Olof Johansson [Wed, 5 Aug 2015 08:45:45 +0000 (10:45 +0200)]
Merge tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Qualcomm ARM Based Device Tree Updates for v4.3
* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC
* tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm:
ARM: dts: qs600: Add real regulators to sdcc
ARM: dts: ifc6410: add real regulators for sdcc nodes.
ARM: dts: apq8064: remove temporary fixed regulator for mmc
ARM: dts: apq8064: fix missing gsbi cell-index
ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux
ARM: dts: apq8064: add pm8921 mpp support
ARM: dts: apq8064: Add pm8921 mfd and its gpio node
ARM: dts: msm8974: Add smem reservation and node
ARM: dts: msm8974: Add tcsr mutex node
ARM: dts: qcom: Add ks8851 node for wired ethernet
ARM: dts: qcom: Add MSM8960 CDP RPM regulators
ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
ARM: dts: qcom: Replace gpio node with pinctrl node
ARM: dts: qcom: Replace gpio node with pinctrl node
Olof Johansson [Wed, 5 Aug 2015 08:39:05 +0000 (10:39 +0200)]
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
First batch of DT changes for 4.3:
- some fixes on sama5d4 ADC definition
- adding Image Sensor Interface (aka ISI) on at91sam9m10g45ek board
- update rst controller compatible string on sama5 machines
- new sama5d2 DT definition and its reference board:
the sama5d2 Xplained. Minimal configuration for now.
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: add minimal sama5d2 Xplained board
ARM: at91/dt: add basic dtsi for sama5d2 SoC
ARM: at91/dt: sama5: update rstc to correct compatible string
ARM: at91/dt: add isi & ov2640 dt nodes for at91sam9m10g45ek board
ARM: at91/dt: sama5d4: move ADC pinctrl to board device trees
ARM: at91/dt: sama5d4: fix external trigger property
Nicolas Ferre [Thu, 18 Jun 2015 12:55:03 +0000 (14:55 +0200)]
ARM: at91/dt: add minimal sama5d2 Xplained board
Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the
peripherals is setup to allow booting.
IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and
uart/usart peripheral nodes are added.
ARM: at91/dt: sama5: update rstc to correct compatible string
They'll use "atmel,sama5d3-rstc" for reset function.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add the old compatible string as a fallback] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Olof Johansson [Tue, 28 Jul 2015 16:25:39 +0000 (18:25 +0200)]
Merge tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.3
- Update clocking for DTS nodes
- Add DTS board file for Terasic DE0 Atlas board
- Use stdout-patch for chosen node
- Enable prefetch-data and prefetch-instr
* tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clk
ARM: socfpga: dts: add missing clock gates to socfpga.dtsi
ARM: socfpga: dts: Fix gpio dts entry for the correct clock
ARM: socfpga: dts: Correct the parent clock for l3_sp_clk and dbg_clk
ARM: dts: socfpga: Add support of Terasic DE0 Atlas board
ARM: dts: socfpga: use stdout-path for chosen node
ARM: dts: socfpga: enable the data and instruction prefetch for the l2 cache
The DT nodes in uniphier-pinctrl.dtsi provide the default pinctrl
settings that would be suitable for most boards. You can still
override them in your board DTS file if necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 27 Jul 2015 12:48:07 +0000 (14:48 +0200)]
Merge tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
omap dts changes for minimal dm814x support for v4.3 merge window.
These changes make dm814x boot and adds minimal board support for
dm814x-evm and hp t410.
Note that to boot these depend on omap-for-v4.3/soc-signed branch,
but as dm814x support is currently broken, these can be merged
separately with the other dts changes.
* tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Add custom abort handler for t410
ARM: dts: Add minimal support for HP T410
ARM: dts: Add minimal dts support for dm8148-evm
ARM: dts: Add minimal clocks for dm814x
ARM: dts: Add minimal dm814x support
Olof Johansson [Mon, 27 Jul 2015 12:28:23 +0000 (14:28 +0200)]
Merge tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.3
* Add Audio MIX and CTU support to r8a779[01] SoCs
* Correct IRQ sense for adv7511 on lager board
* Add sound label to koelsch and lager boards
* Add IIC support to emev2 SoC
* tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Add Audio MIX support on DTSI
ARM: shmobile: r8a7791: Add Audio CTU support on DTSI
ARM: shmobile: r8a7790: Add Audio MIX support on DTSI
ARM: shmobile: r8a7790: Add Audio CTU support on DTSI
ARM: shmobile: lager: Fix adv7511 IRQ sensing
ARM: shmobile: koelsch: add sound label on DTS
ARM: shmobile: lager: add sound label on DTS
ARM: shmobile: emev2: kzm9d: enable IIC busses
ARM: shmobile: emev2: add IIC cores to dtsi
Olof Johansson [Mon, 27 Jul 2015 12:26:03 +0000 (14:26 +0200)]
Merge tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt
STM32 DT updates for v4.3, round 1.
Highlights:
-----------
- Add RCC clocks support to STM32F429
- Add STM32429i-EVAL board support
- Use stdout-path instead of linux,stdout-path in Disco board
* tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
ARM: dts: Use stdout-path in STM32F429 Discovery board
ARM: dts: Add STM32429i-EVAL board support
ARM: dts: stm32f429: Adopt STM32F4 clock driver
Olof Johansson [Mon, 27 Jul 2015 12:23:46 +0000 (14:23 +0200)]
Merge tag 'sti-dt-for-v4.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt
STi DT update for v4.3, round 1.
Highlights:
-----------
- Add pinctrl configurations for transport stream channels
- Add cpu-release-addr properties to STiH407 and STiH418
- Add PWM regulator support so STIH407 family
- Add BDISP node to STiH407
Add dts file to support Buffalo Linkstation LS-WTGL,
which is marvell orion5x based 2-bay 3.5" HDD NAS.
Product info:
- (JPN) http://buffalo.jp/products/catalog/storage/ls-wtgl_r1/
- (ENG) http://www.buffalotech.com/support-and-downloads/download/LinkStation_Pro_Duo_Manual_web.pdf
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Stephen Boyd [Tue, 16 Jun 2015 20:31:15 +0000 (13:31 -0700)]
ARM: dts: qcom: Add ks8851 node for wired ethernet
The micrel ks8851 device is present on MSM8960 CDP boards. It is
connected to two regulators, one controlled via a gpio and
another controlled via the RPM. Add the gsbi, spi, gpio
regulator, and micrel ks8851 nodes so that ethernet works
properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
Olof Johansson [Wed, 22 Jul 2015 23:25:04 +0000 (16:25 -0700)]
Merge tag 'omap-for-v4.3/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.3, part2" from Tony Lindgren:
More omap dts changes for v4.3 merge window:
- Add missing devices for pandora. Note that we're adding wl1251
WLAN and LCD backlight support for now using legacy pdata as that
allows us to drop the legacy board file for pandora in another
series of patches
- Enable power button support for omap5-uevm
- Add aliases for am437x UARTs
- Add support for phyCORE phyBOARD-WEGA-AM335x rdk and
phyCORE-AM335x SoM
- Use u16 values for tsc2046 on omap3-lilly
* tag 'omap-for-v4.3/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap3-pandora: add wifi support
ARM: OMAP2+: omap3-pandora: add backlight support
ARM: dts: omap3-pandora: add support for usb host and 32k buffer
ARM: dts: omap3-pandora: miscellaneous corrections
ARM: dts: omap5-uevm: Add Palmas power button support
ARM: dts: am437x: add aliases for all UART instances
ARM: dts: Add phyBOARD-WEGA-AM335x rdk
ARM: dts: Add support for phyCORE-AM335x SoM
ARM: dts: omap3: correct the format of u16 values for tsc2046 node
To enable SMP when booting via u-boot we need to specify the
newly implemented cpu-release-addr DT property for cores 2 & 3.
Cores 0 & 1 are inherited from stih407-family.dtsi.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
To enable SMP when booting via u-boot we need to specify the
newly implemented cpu-release-addr DT property.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Wed, 10 Jun 2015 14:04:00 +0000 (16:04 +0200)]
ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration
tsin5 can only be configured for serial data transfer. However
depending on board design, two alternate tsin5 pin configurations
are available, both in pin-controller-front0.
pinctrl_tsin5_serial_alt1 is brought out on B2120 reference
design as TSD on NIMB slot of the B2004A daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Wed, 10 Jun 2015 14:04:00 +0000 (16:04 +0200)]
ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration
tsin4 can only be configured for serial data transfer. However
depending on board design, two alternate pin configurations
are available. One in pin-controller-front0 and the other in
pin-controller-front1.
pinctrl_tsin4_serial_alt3 is brought out on B2120 reference
design as TSC on NIMA slot of the B2004A daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Wed, 10 Jun 2015 14:03:00 +0000 (16:03 +0200)]
ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration
tsin0 and be configured as either serial or parallel. This patch
adds the pinctrl config for both possiblities. On B2120 reference
design tsin0 is brought out as TSA on the NIMA slot of the B2004A
daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: dts: socfpga: Add support of Terasic DE0 Atlas board
The Terasic DE0 Atlas board is also known as the DE0-Nano board.
This patch adds the DTS board file for the DE0-Nano Sockit board, and not
the DE0 Nano "Development Board".
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Updated skew settings for the gmac1 node as this board is using the
KSZ9031 PHY instead of the 9021 PHY.
v2: use stdpath-out for console and remove comment regarding u-boot ethaddr
Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
- add pandora specific compatible name
- fix mmc2 card detect polarity
- fix mmc1 and mmc2 write protect polarity
- disable write protect pins because of production issue and add an
explanation why they are disabled
- fix NAND partition name to reflect the correct address
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.
Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.
WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
phyCORE-AM335x is a SoM (System on Module) containing
a AM335x SOC. The module can be connected to different
carrier boards.
Some hardware parts are configurable on the phyCORE-AM335x.
So they are disabled on default in this som dtsi file.
They will be enabled in the board dts files, when populated.
* RAM up to 1GiB
* PMIC
* NAND flash up to 1GiB
* Eth PHY on SOM: 1x RMII
* SPI NOR flash 8MiB (optional)
* i2c RTC (optional)
* i2c EEPROM 4kiB (optional)
Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3: correct the format of u16 values for tsc2046 node
In tsc2046 touch driver, the values such as ti,x-min is defined as a u16
value. the driver use API of_property_read_u16() read the value. For these
u16 value, the dts entry should be like:
property = /bits/ 16 <0x5000>;
This describes the property as a u16 value.
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Fri, 17 Jul 2015 17:37:26 +0000 (10:37 -0700)]
Merge tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts changes for 4.3, part1" from Heiko Stuebner:
This adds the board for the Netxeon R89 used in different TV-boxes and
the initial support for two Chromebooks from the veyron family.
Additionally a non-critical fix for the watchdog irq on rk3288, addition
of the gmac reset line, a ramp delay for the cpu regulator on the firefly
board and cpu affinity for the arm-pmu spi irqs.
* tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288 arm-pmu irq affinity
dt-bindings: document rk3368 R88 board from Rockchip
ARM: dts: rockchip: add missing device_type = "memory" to boards
ARM: dts: rockchip: add veyron-pinky board
ARM: dts: rockchip: add veyron-jerry board
ARM: dts: rockchip: add shared rk3288-veyron files
ARM: dts: Add sbs-battery dts fragment used by chromebooks
ARM: dts: rockchip: add Netxeon R89 board
dt-bindings: add vendor prefix for Netxeon Technology
ARM: dts: rockchip: fix rk3288 watchdog irq
ARM: dts: rockchip: Add ramp delay for vdd_cpu in firefly board dts
ARM: dts: rockchip: Add STMMAC reset signal in GMAC interface for rk3288
Olof Johansson [Fri, 17 Jul 2015 17:16:36 +0000 (10:16 -0700)]
Merge tag 'arm-soc/for-4.3/dts' of http://github.com/broadcom/stblinux into next/dt
Merge "Broadcom Device Tree changes for 4.3 (part 1)" from Florian Fainelli:
This pull request contains two changes:
- Ray adds the relevant clocks device tree nodes for Cygnus SoCs
- Rafal enables UART0 on BCM5301X routers where it has been verified to work
correctly
* tag 'arm-soc/for-4.3/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Enable UART0 on tested devices
ARM: dts: enable clock support for Broadcom Cygnus
Olof Johansson [Fri, 17 Jul 2015 17:08:17 +0000 (10:08 -0700)]
Merge tag 'mvebu-dt-4.3-1' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: dt changes for v4.3" from Gregory Clement:
mvebu dt changes for v4.3 (part #1)
- Update Armada 388 GP description
- Add Buffalo Linkstation LS-WXL and LS-WSXL
- Fine-tune the L2 configuration for cortex A9 based SoC
- Update XOR definition for Armada 38x and 39x SoC
* tag 'mvebu-dt-4.3-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update EEPROM description of Armada 388 GP
ARM: mvebu: fix description of pwr-sata0 regulator on Armada 388 GP
ARM: dts: add buffalo linkstation ls-wvl/vl
ARM: dts: add buffalo linkstation ls-wxl/wsxl
ARM: mvebu: use DT properties to fine-tune the L2 configuration
ARM: mvebu: use armada-380-xor on Armada 38x and 39x
Olof Johansson [Fri, 17 Jul 2015 16:53:02 +0000 (09:53 -0700)]
Merge branch 'lpc18xx_43xx_dts_4.3' of https://github.com/manabian/linux-lpc into next/dt
Merge "LPC18xx DTS changes for 4.3" from Joachim Eastwood:
This patch set adds DT nodes for all the drivers that went upstream in
4.2 and should represent the bulk of DTS changes for 4.3. All nodes
added are documented and some of patches carries a ack from subsystem
maintainer. It also features updates to the EA4357 dev- kit and a new
board from Ezequiel Garcia.
Note that there might be one more batch of DTS changes for 4.3 if any
new drivers goes upstream and also some changes for the Hitex eval board
might come.
While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.
Signed-off-by: Alexandru M Stan <amstan@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org>
This adds the shared devicetree files for the Veyron device family.
They are split, as not all veyron devices are chromebooks and
not all contain a sd-card slot.
Signed-off-by: Alexandru M Stan <amstan@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org>
Olof Johansson [Wed, 15 Jul 2015 14:17:14 +0000 (10:17 -0400)]
Merge tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.3, part 1" from Tony Lindgren:
Omap dts changes for v4.3 merge window. There are also related
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
* tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (32 commits)
ARM: dts: am335x-evm: Switch using simple-audio-card for audio support
ARM: dts: am335x-evm: Add sleep pin settings for mcasp1
ARM: dts: am335x-evm: Rename pinctrl section for McASP1
ARM: dts: am335x-evm: Fix mcasp1 node's indentation
ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio support
ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1
ARM: dts: am335x-evmsk: Fix mcasp1 node's indentation
ARM: dts: am437x-gp-evm: Enable analog audio via simple-card
ARM: dts: am437x-gp-evm: McASP1 node for audio support
ARM: dts: am437x-gp-evm: Add node for tlv320aic3106 audio codec
ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am43xx-epos-evm: Enable analog audio via simple-card
ARM: dts: am43xx-epos-evm: Add node for tlv320aic3111 audio codec
ARM: dts: am43xx-epos-evm: McASP1 node for audio support
ARM: dts: am43xx-epos-evm: Add regulator for VBAT and DCDC4 of tps65218
ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
ARM: dts: am437x-sk-evm: Add sleep pin settings for mcasp1
ARM: omap2plus_defconfig: Enable audio related config options
...
projects / linux-beck.git / log