Retrieve the Interruption used by BCM device, which can be declared
as Interruption or GpioInt in the ACPI table.
Retrieve IRQ polarity from the ACPI table to use it for host_wake_active
parameter of Setup Sleep vendor specific command.
Configure BCM device to wake-up the host.
Enable IRQ wake while suspended.
Bluetooth: btintel: Add Device Configuration support
btintel_load_ddc_config retrieves the ddc file and sends its content
via DDC commands (opcode 0xfc8b).
The ddc file should contain one or more DDC structures.
A DDC structure is composed of the folowing fields:
field: | DDC LEN | DDC ID | DDC VALUE |
size: | 1 byte | 2 bytes | DDC LEN - 2 |
Vincent Stehlé [Thu, 3 Sep 2015 21:08:45 +0000 (23:08 +0200)]
Bluetooth: btintel: fix warning
Fix compilation the following compilation warning, which happens when
CONFIG_BT_INTEL is not set:
drivers/bluetooth/btintel.h:98:13: warning: ‘btintel_version_info’
defined but not used [-Wunused-function]
static void btintel_version_info(struct hci_dev *hdev,
struct intel_version *ver)
^
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Thu, 27 Aug 2015 19:49:20 +0000 (21:49 +0200)]
at86rf230: detailed edge triggered irq warning
This patch introduce a more detailed information why edge triggered
irq's are currently not recommended. It could be that rising/falling
edge detection can happen while the irq is disabled.
Suggested-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Thu, 27 Aug 2015 19:49:19 +0000 (21:49 +0200)]
at86rf230: add debugfs support
This patch introduce debugfs support for collect trac status stats. To
clear the stats ifdown the interface of at86rf230 and start the
interface again.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Thu, 27 Aug 2015 19:49:18 +0000 (21:49 +0200)]
at86rf230: interrupt tx with force trx_off
To abort a TX_ARET_BUSY state it's recommended to switch into TRX_OFF
state by doing STATE_TRX_FORCE_OFF. This patch will do always a TRX_OFF
state change when the transceiver stucks in any state. From TRX_OFF we
can switch to the states which are also possible by TX_ON state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Thu, 27 Aug 2015 19:49:17 +0000 (21:49 +0200)]
at86rf230: change trac status check behaviour
When transmit is done, indicated by trx_end irq, we do first a force
state change to TX_ON and then checking the trac status, if the trac
status is unequal zero we do a state change to TRX_OFF.
This patch changes to the following behaviour, we first check on trac
status after trx_end occurs and then doing a normal change to TX_ON
without do the state change to TRX_OFF when trac status is unequal zero.
The reasons are that the datasheet doesn't described when the trac
status register is cleared, we should doing to evaluate the trac status
at first. The reason to remove the TRX_OFF change if the trac status is
unequal to zero and it was force is the following paragraph inside The
at86rf2xx datasheets:
"Using FORCE_PLL_ON to interrupt an TX_ARET transaction, it is
recommended to check register bits [7:5] of register address 0x32 for
value 0. If this value is different, TRX_CMD sequence FORCE_TRX_OFF shall
be used immediately followed by TRX_CMD sequence PLL_ON. This performs a
state transition to PLL_ON."
The meaning is here "to interrupt an TX_ARET transaction" in case of
trx_end interrupt the "TX_ARET transaction" is already done and we don't
interrupt the "TX_ARET transaction" by doing the change to TX_ON (PLL_ON)
here. Additional I changed the force change to normal TX_ON which seems to
work here.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stefan Schmidt [Thu, 3 Sep 2015 12:54:19 +0000 (14:54 +0200)]
ieee802154: 6lowpan: use correct ESC value for dispatch
The ESC dispatch value has some history and it originally was 0x7f in rfc4944
(see section-5.1). With the release of rfc6282 this value got part of the
LOWPAN_IPHC range and was no longer available for ESC. Instead 0x40 was used
as replacement (see section-2 in rfc6282).
We have been checking the dispatch byte in an order where IPHC would always be
evaluated before ESC and thus we would never reach the ESC check as the IPHC
range already covers this value.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 18:05:42 +0000 (20:05 +0200)]
ieee802154: 6lowpan: fix drop return value
This patch changes the return value of lowpan packet receive handler to
the correct NET_RX_DROP instead RX_DROP.
This issue was detected by sparse and reported from Marcel:
net/ieee802154/6lowpan/rx.c:329:32: expected int
net/ieee802154/6lowpan/rx.c:329:32: got restricted lowpan_rx_result ...
Alexander Aring [Wed, 2 Sep 2015 12:21:30 +0000 (14:21 +0200)]
ieee802154: 6lowpan: remove packet type to host
This patch remove the packet_type to host and leave the mac pkt_type.
By running 'grep -r "pkt_type" net/ipv6', the IPv6 stack will evaluate
this value for PACKET_BROADCAST. Instead of overwriting this value we
will leave the mac value there which is broadcasts if the mac frame was
a broadcast frame.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:27 +0000 (14:21 +0200)]
ieee802154: 6lowpan: add handler for all dispatch values
This patch adds dummy handlers for all known IEEE 802.15.4 dispatch
values which prints a warning that we don't support these dispatches
right now. Also we add a warning to the RX_CONTINUE case inside of
lowpan_rx_handlers_result which should now never happend.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce an earlier check if a 6LoWPAN frame can be valid.
This contains at first for checking if the header contains a dispatch
byte and isn't the nalp dispatch value, which means it isn't a 6LoWPAN
packet. Also we add a check if we can derference the dispatch value by
checking if skb->len is unequal zero.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:25 +0000 (14:21 +0200)]
ieee820154: 6lowpan: dispatch evaluation rework
This patch complete reworks the evaluation of 6lowpan dispatch value by
introducing a receive handler mechanism for each dispatch value.
A list of changes:
- Doing uncompression on-the-fly when FRAG1 is received, this require
some special handling for 802.15.4 lltype in generic 6lowpan branch
for setting the payload length correct.
- Fix dispatch mask for fragmentation.
- Add IPv6 dispatch evaluation for FRAG1.
- Add skb_unshare for dispatch which might manipulate the skb data
buffer.
Cc: Jukka Rissanen <jukka.rissanen@linux.intel.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:24 +0000 (14:21 +0200)]
ieee802154: 6lowpan: earlier skb->dev switch
We should change the skb->dev pointer earlier to the lowpan interface
Sometimes we call iphc_decompress which also use some netdev printout
functionality. This patch will change that the correct interface will be
displayed in this case, which should be the lowpan interface.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:22 +0000 (14:21 +0200)]
ieee802154: 6lowpan: cleanup pull of iphc bytes
This patch cleanups the pull of the iphc bytes. We don't need to check
if the skb->len contains two bytes, this will be checked by
lowpan_fetch_skb_u8.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:20 +0000 (14:21 +0200)]
ieee802154: 6lowpan: remove EXPORT_SYMBOL
This function is used internally inside of ieee802154 6lowpan module
only and not outside of any other module. We don't need to export this
function then.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:18 +0000 (14:21 +0200)]
ieee802154: 6lowpan: remove check on null
This patch removes one check on null which should be already done by
checking before for ARPHRD_IEEE802154. All ARPHRD_IEEE802154 and
ARPHRD_IEEE802154_MONITOR should have wdev->ieee802154_ptr, where
ARPHRD_IEEE802154 is currently a node interface only.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:17 +0000 (14:21 +0200)]
ieee802154: 6lowpan: register packet layer while open
This patch moves the open count handling while doing open of a lowpan
interface. We need the packet handler register at first when one lowpan
interface is up. There exists a small case when all lowpan interfaces
are down and the 802154 packet layer is still registered. To reduce some
overhead we will register the packet layer when the first lowpan
interface comes up and unregister when the last interface will become down.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Wed, 2 Sep 2015 12:21:16 +0000 (14:21 +0200)]
ieee802154: 6lowpan: change dev vars to wdev and ldev
Inside the IEEE 802.15.4 6LoWPAN subsystem we use two interfaces which
are wpan and lowpan interfaces. Instead of using always the variable
name "dev" for both we rename the "dev" variable to wdev which means the
wpan net_device and ldev which means a lowpan net_device. This avoids
confusing and always looking back to see which net_device is meant by
the variable name "dev".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: btmrvl: skb resource leak, and double free.
if btmrvl_tx_pkt() is called, and the branch
if (skb_headroom(skb) < BTM_HEADER_LEN)
evaluates positive, a new skb is allocated via skb_realloc_headroom.
The original skb is stored in a tmp variable, before being free'd.
However on success, the new skb, is not free'd, nor is it
returned to the caller which will then double-free the original skb.
Simon Fels [Wed, 2 Sep 2015 10:10:12 +0000 (12:10 +0200)]
Bluetooth: close HCI device when user channel socket gets closed
With 9380f9eacfbbee701daa416edd6625efcd3e29e1 the order of unsetting
the HCI_USER_CHANNEL flag of the HCI device was reverted to ensure
the device is first closed before making it available again.
Due to hci_dev_close checking for HCI_USER_CHANNEL being set on the
device it was never really closed and was kept opened. We're now
calling hci_dev_do_close directly to make sure the device is correctly
closed and we keep the correct order to unset the flag on our device
object.
Signed-off-by: Simon Fels <simon.fels@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement runtime PM suspend/resume callbacks.
If LPM supported, controller is put into supsend after a delay of
inactivity (1s). Inactivity is based on LPM idle notification and
host TX traffic.
Add PM suspend/resume callbacks which call lpm_suspend/resume.
Add LPM ack in threaded IRQ handler to notify the controller that
resume is complete.
Protect hci_uart against concurrent removing during suspend/resume.
Add LPM PM suspend/resume/host_wake LPM functions.
A LPM transaction is composed with a LPM request and ack/response.
Host can send a LPM suspend/resume request to the controller which
should respond with a LPM ack.
If resume is requested by the controller (irq), host has to send a LPM
ack once resumed.
Loic Poulain [Sat, 29 Aug 2015 11:38:19 +0000 (13:38 +0200)]
Bluetooth: hci_intel: Introduce LPM support
Enable controller Low-Power-Mode if we have a pdev to manage host
wake-up. Once LPM is enabled, controller notifies its TX status via
a vendor specific packet (tx_idle/tx_active).
tx_active means that there is more data upcoming from controller.
tx_idle means that controller can be put in suspended state.
Loic Poulain [Sat, 29 Aug 2015 11:38:18 +0000 (13:38 +0200)]
Bluetooth: hci_intel: Retrieve host-wake IRQ
An IRQ can be retrieved from the pdev resources. This irq will be used
in case of LPM suspend mode to wake-up the host and resume the link.
This resource can be declared as a GPIO-Interrupt which requires to be
converted into IRQ.
Johan Hedberg [Sun, 30 Aug 2015 18:47:21 +0000 (21:47 +0300)]
Bluetooth: btusb: Detect new kind of counterfeit CSR controllers
Controllers claiming to be CSR with LMP subversion 0x0c5c don't
actually seem to be authentic CSR controllers. They also don't have
their USB bcdDevice value matching the LMP subversion like all other
CSR controllers:
HCI:
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c)
LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c)
Manufacturer: Cambridge Silicon Radio (10)
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink: RTEXT_FILTER_SKIP_STATS support to avoid dumping inet/inet6 stats
Many commonly used functions like getifaddrs() invoke RTM_GETLINK
to dump the interface information, and do not need the
the AF_INET6 statististics that are always returned by default
from rtnl_fill_ifinfo().
Computing the statistics can be an expensive operation that impacts
scaling, so it is desirable to avoid this if the information is
not needed.
This patch adds a the RTEXT_FILTER_SKIP_STATS extended info flag that
can be passed with netlink_request() to avoid statistics computation
for the ifinfo path.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 15 Sep 2015 20:25:03 +0000 (13:25 -0700)]
cdc: Fix build warning.
In file included from drivers/usb/gadget/function/u_serial.h:16:0,
from drivers/usb/gadget/function/f_acm.c:23:
>> include/linux/usb/cdc.h:47:5: warning: 'struct usb_interface' declared inside parameter list
int buflen);
^
>> include/linux/usb/cdc.h:47:5: warning: its scope is only this definition or declaration, which is probably not what you want
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code around the allocation and loops are a bit obfuscated.
Neaten it by using:
o kcalloc with decimal count and sizeof(u32)
o Decimal loop indexing and i++ not i += 4
o A promiscuous block using a similar style
to the multicast block
o Remove unnecessary variables
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 7 Sep 2015 09:46:44 +0000 (15:16 +0530)]
drivers: net: cpsw: Add support to drive gpios for ethernet to be functional
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset completes the set of available Address Translation Unit
operations.
These Marvell switches have 4 operations to flush or (re)move, all or
only non-static MAC addresses, from the entire set of databases or from
just a particular one.
The first 3 patches introduce a generic _mv88e6xxx_atu_flush_move
function. The 4 remaining patches update a few FID operations in the
driver on setup, when a port join or leave a VLAN, or change state.
This is a step forward improving the hardware bridging support in DSA
and 88E6352-compatible switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 4 Sep 2015 18:34:16 +0000 (14:34 -0400)]
net: dsa: mv88e6xxx: remove all MACs when disabling a port
When we're moving a port from Learning or Forwarding state to Disabled
or Blocking or Listening state, remove all non-static MAC addresses
mapped to this port in the entire set of databases, not only one.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 4 Sep 2015 18:34:15 +0000 (14:34 -0400)]
net: dsa: mv88e6xxx: remove addresses when a port leaves a VLAN
Add a new _mv88e6xxx_atu_move function to prepare the ATU data register
for the move operation. The ports vector will contain the source port
and destination port of the Move operation. If the destination port is
0xF, the MAC addresses mapped to the source port are removed for the
address database(s).
Then add a _mv88e6xxx_atu_remove wrapper to remove the MAC addresses
from a VLAN database that are mapped to a given port, when it leaves it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 4 Sep 2015 18:34:12 +0000 (14:34 -0400)]
net: dsa: mv88e6xxx: rework ATU Flush operation
These Marvell switches have 4 operations to flush or (re)move, all or
only non-static MAC addresses, from the entire set of databases or from
just a particular one.
The value of the EntryState bits will determine if the operation is
either a Flush (0x0) or a Move (0xF).
When moving entries from one port to another, entries will be removed if
the destination port is 0xF.
This patch renames these operations for consistency, add a new generic
_mv88e6xxx_atu_flush_move function, and change _mv88e6xxx_flush_fid to
use it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 4 Sep 2015 18:34:11 +0000 (14:34 -0400)]
net: dsa: mv88e6xxx: extract ATU data write access
Other ATU commands need to write the ATU data register. To ease the
introduction of such commands, extract the ATU data write access from
_mv88e6xxx_atu_load to its own function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 4 Sep 2015 18:34:10 +0000 (14:34 -0400)]
net: dsa: mv88e6xxx: extract FID write from ATU command
Not every ATU commands apply to an FID, thus remove the FID writing from
mv88e6xxx_atu_cmd and write it explicitly where needed, in order to ease
introduction of such commands.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 2 Sep 2015 20:58:36 +0000 (13:58 -0700)]
net: Allow user to get table id from route lookup
rt_fill_info which is called for 'route get' requests hardcodes the
table id as RT_TABLE_MAIN which is not correct when multiple tables
are used. Use the newly added table id in the rtable to send back
the correct table similar to what is done for IPv6.
To maintain current ABI a new request flag, RTM_F_LOOKUP_TABLE, is
added to indicate the actual table is wanted versus the hardcoded
response.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'sound-fix-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes since the last update: the HD-audio quirks
as usual with a USB-audio fix and a trivial fix for the old sparc
driver"
* tag 'sound-fix-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Change internal PCM order
ALSA: hda - Fix white noise on Dell M3800
ALSA: hda - Use ALC880_FIXUP_FUJITSU for FSC Amilo M1437
ALSA: hda - Enable headphone jack detect on old Fujitsu laptops
ALSA: sparc: amd7930: Fix module autoload for OF platform driver
ALSA: hda - Add some FIXUP quirks for white noise on Dell laptop.
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just a bunch of fixes to squeeze in before -rc1:
- three nouveau regression fixes
- one qxl regression fix
- a bunch of i915 fixes
... and some core displayport/atomic fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
drm/qxl: validate monitors config modes
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Dave Airlie [Fri, 11 Sep 2015 04:38:36 +0000 (14:38 +1000)]
Merge branch 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
three nouveau regression fixes.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
Merge branch 'for-4.3/blkcg' of git://git.kernel.dk/linux-block
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
dma-mapping: consolidate dma_set_mask
dma-mapping: consolidate dma_supported
dma-mapping: cosolidate dma_mapping_error
dma-mapping: consolidate dma_{alloc,free}_noncoherent
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
mm: make sure all file VMAs have ->vm_ops set
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
mm: mark most vm_operations_struct const
namei: fix warning while make xmldocs caused by namei.c
ipc: convert invalid scenarios to use WARN_ON
zlib_deflate/deftree: remove bi_reverse()
lib/decompress_unlzma: Do a NULL check for pointer
lib/decompressors: use real out buf size for gunzip with kernel
fs/affs: make root lookup from blkdev logical size
sysctl: fix int -> unsigned long assignments in INT_MIN case
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
kexec: align crash_notes allocation to make it be inside one physical page
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
kexec: split kexec_load syscall from kexec core code
...
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
Dave Airlie [Fri, 11 Sep 2015 00:52:37 +0000 (10:52 +1000)]
Merge tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel into drm-next
bunch of drm fixes.
* tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel:
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Dave Airlie [Fri, 11 Sep 2015 00:52:08 +0000 (10:52 +1000)]
Merge tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel into drm-next
Fixes headed for v4.3-rc1, including Maarten's DP MST state checker fix
you requested.
* tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
Jonathon Jongsma [Thu, 20 Aug 2015 19:04:32 +0000 (14:04 -0500)]
drm/qxl: validate monitors config modes
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"ARM:
- Full debug support for arm64
- Active state switching for timer interrupts
- Lazy FP/SIMD save/restore for arm64
- Generic ARMv8 target
PPC:
- Book3S: A few bug fixes
- Book3S: Allow micro-threading on POWER8
x86:
- Compiler warnings
Generic:
- Adaptive polling for guest halt"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (49 commits)
kvm: irqchip: fix memory leak
kvm: move new trace event outside #ifdef CONFIG_KVM_ASYNC_PF
KVM: trace kvm_halt_poll_ns grow/shrink
KVM: dynamic halt-polling
KVM: make halt_poll_ns per-vCPU
Silence compiler warning in arch/x86/kvm/emulate.c
kvm: compile process_smi_save_seg_64() only for x86_64
KVM: x86: avoid uninitialized variable warning
KVM: PPC: Book3S: Fix typo in top comment about locking
KVM: PPC: Book3S: Fix size of the PSPB register
KVM: PPC: Book3S HV: Exit on H_DOORBELL if HOST_IPI is set
KVM: PPC: Book3S HV: Fix race in starting secondary threads
KVM: PPC: Book3S: correct width in XER handling
KVM: PPC: Book3S HV: Fix preempted vcore stolen time calculation
KVM: PPC: Book3S HV: Fix preempted vcore list locking
KVM: PPC: Book3S HV: Implement H_CLEAR_REF and H_CLEAR_MOD
KVM: PPC: Book3S HV: Fix bug in dirty page tracking
KVM: PPC: Book3S HV: Fix race in reading change bit when removing HPTE
KVM: PPC: Book3S HV: Implement dynamic micro-threading on POWER8
KVM: PPC: Book3S HV: Make use of unused threads when running guests
...
Merge tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
1) Fix out-of-bounds array access in netfilter ipset, from Jozsef
Kadlecsik.
2) Use correct free operation on netfilter conntrack templates, from
Daniel Borkmann.
3) Fix route leak in SCTP, from Marcelo Ricardo Leitner.
4) Fix sizeof(pointer) in mac80211, from Thierry Reding.
5) Fix cache pointer comparison in ip6mr leading to missed unlock of
mrt_lock. From Richard Laing.
6) rds_conn_lookup() needs to consider network namespace in key
comparison, from Sowmini Varadhan.
7) Fix deadlock in TIPC code wrt broadcast link wakeups, from Kolmakov
Dmitriy.
8) Fix fd leaks in bpf syscall, from Daniel Borkmann.
9) Fix error recovery when installing ipv6 multipath routes, we would
delete the old route before we would know if we could fully commit
to the new set of nexthops. Fix from Roopa Prabhu.
10) Fix run-time suspend problems in r8152, from Hayes Wang.
11) In fec, don't program the MAC address into the chip when the clocks
are gated off. From Fugang Duan.
12) Fix poll behavior for netlink sockets when using rx ring mmap, from
Daniel Borkmann.
13) Don't allocate memory with GFP_KERNEL from get_stats64 in r8169
driver, from Corinna Vinschen.
14) In TCP Cubic congestion control, handle idle periods better where we
are application limited, in order to keep cwnd from growing out of
control. From Eric Dumzet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
tcp_cubic: better follow cubic curve after idle period
tcp: generate CA_EVENT_TX_START on data frames
xen-netfront: respect user provided max_queues
xen-netback: respect user provided max_queues
r8169: Fix sleeping function called during get_stats64, v2
ether: add IEEE 1722 ethertype - TSN
netlink, mmap: fix edge-case leakages in nf queue zero-copy
netlink, mmap: don't walk rx ring on poll if receive queue non-empty
cxgb4: changes for new firmware 1.14.4.0
net: fec: add netif status check before set mac address
r8152: fix the runtime suspend issues
r8152: split DRIVER_VERSION
ipv6: fix ifnullfree.cocci warnings
add microchip LAN88xx phy driver
stmmac: fix check for phydev being open
net: qlcnic: delete redundant memsets
net: mv643xx_eth: use kzalloc
net: jme: use kzalloc() instead of kmalloc+memset
net: cavium: liquidio: use kzalloc in setup_glist()
net: ipv6: use common fib_default_rule_pref
...
Almost everyone implements dma_set_mask the same way, although some time
that's hidden in ->set_dma_mask methods.
This patch consolidates those into a common implementation that either
calls ->set_dma_mask if present or otherwise uses the default
implementation. Some architectures used to only call ->set_dma_mask
after the initial checks, and those instance have been fixed to do the
full work. h8300 implemented dma_set_mask bogusly as a no-ops and has
been fixed.
Unfortunately some architectures overload unrelated semantics like changing
the dma_ops into it so we still need to allow for an architecture override
for now.
[jcmvbkbc@gmail.com: fix xtensa] Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Michal Simek <monstr@monstr.eu> Cc: Jonas Bonn <jonas@southpole.se> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures just call into ->dma_supported, but some also return 1
if the method is not present, or 0 if no dma ops are present (although
that should never happeb). Consolidate this more broad version into
common code.
Also fix h8300 which inorrectly always returned 0, which would have been
a problem if it's dma_set_mask implementation wasn't a similarly buggy
noop.
As a few architectures have much more elaborate implementations, we
still allow for arch overrides.
[jcmvbkbc@gmail.com: fix xtensa] Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Michal Simek <monstr@monstr.eu> Cc: Jonas Bonn <jonas@southpole.se> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures do not support non-coherent allocations and either
define dma_{alloc,free}_noncoherent to their coherent versions or stub
them out.
Openrisc uses dma_{alloc,free}_attrs to implement them, and only Mips
implements them directly.
This patch moves the Openrisc version to common code, and handles the
DMA_ATTR_NON_CONSISTENT case in the mips dma_map_ops instance.
Note that actual non-coherent allocations require a dma_cache_sync
implementation, so if non-coherent allocations didn't work on
an architecture before this patch they still won't work after it.
[jcmvbkbc@gmail.com: fix xtensa] Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Michal Simek <monstr@monstr.eu> Cc: Jonas Bonn <jonas@southpole.se> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.
This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.
This patch (of 5):
The coherent DMA allocator works the same over all architectures supporting
dma_map operations.
This patch consolidates them and converges the minor differences:
- the debug_dma helpers are now called from all architectures, including
those that were previously missing them
- dma_alloc_from_coherent and dma_release_from_coherent are now always
called from the generic alloc/free routines instead of the ops
dma-mapping-common.h always includes dma-coherent.h to get the defintions
for them, or the stubs if the architecture doesn't support this feature
- checks for ->alloc / ->free presence are removed. There is only one
magic instead of dma_map_ops without them (mic_dma_ops) and that one
is x86 only anyway.
Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags. An optional arch hook is provided
for that.
[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa] Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Michal Simek <monstr@monstr.eu> Cc: Jonas Bonn <jonas@southpole.se> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
Add the additional "vm_flags_t vm_flags" argument to do_mmap_pgoff(),
rename it to do_mmap(), and re-introduce do_mmap_pgoff() as a simple
wrapper on top of do_mmap(). Perhaps we should update the callers of
do_mmap_pgoff() and kill it later.
This way mpx_mmap() can simply call do_mmap(vm_flags => VM_MPX) and do not
play with vm internals.
After this change mmap_region() has a single user outside of mmap.c,
arch/tile/mm/elf.c:arch_setup_additional_pages(). It would be nice to
change arch/tile/ and unexport mmap_region().
[kirill@shutemov.name: fix build]
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Tested-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Minchan Kim <minchan@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
namei: fix warning while make xmldocs caused by namei.c
Fix the following warnings:
Warning(.//fs/namei.c:2422): No description found for parameter 'nd'
Warning(.//fs/namei.c:2422): Excess function parameter 'nameidata'
description in 'path_mountpoint'
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Considering Linus' past rants about the (ab)use of BUG in the kernel, I
took a look at how we deal with such calls in ipc. Given that any errors
or corruption in ipc code are most likely contained within the set of
processes participating in the broken mechanisms, there aren't really many
strong fatal system failure scenarios that would require a BUG call.
Also, if something is seriously wrong, ipc might not be the place for such
a BUG either.
1. For example, recently, a customer hit one of these BUG_ONs in shm
after failing shm_lock(). A busted ID imho does not merit a BUG_ON,
and WARN would have been better.
2. MSG_COPY functionality of posix msgrcv(2) for checkpoint/restore.
I don't see how we can hit this anyway -- at least it should be IS_ERR.
The 'copy' arg from do_msgrcv is always set by calling prepare_copy()
first and foremost. We could also probably drop this check altogether.
Either way, it does not merit a BUG_ON.
3. No ->fault() callback for the fs getting the corresponding page --
seems selfish to make the system unusable.
projects / linux-beck.git / log