Arnd Bergmann [Fri, 28 Nov 2014 14:01:57 +0000 (15:01 +0100)]
Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Arnd Bergmann [Fri, 28 Nov 2014 11:36:43 +0000 (12:36 +0100)]
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "temporarily disable rk3288-smp" from Heiko Stuebner:
Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.
* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: temporarily disable smp on rk3288
Pankaj Dubey [Wed, 26 Nov 2014 18:24:45 +0000 (03:24 +0900)]
ARM: dts: add sysreg phandle to i2c device nodes for exynos
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Russell King <linux@arm.linux.org.uk> CC: devicetree@vger.kernel.org CC: linux-doc@vger.kernel.org Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Youngjun Cho [Wed, 26 Nov 2014 17:43:39 +0000 (02:43 +0900)]
ARM: dts: add board dts file for Exynos3250-based Monk board
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Roger Quadros [Wed, 29 Oct 2014 15:52:57 +0000 (17:52 +0200)]
ARM: dts: am335x-evm: Add DCAN1 details
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 9 Sep 2014 13:15:35 +0000 (16:15 +0300)]
ARM: dts: am33xx: Update DCAN nodes
Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Fri, 18 Jul 2014 05:59:11 +0000 (11:29 +0530)]
ARM: dts: am437x-gp: Add dcan support
Add DCAN support for AM437x GP EVM with both DCAN instances.
[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Robin Gong [Wed, 12 Nov 2014 08:20:37 +0000 (16:20 +0800)]
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
All chips of i.mx6 can be powered off by programming SNVS.
For example :
On i.mx6q-sabresd board, PMIC_ON_REQ connect with external
pmic ON/OFF pin, that will cause the whole PMIC powered off
except VSNVS. And system can restart once PMIC_ON_REQ goes
high by push POWRER key.
Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Philipp Zabel [Tue, 11 Nov 2014 21:12:47 +0000 (19:12 -0200)]
ARM: dts: imx6qdl: Enable CODA960 VPU
This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
imx6q-tbs2910 board uses sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Stefan Agner [Tue, 4 Nov 2014 13:07:09 +0000 (14:07 +0100)]
ARM: dts: vf610: enable USB misc/phy nodes where necessary
Since restructuring of the device tree files, the USB misc/phy
nodes are disabled by default. Hence we need to enable those
explicitly when USB is used.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stefan Agner [Tue, 4 Nov 2014 13:07:08 +0000 (14:07 +0100)]
ARM: dts: vf610: use new GPIO support
Use GPIO support by adding SD card detection configuration and
GPIO pinmux for Colibri's standard GPIO pins. Attach the GPIO
pins to the iomuxc node to get the GPIO pin settings applied.
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.
This patch fixes i2c2, i2c3 pin configuration which caused messages:
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Stefan Agner [Sun, 2 Nov 2014 20:36:47 +0000 (21:36 +0100)]
ARM: dts: vf500-colibri: add Colibri VF50 support
Add Colibri VF50 device tree files vf500-colibri.dtsi and
vf500-colibri-eval-v3.dts, in line with the Colibri VF61 device tree
files. However, to minimize dupplication we also add vf-colibri.dtsi
and vf-colibri-eval-v3.dtsi which contain the common device tree
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stefan Agner [Sun, 2 Nov 2014 20:36:46 +0000 (21:36 +0100)]
ARM: dts: vf610: create generic base device trees
This adds more generic base device trees for Vybrid SoCs. There
are three series of Vybrid SoC commonly available:
- VF3xx series: single core, Cortex-A5 without external memory
- VF5xx series: single core, Cortex-A5
- VF6xx series: dual core, Cortex-A5/Cortex-M4
The second digit represents the presents of a L2 cache (VFx1x).
The VF3xx series are not suitable for Linux especially since the
internal memory is quite small (1.5MiB).
The VF500 is essentially the base SoC, with only one core and
without L1 cache. The VF610 is a superset of the VF500, hence
vf500.dtsi is then included and enhanced by vf610.dtsi. There is
no board using VF510 or VF600 currently, but, if needed, they can
be added easily.
The Linux kernel can also run on the Cortex-M4 CPU of Vybrid
using !MMU support. This patchset creates a device tree structure
which allows to share peripherals nodes for a VF6xx Cortex-M4
device tree too. The two CPU types have different views of the
system: Foremost they are using different interrupt controllers,
but also the memory map is slightly different. The base device
tree vfxxx.dtsi allows to create SoC and board level device trees
supporting the Cortex-M4 while reusing the shared peripherals
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stefan Agner [Sun, 2 Nov 2014 20:36:44 +0000 (21:36 +0100)]
ARM: dts: vf610: assign oscillator to clock module
The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.
This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Jingchang Lu [Fri, 31 Oct 2014 09:01:10 +0000 (17:01 +0800)]
ARM: dts: Add initial LS1021A TWR board dts support
The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: Chao Fu <B44548@freescale.com> Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Jingchang Lu [Fri, 31 Oct 2014 09:01:09 +0000 (17:01 +0800)]
ARM: dts: Add initial LS1021A QDS board dts support
The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.
For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.
Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Chao Fu <B44548@freescale.com> Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Jingchang Lu [Fri, 31 Oct 2014 09:01:08 +0000 (17:01 +0800)]
ARM: dts: Add SoC level device tree support for LS1021A
This add Freescale QorIQ LS1021A SoC device tree support.
The QorIQ LS1021A processor incorporates dual ARM Cortex-A7 cores,
providing virtualization support, advanced security features and the
broadest array of high-speed interconnects and optimized peripheral
features.
The LS1021A SoC shares IPs with i.MX, Vybrid and PowerPC platform.
For the detail information about Freescale QorIQ LS1021A SoC,
please refer to the QorIQ LS1021A Reference Manual.
Bhuvanchandra DV [Mon, 22 Sep 2014 10:08:11 +0000 (15:38 +0530)]
ARM: dts: vf610-colibri: Add PWM support
The Colibri standard defines four pins as PWM outputs, two of them (PWM
A and C) are routed to FTM instance 0 and the other two (PWM B and D)
are routed to FTM instance 1. Hence enable both FTM instances for the
Colibri module and mux the four pins accordingly.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Wed, 24 Sep 2014 16:20:09 +0000 (18:20 +0200)]
ARM: dts: vf610: Add ARM Global Timer
Add Global Timer support which is part of the private peripherals
of the Cortex-A5 processor. This Global Timer is compatible with the
Cortex-A9 implementation. It's a 64-bit timer and is clocked by the
peripheral clock, which is typically 133 or 166MHz on Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 23 Nov 2014 07:07:02 +0000 (15:07 +0800)]
Merge tag 'imx-soc-3.19' into imx/dt
The i.MX SoC update for 3.19:
- Update i.MX6 suspend code to check DDR instead of CPU type, as the
difference we need to handle is between LPDDR2 and DDR3, not SoCs.
- Set anatop properly for LPDDR2 in DSM mode
- Add support for new SoC LS1021A which integrates dual Cortex-A7
- Add ENET initialization for i.MX6SX platform
- Add cpufreq support for i.MX53 platform
- Add a SNVS based poweroff driver for i.MX6 platforms
- Use ARM Global Timer as clocksource on VF610
Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.
Robin Gong [Wed, 12 Nov 2014 08:20:38 +0000 (16:20 +0800)]
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com> Acked-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Arnd Bergmann [Tue, 11 Nov 2014 16:03:25 +0000 (17:03 +0100)]
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
The newly introduced LS1021A SoC selects CONFIG_SOC_FSL, which
is originally symbol used for the PowerPC based platforms
and guards lots of code that does not build on ARM.
This breaks allmodconfig, so let's remove it for now, until
either all those drivers are fixed or they use a dependency
on IMX instead.
Stefan Agner [Sun, 2 Nov 2014 20:36:45 +0000 (21:36 +0100)]
ARM: imx: clk-vf610: get input clocks from assigned clocks
With the clock assignment device tree changes, the clocks get
initialized properly but the search for those clocks fails with
errors:
[ 0.000000] i.MX clk 4: register failed with -17
[ 0.000000] i.MX clk 5: register failed with -17
This is because the module can't find those clocks anymore, and
tries to initialize fixed clocks with the same name.
Get the clock modules input clocks from the assigned clocks by
default by using of_clk_get_by_name(). If this function returns
not a valid clock, fall back to the old behaviour and search the
input clock from the device tree's /clocks/$name node.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Lucas Stach [Fri, 26 Sep 2014 13:41:02 +0000 (15:41 +0200)]
ARM: imx53: clk: add ARM clock
The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Fri, 26 Sep 2014 13:41:01 +0000 (15:41 +0200)]
ARM: imx: add CPU clock type
This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.
While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add imx6sx iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
align with freescale internal tree related GPR macro define.
Stefan Agner [Wed, 24 Sep 2014 16:20:10 +0000 (18:20 +0200)]
ARM: vf610: Add ARM Global Timer clocksource option
Add the ARM Global Timer as clocksource/scheduler clock option and
use it as default scheduler clock. This leaves the PIT timer for
other users e.g. the secondary Cortex-M4 core. Also, the Global Timer
has double the precission (running at pheripheral clock compared to
IPG clock) and a 64-bit incrementing counter register. We still keep
the PIT timer as an secondary option in case the ARM Global Timer is
not available.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
ARM: imx: replace cpu type check with ddr type check
As the DDR/IO and MMDC setting are different on LPDDR2 and DDR3,
we used cpu type to decide how to do these settings in suspend
before which is NOT flexible, take i.MX6SL for example, although
it has LPDDR2 on EVK board, but users can also use DDR3 on other
boards, so it is better to read the DDR type from MMDC then decide
how to do related settings.
Shawn Guo [Sun, 23 Nov 2014 06:55:14 +0000 (14:55 +0800)]
Merge tag 'imx-fixes-3.18-2' into imx/soc
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit dc4805c2e78b (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
Heiko Stuebner [Sat, 22 Nov 2014 15:23:28 +0000 (16:23 +0100)]
ARM: dts: rockchip: temporarily disable smp on rk3288
Stock firmware on rk3288 does not initizalize the CNTVOFF registers
of the architected timer correctly. This introduces issues with the
newly added SMP support for rk3288, resulting in rcu stalls due to
differing timer values per core.
There exist preliminary and tested patches for u-boot for this problem,
but there are a minority of boards using other bootloaders like coreboot.
There also is currently a second solution for miss-initialized architected
timers in the works:
- clocksource: arch_timer: Fix code to use physical timers when requested
- clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
Therefore disable smp on rk3288 again till these are finalized, also
allowing coreboot-based boards to boot again.
Marek Szyprowski [Sat, 22 Nov 2014 14:44:11 +0000 (23:44 +0900)]
ARM: dts: add missing clock to MFC device for exynos4
sclk_mfc is required for MFC device since commit 0c2272170d78f826f6e97f99fb8a67fc17feef07 ("media: s5p-mfc: rename
special clock to sclk_mfc"), so add it to exynos4 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: Specify audio clock parents and rates for exynos4412-odroid-common
This ensures the core and the audio subsystem clocks are configured
properly, as expected by the sound machine driver. These bits are
missing to obtain proper audio sample rates in kernel v3.17, where
audio support for Odroid X2/U3 was first added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:13 +0000 (23:31 +0900)]
ARM: dts: Add trackpad to exynos5250-spring
The HP Chromebook 11 uses an Atmel maXTouch as trackpad.
The keymap was found by trial-and-error.
Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:07 +0000 (23:31 +0900)]
ARM: dts: Add temperature sensor to exynos5250-spring
Spotted in the Chrome OS 3.8 based device tree.
Needs CONFIG_SENSORS_LM90.
Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:03 +0000 (23:31 +0900)]
ARM: dts: Add usb3503 pinctrl to exynos5250-spring
Reported-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: Specify default clocks for Exynos4 camera devices
Specify the default mux and divider clocks in device tree
to ensure the FIMC devices on Trats, Trats2, Universal_c210
and Odroid X2/U3 boards are clocked from recommended clock
source and with maximum supported frequency.
For Trats2 also the MIPI-CSIS and the camera sensor clocks
are configured, the 'clock-frequency' property is deprecated
in favour of 'assigned-clock-rates' property.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adam YH Lee [Thu, 13 Nov 2014 18:04:33 +0000 (10:04 -0800)]
ARM: dts: Gumstix DuoVero: Bind vdac regulator to hdmi node
The HDMI node does not have a power supply attached. As a result its
power regulator, VDAC, shuts off on boot and screen loses signal.
This attaches VDAC (vdda_hdmi_dac) to HDMI's vdda-supply.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>