Andrew F. Davis [Fri, 16 Oct 2015 14:49:20 +0000 (09:49 -0500)]
power: bq27xxx_battery: Remove unneeded dependency in Kconfig
I2C is only required when using the config item BATTERY_BQ27XXX_I2C which
already depends on the I2C subsystem, remove the unneeded dependency from
BATTERY_BQ27XXX.
Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Document the settings exported by bq24257 charger driver through sysfs
entries:
- ovp_voltage
- in_dpm_voltage
- high_impedance_enable
- sysoff_enable
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Allow input current limit sysfs access
This patch allows reading and writing of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected (if the D+/D- USB signal-
based charger type detection is enabled) and to re-configure the maximum
current drawn from the external supply at runtime based on system-level
knowledge or user input. Note that upon charger disconnection and
re-connection the limit configured through firmware becomes active again
(or the D+/D- USB signal-based charger detection will be run again).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Add input DPM voltage threshold setting support
A new optional device property called "ti,in-dpm-voltage" is introduced
to allow configuring the input voltage threshold for the devices'
dynamic power path management (DPM) feature. In short, it can be used to
prevent the input voltage from dropping below a certain value as current
is drawn to charge the battery or supply the system.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Add SW-based approach for Power Good determination
A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Allow manual setting of input current limit
A new optional device property called "ti,current-limit" is introduced
to allow disabling the D+/D- USB signal-based charger type auto-
detection algorithm used to set the input current limit and instead to
use a fixed input current limit.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Add basic support for bq24250/bq24251
This patch adds basic support for bq24250 and bq24251 which are very
similar to the bq24257 the driver was originally written for. Basic
support means the ability to select a device through Kconfig, DT and
ACPI, an instance variable allowing to check which chip is active, and
the reporting back of the selected device through the model_name power
supply sysfs property.
This patch by itself is not sufficient to actually use those two added
devices in a real-world setting due to some feature differences which
are addressed by other patches in this series.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Eliminate a few lines of code by using the PTR_ERR_OR_ZERO() macro.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the devm_* managed version of the function to register the power
supply and remove the associated unregister function. This will simplify
error handling moving forward as it allows the unregister to happen
automatically. It also saves a few lines of code.
As this changes the order of putting the bq24257 into reset vs.
unregistering the power-supply during driver remove re-tested various
driver unload scenario to make sure that this doesn't cause any
unintended side effects such as erroneous interrupts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Streamline input current limit setup
The maximum amount of input current the charger should draw is dependent
on the power supply and should only be (re-)configured when the power
supply gets connected and disconnected. However the driver was also
lowering the bq24257's input current limit setting to 500mA when the
battery was removed and restored the previous setting according to the
power supply capabilities when the battery was reconnected although
these events are not impacting the amount of power that can be drawn
from the supply. Furthermore, a re-configuration of the input current
limit to 500mA when the battery gets disconnected is actually dangerous
if the limit was set higher previously and the system draws more than
500mA in which case the system voltage would be reduced in order to
maintain 500mA which could result in the system getting too low of a
supply to maintain operation. Last but not least the mechanism itself
used for battery re-connection detection did not work in corner cases
such as when the device's input current loop becomes active and the
bq24257 device clears its battery fault error resulting in incorrectly
reporting that the battery got reconnected.
This patches removes the impact the battery removal/insertion has on the
input current limit configured for the bq24257 and simplifies the
associated handler routine.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: bq24257: Remove IRQ config through stat-gpios
At the time the driver was written GpioInt resources in ACPI were not
passed to the driver in client->irq, as opposed to DT enumeration. To
accommodate this use case, a "stat-gpios" property was introduced to
allow configuring the IRQ.
However this issue with ACPI was fixed in commit "845c877 i2c / ACPI:
Assign IRQ for devices that have GpioInt automatically" and makes this
workaround no longer necessary, hence we can remove the support for the
"stat-gpios" property and the associated code from the bq24257 driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes: 74aab849f342 ('power: bq27xxx_battery: Cleanup health checking') Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-By: Pali Rohár <pali.rohar@gmail.com> Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Marek Belisko [Fri, 25 Sep 2015 20:20:45 +0000 (22:20 +0200)]
drivers: power: twl4030_charger: fix link problems when building as module
If either twl4030_charger or twl4030_madc is configured as MODULE,
we get build (link) errors.
To solve, the direct call of twl4030_get_madc_conversion() is replaced
by a call to iio_read_channel_processed().
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
wm831x_power: Use IRQF_ONESHOT to request threaded IRQs
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bbaf ("wm831x_power: Use genirq") Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds support for the tps65217 charger driver. This driver is
responsible for controlling the charger aspect of the tps65217 mfd.
Currently, this mainly consists of turning on and off the charger, but
some other features of the charger can be supported through this driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit b68c3161430a (bq2415x_charger: Allow to load and use driver even if
notify device is not registered yet) introduced null pointer dereference in
case bq is NULL. This patch fixes it.
Fixes: b68c3161430a ("bq2415x_charger: Allow to load and use driver even if notify device is not registered yet") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Andrew F. Davis [Tue, 22 Sep 2015 19:35:09 +0000 (14:35 -0500)]
power: bq27xxx_battery: Add support for additional bq27xxx family devices
Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.
To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Andrew F. Davis [Tue, 22 Sep 2015 19:35:06 +0000 (14:35 -0500)]
power: bq27x00_battery: Renaming for consistency
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Vaishali Thakkar [Thu, 13 Aug 2015 04:54:41 +0000 (10:24 +0530)]
power_supply: max8998: Use devm_power_supply_register
Use managed resource function devm_power_supply_register instead
of power_supply_register to simplify the error path by allowing
unregister to happen automatically on error. To be compatible with
the change, replace various gotos by direct returns and remove
unneeded label err.
Also, remove max8998_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
By accident I stumbled over a few misspelled words in the
charger-manager header file which this patch fixes. Namely:
- Extcon rather than Exton
- constraint rather than constratint
- existence rather than existance
- difference rather than diffential
While at it also add a missing space before a closing comment star
forward-slash.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
max8903_charger: Convert to using managed resources
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove max8903_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power/reset: at91-poweroff: get and use slow clock
Commit dca1a4b5ff6e ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91 shutdown
controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power/reset: at91-poweroff: allow compiling as a module
It was not possible to compile at91-poweroff as a module. Implement
.remove() to allow it. Also switch to module_platform_driver_probe() as it
is not hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit dca1a4b5ff6e ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91 reset
controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power/reset: at91-reset: allow compiling as a module
It was not possible to compile at91-reset as a module. Implement .remove()
to allow it. Also switch to module_platform_driver_probe() as it is not
hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
88pm860x_battery: Convert to using managed resources
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove pm860x_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
power: Remove unnecessary MODULE_ALIAS() for I2C drivers
These drivers already have an I2C device id table that is used to create
module aliases and the used MODULE_ALIAS() was either already in the I2C
table so it was redundant or wasn't a valid I2C id so it was never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Milo Kim [Tue, 25 Aug 2015 06:07:08 +0000 (15:07 +0900)]
power:lp8727_charger: parsing child node after getting debounce-ms
According to lp8727 bindings[*], charging parameter is optional.
So parsing can be skipped in case those properties are undefined.
However, 'debounce-ms' should be read prior to checking the properties.
Otherwise, 'debounce-ms' property will be ignored even it is configured
inside the DT.
So, counting child is processed after updating 'debounce-ms'.
Milo Kim [Tue, 25 Aug 2015 06:07:07 +0000 (15:07 +0900)]
power:lp8727_charger: use the private data instead of updating I2C device platform data
Currently, lp8727 charger driver parses the DT and copies values into the
'cl->dev.platform_data' if 'of_node' exists.
This may have architectural issue. Platform data is configurable through
the DT or I2C board info inside the platform area.
However, lp8727 driver changes this configuration when it is loaded.
The driver should get data from the platform side and use the private
data, 'lp8727_chg->pdata' instead of changing the original platform data.
_probe() procedure is changed as follows.
1. lp8727_parse_dt() returns the pointer of lp8727_platform_data.
The driver uses this allocated platform data. So it should keep
original platform data, 'dev->platform_data'.
2. In _probe(), check the return value of lp8727_parse_dt().
If an error is found, then exit as PTR_ERR(pdata).
3. If 'of_node' is not found, then the driver just gets the platform data
from the I2C device structure.
4. Map the platform data to private data structure.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Milo Kim <milo.kim@ti.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Hans de Goede [Sat, 1 Aug 2015 08:39:38 +0000 (10:39 +0200)]
power: Add an axp20x-usb-power driver
This adds a driver for the usb power_supply bits of the axp20x PMICs.
I initially started writing my own driver, before coming aware of
Bruno Prémont's excellent earlier RFC with a driver for this.
My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's
drvier has, so I've copied the code for those from his driver.
Note that the AC-power-supply and battery charger bits will need separate
drivers. Each one needs its own devictree child-node so that other
devicetree nodes can reference the right power-supply, and thus each one
will get its own mfd-cell / platform_device and platform-driver.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sre@kernel.org>
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three fixes and a resulting cleanup for -rc2:
- Andre Przywara reported that he was seeing a warning with the new
cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
use.
- Doug Anderson noticed that kgdb causes a "scheduling while atomic"
bug.
- OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
when enabling support to cover ARMv6 CPUs due to a kernel bug
leaking some conditional context into the signal handler"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
ARM: get rid of needless #if in signal handling code
ARM: fix Thumb2 signal handling when ARMv6 is enabled
Merge tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update contains 7 fixes for problems ranging from build failurs
to incorrect error reporting"
* tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: exec: revert to default emit rule
selftests: change install command to rsync
selftests: mqueue: simplify the Makefile
selftests: mqueue: allow extra cflags
selftests: rename jump label to static_keys
selftests/seccomp: add support for s390
seltests/zram: fix syntax error
Merge tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Included are: a somewhat late devfreq update which however is mostly
fixes and cleanups with one new thing only (the PPMUv2 support on
Exynos5433), an ACPI cpufreq driver fixup and two ACPI core cleanups
related to preprocessor directives.
Specifics:
- Fix a memory allocation size in the devfreq core (Xiaolong Ye).
- Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
Canillas).
- Add support for PPMUv2 ((Platform Performance Monitoring Unit
version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).
- Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).
- Assorted devfreq code cleanups and optimizations (Javi Merino,
MyungJoo Ham, Viresh Kumar).
- Fix up the ACPI cpufreq driver to use a more lightweight way to get
to its private data in the ->get() callback (Rafael J Wysocki).
- Fix a CONFIG_ prefix bug in one of the ACPI drivers and make the
ACPI subsystem use IS_ENABLED() instead of #ifdefs in function
bodies (Sudeep Holla)"
* tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
ACPI: int340x_thermal: add missing CONFIG_ prefix
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few driver fixes for tegra, rockchip, and st SoCs and a two-liner in
the framework to avoid oops when get_parent ops return out of range
values on tegra platforms"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
clk: check for invalid parent index of orphans in __clk_init()
clk: tegra: dfll: Properly protect OPP list
clk: rockchip: add critical clock for rk3368
Merge tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix module autoload for six OF platform drivers (aat1290, bcm6328,
bcm6358, ktd2692, max77693, ns2)
- aat1290: add missing static modifier
- ipaq-micro: add missing LEDS_CLASS dependency
- lp55xx: correct Kconfig dependecy for f/w user helper
* tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds:lp55xx: Correct Kconfig dependency for f/w user helper
leds: leds-ipaq-micro: Add LEDS_CLASS dependency
leds: aat1290: add 'static' modifier to init_mm_current_scale
leds: leds-ns2: Fix module autoload for OF platform driver
leds: max77693: Fix module autoload for OF platform driver
leds: ktd2692: Fix module autoload for OF platform driver
leds: bcm6358: Fix module autoload for OF platform driver
leds: bcm6328: Fix module autoload for OF platform driver
leds: aat1290: Fix module autoload for OF platform driver
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"The new hfi1 driver in staging/rdma has had a number of fixup patches
since being added to the tree. This is the first batch of those fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hfi: Properly set permissions for user device files
IB/hfi1: mask vs shift confusion
IB/hfi1: clean up some defines
IB/hfi1: info leak in get_ctxt_info()
IB/hfi1: fix a locking bug
IB/hfi1: checking for NULL instead of IS_ERR
IB/hfi1: fix sdma_descq_cnt parameter parsing
IB/hfi1: fix copy_to/from_user() error handling
IB/hfi1: fix pstateinfo from returning improperly byteswapped value
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- a boot regression (since v4.2) fix for some ARM configurations from
Tyler
- regression (since v4.1) fixes for mkfs.xfs on a DAX enabled device
from Jeff. These are tagged for -stable.
- a pair of locking fixes from Axel that are hidden from lockdep since
they involve device_lock(). The "btt" one is tagged for -stable, the
other only applies to the new "pfn" mechanism in v4.3.
- a fix for the pmem ->rw_page() path to use wmb_pmem() from Ross.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm: fix type cast in __pfn_to_phys()
pmem: add proper fencing to pmem_rw_page()
libnvdimm: pfn_devs: Fix locking in namespace_store
libnvdimm: btt_devs: Fix locking in namespace_store
blockdev: don't set S_DAX for misaligned partitions
dax: fix O_DIRECT I/O to the last block of a blockdev
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is a bit bigger than it should be, but I could (did) not want to
send it off last week due to both wanting extra testing, and expecting
a fix for the bounce regression as well. In any case, this contains:
- Fix for the blk-merge.c compilation warning on gcc 5.x from me.
- A set of back/front SG gap merge fixes, from me and from Sagi.
This ensures that we honor SG gapping for integrity payloads as
well.
- Two small fixes for null_blk from Matias, fixing a leak and a
capacity propagation issue.
- A blkcg fix from Tejun, fixing a NULL dereference.
- A fast clone optimization from Ming, fixing a performance
regression since the arbitrarily sized bio's were introduced.
- Also from Ming, a regression fix for bouncing IOs"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bounce_end_io
block: blk-merge: fast-clone bio when splitting rw bios
block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
block: Copy a user iovec if it includes gaps
block: Refuse adding appending a gapped integrity page to a bio
block: Refuse request/bio merges with gaps in the integrity payload
block: Check for gaps on front and back merges
null_blk: fix wrong capacity when bs is not 512 bytes
null_blk: fix memory leak on cleanup
block: fix bogus compiler warnings in blk-merge.c
Chris Mason [Fri, 18 Sep 2015 17:35:08 +0000 (13:35 -0400)]
fs-writeback: unplug before cond_resched in writeback_sb_inodes
Commit 505a666ee3fc ("writeback: plug writeback in wb_writeback() and
writeback_inodes_wb()") has us holding a plug during writeback_sb_inodes,
which increases the merge rate when relatively contiguous small files
are written by the filesystem. It helps both on flash and spindles.
For an fs_mark workload creating 4K files in parallel across 8 drives,
this commit improves performance ~9% more by unplugging before calling
cond_resched(). cond_resched() doesn't trigger an implicit unplug, so
explicitly getting the IO down to the device before scheduling reduces
latencies for anyone waiting on clean pages.
It also cuts down on how often we use kblockd to unplug, which means
less work bouncing from one workqueue to another.
Many more details about how we got here:
https://lkml.org/lkml/2015/9/11/570
Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various definitions of __pfn_to_phys() have been consolidated to
use a generic macro in include/asm-generic/memory_model.h. This hit
mainline in the form of 012dcef3f058 "mm: move __phys_to_pfn and
__pfn_to_phys to asm/generic/memory_model.h". When the generic macro
was implemented the type cast to phys_addr_t was dropped which caused
boot regressions on ARM platforms with more than 4GB of memory and
LPAE enabled.
It was suggested to use PFN_PHYS() defined in include/linux/pfn.h
as provides the correct logic and avoids further duplication.
Reported-by: kernelci.org bot <bot@kernelci.org> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tyler Baker <tyler.baker@linaro.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* pm-cpufreq:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
* pm-devfreq:
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes and cleanups from Michael Tsirkin:
"This fixes the virtio-test tool, and improves the error handling for
virtio-ccw"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: handle failures of READ_VQ_CONF ccw
tools/virtio: propagate V=X to kernel build
vhost: move features to core
tools/virtio: fix build after 4.2 changes
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Mostly stable material, a lot of ARM fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
sched: access local runqueue directly in single_task_running
arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
arm64: KVM: Remove all traces of the ThumbEE registers
arm: KVM: Disable virtual timer even if the guest is not using it
arm64: KVM: Disable virtual timer even if the guest is not using it
arm/arm64: KVM: vgic: Check for !irqchip_in_kernel() when mapping resources
KVM: s390: Replace incorrect atomic_or with atomic_andnot
arm: KVM: Fix incorrect device to IPA mapping
arm64: KVM: Fix user access for debug registers
KVM: vmx: fix VPID is 0000H in non-root operation
KVM: add halt_attempted_poll to VCPU stats
kvm: fix zero length mmio searching
kvm: fix double free for fast mmio eventfd
kvm: factor out core eventfd assign/deassign logic
kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
KVM: make the declaration of functions within 80 characters
KVM: arm64: add workaround for Cortex-A57 erratum #852523
KVM: fix polling for guest halt continued even if disable it
arm/arm64: KVM: Fix PSCI affinity info return value for non valid cores
arm64: KVM: set {v,}TCR_EL2 RES1 bits
...
Ira Weiny [Thu, 17 Sep 2015 17:47:49 +0000 (13:47 -0400)]
IB/hfi: Properly set permissions for user device files
Some of the device files are required to be user accessible for PSM while
most should remain accessible only by root.
Add a parameter to hfi1_cdev_init which controls if the user should have access
to this device which places it in a different class with the appropriate
devnode callback.
In addition set the devnode call back for the existing class to be a bit more
explicit for those permissions.
Finally remove the unnecessary null check before class_destroy
Tested-by: Donald Dutile <ddutile@redhat.com> Signed-off-by: Haralanov, Mitko (mitko.haralanov@intel.com) Signed-off-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dan Carpenter [Wed, 16 Sep 2015 16:02:54 +0000 (19:02 +0300)]
IB/hfi1: clean up some defines
I added spaces around operators so it matches kernel style because
normally "-1ULL" is a number and " - 1" is a subtract operation. Also
removed some superflous "ULL" types so "1ULL" becomes "1".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
Merge tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
sched: access local runqueue directly in single_task_running
Commit 2ee507c47293 ("sched: Add function single_task_running to let a task
check if it is the only task running on a cpu") referenced the current
runqueue with the smp_processor_id. When CONFIG_DEBUG_PREEMPT is enabled,
that is only allowed if preemption is disabled or the currrent task is
bound to the local cpu (e.g. kernel worker).
With commit f78195129963 ("kvm: add halt_poll_ns module parameter") KVM
calls single_task_running. If CONFIG_DEBUG_PREEMPT is enabled that
generates a lot of kernel messages.
To avoid adding preemption in that cases, as it would limit the usefulness,
we change single_task_running to access directly the cpu local runqueue.
Cc: Tim Chen <tim.c.chen@linux.intel.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@vger.kernel.org> Fixes: 2ee507c472939db4b146d545352b8a7c79ef47f8 Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge tag 'platform-drivers-x86-v4.3-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix an issue introduced by the previous major toshiba rework. Add a
quirk. Workaround a few platform specific firmware items. One
cleanup to wmi I inadvertently dropped from a previous pull request.
Details:
hp-wmi:
- limit hotkey enable
toshiba_acpi:
- Fix hotkeys registration on some toshiba models
- Fix USB Sleep and Music always disabled
wmi:
- Remove private %pUL implementation
asus-nb-wmi:
- Add wapf=4 quirk for X456UA/X456UF"
* tag 'platform-drivers-x86-v4.3-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
hp-wmi: limit hotkey enable
toshiba_acpi: Fix hotkeys registration on some toshiba models
toshiba_acpi: Fix USB Sleep and Music always disabled
wmi: Remove private %pUL implementation
asus-nb-wmi: Add wapf=4 quirk for X456UA/X456UF
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "mm: make sure all file VMAs have ->vm_ops set"
MAINTAINERS: update LTP mailing list
userfaultfd: add missing mmput() in error path
lib/string_helpers.c: fix infinite loop in string_get_size()
alpha: lib: export __delay
alpha: io: define ioremap_uc
kasan: fix last shadow judgement in memory_is_poisoned_16()
zram: fix possible use after free in zcomp_create()
Andrew Morton [Thu, 17 Sep 2015 23:02:00 +0000 (16:02 -0700)]
revert "mm: make sure all file VMAs have ->vm_ops set"
Revert commit 6dc296e7df4c "mm: make sure all file VMAs have ->vm_ops
set".
Will Deacon reports that it "causes some mmap regressions in LTP, which
appears to use a MAP_PRIVATE mmap of /dev/zero as a way to get anonymous
pages in some of its tests (specifically mmap10 [1])".
William Shuman reports Oracle crashes.
So revert the patch while we work out what to do.
Reported-by: William Shuman <wshuman3@gmail.com> Reported-by: Will Deacon <will.deacon@arm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/string_helpers.c: fix infinite loop in string_get_size()
Some string_get_size() calls (e.g.:
string_get_size(1, 512, STRING_UNITS_10, ..., ...)
string_get_size(15, 64, STRING_UNITS_10, ..., ...)
) result in an infinite loop. The problem is that if size is equal to
divisor[units]/blk_size and is smaller than divisor[units] we'll end
up with size == 0 when we start doing sf_cap calculations:
For string_get_size(1, 512, STRING_UNITS_10, ..., ...) case:
...
remainder = do_div(size, divisor[units]); -> size is 0, remainder is 1
remainder *= blk_size; -> remainder is 512
...
size *= blk_size; -> size is still 0
size += remainder / divisor[units]; -> size is still 0
The caller causing the issue is sd_read_capacity(), the problem was
noticed on Hyper-V, such weird size was reported by host when scanning
collides with device removal. This is probably a separate issue worth
fixing, this patch is intended to prevent the library routine from
infinite looping.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: James Bottomley <JBottomley@Odin.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__delay was not exported as a result while building with allmodconfig we
were getting build error of undefined symbol. __delay is being used by:
drivers/net/phy/mdio-octeon.c
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ioremap_uc was not defined and as a result while building with
allmodconfig were getting build error of: implicit declaration of
function 'ioremap_uc'.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kasan: fix last shadow judgement in memory_is_poisoned_16()
The shadow which correspond 16 bytes memory may span 2 or 3 bytes. If
the memory is aligned on 8, then the shadow takes only 2 bytes. So we
check "shadow_first_bytes" is enough, and need not to call
"memory_is_poisoned_1(addr + 15);". But the code "if
(likely(!last_byte))" is wrong judgement.
e.g. addr=0, so last_byte = 15 & KASAN_SHADOW_MASK = 7, then the code
will continue to call "memory_is_poisoned_1(addr + 15);"
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andrey Konovalov <adech.fo@gmail.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michal Marek <mmarek@suse.cz> Cc: <zhongjiang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luis Henriques [Thu, 17 Sep 2015 23:01:40 +0000 (16:01 -0700)]
zram: fix possible use after free in zcomp_create()
zcomp_create() verifies the success of zcomp_strm_{multi,single}_create()
through comp->stream, which can potentially be pointing to memory that
was freed if these functions returned an error.
While at it, replace a 'ERR_PTR(-ENOMEM)' by a more generic
'ERR_PTR(error)' as in the future zcomp_strm_{multi,siggle}_create()
could return other error codes. Function documentation updated
accordingly.
Fixes: beca3ec71fe5 ("zram: add multi stream functionality") Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not write initialize magic on systems that do not have
feature query 0xb. Fixes Bug #82451.
Redefine FEATURE_QUERY to align with 0xb and FEATURE2 with 0xd
for code clearity.
Add a new test function, hp_wmi_bios_2008_later() & simplify
hp_wmi_bios_2009_later(), which fixes a bug in cases where
an improper value is returned. Probably also fixes Bug #69131.
Add missing __init tag.
Signed-off-by: Kyle Evans <kvans32@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"These are both fixes to the new and improved keepalive2 behavior"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: advertise support for keepalive2
libceph: don't access invalid memory in keepalive2 path
Merge tag 'for-v4.3-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"twl4030-charger fixes"
* tag 'for-v4.3-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
twl4030_charger: fix another compile error
Revert "twl4030_charger: correctly handle -EPROBE_DEFER from devm_usb_get_phy_by_node"
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This addresses some problems with filesystem writeback due to the
recently merged hardware DBM patches, which caused us to treat some
read-only pages as dirty.
There are also some other, less significant fixes that are described
in the summary below:
A mixture of fixes for regressions introduced during the merge window,
some longer standing problems that we spotted and a couple of hardware
errata. The main changes are:
- Fix fallout from the h/w DBM patches, causing filesystem writeback
issues on both v8 and v8.1 CPUs
- Workaround for Cortex-A53 erratum #843419 in the module loader
- Fix for long-standing issue with compat big-endian signal handlers
using the saved floating point state"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: errata: add module build workaround for erratum #843419
arm64: compat: fix vfp save/restore across signal handlers in big-endian
arm64: cpu hotplug: ensure we mask out CPU_TASKS_FROZEN in notifiers
arm64: head.S: initialise mdcr_el2 in el2_setup
arm64: enable generic idle loop
arm64: pgtable: use a single bit for PTE_WRITE regardless of DBM
arm64: Fix pte_modify() to preserve the hardware dirty information
arm64: Fix the pte_hw_dirty() check when AF/DBM is enabled
arm64: dma-mapping: check whether cma area is initialized or not
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- misc fixes all around the map
- block non-root vm86(old) if mmap_min_addr != 0
- two small debuggability improvements
- removal of obsolete paravirt op
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Fix Geode LX timekeeping in the generic x86 build
x86/apic: Serialize LVTT and TSC_DEADLINE writes
x86/ioapic: Force affinity setting in setup_ioapic_dest()
x86/paravirt: Remove the unused pv_time_ops::get_tsc_khz method
x86/ldt: Fix small LDT allocation for Xen
x86/vm86: Fix the misleading CONFIG_VM86 Kconfig help text
x86/cpu: Print family/model/stepping in hex
x86/vm86: Block non-root vm86(old) if mmap_min_addr != 0
x86/alternatives: Make optimize_nops() interrupt safe and synced
x86/mm/srat: Print non-volatile flag in SRAT
x86/cpufeatures: Enable cpuid for Intel SHA extensions
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A fix for an abs()/abs64() bug that caused too slow NTP convergence on
32-bit kernels, plus a removal of an obsolete clockevents driver
facility after all users got converted during the merge window"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Remove unused set_mode() callback
time: Fix timekeeping_freqadjust()'s incorrect use of abs() instead of abs64()
projects / linux-beck.git / log