Thomas Abraham [Fri, 3 Apr 2015 16:43:46 +0000 (18:43 +0200)]
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4210.
Changes by Bartlomiej:
- fixed issue with wrong dividers being setup by Common Clock Framework
(by an addition of CLK_RECALC_NEW_RATES clock flag to mout_apll clock,
without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board), this
was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE
and CLK_DIVIDER_READ_ONLY clock flags in the original patchset (in
"[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update
clock flags") but using these flags is not sufficient to fix the issue
observed
- removed Exynos5250 and Exynos5420 support for now
Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Mike Turquette <mturquette@linaro.org> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Thomas Abraham [Fri, 3 Apr 2015 16:43:45 +0000 (18:43 +0200)]
clk: samsung: add infrastructure to register cpu clocks
The CPU clock provider supplies the clock to the CPU clock domain. The
composition and organization of the CPU clock provider could vary among
Exynos SoCs. A CPU clock provider can be composed of clock mux, dividers
and gates. This patch defines a new clock type for CPU clock provider and
adds infrastructure to register the CPU clock providers for Samsung
platforms.
Changes by Bartlomiej:
- fixed issue with setting lower dividers before the parent clock speed
was lowered (the issue resulted in lockup on Exynos4210 SoC based
Origen board when "ondemand" cpufreq governor was stress tested)
- fixed missing spin_unlock on error in exynos_cpuclk_post_rate_change()
problem by moving cfg_data search outside of the spin locked area
- removed leftover kfree() in exynos_register_cpu_clock() that could
result in dereferencing the NULL pointer on error
- moved spin_lock earlier in exynos_cpuclk_pre_rate_change() to cover
reading of E4210_SRC_CPU and E4210_DIV_CPU1 registers
- added missing "last chance" checks to wait_until_divider_stable() and
wait_until_mux_stable() (needed in case that IRQ handling took long
time to proceed and resulted in function printing incorrect error
message about timeout)
- moved E4210_CPU_DIV[0,1]() macros just before their only users,
this resulted in moving them from patch #2 to patch #3/6 ("clk:
samsung: exynos4: add cpu clock configuration data and instantiate
cpu clock")
- removed E5250_CPU_DIV[0,1](), E5420_EGL_DIV0() and E5420_KFC_DIV()
macros for now
- added my Copyrights to drivers/clk/samsung/clk-cpu.c
Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Mike Turquette <mturquette@linaro.org> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Mike Turquette <mturquette@linaro.org> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Linus Torvalds [Sun, 7 Jun 2015 23:56:10 +0000 (16:56 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"Eight fixes across arch/mips. Nothing stands particuarly out nor is
complicated but fixes keep coming in at a higher than comfortable
rate"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: KVM: Do not sign extend on unsigned MMIO load
MIPS: BPF: Fix stack pointer allocation
MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
MIPS: Fix enabling of DEBUG_STACKOVERFLOW
MIPS: c-r4k: Fix typo in probe_scache()
MIPS: Avoid an FPE exception in FCSR mask probing
MIPS: ath79: Add a missing new line in log message
MIPS: ralink: Fix clearing the illegal access interrupt
Linus Torvalds [Sun, 7 Jun 2015 05:37:45 +0000 (22:37 -0700)]
Merge tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two fixes for the driver core that resolve some reported
issues.
One is a regression from 4.0, the other a fixes a reported oops that
has been there since 3.19.
Both have been in linux-next for a while with no problems"
* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: cacheinfo: handle absence of caches
drivers: of/base: move of_init to driver_init
Linus Torvalds [Sun, 7 Jun 2015 05:33:08 +0000 (22:33 -0700)]
Merge tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO driver fixes to resolve reported issues, some ozwpan
fixes for some reported CVE problems, and a rtl8712 driver fix for a
reported regression.
All have been in linux-next successfully"
* tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix stack dump
ozwpan: unchecked signed subtraction leads to DoS
ozwpan: divide-by-zero leading to panic
ozwpan: Use unsigned ints to prevent heap overflow
ozwpan: Use proper check to prevent heap overflow
iio: adc: twl6030-gpadc: Fix modalias
iio: adis16400: Fix burst transfer for adis16448
iio: adis16400: Fix burst mode
iio: adis16400: Compute the scan mask from channel indices
iio: adis16400: Use != channel indices for the two voltage channels
iio: adis16400: Report pressure channel scale
Linus Torvalds [Sun, 7 Jun 2015 05:14:23 +0000 (22:14 -0700)]
Merge tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a few TTY and Serial driver fixes for reported regressions
and crashes.
All of these have been in linux-next with no reported problems"
* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: Fix auditing support for cannonical mode
serial: 8250_omap: provide complete custom startup & shutdown callbacks
n_tty: Fix calculation of size in canon_copy_from_read_buf
serial: imx: Fix DMA handling for IDLE condition aborts
serial/amba-pl011: Unconditionally poll for FIFO space before each TX char
Linus Torvalds [Sun, 7 Jun 2015 05:06:53 +0000 (22:06 -0700)]
Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
Linus Torvalds [Sun, 7 Jun 2015 04:43:29 +0000 (21:43 -0700)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree fix from Grant Likely:
"Stupid typo fix for v4.1. One of the IS_ENABLED() macro calls forgot
the CONFIG_ prefix. Only affects a tiny number of platforms, but
still..."
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/dynamic: Fix test for PPC_PSERIES
Linus Torvalds [Sat, 6 Jun 2015 16:15:14 +0000 (09:15 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915 has a bunch of fixes, and Russell found a bug in sysfs writing
handling that results in userspace getting stuck"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: fix writing to /sys/class/drm/*/status
drm/i915: Move WaBarrierPerformanceFixDisable:skl to skl code from chv code
drm/i915: Include G4X/VLV/CHV in self refresh status
drm/i915: Initialize HWS page address after GPU reset
drm/i915: Don't skip request retirement if the active list is empty
drm/i915/hsw: Fix workaround for server AUX channel clock divisor
Linus Torvalds [Sat, 6 Jun 2015 16:08:23 +0000 (09:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a couple touchpad drivers fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - do not reduce trackpoint speed by half
Input: elantech - add new icbody type
Input: elantech - fix detection of touchpads where the revision matches a known rate
Markos Chandras [Thu, 4 Jun 2015 10:56:13 +0000 (11:56 +0100)]
MIPS: BPF: Fix stack pointer allocation
Fix stack pointer offset which could potentially corrupt
argument registers in the previous frame. The calculated offset
reflects the size of all the registers we need to preserve so there
is no need for this erroneous subtraction.
[ralf@linux-mips.org: Fixed conflict due to only applying this fix part
of the entire series as part of 4.1 fixes.]
Huacai Chen [Thu, 4 Jun 2015 06:53:47 +0000 (14:53 +0800)]
MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
setup_per_cpu_areas() only setup __per_cpu_offset[] for each possible
cpu, but loongson_sysconf.nr_cpus can be greater than possible cpus
(due to reserved_cpus_mask). So in loongson3_ipi_interrupt(), percpu
access will touch the original varible in .data..percpu section which
has been freed. Without this patch, cpu-hotplug will cause memery
corruption.
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/10524/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 4 Jun 2015 12:25:27 +0000 (13:25 +0100)]
MIPS: Fix enabling of DEBUG_STACKOVERFLOW
Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
Chris Leech [Thu, 28 May 2015 19:51:51 +0000 (12:51 -0700)]
iscsi_ibft: filter null v4-mapped v6 addresses
I've had reports of UEFI platforms failing iSCSI boot in various
configurations, that ended up being caused by network initialization
scripts getting tripped up by unexpected null addresses (0.0.0.0) being
reported for gateways, dhcp servers, and dns servers.
The tianocore EDK2 iSCSI driver generates an iBFT table that always uses
IPv4-mapped IPv6 addresses for the NIC structure fields. This results
in values that are "not present or not specified" being reported as
::ffff:0.0.0.0 rather than all zeros as specified.
The iscsi_ibft module filters unspecified fields from the iBFT from
sysfs, preventing userspace from using invalid values and making it easy
to check for the presence of a value. This currently fails in regard to
these mapped null addresses.
In order to remain consistent with how the iBFT information is exposed,
we should accommodate the behavior of the tianocore iSCSI driver as it's
already in the wild in a large number of servers.
Tested under qemu using an OVMF build of tianocore EDK2.
Signed-off-by: Chris Leech <cleech@redhat.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The map_single() function is not defined as static, even though it
doesn't seem to be used anywhere else in the kernel. Make it static to
avoid namespace pollution since this is a rather generic symbol.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Russell King [Fri, 5 Jun 2015 22:27:30 +0000 (08:27 +1000)]
drm: fix writing to /sys/class/drm/*/status
Writing to a file is supposed to return the number of bytes written.
Returning zero unfortunately causes bash to constantly spin trying
to write to the sysfs file, to such an extent that even ^c and ^z
have no effect. The only way out of that is to kill the shell and
log back in. This isn't nice behaviour.
Fix it by returning the number of characters written to sysfs files.
[airlied: used suggestion from Al Viro] Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 5 Jun 2015 21:14:13 +0000 (07:14 +1000)]
Merge tag 'drm-intel-fixes-2015-06-05' of git://anongit.freedesktop.org/drm-intel into drm-fixes
bunch of i915 fixes.
* tag 'drm-intel-fixes-2015-06-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Move WaBarrierPerformanceFixDisable:skl to skl code from chv code
drm/i915: Include G4X/VLV/CHV in self refresh status
drm/i915: Initialize HWS page address after GPU reset
drm/i915: Don't skip request retirement if the active list is empty
drm/i915/hsw: Fix workaround for server AUX channel clock divisor
Linus Torvalds [Fri, 5 Jun 2015 17:22:06 +0000 (10:22 -0700)]
Merge tag 'pci-v4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Resource management
- Fix IOV sorting by alignment (Wei Yang)
- Preserve resource size during alignment reordering (Yinghai Lu)
Miscellaneous
- MAINTAINERS: Add Pratyush for SPEAr13xx and DesignWare PCIe (Pratyush Anand)"
* tag 'pci-v4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Preserve resource size during alignment reordering
PCI: Fix IOV resource sorting by alignment requirement
MAINTAINERS: Add Pratyush Anand as SPEAr13xx and DesignWare PCIe maintainer
Linus Torvalds [Fri, 5 Jun 2015 17:16:52 +0000 (10:16 -0700)]
Merge tag 'sound-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It was a fairly calm week; here you can find only a few trivial quirks
and fixes for USB and HD-audio. All changes are pretty device
specific"
* tag 'sound-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: fix missing input volume controls in MAYA44 USB(+)
ALSA: usb-audio: add MAYA44 USB+ mixer control names
ALSA: hda/realtek - Add a fixup for another Acer Aspire 9420
ALSA: hda - Fix jack detection at resume with VT codecs
ALSA: usb-audio: don't try to get Outlaw RR2150 sample rate
ALSA: usb-audio: Add mic volume fix quirk for Logitech Quickcam Fusion
ALSA: hda/realtek - Suooprt Dell headset mode for ALC256
Linus Torvalds [Fri, 5 Jun 2015 17:14:51 +0000 (10:14 -0700)]
Merge tag 'iommu-fixes-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fix from Joerg Roedel:
"Only one patch:
- Revert "iommu/amd: Don't allocate with __GFP_ZERO in
alloc_coherent".
This patch caused problems with some drivers, so it is better to
revert it now until the drivers have been fixed"
* tag 'iommu-fixes-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent"
Linus Torvalds [Fri, 5 Jun 2015 17:03:48 +0000 (10:03 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- early_idt_handlers[] fix that fixes the build with bleeding edge
tooling
- build warning fix on GCC 5.1
- vm86 fix plus self-test to make it harder to break it again"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/irq: Stop relying on magic JMP behavior for early_idt_handlers
x86/asm/entry/32, selftests: Add a selftest for kernel entries from VM86 mode
x86/boot: Add CONFIG_PARAVIRT_SPINLOCKS quirk to arch/x86/boot/compressed/misc.h
x86/asm/entry/32: Really make user_mode() work correctly for VM86 mode
Linus Torvalds [Fri, 5 Jun 2015 17:00:53 +0000 (10:00 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest chunk of the changes are two regression fixes: a HT
workaround fix and an event-group scheduling fix. It's been verified
with 5 days of fuzzer testing.
Linus Torvalds [Fri, 5 Jun 2015 16:58:36 +0000 (09:58 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just two small fixes: one radeon, one amdkfd"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdkfd: fix topology bug with capability attr.
drm/radeon: use proper ACR regisiter for DCE3.2
Linus Torvalds [Fri, 5 Jun 2015 16:54:43 +0000 (09:54 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bug fixes from Wolfram Sang:
"Two small bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: s3c2410: fix oops in suspend callback for non-dt platforms
i2c: hix5hd2: Fix modalias to make module auto-loading work
Hans de Goede [Fri, 5 Jun 2015 05:31:43 +0000 (22:31 -0700)]
Input: alps - do not reduce trackpoint speed by half
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"IS_ENABLED(PPC_PSERIES)" always evaluates to false, as IS_ENABLED() is
supposed to be used with the full Kconfig symbol name, including the
"CONFIG_" prefix.
Add the missing "CONFIG_" prefix to fix this.
Fixes: a25095d451ece23b ("of: Move dynamic node fixups out of powerpc and into common code") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org #+3.17 Signed-off-by: Grant Likely <grant.likely@linaro.org>
Helge Deller [Thu, 4 Jun 2015 21:57:18 +0000 (23:57 +0200)]
compat: cleanup coding in compat_get_bitmap() and compat_put_bitmap()
In the functions compat_get_bitmap() and compat_put_bitmap() the
variable nr_compat_longs stores how many compat_ulong_t words should be
copied in a loop.
The copy loop itself is this:
if (nr_compat_longs-- > 0) {
if (__get_user(um, umask)) return -EFAULT;
} else {
um = 0;
}
Since nr_compat_longs gets unconditionally decremented in each loop and
since it's type is unsigned this could theoretically lead to out of
bounds accesses to userspace if nr_compat_longs wraps around to
(unsigned)(-1).
Although the callers currently do not trigger out-of-bounds accesses, we
should better implement the loop in a safe way to completely avoid such
warp-arounds.
Linus Torvalds [Thu, 4 Jun 2015 17:19:34 +0000 (10:19 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We have two small fixes:
- pl330 termination hang fix by Krzysztof
- hsu memory leak fix by Peter"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: hsu: Fix memory leak when stopping a running transfer
dmaengine: pl330: Fix hang on dmaengine_terminate_all on certain boards
Commit 066450be41 ("perf/x86/intel/pt: Clean up the control flow
in pt_pmu_hw_init()") changed attribute initialization so that
only the first attribute gets initialized using
sysfs_attr_init(), which upsets lockdep.
This patch fixes the glitch so that all allocated attributes are
properly initialized thus fixing the lockdep warning reported by
Tvrtko and Imre.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Reported-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: <linux-kernel@vger.kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org>
drm/i915: Include G4X/VLV/CHV in self refresh status
Add all missing platforms handled by intel_set_memory_cxsr() to the
i915_sr_status debugfs entry.
v2: Add G4X too. (Ville)
Clarify the change also affects CHV. (Ander)
References: https://bugs.freedesktop.org/show_bug.cgi?id=89792 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Linus Torvalds [Wed, 3 Jun 2015 23:35:00 +0000 (16:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"Sending this off now, as I'm not aware of other current bugs, nor do I
expect further fixes before 4.1 final. This contains two fixes:
- a fix for a bdi unregister warning that gets spewed on md, due to a
regression introduced earlier in this cycle. From Neil Brown.
- a fix for a compile warning for NVMe on 32-bit platforms, also a
regression introduced in this cycle. From Arnd Bergmann"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: fix type warning on 32-bit
block: discard bdi_unregister() in favour of bdi_destroy()
Jan Kara [Wed, 3 Jun 2015 13:50:35 +0000 (15:50 +0200)]
lib: Clarify the return value of strnlen_user()
strnlen_user() can return a number in a range 0 to count +
sizeof(unsigned long) - 1. Clarify the comment at the top of the
function so that users don't think the function returns at most count+1.
Signed-off-by: Jan Kara <jack@suse.cz>
[ Also added commentary about preferably not using this function ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clemens Ladisch [Wed, 3 Jun 2015 09:36:51 +0000 (11:36 +0200)]
ALSA: usb-audio: fix missing input volume controls in MAYA44 USB(+)
The driver worked around an error in the MAYA44 USB(+)'s mixer unit
descriptor by aborting before parsing the missing field. However,
aborting parsing too early prevented parsing of the other units
connected to this unit, so the capture mixer controls would be missing.
Fix this by moving the check for this descriptor error after the parsing
of the unit's input pins.
Use the default FCSR value in mask probing, avoiding an FPE exception
where reset has left any exception enable and their corresponding cause
bits set and the register is then rewritten with these bits active.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Joshua Kinard <kumba@gentoo.org> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sasha Levin [Wed, 28 Jan 2015 20:30:43 +0000 (15:30 -0500)]
vfs: read file_handle only once in handle_to_path
We used to read file_handle twice. Once to get the amount of extra
bytes, and once to fetch the entire structure.
This may be problematic since we do size verifications only after the
first read, so if the number of extra bytes changes in userspace between
the first and second calls, we'll have an incoherent view of
file_handle.
Instead, read the constant size once, and copy that over to the final
structure without having to re-read it again.
Jan Kara [Tue, 2 Jun 2015 15:10:28 +0000 (17:10 +0200)]
lib: Fix strnlen_user() to not touch memory after specified maximum
If the specified maximum length of the string is a multiple of unsigned
long, we would load one long behind the specified maximum. If that
happens to be in a next page, we can hit a page fault although we were
not expected to.
Fix the off-by-one bug in the test whether we are at the end of the
specified range.
Signed-off-by: Jan Kara <jack@suse.cz> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Mon, 1 Jun 2015 06:23:53 +0000 (15:53 +0930)]
ia64: make cpu_callin_map non-volatile.
cpumask_test_cpu() doesn't take volatile, unlike the obsoleted
cpu_isset. The only place ia64 really cares is the spin waiting for a
bit; udelay() is probably a barrier but insert barrier() to be sure.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Tony Luck <tony.luck@intel.com>
Peter Ujfalusi [Tue, 26 May 2015 10:11:28 +0000 (13:11 +0300)]
dmaengine: hsu: Fix memory leak when stopping a running transfer
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[andy: fix the typo to prevent a compilation error] Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Lutomirski [Fri, 22 May 2015 23:15:47 +0000 (16:15 -0700)]
x86/asm/irq: Stop relying on magic JMP behavior for early_idt_handlers
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
The DMA-API does not strictly require that the memory
returned by dma_alloc_coherent is zeroed out. For that
another function (dma_zalloc_coherent) should be used. But
all other x86 DMA-API implementation I checked zero out the
memory, so that some drivers rely on it and break when it is
not.
It seems the (driver-)world is not yet ready for this
change, so revert it.
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
1) Setup the core/threads/sockets bitmaps correctly so that 'lscpus'
and friends operate properly. Frtom Chris Hyser.
2) The bit that normally means "Cached Virtually" on sun4v systems,
actually changes meaning in M7 and later chips. Fix from Khalid
Aziz.
3) One some PCI-E systems we need to probe different OF properties to
fill in the PCI slot information properly, from Eric Snowberg.
4) Kill an extraneous memset after kzalloc(), from Christophe Jaillet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
sparc64: pci slots information is not populated in sysfs
sparc: kernel: GRPCI2: Remove a useless memset
sparc64: Setup sysfs to mark LDOM sockets, cores and threads correctly
The following patch reverts the ebtables chunk that enforces counters that was
introduced in the recently applied d26e2c9ffa38 ('Revert "netfilter: ensure
number of counters is >0 in do_replace()"') since this breaks ebtables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Fri, 29 May 2015 18:28:26 +0000 (11:28 -0700)]
vti6: Add pmtu handling to vti6_xmit.
We currently rely on the PMTU discovery of xfrm.
However if a packet is localy sent, the PMTU mechanism
of xfrm tries to to local socket notification what
might not work for applications like ping that don't
check for this. So add pmtu handling to vti6_xmit to
report MTU changes immediately.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yinghai Lu [Fri, 29 May 2015 05:40:00 +0000 (22:40 -0700)]
PCI: Preserve resource size during alignment reordering
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.
In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus. Even if we'd had the correct size, the end would
have been off by one.
Preserve the resource size when we adjust its alignment.
[bhelgaas: changelog] Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com> CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It isn't right, ethtool is meant to manage one PHY instance
per netdevice at a time, and this is selected by the SET
command. Therefore by definition the GET command must only
return the settings for the configured and selected PHY.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 1 Jun 2015 12:08:18 +0000 (15:08 +0300)]
bnx2x: Move statistics implementation into semaphores
Commit dff173de84958 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Mon, 1 Jun 2015 10:30:24 +0000 (11:30 +0100)]
xen: netback: read hotplug script once at start of day.
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Mon, 1 Jun 2015 10:30:04 +0000 (11:30 +0100)]
xen: netback: fix printf format string warning
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_build_gops’:
drivers/net/xen-netback/netback.c:1253:8: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘int’ [-Wformat=]
(txreq.offset&~PAGE_MASK) + txreq.size);
^
PAGE_MASK's type can vary by arch, so a cast is needed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
----
v2: Cast to unsigned long, since PAGE_MASK can vary by arch. Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernhard Thaler [Thu, 28 May 2015 08:26:18 +0000 (10:26 +0200)]
Revert "netfilter: ensure number of counters is >0 in do_replace()"
This partially reverts commit 1086bbe97a07 ("netfilter: ensure number of
counters is >0 in do_replace()") in net/bridge/netfilter/ebtables.c.
Setting rules with ebtables does not work any more with 1086bbe97a07 place.
There is an error message and no rules set in the end.
e.g.
~# ebtables -t nat -A POSTROUTING --src 12:34:56:78:9a:bc -j DROP
Unable to update the kernel. Two possible causes:
1. Multiple ebtables programs were executing simultaneously. The ebtables
userspace tool doesn't by default support multiple ebtables programs
running
Reverting the ebtables part of 1086bbe97a07 makes this work again.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jonas Gorski [Mon, 25 May 2015 17:53:54 +0000 (19:53 +0200)]
MIPS: ralink: Fix clearing the illegal access interrupt
Due to a typo the illegal access interrupt is never cleared in by
the interupt handler, causing an effective deadlock on the first
illegal access.
This was broken since the code was introduced in 5433acd81e87 ("MIPS:
ralink: add illegal access driver"), but only exposed when the Kconfig
symbol was added, thus enabling the code.
Cc: <stable@vger.kernel.org> [3.18+] Fixes: a7b7aad383c ("MIPS: ralink: add missing symbol for RALINK_ILL_ACC") Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10172/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ville Syrjälä [Thu, 28 May 2015 15:32:36 +0000 (18:32 +0300)]
drm/i915: Don't skip request retirement if the active list is empty
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jim Bride [Wed, 27 May 2015 17:21:48 +0000 (10:21 -0700)]
drm/i915/hsw: Fix workaround for server AUX channel clock divisor
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: stable@vger.kernel.org Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Khalid Aziz [Wed, 27 May 2015 16:00:46 +0000 (10:00 -0600)]
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
Bit 9 of TTE is CV (Cacheable in V-cache) on sparc v9 processor while
the same bit 9 is MCDE (Memory Corruption Detection Enable) on M7
processor. This creates a conflicting usage of the same bit. Kernel
sets TTE.cv bit on all pages for sun4v architecture which works well
for sparc v9 but enables memory corruption detection on M7 processor
which is not the intent. This patch adds code to determine if kernel
is running on M7 processor and takes steps to not enable memory
corruption detection in TTE erroneously.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Snowberg [Wed, 27 May 2015 15:59:19 +0000 (11:59 -0400)]
sparc64: pci slots information is not populated in sysfs
Add PCI slot numbers within sysfs for PCIe hardware. Larger
PCIe systems with nested PCI bridges and slots further
down on these bridges were not being populated within sysfs.
This will add ACPI style PCI slot numbers for these systems
since the OF 'slot-names' information is not available on
all PCIe platforms.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com> Reviewed-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 29 May 2015 17:29:46 +0000 (10:29 -0700)]
net: dsa: Properly propagate errors from dsa_switch_setup_one
While shuffling some code around, dsa_switch_setup_one() was introduced,
and it was modified to return either an error code using ERR_PTR() or a
NULL pointer when running out of memory or failing to setup a switch.
This is a problem for its caler: dsa_switch_setup() which uses IS_ERR()
and expects to find an error code, not a NULL pointer, so we still try
to proceed with dsa_switch_setup() and operate on invalid memory
addresses. This can be easily reproduced by having e.g: the bcm_sf2
driver built-in, but having no such switch, such that drv->setup will
fail.
Fix this by using PTR_ERR() consistently which is both more informative
and avoids for the caller to use IS_ERR_OR_NULL().
Fixes: df197195a5248 ("net: dsa: split dsa_switch_setup into two functions") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Fri, 29 May 2015 17:47:07 +0000 (13:47 -0400)]
tcp: fix child sockets to use system default congestion control if not set
Linux 3.17 and earlier are explicitly engineered so that if the app
doesn't specifically request a CC module on a listener before the SYN
arrives, then the child gets the system default CC when the connection
is established. See tcp_init_congestion_control() in 3.17 or earlier,
which says "if no choice made yet assign the current value set as
default". The change ("net: tcp: assign tcp cong_ops when tcp sk is
created") altered these semantics, so that children got their parent
listener's congestion control even if the system default had changed
after the listener was created.
This commit returns to those original semantics from 3.17 and earlier,
since they are the original semantics from 2007 in 4d4d3d1e8 ("[TCP]:
Congestion control initialization."), and some Linux congestion
control workflows depend on that.
In summary, if a listener socket specifically sets TCP_CONGESTION to
"x", or the route locks the CC module to "x", then the child gets
"x". Otherwise the child gets current system default from
net.ipv4.tcp_congestion_control. That's the behavior in 3.17 and
earlier, and this commit restores that.
Fixes: 55d8694fa82c ("net: tcp: assign tcp cong_ops when tcp sk is created") Cc: Florian Westphal <fw@strlen.de> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Glenn Judd <glenn.judd@morganstanley.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 30 May 2015 16:16:53 +0000 (09:16 -0700)]
udp: fix behavior of wrong checksums
We have two problems in UDP stack related to bogus checksums :
1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()
2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.
This patch is an attempt to make things better.
We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sudeep Holla [Wed, 27 May 2015 10:26:13 +0000 (11:26 +0100)]
drivers/base: cacheinfo: handle absence of caches
On some simulators like GEM5, caches may not be simulated. In those
cases, the cache levels and leaves will be zero and will result in
following exception:
kcalloc(0) returns a special value ZERO_SIZE_PTR which is non-NULL value
but results in fault only on any attempt to dereferencing it. So
checking for the non-NULL pointer will not suffice.
This patch checks for non-zero cache leaf nodes and returns error if
there are no cache leaves in detect_cache_attributes.
Cc: <stable@vger.kernel.org> # 3.19.x Cc: Will Deacon <will.deacon@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: William Wang <william.wang@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Pieczko [Fri, 29 May 2015 11:25:54 +0000 (12:25 +0100)]
sfc: free multiple Rx buffers when required
When Rx packet data must be dropped, all the buffers
associated with that Rx packet must be freed. Extend
and rename efx_free_rx_buffer() to efx_free_rx_buffers()
and loop through all the fragments.
By doing so this patch fixes a possible memory leak.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 31 May 2015 23:00:34 +0000 (16:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fix from Al Viro:
"Off-by-one in d_walk()/__dentry_kill() race fix.
It's very hard to hit; possible in the same conditions as the original
bug, except that you need the skipped branch to contain all the
remaining evictables, so that the d_walk()-calling loop in
d_invalidate() decides there's nothing more to do and doesn't go for
another pass - otherwise that next pass will sweep the sucker.
So it's not too urgent, but seeing that the fix is obvious and the
original commit has spread into all -stable branches..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
d_walk() might skip too much
Laura Abbott [Thu, 14 May 2015 18:42:17 +0000 (11:42 -0700)]
n_tty: Fix auditing support for cannonical mode
Commit 32f13521ca68bc624ff6effc77f308a52b038bf0
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.
Fixes: 32f13521ca68 ("n_tty: Line copy to user buffer in canonical mode") Reported-by: Miloslav Trmač <mitr@redhat.com> Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250_omap: provide complete custom startup & shutdown callbacks
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d11859 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb9 ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb93 ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"") Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 31 May 2015 19:03:42 +0000 (12:03 -0700)]
Merge branch 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 4.1 all across the tree"
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux:
MIPS: strnlen_user.S: Fix a CPU_DADDI_WORKAROUNDS regression
MIPS: BMIPS: Fix bmips_wr_vec()
MIPS: ath79: fix build problem if CONFIG_BLK_DEV_INITRD is not set
MIPS: Fuloong 2E: Replace CONFIG_USB_ISP1760_HCD by CONFIG_USB_ISP1760
MIPS: irq: Use DECLARE_BITMAP
ttyFDC: Fix to use native endian MMIO reads
MIPS: Fix CDMM to use native endian MMIO reads
Linus Torvalds [Sun, 31 May 2015 18:39:25 +0000 (11:39 -0700)]
Merge branch 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat tool fixes from Len Brown:
"Just one minor kernel dependency in this batch -- added a #define to
msr-index.h"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number to 4.7
tools/power turbostat: allow running without cpu0
tools/power turbostat: correctly decode of ENERGY_PERFORMANCE_BIAS
tools/power turbostat: enable turbostat to support Knights Landing (KNL)
tools/power turbostat: correctly display more than 2 threads/core
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
Linus Torvalds [Sun, 31 May 2015 18:24:49 +0000 (11:24 -0700)]
Merge tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Some late hwmon patches, all headed for -stable
- fix sysfs attribute initialization in nct6775 and nct6683 drivers
- do not attempt to auto-detect tmp435 on I2C address 0x37
- ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver"
* tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6683) Add missing sysfs attribute initialization
hwmon: (nct6775) Add missing sysfs attribute initialization
hwmon: (tmp401) Do not auto-detect chip on I2C address 0x37
hwmon: (ntc_thermistor) Ensure iio channel is of type IIO_VOLTAGE
Takashi Iwai [Sun, 31 May 2015 07:27:29 +0000 (09:27 +0200)]
ALSA: hda - Fix jack detection at resume with VT codecs
VT202x codecs seem requiring some delay after the resume D0 power
transition for making the jack detection working again. Without the
delay soon after D0, the jack is always detected as unplugged.
Ivan Vecera [Thu, 28 May 2015 21:10:08 +0000 (23:10 +0200)]
bna: fix soft lock-up during firmware initialization failure
Bug in the driver initialization causes soft-lockup if firmware
initialization timeout is reached. Polling function bfa_ioc_poll_fwinit()
incorrectly calls bfa_nw_iocpf_timeout() when the timeout is reached.
The problem is that bfa_nw_iocpf_timeout() calls again
bfa_ioc_poll_fwinit()... etc. The bfa_ioc_poll_fwinit() should directly
send timeout event for iocpf and the same should be done if firmware
download into HW fails.
Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 28 May 2015 21:10:07 +0000 (23:10 +0200)]
bna: remove unreasonable iocpf timer start
Driver starts iocpf timer prior bnad_ioceth_enable() call and this is
unreasonable. This piece of code probably originates from Brocade/Qlogic
out-of-box driver during initial import into upstream. This driver uses
only one timer and queue to implement multiple timers and this timer is
started at this place. The upstream driver uses multiple timers instead
of this.
Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 28 May 2015 21:10:06 +0000 (23:10 +0200)]
bna: fix firmware loading on big-endian machines
Firmware required by bna is stored in appropriate files as sequence
of LE32 integers. After loading by request_firmware() they need to be
byte-swapped on big-endian arches. Without this conversion the NIC
is unusable on big-endian machines.
Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 31 May 2015 06:37:46 +0000 (23:37 -0700)]
Merge tag 'mac80211-for-davem-2015-05-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This just has a single docbook build fix. In my confusion
I'd already sent the same fix for -next, but Ben Hutchings
noted it's necessary in 4.1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log