export OF module alias information
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/media/pci/ddbridge/ddbridge-core.c:89
incorrect check for negative return
Return type of wait_event_timeout is signed long not int and the
return type is >=0 always thus the negative check is unnecessary..
As stat is used here exclusively its type is simply changed and the
negative return check dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Josh Wu [Tue, 3 Nov 2015 05:45:08 +0000 (03:45 -0200)]
[media] atmel-isi: correct yuv swap according to different sensor outputs
we need to configure the YCC_SWAP bits in ISI_CFG2 according to current
sensor output and Atmel ISI output format.
Current there are two cases Atmel ISI supported:
1. Atmel ISI outputs YUYV format.
This case we need to setup YCC_SWAP according to sensor output
format.
2. Atmel ISI output a pass-through formats, which means no swap.
Just setup YCC_SWAP as default with no swap.
Josh Wu [Wed, 28 Oct 2015 09:48:55 +0000 (07:48 -0200)]
[media] v4l2-clk: v4l2_clk_get() also need to find the of_fullname clock
The soc-camera host will be probed and register a v4l2_clk, but if at
that moment, the i2c device is not available, then the registered
v4l2_clk name is an OF string not a I2C string.
So when i2c sensor probes and calls v4l2_clk_get(), it only searches a
clock with I2C string, like "1-0030".
This patch will search the clock with OF string name if no clock with
I2C string name could be found.
[media] vivid: add support for reduced frame rate in video capture
With this patch, vivid capture thread can now generate a video with
frame rate reduced by a factor of 1000 / 1001. This option can be
selected using a control Reduced Framerate from gui.
[media] vivid: add support for reduced fps in video out
If reduced fps flag is set then check if other necessary conditions
are true for the given bt timing. If yes, then reduce the frame rate.
For vivid transmitter, timeperframe_vid_out controls the frame rate.
Adjusting the timeperframe_vid_out by scaling down pixel clock by
factor of 1000 / 1001.
[media] v4l2-dv-timings: add condition checks for reduced fps
Added a helper function to check necessary conditions required for
reduced fps. The reduced fps is supported for CVT and CEA861 timings.
CVT supports reduced fps only if reduced blanking v2 (indicated by
vsync = 8) is true. Whereas CEA861 supports reduced fps if
V4L2_DV_FL_CAN_REDUCE_FPS flag is true.
Tommi Franttila [Thu, 12 Nov 2015 09:01:07 +0000 (07:01 -0200)]
[media] v4l2-device: Don't unregister ACPI/Device Tree based devices
When a V4L2 sub-device backed by a DT or ACPI based device was removed,
the device was unregistered as well which certainly was not intentional,
as the client device would not be re-created by simply reinstating the
V4L2 sub-device (indeed the device would have to be there first!).
Skip unregistering the device in case it has non-NULL of_node or fwnode.
Signed-off-by: Tommi Franttila <tommi.franttila@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ulrich Hecht [Tue, 10 Nov 2015 13:39:00 +0000 (11:39 -0200)]
[media] media: adv7180: increase delay after reset to 5ms
Initialization of the ADV7180 chip fails on the Renesas R8A7790-based
Lager board about 50% of the time. This patch resolves the issue by
increasing the minimum delay after reset from 2 ms to 5 ms, following the
recommendation in the ADV7180 datasheet:
"Executing a software reset takes approximately 2 ms. However, it is
recommended to wait 5 ms before any further I2C writes are performed."
Arnd Bergmann [Fri, 16 Oct 2015 00:35:40 +0000 (21:35 -0300)]
[media] sh-vou: clarify videobuf2 dependency
The sh-vou driver has been converted from videobuf to videobuf2, but
the Kconfig file still lists VIDEOBUF_DMA_CONTIG as a dependency.
Consequently we can build the driver without VIDEOBUF2_DMA_CONTIG
and get a link error:
drivers/built-in.o: In function `sh_vou_probe':
vf610-ocotp.c:(.text+0x2dbf5c): undefined reference to `vb2_dma_contig_init_ctx'
vf610-ocotp.c:(.text+0x2dc0b4): undefined reference to `vb2_dma_contig_cleanup_ctx'
vf610-ocotp.c:(.text+0x2dc144): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `sh_vou_remove':
vf610-ocotp.c:(.text+0x2dc190): undefined reference to `vb2_dma_contig_cleanup_ctx'
This changes the dependency to VIDEOBUF2_DMA_CONTIG instead.
Fixes: 57af3ad59d95 ("[media] sh-vou: convert to vb2") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] media: fix waitqueue_active without memory barrier in cpia2 driver
cpia2_usb_disconnect() seems to be missing a memory barrier which might
cause the waker to not notice the waiter and miss sending a wake_up as
in the following figure.
cpia2_usb_disconnect sync
------------------------------------------------------------------------
mutex_unlock(&cam->v4l2_lock);
if (waitqueue_active(&cam->wq_stream))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
/* wait_event_interruptible */
/* __wait_event_interruptible */
/* ___wait_event */
long __int = prepare_to_wait_event(
&wq, &__wait, state);
if (!cam->streaming ||
frame->status == FRAME_READY)
cam->curbuff->status = FRAME_READY;
cam->curbuff->length = 0;
schedule()
------------------------------------------------------------------------
The attached patch removes the call to waitqueue_active() leaving just
wake_up() behind. This fixes the problem because the call to
spin_lock_irqsave() in wake_up() will be an ACQUIRE operation.
I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Antonio Ospite [Fri, 2 Oct 2015 20:33:13 +0000 (17:33 -0300)]
[media] gspca: ov534/topro: prevent a division by 0
v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:
Following what the doc says about a zeroed timeperframe (see
http://www.linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-parm.html):
...
To reset manually applications can just set this field to zero.
fix the issue by resetting the frame rate to a default value in case of
an unusable timeperframe.
The fix is done in the subdrivers instead of gspca.c because only the
subdrivers have notion of a default frame rate to reset the camera to.
Signed-off-by: Antonio Ospite <ao2@ao2.it> Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dan Carpenter [Tue, 10 Nov 2015 22:22:49 +0000 (20:22 -0200)]
[media] av7110: don't allow negative volumes
The issue here is that we there is a static checker warning because we
have a user controlled volume setting and we cap the upper bound but we
allow negative numbers. Negative volumes don't make sense, so let's
make these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Thu, 29 Oct 2015 05:02:06 +0000 (03:02 -0200)]
[media] vb2: fix a regression in poll() behavior for output,streams
In the 3.17 kernel the poll() behavior changed for output streams:
as long as not all buffers were queued up poll() would return that
userspace can write. This is fine for the write() call, but when
using stream I/O this changed the behavior since the expectation
was that it would wait for buffers to become available for dequeuing.
This patch only enables the check whether you can queue buffers
for file I/O only, and skips it for stream I/O.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: <stable@vger.kernel.org> # for v3.17 and up Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Thu, 29 Oct 2015 04:59:37 +0000 (02:59 -0200)]
[media] vivid: fix compliance error
If vivid is loaded with the no_error_inj=1 option, then v4l2-compliance will
fail for the video and vbi output nodes because the vivid control class has no
controls.
Don't add the control class for video and vbi output if no_error_inj is true.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The term "input stream" is confusing since it is not clear whether this is an
input stream from the point of view of the application or from the point of
view of the hardware. So replace it with the more standard term "capture stream".
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver can only be built when VIDEO_V4L2_SUBDEV_API
and VIDEO_DAVINCI_VPBE_DISPLAY are also provided by the
kernel.
drivers/staging/media/davinci_vpfe/dm365_isif.c: In function '__isif_get_format':
drivers/staging/media/davinci_vpfe/dm365_isif.c:1410:3: error: implicit declaration of function 'v4l2_subdev_get_try_format' [-Werror=implicit-function-declaration]
return v4l2_subdev_get_try_format(fh, pad);
^
Julia Lawall [Tue, 29 Jul 2014 15:16:43 +0000 (12:16 -0300)]
[media] drivers/staging/media/davinci_vpfe/vpfe_mc_capture.c: use correct structure type name in sizeof
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
[media] include/media: move platform_data to linux/platform_data/media
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
[media] include/media: split I2C headers from V4L2 core
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Alec Leamas [Thu, 12 Nov 2015 18:03:00 +0000 (16:03 -0200)]
[media] bz#75751: Move internal header file lirc.h to uapi/
The file include/media/lirc.h describes a public interface and
should thus be a public header. See kernel bug
https://bugzilla.kernel.org/show_bug.cgi?id=75751 which has
a manpage describing the interface + an acknowledgment that this
info belongs to uapi.
Graham Whaley [Thu, 12 Nov 2015 20:51:51 +0000 (18:51 -0200)]
[media] DocBook/media/Makefile: Do not fail mkdir if dir already exists
Commit 5240f4e68d42 ("[media] DocBook/media/Makefile: Avoid make htmldocs
to fail") introduced a mkdir which is always called through
install_media_images from the Documentation/DocBook/Makefile htmldocs rule.
If you run 'make htmldocs' more than once you get:
[media] dvb_frontend: get rid of set_state ops & related data
The get_state()/set_state and the corresponding data types
(struct tuner_state and enum tuner_param) are old DVB interfaces
that came from the DVBv3 time.
Nowadays, set_params() provide a better way to set the tuner
and demod parameters. So, no need to keep those legacy stuff,
as all drivers that were using it got converted.
With this patch, all kABI elements at dvb_frontend.h are now
documented.
[media] stb6100: get rid of get_state()/set_state()
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
[media] tda8261: don't use set_state/get_state callbacks
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
[media] tda665x: split set_frequency from set_state
On tda665x, set_state only sets frequency. As the kABI for set_state
is meant to be used only on special cases, split the function
into two, in order to allow it to be latter used by a DVBv5
cache params logic.
[media] stb6100: get rid of tuner_state at struct stb6100_state
The stb6100 driver has a struct tuner_state on its state
struct, that it is used only to store the bandwidth. Even so,
this struct is not really used, as every time the bandwidth
is get or set, it goes through the hardware.
[media] dvb_frontend.h: get rid of unused tuner params/states
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
[media] demux.h: Some documentation fixups for the header
The DocBook description of this header has two issues:
- It calls the Kernel ABI as API, instead of kABI;
- It mentions that the DVB frontend kABI is not described
within the document. As this will actually generate a
single DocBook, this is actually not true, now that
the documentation for the frontend was added.
[media] dvb_frontend.h: Add a description for the header
This header file provides the kABI functions used by the
Digital TV Frontend core support. Add a description for
this kABI, to add at the device_drivers Kernel DocBook.
This function is used mainly at the DVB core, in order to provide
emulation for a legacy ioctl. The only current exception is
the stv0299 driver, with takes more than 8ms to switch voltage,
breaking the emulation for FE_DISHNETWORK_SEND_LEGACY_CMD.
* tag 'v4.4-rc1': (12900 commits)
Linux 4.4-rc1
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
f2fs: xattr simplifications
squashfs: xattr simplifications
9p: xattr simplifications
xattr handlers: Pass handler to operations instead of flags
jffs2: Add missing capability check for listing trusted xattrs
hfsplus: Remove unused xattr handler list operations
ubifs: Remove unused security xattr handler
vfs: Fix the posix_acl_xattr_list return value
vfs: Check attribute names in posix acl xattr handers
mpt3sas: fix inline markers on non inline function declarations
dax: fix __dax_pmd_fault crash
Revert "drm/rockchip: Convert the probe function to the generic drm_of_component_probe()"
drm: Don't oops in drm_calc_timestamping_constants() if drm_vblank_init() wasn't called
ALSA: pci: depend on ZONE_DMA
...
Linus Torvalds [Sun, 15 Nov 2015 17:36:24 +0000 (09:36 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Mostly updates to the perf tool plus two fixes to the kernel core code:
- Handle tracepoint filters correctly for inherited events (Peter
Zijlstra)
- Prevent a deadlock in perf_lock_task_context (Paul McKenney)
- Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
Melo)
- Print full source file paths when using 'perf annotate --print-line
--full-paths' (Michael Petlan)
- Fix 'perf probe -d' when just one out of uprobes and kprobes is
enabled (Wang Nan)
- Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)
- Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
the 'perf test' LLVM entries, when running it in-tree, to
.gitignore (Yunlong Song)
- libbpf error reporting improvements, using a strerror interface to
more precisely tell the user about problems with the provided
scriptlet, be it in C or as a ready made object file (Wang Nan)
- Do not be case sensitive when searching for matching 'perf test'
entries (Arnaldo Carvalho de Melo)
- Inform the user about objdump failures in 'perf annotate' (Andi
Kleen)
- Improve the LLVM 'perf test' entry, introduce a new ones for BPF
and kbuild tests to check the environment used by clang to compile
.c scriptlets (Wang Nan)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
tools include: Add compiler.h to list.h
perf probe: Verify parameters in two functions
perf session: Add missing newlines to some pr_err() calls
perf annotate: Support full source file paths for srcline fix
perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
perf: Fix inherited events vs. tracepoint filters
perf: Disable IRQs across RCU RS CS that acquires scheduler lock
perf test: Do not be case sensitive when searching for matching tests
perf test: Add 'perf test BPF'
perf test: Enhance the LLVM tests: add kbuild test
perf test: Enhance the LLVM test: update basic BPF test program
perf bpf: Improve BPF related error messages
perf tools: Make fetch_kernel_version() publicly available
bpf tools: Add new API bpf_object__get_kversion()
bpf tools: Improve libbpf error reporting
perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
perf annotate: Inform the user about objdump failures in --stdio
perf stat: Make stat options global
perf sched latency: Fix thread pid reuse issue
...
Linus Torvalds [Sun, 15 Nov 2015 17:34:32 +0000 (09:34 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull liblockdep fixes from Thomas Gleixner:
"Three small patches to synchronize liblockdep with the latest core
changes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: explicitly declare lockdep API we call from liblockdep
tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
tools/liblockdep: remove task argument from debug_check_no_locks_held
Linus Torvalds [Sun, 15 Nov 2015 17:32:59 +0000 (09:32 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes and updates related to x86:
- Fix the W+X check regression on XEN
- The real fix for the low identity map trainwreck
- Probe legacy PIC early instead of unconditionally allocating legacy
irqs
- Add cpu verification to long mode entry
- Adjust the cache topology to AMD Fam17H systems
- Let Merrifield use the TSC across S3"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Call verify_cpu() after having entered long mode too
x86/setup: Fix low identity map for >= 2GB kernel range
x86/mm: Skip the hypervisor range when walking PGD
x86/AMD: Fix last level cache topology for AMD Fam17h systems
x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
Linus Torvalds [Sun, 15 Nov 2015 17:10:53 +0000 (09:10 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Linus Torvalds [Sat, 14 Nov 2015 17:43:00 +0000 (09:43 -0800)]
Merge tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc"
* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pci: depend on ZONE_DMA
ALSA: hda - Simplify phantom jack handling for HDMI/DP
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
ALSA: ctxfi: constify rsc ops structures
ALSA: usb: Add native DSD support for Aune X1S
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
sound: fix check for error condition of register_chrdev()
Linus Torvalds [Sat, 14 Nov 2015 17:09:37 +0000 (09:09 -0800)]
Merge tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Found a couple of brown paper bag bugs with the prev pull request
(including a SMP build breakage report from Guenter). Since these are
urgent I also decided to send over a bunch of other pending fixes
which could have otherwise waited an rc or two.
Summary:
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
failure)
- cpu_relax() now compiler barrier for UP as well
- handling of userspace Bus Errors for ARCompact builds"
* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
ARCv2: lib: memcpy: use local symbols
Vineet Gupta [Mon, 9 Nov 2015 12:18:34 +0000 (17:48 +0530)]
ARC: cpu_relax() to be compiler barrier even for UP
cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.
Vineet Gupta [Fri, 30 Oct 2015 19:52:51 +0000 (01:22 +0530)]
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)
- So move mem_service exception handler from common code into ARCv2 code.
- In ARCompact code, define mem_service as L2 interrupt handler which
just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com> Tested-by: Ana Martins <amartins@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Sat, 14 Nov 2015 05:53:18 +0000 (21:53 -0800)]
Merge tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's the branch of chrome platform changes for v4.4. Some have been
queued up for the full 4.3 release cycle since I forgot to send them
in for that round (rebased early on to deal with fixes conflicts).
Most of these enable EC communication stuff -- Pixel 2015 support,
enabling building for ARM64 platforms, and a few fixes for memory
leaks.
There's also a patch in here to allow reading/writing the verified
boot context, which depends on a sysfs patch acked by Greg"
* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: Fix i2c-designware adapter name
platform/chrome: Support reading/writing the vboot context
sysfs: Support is_visible() on binary attributes
platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
platform/chrome: cros_ec: Fix leak in sequence_store()
platform/chrome: Enable Chrome platforms on 64-bit ARM
platform/chrome: cros_ec_dev - Add a platform device ID table
platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
platform/chrome: cros_ec_lpc - Use existing function to check EC result
platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"
Linus Torvalds [Sat, 14 Nov 2015 05:47:06 +0000 (21:47 -0800)]
Merge tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull another x86 platform driver update from Darren Hart:
"Support for the unfortunately rather unique ESC key on the Ideapad
Yoga 3 and two DMI matches for rfkill support. Solitary fix for
potential missed errors for asus-wmi. Downgrade a thinkpad_acpi
message to info.
asus-wmi:
- fix error handling in store_sys_wmi()
ideapad-laptop:
- Add Lenovo Yoga 900 to no_hw_rfkill dmi list
- include Yoga 3 1170 in add rfkill whitelist
- add support for Yoga 3 ESC key
thinkpad_acpi:
- Don't yell on unsupported brightness interfaces"
* tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
asus-wmi: fix error handling in store_sys_wmi()
ideapad-laptop: Add Lenovo Yoga 900 to no_hw_rfkill dmi list
ideapad-laptop: include Yoga 3 1170 in add rfkill whitelist
ideapad-laptop: add support for Yoga 3 ESC key
thinkpad_acpi: Don't yell on unsupported brightness interfaces
Linus Torvalds [Sat, 14 Nov 2015 05:41:14 +0000 (21:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"An update to the tsc2005 driver that allows it to also support tsc2004
(basically the same controller, but uses i2c instead of spi bus), and
a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: parkbd - drop bogus __init from parkbd_allocate_serio()
Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
Input: tsc2004 - add support for tsc2004
Input: tsc200x-core - rename functions and variables
Input: tsc2005 - separate SPI and core functions
Linus Torvalds [Sat, 14 Nov 2015 04:35:54 +0000 (20:35 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...