Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Soeren Moch [Sun, 7 Feb 2016 18:34:30 +0000 (19:34 +0100)]
ARM: dts: imx6q-tbs2910: add SATA PHY configuration
Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
ARM: dts: imx6dlq-wandboard-revb1.dts: use unique model id
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 8536239e371f ("ARM: dts: Restructure imx6qdl-wandboard.dtsi for new
rev C1 board.")' created new files imx6dl-wandboard-revb1.dts and
imx6q-wandboard-revb1.dts but used the same model identifier as in
imx6dl-wandboard.dts and imx6q-wandboard.dts.
This patch provides unique model identifiers for revision B1 of
the Wandboard Dual and Wandbaord Quad.
The patch leaves imx6dl-wandboard.dts and imx6q-wandboard.dts unchanged
because it is not foreseeable if the same dts will valid for future
board revisions or not. Furthermore we should avoid unnecessary
changes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bai Ping [Tue, 2 Feb 2016 10:01:35 +0000 (18:01 +0800)]
ARM: dts: imx: Add basic dts support for imx6qp SOC
The i.MX6Quad Plus processor is an high performance SOC of i.MX6 family.
It has enhanced graphics performance and increased overall memory bandwidth
compared to i.MX6Q. Most of the design are same as i.MX6Quad/Dual, so code
for i.MX6Quad can be resued by this chip. The revision number is identied as
i.MX6Q Rev2.0, but actually it is a new chip, as we did many change to the
overall architecture.
This patch adds basic dtsi file support for the new i.MX6Quad Plus processor.
Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 7 Dec 2015 21:51:16 +0000 (13:51 -0800)]
ARM: dts: vf610-twr: relicense vf610-twr.dts under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf610-twr.dts file to this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf610-twr.dts
--CC: Chao Fu <B44548@freescale.com> CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
--CC: Fugang Duan <B38611@freescale.com>
--CC: Jingchang Lu <b35083@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Acked-by: Bill Pringlemeir <bpringle@sympatico.ca> Acked-by: Cory Tusar <cory.tusar@pid1solutions.com> Acked-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 7 Dec 2015 21:51:13 +0000 (13:51 -0800)]
ARM: dts: vf610: relicense vf???.dtsi under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vfxxx.dtsi, vf500.dtsi and vf610.dtsi files to
this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf???.dtsi
--CC: Chao Fu <B44548@freescale.com> CC: Cosmin Stoica <cosminstefan.stoica@freescale.com> CC: Frank Li <Frank.Li@freescale.com> CC: Fugang Duan <B38611@freescale.com>
--CC: Huang Shijie <b32955@freescale.com>
--CC: Jingchang Lu <jingchang.lu@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Acked-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Cory Tusar <cory.tusar@pid1solutions.com> Acked-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCIe reset signals are active low, and our GPIO for this is directly
connected to the PCIe reset. However, as the PCIe driver was not using
the flag, the specification of '0' flags (which means active high) had
not been noticed. Correct this oversight, and switch to using the
GPIO flag definitions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lothar Waßmann [Wed, 20 Jan 2016 13:09:22 +0000 (14:09 +0100)]
ARM: dts: imx53-tx53: set correct mclk frequency
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Lothar Waßmann [Wed, 20 Jan 2016 12:57:03 +0000 (13:57 +0100)]
ARM: dts: imx6qdl-tx6: add ENET_OUT clock to fec node
ENET_OUT is used as reference clock for the ethernet PHY on the Ka-Ro
TX6 modules. Specify this clock in DTB to let it be managed correctly
by the driver.
Lothar Waßmann [Wed, 20 Jan 2016 12:57:02 +0000 (13:57 +0100)]
ARM: dts: imx6: use correct mclk frequency for audio codec
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Lothar Waßmann [Wed, 20 Jan 2016 12:30:15 +0000 (13:30 +0100)]
ARM: dts: imx28-tx28: use correct mclk frequency
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Tim Harvey [Thu, 7 Jan 2016 17:58:09 +0000 (09:58 -0800)]
ARM: dts: imx: ventana: add alternate PWM4 pinmux for GW54xx
The GW54xx can provide PWM4 out either the off-board backlight connector
or the off-board digital I/O connector. By default the pinmux routes it
to the backlight connector but this pinctl alternate provides documentation
for those who may want to change it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sudeep Holla [Wed, 21 Oct 2015 10:10:08 +0000 (11:10 +0100)]
ARM: dts: imx: replace legacy wakeup property with 'wakeup-source'
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Stefan Agner [Sun, 18 Oct 2015 04:05:22 +0000 (21:05 -0700)]
ARM: dts: vf610: add remaining SAI instaces
This adds the remaining SAI instances SAI0, SAI1 and SAI3. All
instances are very similar, except that the DMA channel of SAI3
is available on MUX1 (compared to MUX0 for SAI0-SAI2). Also,
SAI3 has a slightly different memory map due to a deeper FIFO,
however in practice the current driver works for SAI3 fine.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bai Ping [Tue, 2 Feb 2016 10:01:34 +0000 (18:01 +0800)]
clk: imx: Add clock support for imx6qp
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 24 Jan 2016 20:50:56 +0000 (12:50 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
Linus Torvalds [Sun, 24 Jan 2016 20:45:35 +0000 (12:45 -0800)]
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Emergency travel prevented me from completing my final testing on this
until today. Nothing here that couldn't wait until RC1 fixes, but I
thought it best to get it out sooner rather than later as it does
contain a build warning fix.
Summary:
A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:
ideapad-laptop:
- Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS:
- Combine multiple telemetry entries
intel_telemetry_debugfs:
- Fix unused warnings in telemetry debugfs"
* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS: Combine multiple telemetry entries
intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
Linus Torvalds [Sun, 24 Jan 2016 20:43:06 +0000 (12:43 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
Linus Torvalds [Sun, 24 Jan 2016 20:39:09 +0000 (12:39 -0800)]
Merge tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p updates from Eric Van Hensbergen:
"Sorry for the last minute pull request, there's was a change that
didn't get pulled into for-next until two weeks ago and I wanted to
give it some bake time.
Summary:
Rework and error handling fixes, primarily in the fscatch and fd
transports"
* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: use fscache mutex rather than spinlock
9p: trans_fd, bail out if recv fcall if missing
9p: trans_fd, read rework to use p9_parse_header
net/9p: Add device name details on error
Linus Torvalds [Sun, 24 Jan 2016 20:34:13 +0000 (12:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
Linus Torvalds [Sun, 24 Jan 2016 20:31:12 +0000 (12:31 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull SMB3 fixes from Steve French:
"A collection of CIFS/SMB3 fixes.
It includes a couple bug fixes, a few for improved debugging of
cifs.ko and some improvements to the way cifs does key generation.
I do have some additional bug fixes I expect in the next week or two
(to address a problem found by xfstest, and some fixes for SMB3.11
dialect, and a couple patches that just came in yesterday that I am
reviewing)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
cifs: fix race between call_async() and reconnect()
Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
cifs: Allow using O_DIRECT with cache=loose
cifs: Make echo interval tunable
cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
Print IP address of unresponsive server
cifs: Ratelimit kernel log messages
Josh Boyer [Sun, 24 Jan 2016 15:46:42 +0000 (10:46 -0500)]
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
If we detect that there is nothing to do just set the flag and do not
check if it was already set before. Races really do not matter. If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.
Since commit 0eb77e988032 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd. This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up. The VM_BUG_ON is therefore misleading and no more
appropriate. Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly. Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alban Bedel [Thu, 10 Dec 2015 09:57:20 +0000 (10:57 +0100)]
MIPS: zboot: Avoid useless rebuilds
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr> Cc: linux-mips@linux-mips.org Cc: Alex Smith <alex.smith@imgtec.com> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:47:55 +0000 (22:47 +0000)]
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.
Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:45:30 +0000 (22:45 +0000)]
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.
Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Sun, 24 Jan 2016 02:45:06 +0000 (18:45 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
James Hogan [Wed, 16 Dec 2015 23:49:38 +0000 (23:49 +0000)]
MIPS: Move KVM specific opcodes into asm/inst.h
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b943
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
James Hogan [Wed, 16 Dec 2015 23:49:37 +0000 (23:49 +0000)]
MIPS: KVM: Use cacheops.h definitions
Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
James Hogan [Wed, 16 Dec 2015 23:49:36 +0000 (23:49 +0000)]
MIPS: Break down cacheops.h definitions
Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.
To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
James Hogan [Wed, 16 Dec 2015 23:49:34 +0000 (23:49 +0000)]
MIPS: Update trap codes
Add a few missing trap codes.
[ralf@linux-mips.org: Drop removal of exception codes. I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
James Hogan [Wed, 16 Dec 2015 23:49:33 +0000 (23:49 +0000)]
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
James Hogan [Wed, 16 Dec 2015 23:49:31 +0000 (23:49 +0000)]
MIPS: KVM: Refactor added offsetof()s
When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.
Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
James Hogan [Wed, 16 Dec 2015 23:49:28 +0000 (23:49 +0000)]
MIPS: Move definition of DC bit to mipsregs.h
The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.
Lets reunite the DC bit definitions with its friends in mipsregs.h.
James Hogan [Wed, 16 Dec 2015 23:49:27 +0000 (23:49 +0000)]
MIPS: KVM: Drop some unused definitions from kvm_host.h
Some definitions in the MIPS asm/kvm_host.h are completely unused, so
lets drop them.
MS_TO_NS is no longer used since commit e30492bbe95a ("MIPS: KVM:
Rewrite count/compare timer emulation"). The others don't appear ever to
have been used.
Joshua Henderson [Thu, 14 Jan 2016 01:15:39 +0000 (18:15 -0700)]
MIPS: Add support for PIC32MZDA platform
This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.
This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Cristian Birsan [Thu, 14 Jan 2016 01:15:35 +0000 (18:15 -0700)]
IRQCHIP: irq-pic32-evic: Add support for PIC32 interrupt controller
This adds support for the interrupt controller present on PIC32 class
devices. It handles all internal and external interrupts. This controller
exists outside of the CPU core and is the arbitrator of all interrupts
(including interrupts from the CPU itself) before they are presented to
the CPU.
The following features are supported:
- DT properties for EVIC and for devices/peripherals that use interrupt lines
- Persistent and non-persistent interrupt handling
- irqdomain and generic chip support
- Configuration of external interrupt edge polarity
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12092/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Tue, 22 Dec 2015 13:56:39 +0000 (13:56 +0000)]
MIPS: ptrace: Drop cp0_tcstatus from regoffset_table[]
The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c5ad3 ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Linus Walleij [Tue, 22 Dec 2015 14:41:44 +0000 (15:41 +0100)]
MIPS: TXx9: iocled: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:41:19 +0000 (15:41 +0100)]
MIPS: RB532: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:41:01 +0000 (15:41 +0100)]
MIPS: TXx9: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:40:27 +0000 (15:40 +0100)]
MIPS: ar7: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:40:02 +0000 (15:40 +0100)]
MIPS: Alchemy: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Matt Redfearn [Fri, 18 Dec 2015 12:47:00 +0000 (12:47 +0000)]
MIPS: smp-cps: Ensure secondary cores start with EVA disabled
The kernel currently assumes that a core will start up in legacy mode
using the exception base provided through the CM GCR registers. If a
core has been configured in hardware to start in EVA mode, these
assumptions will fail.
This patch ensures that secondary cores are initialized to meet these
assumptions.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11907/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the description of the microMIPS NOP16 encoding or MM_NOP16, which
is not equivalent to the MIPS16 NOP instruction. This is 0x0c00 and
represents the microMIPS `MOVE16 $0, $0' operation, whereas MIPS16 NOP
is encoded as 0x6500, representing `MOVE $0, $16'.
Also fix a typo in `mm_fp0_format' description.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12177/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: math-emu: dsemul: Correct description of the emulation frame
Remove irrelevant content from the description of the emulation frame in
`mips_dsemul', referring to bare-metal configurations. Update the text,
reflecting the change made with commit ba3049ed4086 ("MIPS: Switch FPU
emulator trap to BREAK instruction."), where we switched from using an
address error exception on an unaligned access to the use of a BREAK 514
instruction causing a breakpoint exception instead.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12176/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: math-emu: Correct the emulation of microMIPS ADDIUPC instruction
Emulate the microMIPS ADDIUPC instruction directly in `mips_dsemul'. If
executed in the emulation frame, this instruction produces an incorrect
result, because the value of the PC there is not the same as where the
instruction originated.
Reshape code so as to handle all microMIPS cases together.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12175/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: math-emu: Make microMIPS branch delay slot emulation work
Complement commit 102cedc32a6e ("MIPS: microMIPS: Floating point
support.") which introduced microMIPS FPU emulation, but did not adjust
the encoding of the BREAK instruction used to terminate the branch delay
slot emulation frame. Consequently the execution of any such frame is
indeterminate and, depending on CPU configuration, will result in random
code execution or an offending program being terminated with SIGILL.
This is because the regular MIPS BREAK instruction is encoded with the 0
major and the 0xd minor opcode, however in the microMIPS instruction set
this major/minor opcode pair denotes an encoding reserved for the DSP
ASE. Instead the microMIPS BREAK instruction is encoded with the 0
major and the 0x7 minor opcode.
Use the correct BREAK encoding for microMIPS FPU emulation then.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12174/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: math-emu: dsemul: Fix ill formatting of microMIPS part
Correct formatting breakage introduced with commit 102cedc32a6e ("MIPS:
microMIPS: Floating point support."), so that further changes to this
code can be consistent.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12173/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
projects / linux-beck.git / log