Mathieu Poirier [Thu, 25 Aug 2016 21:19:14 +0000 (15:19 -0600)]
coresight: etm4x: cleaning up default filter configuration
The default filter configuration was hard to read and included
some redundancy. This patch attempts to stream line configuration
and improve readability.
Mathieu Poirier [Thu, 25 Aug 2016 21:19:13 +0000 (15:19 -0600)]
coresight: etm4x: split default and filter configuration
Splitting the steps involved in the configuration of a tracer.
The first part is generic and can be reused for both sysFS and
Perf methods.
The second part pertains to the configuration of filters
themselves where the source of the information used to
configure the filters will vary depending on the access
methods.
Mathieu Poirier [Thu, 25 Aug 2016 21:19:10 +0000 (15:19 -0600)]
coresight: etm-perf: pass struct perf_event to source::enable/disable()
With this commit [1] address range filter information is now found
in the struct hw_perf_event::addr_filters. As such pass the event
itself to the coresight_source::enable/disable() functions so that
both event attribute and filter can be accessible for configuration.
[1] 'commit 375637bc5249 ("perf/core: Introduce address range filtering")'
Sudeep Holla [Thu, 25 Aug 2016 21:19:09 +0000 (15:19 -0600)]
coresight: fix handling of ETM trace register access via sysfs
The ETM registers are classified into 2 categories: trace and management.
The core power domain contains most of the trace unit logic including
all(except TRCOSLAR and TRCOSLSR) the trace registers. The debug power
domain contains the external debugger interface including all management
registers.
This patch adds coresight unit specific function coresight_simple_func
which can be used for ETM trace registers by providing a ETM specific
read function which does smp cross call to ensure the trace core is
powered up before the register is accessed.
Sudeep Holla [Thu, 25 Aug 2016 21:19:08 +0000 (15:19 -0600)]
coresight: etm4x: request to retain power to the trace unit when active
The Coresight ETMv4 architecture provides a way to request to keep the
power to the trace unit. This might help to collect the traces without
the need to disable the CPU power management(entering/exiting deeper
idle states).
Trace PowerDown Control Register provides powerup request bit which when
set requests the system to retain power to the trace unit and emulate
the powerdown request.
Typically, a trace unit drives a signal to the power controller to
request that the trace unit core power domain is powered up. However,
if the trace unit and the CPU are in the same power domain then the
implementation might combine the trace unit power up status with a
signal from the CPU.
This patch requests to retain power to the trace unit when active and
to remove when inactive. Note this change will only request but the
behaviour depends on the implementation. However, it matches the
exact behaviour expected when the external debugger is connected with
respect to CPU power states.
Suzuki K Poulose [Thu, 25 Aug 2016 21:19:05 +0000 (15:19 -0600)]
coresight: Use local coresight_desc instances
Each coresight device prepares a description for coresight_register()
in struct coresight_desc. Once we register the device, the description is
useless and can be freed. The coresight_desc is small enough (48bytes on
64bit)i to be allocated on the stack. Hence use an automatic variable to
avoid a needless dynamic allocation and wasting the memory(which will only
be free'd when the device is destroyed).
Mathieu Poirier [Thu, 25 Aug 2016 21:19:02 +0000 (15:19 -0600)]
coresight: add PM runtime calls to coresight_simple_func()
It is mandatory to enable a coresight block's power domain before
trying to access management registers. Otherwise the transaction
simply stalls, leading to a system hang.
Mathieu Poirier [Thu, 25 Aug 2016 21:19:01 +0000 (15:19 -0600)]
coresight: delay initialisation when children are missing
Depending on when CoreSight device are discovered it is possible
that some IP block may be referencing devices that have not been
added to the bus yet. The end result is missing nodes in the
CoreSight topology even when the devices are present and properly
initialised.
This patch solves the problem by asking the driver core to
try initialising the device at a later time when the children
of a CoreSight node are missing.
Suzuki K Poulose [Thu, 25 Aug 2016 21:19:00 +0000 (15:19 -0600)]
coresight: Add better messages for coresight_timeout
When we encounter a timeout waiting for a status change via
coresight_timeout, the caller always print the offset which
was tried. This is pretty much useless as it doesn't specify
the bit position we wait for. Also, one needs to lookup the
TRM to figure out, what was wrong. This patch changes all
such error messages to print something more meaningful.
[7:4] Revision
[3] JEDEC 0b1 res1. Indicates a JEP106 identity code is used
[2:0] DES_1 0b011 ARM Limited. This is bits[6:4] of JEP106 ID code
The existing table entry checks only the bits [1:0], which is not
sufficient enough. Fix it to match bits [3:0], just like the other
entries do. While at it, correct the comment for A57 and the A53 entry.
Suzuki K Poulose [Thu, 25 Aug 2016 21:18:57 +0000 (15:18 -0600)]
coresight: tmc: Limit the trace to available data
At present the ETF or ETR gives out the entire device
buffer, even if there is less or even no trace data
available. This patch limits the trace data given out to
the actual trace data collected.
Suzuki K Poulose [Thu, 25 Aug 2016 21:18:56 +0000 (15:18 -0600)]
coresight: Fix csdev connections initialisation
This is a cleanup patch.
coresight_device->conns holds an array to point to the devices
connected to the OUT ports of a component. Sinks, e.g ETR, do not
have an OUT port (nr_outport = 0), as it streams the trace to
memory via AXI.
At coresight_register() we do :
conns = kcalloc(csdev->nr_outport, sizeof(*conns), GFP_KERNEL);
if (!conns) {
ret = -ENOMEM;
goto err_kzalloc_conns;
}
For ETR, since the total size requested for kcalloc is zero, the return
value is, ZERO_SIZE_PTR ( != NULL). Hence, csdev->conns = ZERO_SIZE_PTR
which cannot be verified later to contain a valid pointer. The code which
accesses the csdev->conns is bounded by the csdev->nr_outport check,
hence we don't try to dereference the ZERO_SIZE_PTR. This patch cleans
up the csdev->conns initialisation to make sure we initialise it
properly(i.e, either NULL or valid conns array).
Suzuki K Poulose [Thu, 25 Aug 2016 21:18:54 +0000 (15:18 -0600)]
coresight: Remove erroneous dma_free_coherent in tmc_probe
commit de5461970b3e9e194 ("coresight: tmc: allocating memory when needed")
removed the static allocation of buffer for the trace data in ETR mode in
tmc_probe. However it failed to remove the "devm_free_coherent" in
tmc_probe when the probe fails due to other reasons. This patch gets
rid of the incorrect dma_free_coherent() call.
Sudeep Holla [Thu, 25 Aug 2016 21:18:53 +0000 (15:18 -0600)]
coresight: always use stashed trace id value in etm4_trace_id
etm4_trace_id is not guaranteed to be executed on the CPU whose ETM is
being accessed. This leads to exception similar to below one if the
CPU whose ETM is being accessed is in deeper idle states. So it must
be executed on the CPU whose ETM is being accessed.
Unhandled fault: synchronous external abort (0x96000210) at 0xffff000008db4040
Internal error: : 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 5 PID: 5979 Comm: etm.sh Not tainted 4.7.0-rc3 #159
Hardware name: ARM Juno development board (r2) (DT)
task: ffff80096dd34b00 ti: ffff80096dfe4000 task.ti: ffff80096dfe4000
PC is at etm4_trace_id+0x5c/0x90
LR is at etm4_trace_id+0x3c/0x90
Call trace:
etm4_trace_id+0x5c/0x90
coresight_id_match+0x78/0xa8
bus_for_each_dev+0x60/0xa0
coresight_enable+0xc0/0x1b8
enable_source_store+0x3c/0x70
dev_attr_store+0x18/0x28
sysfs_kf_write+0x48/0x58
kernfs_fop_write+0x14c/0x1e0
__vfs_write+0x1c/0x100
vfs_write+0xa0/0x1b8
SyS_write+0x44/0xa0
el0_svc_naked+0x24/0x28
However, TRCTRACEIDR is not guaranteed to hold the previous programmed
trace id if it enters deeper idle states. Further, the trace id that is
computed in etm4_init_trace_id is programmed into TRCTRACEIDR only in
etm4_enable_hw which happens much later in the sequence after
coresight_id_match is executed from enable_source_store.
This patch simplifies etm4_trace_id by returning the stashed trace id
value similar to etm4_cpu_id.
Chunyan Zhang [Thu, 25 Aug 2016 21:18:52 +0000 (15:18 -0600)]
coresight-stm: support mmapping channel regions with mmio_addr
CoreSight STM device allows direct mapping of the channel regions to
userspace for zero-copy writing. To support this ability, the STM
framework has provided a hook 'mmio_addr', this patch just implemented
this hook for CoreSight STM.
This patch also added an item into 'channel_space' to save the physical
base address of channel region which mmap operation needs to know.
Sudeep Holla [Thu, 25 Aug 2016 21:18:51 +0000 (15:18 -0600)]
coresight: access conn->child_name only if it's initialised
If the addition of the coresight devices get deferred, then there's a
window before child_name is populated by of_get_coresight_platform_data
from the respective component driver's probe and the attempted to access
the same from coresight_orphan_match resulting in kernel NULL pointer
dereference as below:
Unable to handle kernel NULL pointer dereference at virtual address 0x0
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1038 Comm: kworker/0:1 Not tainted 4.7.0-rc3 #124
Hardware name: ARM Juno development board (r2) (DT)
Workqueue: events amba_deferred_retry_func
PC is at strcmp+0x1c/0x160
LR is at coresight_orphan_match+0x7c/0xd0
Call trace:
strcmp+0x1c/0x160
bus_for_each_dev+0x60/0xa0
coresight_register+0x264/0x2e0
tmc_probe+0x130/0x310
amba_probe+0xd4/0x1c8
driver_probe_device+0x22c/0x418
__device_attach_driver+0xbc/0x158
bus_for_each_drv+0x58/0x98
__device_attach+0xc4/0x160
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
device_add+0x344/0x580
amba_device_try_add+0x194/0x238
amba_deferred_retry_func+0x48/0xd0
process_one_work+0x118/0x378
worker_thread+0x48/0x498
kthread+0xd0/0xe8
ret_from_fork+0x10/0x40
This patch adds a check for non-NULL conn->child_name before accessing
the same.
Alex Ng [Wed, 24 Aug 2016 23:23:13 +0000 (16:23 -0700)]
Drivers: hv: balloon: Use available memory value in pressure report
Reports for available memory should use the si_mem_available() value.
The previous freeram value does not include available page cache memory.
Signed-off-by: Alex Ng <alexng@messages.microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Wed, 24 Aug 2016 23:23:12 +0000 (16:23 -0700)]
Drivers: hv: balloon: replace ha_region_mutex with spinlock
lockdep reports possible circular locking dependency when udev is used
for memory onlining:
systemd-udevd/3996 is trying to acquire lock:
((memory_chain).rwsem){++++.+}, at: [<ffffffff810d137e>] __blocking_notifier_call_chain+0x4e/0xc0
but task is already holding lock:
(&dm_device.ha_region_mutex){+.+.+.}, at: [<ffffffffa015382e>] hv_memory_notifier+0x5e/0xc0 [hv_balloon]
...
which is probably a false positive because we take and release
ha_region_mutex from memory notifier chain depending on the arg. No real
deadlocks were reported so far (though I'm not really sure about
preemptible kernels...) but we don't really need to hold the mutex
for so long. We use it to protect ha_region_list (and its members) and the
num_pages_onlined counter. None of these operations require us to sleep
and nothing is slow, switch to using spinlock with interrupts disabled.
While on it, replace list_for_each -> list_for_each_entry as we actually
need entries in all these cases, drop meaningless list_empty() checks.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Wed, 24 Aug 2016 23:23:11 +0000 (16:23 -0700)]
Drivers: hv: balloon: don't wait for ol_waitevent when memhp_auto_online is enabled
With the recently introduced in-kernel memory onlining
(MEMORY_HOTPLUG_DEFAULT_ONLINE) these is no point in waiting for pages
to come online in the driver and we can get rid of the waiting.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the host doesn't specify hot add regions we're trying to create
128Mb-aligned region covering the first request, we create the 0x108000 -
0x160000 region and we add 0x108000 - 0x158e00 memory. The second request
passes the pfn_covered() check, we enlarge the region to 0x108000 -
0x190000 and add 0x158e00 - 0x188200 memory. The problem emerges with the
third request as it starts at 0x188400 so there is a 0x200 gap which is
not covered. As the end of our region is 0x190000 now it again passes the
pfn_covered() check were we just adjust the covered_end_pfn and make it
0x188400 instead of 0x188200 which means that we'll try to online
0x188200-0x188400 pages but these pages were never assigned to us and we
crash.
We can't react to such requests by creating new hot add regions as it may
happen that the whole suggested range falls into the previously identified
128Mb-aligned area so we'll end up adding nothing or create intersecting
regions and our current logic doesn't allow that. Instead, create a list of
such 'gaps' and check for them in the page online callback.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Wed, 24 Aug 2016 23:23:09 +0000 (16:23 -0700)]
Drivers: hv: balloon: keep track of where ha_region starts
Windows 2012 (non-R2) does not specify hot add region in hot add requests
and the logic in hot_add_req() is trying to find a 128Mb-aligned region
covering the request. It may also happen that host's requests are not 128Mb
aligned and the created ha_region will start before the first specified
PFN. We can't online these non-present pages but we don't remember the real
start of the region.
This is a regression introduced by the commit 5abbbb75d733 ("Drivers: hv:
hv_balloon: don't lose memory when onlining order is not natural"). While
the idea of keeping the 'moving window' was wrong (as there is no guarantee
that hot add requests come ordered) we should still keep track of
covered_start_pfn. This is not a revert, the logic is different.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tools: hv: kvp: ensure kvp device fd is closed on exec
KVP daemon does fork()/exec() (with popen()) so we need to close our fds
to avoid sharing them with child processes. The immediate implication of
not doing so I see is SELinux complaining about 'ip' trying to access
'/dev/vmbus/hv_kvp'.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Implement a mechanism to tag the channel for low latency
On Hyper-V, performance critical channels use the monitor
mechanism to signal the host when the guest posts mesages
for the host. This mechanism minimizes the hypervisor intercepts
and also makes the host more efficient in that each time the
host is woken up, it processes a batch of messages as opposed to
just one. The goal here is improve the throughput and this is at
the expense of increased latency.
Implement a mechanism to let the client driver decide if latency
is important.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Fri, 10 Jun 2016 01:47:24 +0000 (18:47 -0700)]
Drivers: hv: vmbus: fix the race when querying & updating the percpu list
There is a rare race when we remove an entry from the global list
hv_context.percpu_list[cpu] in hv_process_channel_removal() ->
percpu_channel_deq() -> list_del(): at this time, if vmbus_on_event() ->
process_chn_event() -> pcpu_relid2channel() is trying to query the list,
we can get the kernel fault.
Similarly, we also have the issue in the code path: vmbus_process_offer() ->
percpu_channel_enq().
We can resolve the issue by disabling the tasklet when updating the list.
The patch also moves vmbus_release_relid() to a later place where
the channel has been removed from the per-cpu and the global lists.
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Fri, 10 Jun 2016 00:08:57 +0000 (17:08 -0700)]
Drivers: hv: utils: fix a race on userspace daemons registration
Background: userspace daemons registration protocol for Hyper-V utilities
drivers has two steps:
1) daemon writes its own version to kernel
2) kernel reads it and replies with module version
at this point we consider the handshake procedure being completed and we
do hv_poll_channel() transitioning the utility device to HVUTIL_READY
state. At this point we're ready to handle messages from kernel.
When hvutil_transport is in HVUTIL_TRANSPORT_CHARDEV mode we have a
single buffer for outgoing message. hvutil_transport_send() puts to this
buffer and till the buffer is cleared with hvt_op_read() returns -EFAULT
to all consequent calls. Host<->guest protocol guarantees there is no more
than one request at a time and we will not get new requests till we reply
to the previous one so this single message buffer is enough.
Now to the race. When we finish negotiation procedure and send kernel
module version to userspace with hvutil_transport_send() it goes into the
above mentioned buffer and if the daemon is slow enough to read it from
there we can get a collision when a request from the host comes, we won't
be able to put anything to the buffer so the request will be lost. To
solve the issue we need to know when the negotiation is really done (when
the version message is read by the daemon) and transition to HVUTIL_READY
state after this happens. Implement a callback on read to support this.
Old style netlink communication is not affected by the change, we don't
really know when these messages are delivered but we don't have a single
message buffer there.
Reported-by: Barry Davis <barry_davis@stormagic.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Fri, 10 Jun 2016 00:08:56 +0000 (17:08 -0700)]
Drivers: hv: get rid of timeout in vmbus_open()
vmbus_teardown_gpadl() can result in infinite wait when it is called on 5
second timeout in vmbus_open(). The issue is caused by the fact that gpadl
teardown operation won't ever succeed for an opened channel and the timeout
isn't always enough. As a guest, we can always trust the host to respond to
our request (and there is nothing we can do if it doesn't).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: get rid of redundant messagecount in create_gpadl_header()
We use messagecount only once in vmbus_establish_gpadl() to check if
it is safe to iterate through the submsglist. We can just initialize
the list header in all cases in create_gpadl_header() instead.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we crash from NMI context (e.g. after NMI injection from host when
'sysctl -w kernel.unknown_nmi_panic=1' is set) we hit
kernel BUG at mm/vmalloc.c:1530!
as vfree() is denied. While the issue could be solved with in_nmi() check
instead I opted for skipping vfree on all sorts of crashes to reduce the
amount of work which can cause consequent crashes. We don't really need to
free anything on crash.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Metcalf [Thu, 28 Jul 2016 19:07:04 +0000 (15:07 -0400)]
tile-srom: avoid krealloc(... __GFP_ZERO) pattern
Joe Perches points out [1] that this pattern isn't currently safe.
This driver doesn't really need the zeroing semantic anyway;
by restructuring the code slightly we can initialize all the
fields of the structure up front instead.
Arnd Bergmann [Thu, 16 Jun 2016 11:38:24 +0000 (13:38 +0200)]
mic: remove unused function arg
When building with W=1, the __scif_rma_destroy_tcw function
causes a harmless warning about an argument variable that is
modified but not used:
drivers/misc/mic/scif/scif_dma.c: In function ‘__scif_rma_destroy_tcw’:
drivers/misc/mic/scif/scif_dma.c:118:27: error: parameter ‘ep’ set but not used [-Werror=unused-but-set-parameter]
In this case, we can just remove the argument, since all callers
are in the same file.
mei: amthif: fix deadlock in initialization during a reset
The device lock was unnecessary obtained in bus rescan work before the
amthif client search. That causes incorrect lock ordering and task
hang:
...
[88004.613213] INFO: task kworker/1:14:21832 blocked for more than 120 seconds.
...
[88004.645934] Workqueue: events mei_cl_bus_rescan_work
...
The correct lock order is
cl_bus_lock
device_lock
me_clients_rwsem
Move device_lock into amthif init function that called
after me_clients_rwsem is released.
This fixes regression introduced by commit:
commit 025fb792bac3 ("mei: split amthif client init from end of clients enumeration")
Cc: <stable@vger.kernel.org> # 4.6+ Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_amthif_read have only one difference from mei_read, it is not
calling mei_read_start().
Make mei_read_start return immediately for amthif client and drop the
special mei_amthif_read function.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FW supports only one pending read per host client, in order to
support issuing of consecutive reads the driver queues read requests
internally and send them to the firmware after pending one has
completed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Mon, 25 Jul 2016 22:06:05 +0000 (01:06 +0300)]
mei: add wrapper for queuing control commands.
Enclose the boiler plate code of allocating a control/hbm command cb
and enqueueing it onto ctrl_wr.list in a convenient wrapper
mei_cl_enqueue_ctrl_wr_cb().
This is a preparatory patch for enabling consecutive reads.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Mon, 25 Jul 2016 22:06:04 +0000 (01:06 +0300)]
mei: use consistent naming for TX control flow credits
With the introduction of the receive control flow credits prefixed with
rx_ we add tx_ prefix to the variables and function used for tracking
the transmit control flow credits.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use RX flow control counter in the host client structure to
track the number of simultaneous outstanding reads.
This eliminates search in queues and makes ground for
enabling for parallel read.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei: prepare read cb for fixed address clients on the receive path only.
The read callbacks for the fixed address clients, that don't have flow
control are built now on the receive path. In order to have a single
allocation place we remove the allocation from the read request.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei: drop redundant krealloc and checks in irq read
The read callback is always prepared with MTU-sized buffer and the FW
can't send more than the MTU in one message.
Checking for buffer existence and krealloc to increase receive buffer
size are redundant and may be safely discarded.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei: add read callback on demand for fixed_address clients
The Fixed address clients do not work with the flow control, and the
packet RX callback was allocated upon TX with anticipation of a
following RX. This won't work if the clients with unsolicited Rx. Rather
than preparing read callback upon a write we allocate one directly on
the reciev path if one doesn't exists.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei: add file pointer to the host client structure
Store the file associated with a client in the host client structure,
this enables dropping the special amthif client file pointer from struct
mei_device, and this is also a preparation for changing the way rx
packet allocation for fixed_address clients
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the course of the read flow we want to wait for read completion only
if the read queue is empty.
However the calling list_empty(&cl->rd_completed) is a duplication as the
same check was performed by mei_cl_read_cb() and the waiting is skipped
if it returns not NULL.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_io_cb_alloc_buf have a single caller :mei_cl_alloc_cb. After amthif
stopped using it, the code can be integrated into the caller and the
function can be dropped.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the poll function is bailing early for amthif client and
ignores requests for async events notifications.
Move async event processing before amthif to enable async events
notifications on amthif client.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iamthif_current_cb was used in request cancel in amthif code.
Now a canceled request is discarded only at the end of the processing
and the variable lost its purpose and can be safely removed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, all requests cancelled by the user are immediately removed
from the queues. Such removal can cause unexpected behavior in the case
when a request is partially written or a reply is received after the
request is cancelled. To resolve this a request is always fully
processed and the result is discarded in case the request was canceled.
This completes the partial fix in commit: 9d04ee1 ("mei: amthif: discard not read messages")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMTHIF code now uses read completed queue to store replies from the FW.
It is possible to send the next request as soon as a read from the FW is
completed. With these changes we don't need the READ_COMPLETE state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkkconfigsymblos: consistent symbol terminology
'symbol' and 'feature' are used synonymously to refer to Kconfig symbols
(configs, menus, etc.). Use the term 'symbol' to have a consistent
terminology and to make the code more comprehensible.
Linus Torvalds [Mon, 15 Aug 2016 02:01:31 +0000 (19:01 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- Fix a race condition when updating cooling device, which may lead to
a situation where a thermal governor never updates the cooling
device. From Michele Di Giorgio.
- Fix a zero division error when disabling the forced idle injection
from the intel powerclamp. From Petr Mladek.
- Add suspend/resume callback for intel_pch_thermal thermal driver.
From Srinivas Pandruvada.
- Another two fixes for clocking cooling driver and hwmon sysfs I/F.
From Michele Di Giorgio and Kuninori Morimoto.
[ Hmm. That suspend/resume callback for intel_pch_thermal doesn't look
like a fix, but I'm letting it slide.. - Linus ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: clock_cooling: Fix missing mutex_init()
thermal: hwmon: EXPORT_SYMBOL_GPL for thermal hwmon sysfs
thermal: fix race condition when updating cooling device
thermal/powerclamp: Prevent division by zero when counting interval
thermal: intel_pch_thermal: Add suspend/resume callback
Linus Torvalds [Mon, 15 Aug 2016 01:54:37 +0000 (18:54 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu fix from Greg Ungerer:
"This contains only a single fix for a register corruption problem on
certain types of m68k flat format binaries"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix user a5 register being overwritten
Linus Torvalds [Sun, 14 Aug 2016 02:39:38 +0000 (19:39 -0700)]
Merge tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull h8300 and unicore32 architecture fixes from Guenter Roeck:
"Two patches to fix h8300 and unicore32 builds.
unicore32 builds have been broken since v4.6. The fix has been
available in -next since March of this year.
h8300 builds have been broken since the last commit window. The fix
has been available in -next since June of this year"
* tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
h8300: Add missing include file to asm/io.h
unicore32: mm: Add missing parameter to arch_vma_access_permitted
Linus Torvalds [Sat, 13 Aug 2016 16:56:45 +0000 (09:56 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- an NVMe fix from Gabriel, fixing a suspend/resume issue on some
setups
- addition of a few missing entries in the block queue sysfs
documentation, from Joe
- a fix for a sparse shadow warning for the bvec iterator, from
Johannes
- a writeback deadlock involving raid issuing barriers, and not
flushing the plug when we wakeup the flusher threads. From
Konstantin
- a set of patches for the NVMe target/loop/rdma code, from Roland and
Sagi
* 'for-linus' of git://git.kernel.dk/linux-block:
bvec: avoid variable shadowing warning
doc: update block/queue-sysfs.txt entries
nvme: Suspend all queues before deletion
mm, writeback: flush plugged IO in wakeup_flusher_threads()
nvme-rdma: Remove unused includes
nvme-rdma: start async event handler after reconnecting to a controller
nvmet: Fix controller serial number inconsistency
nvmet-rdma: Don't use the inline buffer in order to avoid allocation for small reads
nvmet-rdma: Correctly handle RDMA device hot removal
nvme-rdma: Make sure to shutdown the controller if we can
nvme-loop: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Free the I/O tags when we delete the controller
nvme-rdma: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Fix device removal handling
nvme-rdma: Queue ns scanning after a sucessful reconnection
nvme-rdma: Don't leak uninitialized memory in connect request private data
Guenter Roeck [Thu, 9 Jun 2016 03:11:58 +0000 (20:11 -0700)]
h8300: Add missing include file to asm/io.h
h8300 builds fail with
arch/h8300/include/asm/io.h:9:15: error: unknown type name ‘u8’
arch/h8300/include/asm/io.h:15:15: error: unknown type name ‘u16’
arch/h8300/include/asm/io.h:21:15: error: unknown type name ‘u32’
Guenter Roeck [Mon, 21 Mar 2016 11:20:53 +0000 (04:20 -0700)]
unicore32: mm: Add missing parameter to arch_vma_access_permitted
unicore32 fails to compile with the following errors.
mm/memory.c: In function ‘__handle_mm_fault’:
mm/memory.c:3381: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘check_vma_flags’:
mm/gup.c:456: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘vma_permits_fault’:
mm/gup.c:640: error:
too many arguments to function ‘arch_vma_access_permitted’
Linus Torvalds [Fri, 12 Aug 2016 23:28:41 +0000 (16:28 -0700)]
Merge tag 'nfsd-4.8-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Fixes for the dentry refcounting leak I introduced in 4.8-rc1, and for
races in the LOCK code which appear to go back to the big nfsd state
lock removal from 3.17"
* tag 'nfsd-4.8-1' of git://linux-nfs.org/~bfields/linux:
nfsd: don't return an unhashed lock stateid after taking mutex
nfsd: Fix race between FREE_STATEID and LOCK
nfsd: fix dentry refcounting on create
Linus Torvalds [Fri, 12 Aug 2016 23:23:58 +0000 (16:23 -0700)]
Merge tag 'pm-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Two hibernation fixes allowing it to work with the recently added
randomization of the kernel identity mapping base on x86-64 and one
cpufreq driver regression fix.
Specifics:
- Fix the x86 identity mapping creation helpers to avoid the
assumption that the base address of the mapping will always be
aligned at the PGD level, as it may be aligned at the PUD level if
address space randomization is enabled (Rafael Wysocki).
- Fix the hibernation core to avoid executing tracing functions
before restoring the processor state completely during resume
(Thomas Garnier).
- Fix a recently introduced regression in the powernv cpufreq driver
that causes it to crash due to an out-of-bounds array access
(Akshay Adiga)"
* tag 'pm-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
cpufreq: powernv: Fix crash in gpstate_timer_handler()
Linus Torvalds [Fri, 12 Aug 2016 21:31:10 +0000 (14:31 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This is bigger than usual - the reason is partly a pent-up stream of
fixes after the merge window and partly accidental. The fixes are:
- five patches to fix a boot failure on Andy Lutomirsky's laptop
- four SGI UV platform fixes
- KASAN fix
- warning fix
- documentation update
- swap entry definition fix
- pkeys fix
- irq stats fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/x2apic, smp/hotplug: Don't use before alloc in x2apic_cluster_probe()
x86/efi: Allocate a trampoline if needed in efi_free_boot_services()
x86/boot: Rework reserve_real_mode() to allow multiple tries
x86/boot: Defer setup_real_mode() to early_initcall time
x86/boot: Synchronize trampoline_cr4_features and mmu_cr4_features directly
x86/boot: Run reserve_bios_regions() after we initialize the memory map
x86/irq: Do not substract irq_tlb_count from irq_call_count
x86/mm: Fix swap entry comment and macro
x86/mm/kaslr: Fix -Wformat-security warning
x86/mm/pkeys: Fix compact mode by removing protection keys' XSAVE buffer manipulation
x86/build: Reduce the W=1 warnings noise when compiling x86 syscall tables
x86/platform/UV: Fix kernel panic running RHEL kdump kernel on UV systems
x86/platform/UV: Fix problem with UV4 BIOS providing incorrect PXM values
x86/platform/UV: Fix bug with iounmap() of the UV4 EFI System Table causing a crash
x86/platform/UV: Fix problem with UV4 Socket IDs not being contiguous
x86/entry: Clarify the RF saving/restoring situation with SYSCALL/SYSRET
x86/mm: Disable preemption during CR3 read+write
x86/mm/KASLR: Increase BRK pages for KASLR memory randomization
x86/mm/KASLR: Fix physical memory calculation on KASLR memory randomization
x86, kasan, ftrace: Put APIC interrupt handlers into .irqentry.text
Linus Torvalds [Fri, 12 Aug 2016 20:55:06 +0000 (13:55 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc fixes: a /dev/rtc regression fix, two APIC timer period
calibration fixes, an ARM clocksource driver fix and a NOHZ
power use regression fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Fix /dev/rtc breakage caused by RTC cleanup
x86/timers/apic: Inform TSC deadline clockevent device about recalibration
x86/timers/apic: Fix imprecise timer interrupts by eliminating TSC clockevents frequency roundoff error
timers: Fix get_next_timer_interrupt() computation
clocksource/arm_arch_timer: Force per-CPU interrupt to be level-triggered
Thomas Garnier [Thu, 11 Aug 2016 21:49:29 +0000 (14:49 -0700)]
PM / hibernate: Restore processor state before using per-CPU variables
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume) Reported-and-tested-by: Borislav Petkov <bp@suse.de> Reported-by: Jiri Kosina <jikos@kernel.org> Tested-by: Rafael J. Wysocki <rafael@kernel.org> Tested-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Garnier <thgarnie@google.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 12 Aug 2016 20:21:18 +0000 (13:21 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus two uncore-PMU fixes, an uprobes fix, a
perf-cgroups fix and an AUX events fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Add enable_box for client MSR uncore
perf/x86/intel/uncore: Fix uncore num_counters
uprobes/x86: Fix RIP-relative handling of EVEX-encoded instructions
perf/core: Set cgroup in CPU contexts for new cgroup events
perf/core: Fix sideband list-iteration vs. event ordering NULL pointer deference crash
perf probe ppc64le: Fix probe location when using DWARF
perf probe: Add function to post process kernel trace events
tools: Sync cpufeatures headers with the kernel
toops: Sync tools/include/uapi/linux/bpf.h with the kernel
tools: Sync cpufeatures.h and vmx.h with the kernel
perf probe: Support signedness casting
perf stat: Avoid skew when reading events
perf probe: Fix module name matching
perf probe: Adjust map->reloc offset when finding kernel symbol from map
perf hists: Trim libtraceevent trace_seq buffers
perf script: Add 'bpf-output' field to usage message
Jeff Layton [Thu, 11 Aug 2016 14:37:39 +0000 (10:37 -0400)]
nfsd: don't return an unhashed lock stateid after taking mutex
nfsd4_lock will take the st_mutex before working with the stateid it
gets, but between the time when we drop the cl_lock and take the mutex,
the stateid could become unhashed (a'la FREE_STATEID). If that happens
the lock stateid returned to the client will be forgotten.
Fix this by first moving the st_mutex acquisition into
lookup_or_create_lock_state. Then, have it check to see if the lock
stateid is still hashed after taking the mutex. If it's not, then put
the stateid and try the find/create again.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com> Cc: stable@vger.kernel.org # feb9dad5 nfsd: Always lock state exclusively. Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Linus Torvalds [Fri, 12 Aug 2016 19:46:37 +0000 (12:46 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Misc fixes: lockstat fix, futex fix on !MMU systems, big endian fix
for qrwlocks and a race fix for pvqspinlocks"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix a bug in qstat_read()
locking/pvqspinlock: Fix double hash race
locking/qrwlock: Fix write unlock bug on big endian systems
futex: Assume all mappings are private on !MMU systems
Linus Torvalds [Fri, 12 Aug 2016 19:39:02 +0000 (12:39 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"A fix for EFI capsules and an SGI UV platform fix"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/capsule: Allocate whole capsule into virtual memory
x86/platform/uv: Skip UV runtime services mapping in the efi_runtime_disabled case
Linus Torvalds [Fri, 12 Aug 2016 19:32:24 +0000 (12:32 -0700)]
Merge tag 'nfs-for-4.8-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Stable patch from Olga to fix RPCSEC_GSS upcalls when the same user
needs multiple different security services (e.g. krb5i and krb5p).
- Stable patch to fix a regression introduced by the use of
SO_REUSEPORT, and that prevented the use of multiple different NFS
versions to the same server.
- TCP socket reconnection timer fixes.
- Patch from Neil to disable the use of IPv6 temporary addresses"
* tag 'nfs-for-4.8-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Cap the transport reconnection timer at 1/2 lease period
NFSv4: Cleanup the setting of the nfs4 lease period
SUNRPC: Limit the reconnect backoff timer to the max RPC message timeout
SUNRPC: Fix reconnection timeouts
NFSv4.2: LAYOUTSTATS may return NFS4ERR_ADMIN/DELEG_REVOKED
SUNRPC: disable the use of IPv6 temporary addresses.
SUNRPC: allow for upcalls for same uid but different gss service
SUNRPC: Fix up socket autodisconnect
SUNRPC: Handle EADDRNOTAVAIL on connection failures
Linus Torvalds [Fri, 12 Aug 2016 19:28:23 +0000 (12:28 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Fix for the nd_blk (NVDIMM Block Window Aperture) driver.
A spec clarification requires the driver to mask off reserved bits in
status register. This is tagged for -stable back to the v4.2 kernel.
- Fix for a kernel crash in the nvdimm unit tests when module loading
is interrupted with SIGTERM. Tagged for -stable since validation
efforts external to Intel use the unit tests for qualifying
backports.
- Add a new 'size' sysfs attribute for the BTT (NVDIMM Block
Translation Table) driver to make it symmetric with the other
namespace personality drivers (PFN and DAX) that provide a size
attribute for indicating how much namespace capacity is lost to
metadata.
The BTT change arrived at the start of the merge window and has
appeared in a -next release. It can technically wait for 4.9, but it
is small, fixes asymmetry in the libnvdimm-sysfs interface, and
something I would have squeezed into the v4.8 pull request had it
arrived a few days earlier.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: fix SIGTERM vs hotplug crash
nvdimm, btt: add a size attribute for BTTs
libnvdimm, nd_blk: mask off reserved status bits
Linus Torvalds [Fri, 12 Aug 2016 19:26:59 +0000 (12:26 -0700)]
Merge tag 'sound-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A regression fix of HD-audio runtime PM and two USB quirks"
* tag 'sound-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Manage power well properly for resume
ALSA: usb-audio: Add quirk for ELP HD USB Camera
ALSA: usb-audio: Add a sample rate quirk for Creative Live! Cam Socialize HD (VF0610)
projects / linux-beck.git / log