Ilan Elias [Sun, 18 Sep 2011 08:19:35 +0000 (11:19 +0300)]
NFC: basic NCI protocol implementation
The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.
Signed-off-by: Ilan Elias <ilane@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: Do not allow disabled channel in scan request
cfg80211_conn_scan allows disabled channels at scan request.
Hence probe request was seen at the disabled one. This patch
ensures that disabled channel never be added into the scan
request's channel list.
Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 16 Sep 2011 11:45:25 +0000 (13:45 +0200)]
cfg80211: validate IBSS BSSID
The IBSS BSSID is never validated, so an
invalid one might end up being used. Fix
this by rejecting invalid configuration.
Reported-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fix regression on queue stop during 2040 bss change
The commit "mac80211: stop tx before doing hw config and
rate update" stops the tx queue and call drv_flush so frequently
whenever a beacon got received with 11n htcap. This leads to
massive "Failed to stop TX DMA" logspam on embedded hw. So the
queue stop and flush should be called if and only if there is a
change in the channel type.
Reported-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:52 +0000 (11:46 -0700)]
iwlagn: do not use interruptible waits
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: stable@kernel.org [2.6.24+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 15 Sep 2011 18:46:51 +0000 (11:46 -0700)]
iwlagn: use iwl_eeprom_calib_hdr structure
For retrieve calibration hdr related information, instead of using structure in
one place and #define in other place, unify the method to use data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:49 +0000 (11:46 -0700)]
iwlagn: remove drvdata support from bus layer
Since the removal of the sysfs files, it is no
longer necessary to have upper layers control
the drvdata, so let the PCI driver have it for
itself completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:48 +0000 (11:46 -0700)]
iwlagn: move sysfs files to debugfs
The debug_level and temperature files should be in
debugfs, the txpower file is completely unneeded
since TX power can be set with iw/iwconfig.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:47 +0000 (11:46 -0700)]
iwlagn: remove unused function declarations
iwl_suspend and iwl_resume don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:46 +0000 (11:46 -0700)]
iwlagn: rename iwl-pci.h to iwl-cfg.h
There's nothing PCI(E) specific in this file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:45 +0000 (11:46 -0700)]
iwlagn: clean up PM code
The transport callbacks might as well be undefined
when CONFIG_PM_SLEEP is not set, so ifdef all of
it out and make everything available for PM_SLEEP
only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:44 +0000 (11:46 -0700)]
iwlagn: Makefile whitespace cleanup
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:43 +0000 (11:46 -0700)]
iwlagn: generically provide iwl_trans_send_cmd_pdu
There's no need to have the transport layer have a
callback for iwl_trans_send_cmd_pdu() since it is
just a generic wrapper around iwl_trans_send_cmd().
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Sep 2011 18:46:42 +0000 (11:46 -0700)]
iwlagn: move PCI-E transport files
Move all the PCI-E specific transport files to
be iwl-trans-pcie*; specifically iwl-trans.c
which is really iwl-trans-pcie.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
From time to time, we hit a WARN_ON in iwl_mac_remove_interface.
This basically means that we got out of sync with mac80211: the vif
we hold differs from the vif 80211 passes as parameter. Try to get
some data that will help to debug this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Thu, 15 Sep 2011 18:46:39 +0000 (11:46 -0700)]
iwlagn: replace beacon_time_fsf_bits variable with #define
All devices use the same value for beacon_time_tsf_bits. Use the #define
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
chain_noise_num_beacons is set and never changes. Use the #define
rather than 3 levels of indirection.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fry, Donald H [Thu, 15 Sep 2011 18:46:37 +0000 (11:46 -0700)]
iwlagn: fix modinfo display for 135 ucode.
The modinfo report for 135 ucode is iwlwifi-135-IWL135_UCODE_API_MAX.ucode
Change to show the value of the define: iwlwifi-135-6.ucode
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 15 Sep 2011 19:47:26 +0000 (12:47 -0700)]
iwlagn: Convert kzalloc to kcalloc
Convert kzalloc to kcalloc, coalesce multiple lines too.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation to the bus layer API - iwl-bus.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: use enum iwl_rxon_context_id instead of u8
enum iwl_rxon_context_id is the right type to use when we need a
rxon_context_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move iwl_stop / wake_queue to the upper layer
Add a wrapper in the upper layer to call the mac80211's function.
This allows not to have the transport layer call mac80211 directly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: free the Tx cmd when a non empty Tx queue is freed
When a non-empty Tx queueis freed, the buffer it contains must be
freed too. Since the Tx cmd are now allocated from a pool, the Tx
cmd must be freed too.
This patch avoids to destroy a non-empty pool of Tx cmd.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver is unloaded while there is still a host command in
flight, its tfd will be freed by iwl_tx_queue_free.
This function is called for both types of queues: Tx queues and cmd
queue. This didn't take in count the fact that in Tx queues, tfds are
mapped as TO_DEVICE (besides the first TB), whereas in cmd queue, all
TBs are mapped as BIDI.
Hence, tx_queue_free unmapped the second (and higher) TB of each tfd
in the cmd queue as TO_DEVICE, whereas they must be freed as BIDI.
This means that if a multi TFD is in flight while we unload the
driver (which is quite unlikely but can happen), we will get the
warning below.
Reported-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: warn about buggy fw that doesn't set SEQ_RX_FRAME
The way we check if there is host command that should be reclaimed is
way too complicated. We should have a clear indication from the fw.
The fw is expected to set the SEQ_RX_FRAME bit if the frame was
originated by the fw which indicates to the driver that there is no
host command to free.
Somehow, there seem to have been buggy fw out there, hence the very
old comment.
This code checks if we have still buggy fw out there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, the caldata continues to retain older history
values learned on that channel. It is always safer to start
noise floor calibration from the defaults after the assoication.
So this patch resets the nf history buffer when none of the
STA vifs are associated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: load noise floor from history after the full chip reset
Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.
Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 15 Sep 2011 12:25:37 +0000 (14:25 +0200)]
ath9k_hw: fix setting the hardware diversity flag
ath9k_hw_set_diversity is only called from init.c where it cannot affect
the hardware setting because it's cleared on the next reset.
Instead of using a PHY op for something that's supposed to be initialized
statically, set the register value directly in the INI override function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 15 Sep 2011 12:25:35 +0000 (14:25 +0200)]
ath9k_hw: clean up hardware revision checks
- AR_SREV_5416_20_OR_LATER is always true, remove it
- AR_SREV_9280_20_OR_LATER is always true within eeprom_4k.c and eeprom_9287.c
- (AR_SREV_9271 || AR_SREV_9285) is always true in eeprom_4k.c
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add function to find vendor-specific ie (along with
vendor-specific ie struct definition and P2P OUI values)
Signed-off-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Chen Ganir [Tue, 30 Aug 2011 10:58:28 +0000 (13:58 +0300)]
Bluetooth: Fixed BT ST Channel reg order
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.
Signed-off-by: Chen Ganir <chen.ganir@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Kalle Valo [Tue, 13 Sep 2011 07:21:25 +0000 (10:21 +0300)]
MAINTAINERS: update ath6kl
It's not in staging anymore and I'm the current maintainer.
Cc: Luis R. Rodriguez <mcgrof@gmail.com> Cc: Naveen Singh <nvesing@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:24:27 +0000 (21:24 +0200)]
ath9k: do not insert padding into tx buffers on AR9380+
With the new EDMA descriptor format, a single descriptor can contain up
to four buffer pointers. By splitting the buffer into two parts, we can
let the hardware add the padding internally instead of using memmove on
the skb data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:24:26 +0000 (21:24 +0200)]
ath9k: optimize ath_tx_rc_status usage
The only flag that needs to be set when ath_tx_rc_status is called with
rc_update == false is the IEEE80211_TX_STAT_TX_FILTERED flag. All other
data is ignored in that case.
This flag can be set from ath_tx_complete_buf instead, so that we can
drop a few redundant calls to ath_tx_rc_status and remove the rc_update
function parameter
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:24:24 +0000 (21:24 +0200)]
ath9k: optimize ath9k_ps_restore
ath_hw_cycle_counters_update only needs to be called if the power state
changes. Most of the time this does not happen, even when ps_usecount
goes down to 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:24:22 +0000 (21:24 +0200)]
ath9k: use the new API for setting tx descriptors
With the new API, tx descriptors can be written in one single pass
instead of having to re-read and rewrite fields from multiple places.
This makes the code easier to read and also slightly improves performance
on embedded MIPS hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:24:21 +0000 (21:24 +0200)]
ath9k_hw: add a new API for setting tx descriptors
Instead of using lots of different functions with long argument lists,
pull all the necessary information from one struct. This makes the code
easier to read and eliminates the need for copying data between multiple
linked descriptors.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:23:03 +0000 (21:23 +0200)]
ath9k: ensure that rx is not enabled during a reset
During a reset, rx buffers are flushed after rx has been disabled. To avoid
race conditions, rx needs to stay disabled during the reset, so avoid any
calls to ath9k_hw_rxena in that case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 14 Sep 2011 19:23:02 +0000 (21:23 +0200)]
ath9k: make beacon timer initialization more reliable
When starting the AP beacon timer, it assumes that the TSF has recently
been cleared. Set the SC_OP_TSF_RESET flag to ensure that this is always
the case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Do full chip reset on 11A channels for AR9003
AR9003 seems to have issues sometimes with fast channel change
in 5GHz and this case is handled specifically for AR9280 by doing
a full reset. Let's do a full reset for 5GHz channles of AR9380
& for all channels of AR9280 pci chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Thu, 15 Sep 2011 15:36:22 +0000 (08:36 -0700)]
iwlagn: workaround bug crashing some APs
This patch reverts commit 9b7688328422b88a7a15dc0dc123ad9ab1a6e22d which
was introduced in 2.6.38-rc1. It works around a problem where the iwlagn
driver stimulates a bug crashing (requiring power cycle to recover) some
APs under heavy traffic.
CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by: Don Fry <donald.h.fry@intel.com> SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan request received from cfg80211_connect do not
have proper rate mast. So the probe request sent on each
channel do not have proper the supported rates ie.
Cc: stable@kernel.org Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 14 Sep 2011 21:50:23 +0000 (16:50 -0500)]
rtl2800usb: Fix incorrect storage of MAC address on big-endian platforms
The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 14 Sep 2011 21:50:22 +0000 (16:50 -0500)]
rt2800pci: Fix compiler error on PowerPC
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix suspend/resume races with unregister hw
Above commit add rtnl_lock() into wiphy_register(), what cause deadlock
when initializing ipw2x00 driver, which itself call wiphy_register()
from register_netdev() internal callback with rtnl mutex taken.
To fix move wiphy_register() outside register_netdev(). This solution
have side effect of not creating /sys/class/net/wlanX/phy80211 link,
but that's a minor issue we can live with.
Bisected-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Bisected-by: Michael Witten <mfwitten@gmail.com> Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Tested-by: Michael Witten <mfwitten@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: Reset beacon_found while updating regulatory
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andres Salomon [Fri, 9 Sep 2011 00:35:17 +0000 (17:35 -0700)]
libertas: prioritize usb8388_olpc.bin firmware on OLPC machines
Normally, the v9 firmware will be loaded if it's available. However, on
OLPC XO-1 machines, the olpc-specific firmware supports extra functionality.
This makes the libertas driver attempt to load the custom firmware first
if the machine is an OLPC machine; if that fails (or it's not an OLPC
machine), fall back to attempting to load the other firmwares.
usb8388_olpc.bin is currently found in the linux-firmware repository.
Signed-off-by: Andres Salomon <dilinger@queued.net> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 Sep 2011 12:39:04 +0000 (14:39 +0200)]
rt2x00: Use the available helper functions to initialize the WCID table
Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the
WCID table instead of writing to the registers directly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 Sep 2011 12:38:36 +0000 (14:38 +0200)]
rt2x00: Forbid aggregation for STAs not programmed into the hw
If a STA is not known by the hw (i.e. has no WCID assigned) don't allow
aggregation since this might mess up tx status reports and we won't be
able to distinguish the reports of multiple WCID-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 Sep 2011 12:38:01 +0000 (14:38 +0200)]
rt2x00: Make use of sta_add/remove callbacks in rt2800
This allows us to assign a WCID to each STA even for STAs without
crypto key.
To achieve this search for an unused WCID in the HW WCID table and
assign it to the according STA. When configuring a pairwise key for this
STA we don't need to write the MAC address and BSSIDX anymore but just
update the crypto related fields in the WCID_ATTR table.
This has two advantages:
1) Setting a new key for an already available STA (PTK rekeying) is
slightly less expensive and should improve performance in situations
where a lot of rekeying happens (e.g. a huge number of stations and/or
a small rekeying interval)
2) The TXWI now gets a WCID assigned for unencrypted frames which will
be reflected in the corresponding tx status report. This should make tx
status reports in unencrypted AP mode more reliable as we can
distinguish between multiple key-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 8 Sep 2011 12:37:19 +0000 (14:37 +0200)]
rt2x00: Add WCID to HT TX descriptor
When sending an unencrypted frame to a STA the driver might want to pass
a suitable WCID since we don't have a key index to allow tx status
reports to get properly assigned to the correct STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log