The tuner-core subdev requires that the type field of v4l2_tuner is
filled in correctly. This is done in v4l2-ioctl.c, but pvrusb2 doesn't
use that yet, so we have to do it manually based on whether the current
input is radio or not.
Tested with my pvrusb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both s_std and s_tuner are broken because set_mode_freq is called before the
new std (for s_std) and audmode (for s_tuner) are set.
This patch splits set_mode_freq in a set_mode and a set_freq and in s_std/s_tuner
first calls set_mode, and if that returns 0 (i.e. the mode is supported)
then they set t->std/t->audmode and call set_freq.
This fixes a bug where changing std or audmode would actually change it to
the previous value.
Discovered while testing analog TV standards for cx18 with a tda18271 tuner.
The subdevs are supposed to receive a valid tuner type for the g_frequency
and g/s_tuner subdev ops. Some drivers do this, others don't. So prefill
this in v4l2-ioctl.c based on whether the device node from which this is
called is a radio node or not.
The spec does not require applications to fill in the type, and if they
leave it at 0 then the 'check_mode' call in tuner-core.c will return
an error and the ioctl does nothing.
as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens. https://bugzilla.kernel.org/show_bug.cgi?id=36622
Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The file mfp-pxa2xx.c defines a macro, PGSR(), which translates a gpio
bank number to a PGSR register address. The function pxa2xx_mfp_suspend()
erroneously passed in a gpio number instead of a gpio bank number.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original pair of <0x01db, 208000000> is invalid. Correct it to
the valid value.
The 6th bit of the NFC APMU register indicates NFC works whether
at 156Mhz or 78Mhz. So 0x19b indicates NFC works at 156Mhz, and
0x1db indicates it works at 78Mhz.
Signed-off-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
armpmu_enable can be called in situations where no events are present
(for example, from the event rotation tick after a profiled task has
exited). In this case, we currently start the PMU anyway which may
leave it active inevitably without any events being monitored.
This patch adds a simple check to the enabling code so that we avoid
starting the PMU when no events are present.
Reported-by: Ashwin Chaugle <ashwinc@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin DMA controller can report one frame beyond the end of the
buffer in the wraparound case but ALSA requires that the pointer always
be in the buffer. Do the wraparound to handle this. A similar bug is
likely to apply to the other Blackfin PCM drivers but the code is less
obvious to inspection and I don't have a user to test.
Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Some PMBus devices return no error when reading fan speed registers, but don't
really support fans. Strengthen fan detection by also checking if fan
configuration registers exist.
Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.
Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.
Fix problem by accepting only the known LM95241 chip ID.
When deciding if kswapd is sleeping prematurely, the classzone is taken
into account but this is different to what balance_pgdat() and the
allocator are doing. Specifically, the DMA zone will be checked based on
the classzone used when waking kswapd which could be for a GFP_KERNEL or
GFP_HIGHMEM request. The lowmem reserve limit kicks in, the watermark is
not met and kswapd thinks it's sleeping prematurely keeping kswapd awake in
error.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Pádraig Brady <P@draigBrady.com> Tested-by: Pádraig Brady <P@draigBrady.com> Tested-by: Andrew Lutomirski <luto@mit.edu> Acked-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remap_pfn_range() means map physical address pfn<<PAGE_SHIFT to user addr.
For nommu arch it's implemented by vma->vm_start = pfn << PAGE_SHIFT which
is wrong acroding the original meaning of this function. And some driver
developer using remap_pfn_range() with correct parameter will get
unexpected result because vm_start is changed. It should be implementd
like addr = pfn << PAGE_SHIFT but which is meanless on nommu arch, this
patch just make it simply return.
Parameter name and setting of vma->vm_flags also be fixed.
Signed-off-by: Bob Liu <lliubbo@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: David Howells <dhowells@redhat.com> Acked-by: Greg Ungerer <gerg@uclinux.org> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Bob Liu <lliubbo@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour. Unfortunately, if the highest zone is small, a
problem occurs.
This seems to happen most with recent sandybridge laptops but it's
probably a co-incidence as some of these laptops just happen to have a
small Normal zone. The reproduction case is almost always during copying
large files that kswapd pegs at 100% CPU until the file is deleted or
cache is dropped.
The problem is mostly down to sleeping_prematurely() keeping kswapd awake
when the highest zone is small and unreclaimable and compounded by the
fact we shrink slabs even when not shrinking zones causing a lot of time
to be spent in shrinkers and a lot of memory to be reclaimed.
Patch 1 corrects sleeping_prematurely to check the zones matching
the classzone_idx instead of all zones.
Patch 2 avoids shrinking slab when we are not shrinking a zone.
Patch 3 notes that sleeping_prematurely is checking lower zones against
a high classzone which is not what allocators or balance_pgdat()
is doing leading to an artifical belief that kswapd should be
still awake.
Patch 4 notes that when balance_pgdat() gives up on a high zone that the
decision is not communicated to sleeping_prematurely()
This problem affects 2.6.38.8 for certain and is expected to affect 2.6.39
and 3.0-rc4 as well. If accepted, they need to go to -stable to be picked
up by distros and this series is against 3.0-rc4. I've cc'd people that
reported similar problems recently to see if they still suffer from the
problem and if this fixes it.
This patch: correct the check for kswapd sleeping in sleeping_prematurely()
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour.
A problem occurs if the highest zone is small. balance_pgdat() only
considers unreclaimable zones when priority is DEF_PRIORITY but
sleeping_prematurely considers all zones. It's possible for this sequence
to occur
1. kswapd wakes up and enters balance_pgdat()
2. At DEF_PRIORITY, marks highest zone unreclaimable
3. At DEF_PRIORITY-1, ignores highest zone setting end_zone
4. At DEF_PRIORITY-1, calls shrink_slab freeing memory from
highest zone, clearing all_unreclaimable. Highest zone
is still unbalanced
5. kswapd returns and calls sleeping_prematurely
6. sleeping_prematurely looks at *all* zones, not just the ones
being considered by balance_pgdat. The highest small zone
has all_unreclaimable cleared but the zone is not
balanced. all_zones_ok is false so kswapd stays awake
This patch corrects the behaviour of sleeping_prematurely to check the
zones balance_pgdat() checked.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Pádraig Brady <P@draigBrady.com> Tested-by: Pádraig Brady <P@draigBrady.com> Tested-by: Andrew Lutomirski <luto@mit.edu> Acked-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit e534c5b831c8b8e9f5edee5c8a37753c808b80dc (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Quote from Patric Mc Hardy
"This looks like nfnetlink.c excited and destroyed the nfnl socket, but
ip_vs was still holding a reference to a conntrack. When the conntrack
got destroyed it created a ctnetlink event, causing an oops in
netlink_has_listeners when trying to use the destroyed nfnetlink
socket."
If nf_conntrack_netlink is loaded before ip_vs this is not a problem.
This patch simply avoids calling ip_vs_conn_drop_conntrack()
when netns is dying as suggested by Julian.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 128-bit multiply in pvclock.h was missing an output constraint for
EDX which caused a register corruption to appear. Thanks to Ulrich for
diagnosing the EDX corruption and Avi for providing this fix.
Alex Williamson [Thu, 23 Jun 2011 16:35:22 +0000 (13:35 -0300)]
Revert "KVM: Save/restore state of assigned PCI device"
This reverts ed78661f2614d3c9f69c23e280db3bafdabdf5bb as it assumes
the saved PCI state will remain valid for the entire length of time
that it is attached to a guest. This fails when userspace makes use
of the pci-sysfs reset interface, which invalidates the saved device
state, leaving nothing to be restored after the device is reset on
de-assignment. This leaves the device in an unusable state.
3.0.0 will add an interface for KVM to save the PCI state in a
buffer unaffected by other callers of pci_reset_function(), but the
most appropriate stable fix seems to be reverting this change since
the original assumption about the device saved state persisting is
incorrect.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We may write 4 byte too much when we reinitialize the anti replay
window in the replay advance functions. This patch fixes this by
adjusting the last index of the initialization loop.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4af429d29b341bb1735f04c2fb960178ed5d52e7 (vlan: lockless
transmit path) have a typo in vlan_dev_hard_start_xmit(), using
u64_stats_update_begin() to end the stat update, it should be
u64_stats_update_end().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid creating input routes with ip_route_me_harder.
It does not work for locally generated packets. Instead,
restrict sockets to provide valid saddr for output route (or
unicast saddr for transparent proxy). For other traffic
allow saddr to be unicast or local but if callers forget
to check saddr type use 0 for the output route.
The resulting handling should be:
- REJECT TCP:
- in INPUT we can provide addr_type = RTN_LOCAL but
better allow rejecting traffic delivered with
local route (no IP address => use RTN_UNSPEC to
allow also RTN_UNICAST).
- FORWARD: RTN_UNSPEC => allow RTN_LOCAL/RTN_UNICAST
saddr, add fix to ignore RTN_BROADCAST and RTN_MULTICAST
- OUTPUT: RTN_UNSPEC
- NAT, mangle, ip_queue, nf_ip_reroute: RTN_UNSPEC in LOCAL_OUT
- IPVS:
- use RTN_LOCAL in LOCAL_OUT and FORWARD after SNAT
to restrict saddr to be local
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Knut Tidemann found that first packet of a multicast flow was not
correctly received, and bisected the regression to commit b23dd4fe42b4
(Make output route lookup return rtable directly.)
Special thanks to Knut, who provided a very nice bug report, including
sample programs to demonstrate the bug.
Reported-and-bisectedby: Knut Tidemann <knut.andre.tidemann@jotron.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1476) fixes a regression introduced by fccf4e86200b8f5edd9a65da26f150e32ba79808 (USB: Free bandwidth when
usb_disable_device is called). usb_disconnect() grabs the
bandwidth_mutex before calling usb_disable_device(), which calls down
indirectly to usb_set_interface(), which tries to acquire the
bandwidth_mutex.
The fix causes usb_set_interface() to return early when it is called
for an interface that has already been unregistered, which is what
happens in usb_disable_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1465) continues implementation of the policy that errors
during suspend or hibernation should not prevent the system from going
to sleep.
In this case, failure to turn on the Suspend feature for a hub port
shouldn't be reported as an error. There are situations where this
does actually occur (such as when the device plugged into that port
was disconnected in the recent past), and it turns out to be harmless.
There's no reason for it to prevent a system sleep.
Also, don't allow the hub driver to fail a system suspend if the
downstream ports aren't all suspended. This is also harmless (and
should never happen, given the change mentioned above); printing a
warning message in the kernel log is all we really need to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1464) implements the recommended policy that most errors
during suspend or hibernation should not prevent the system from going
to sleep. In particular, failure to suspend a USB driver or a USB
device should not prevent the sleep from succeeding:
Failure to suspend a device won't matter, because the device will
automatically go into suspend mode when the USB bus stops carrying
packets. (This might be less true for USB-3.0 devices, but let's not
worry about them now.)
Failure of a driver to suspend might lead to trouble later on when the
system wakes up, but it isn't sufficient reason to prevent the system
from going to sleep.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the NLM daemon is killed on the NFS server, we can currently end up
hanging forever on an 'unlock' request, instead of aborting. Basically,
if the rpcbind request fails, or the server keeps returning garbage, we
really want to quit instead of retrying.
Secondary CPU bringup typically calls calibrate_delay() during its
initialization. However, calibrate_delay() modifies a global variable
(loops_per_jiffy) used for udelay() and __delay().
A side effect of 71c696b1 ("calibrate: extract fall-back calculation
into own helper") introduced in the 2.6.39 merge window means that we
end up with a substantial period where loops_per_jiffy is zero. This
causes the spinlock debugging code to malfunction:
u64 loops = loops_per_jiffy * HZ;
for (;;) {
for (i = 0; i < loops; i++) {
if (arch_spin_trylock(&lock->raw_lock))
return;
__delay(1);
}
...
}
by never calling arch_spin_trylock() - resulting in the CPU locking
up in an infinite loop inside __spin_lock_debug().
Work around this by only writing to loops_per_jiffy only once we have
completed all the calibration decisions.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
--
Better solutions (such as omitting the calibration for secondary CPUs,
or arranging for calibrate_delay() to return the LPJ value and leave
it to the caller to decide where to store it) are a possibility, but
would be much more invasive into each architecture.
I think this is the best solution for -rc and stable, but it should be
revisited for the next merge window.
Currently a single process may register exit handlers unlimited times.
It may lead to a bloated listeners chain and very slow process
terminations.
Eg after 10KK sent TASKSTATS_CMD_ATTR_REGISTER_CPUMASKs ~300 Mb of
kernel memory is stolen for the handlers chain and "time id" shows 2-7
seconds instead of normal 0.003. It makes it possible to exhaust all
kernel memory and to eat much of CPU time by triggerring numerous exits
on a single CPU.
The patch limits the number of times a single process may register
itself on a single CPU to one.
One little issue is kept unfixed - as taskstats_exit() is called before
exit_files() in do_exit(), the orphaned listener entry (if it was not
explicitly deregistered) is kept until the next someone's exit() and
implicit deregistration in send_cpu_listeners(). So, if a process
registered itself as a listener exits and the next spawned process gets
the same pid, it would inherit taskstats attributes.
We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done. Because of this we never call lkdtm_do_action(). This patch just
adds a spinlock to protect count.
When an interface changes type to a P2P type,
iwlagn will erroneously set vif->type to the
P2P type and not the reduced/split type. Fix
this by keeping "newtype" in another variable
for the assignment to vif->type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The message hints that disc_data_lock is aquired with softirqs disabled,
but does not itself disable softirqs, which can in rare circumstances
lead to a deadlock.
The same problem is present in the 6pack driver, this patch fixes both
by using write_lock_bh instead of write_lock.
Reported-by: Bernard F6BVP <f6bvp@free.fr> Tested-by: Bernard F6BVP <f6bvp@free.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ralf Baechle<ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an FS-Cache helper to bulk uncache pages on an inode. This will
only work for the circumstance where the pages in the cache correspond
1:1 with the pages attached to an inode's page cache.
This is required for CIFS and NFS: When disabling inode cookie, we were
returning the cookie and setting cifsi->fscache to NULL but failed to
invalidate any previously mapped pages. This resulted in "Bad page
state" errors and manifested in other kind of errors when running
fsstress. Fix it by uncaching mapped pages when we disable the inode
cookie.
This patch should fix the following oops and "Bad page state" errors
seen during fsstress testing.
locks_alloc_lock() assumed that the allocated struct file_lock is
already initialized to zero members. This is only true for the first
allocation of the structure, after reuse some of the members will have
random values.
This will for example result in passing random fl_start values to
userspace in fuse for FL_FLOCK locks, which is an information leak at
best.
Fix by reinitializing those members which may be non-zero after freeing.
This reverts 737a3bb9416ce2a7c7a4 ("Driver core: move platform device
creation helpers to .init.text (if MODULE=n)"). That patch assumed that
platform_device_register_resndata() is only ever called from __init code
but that isn't true in the case ioctl->drm_ioctl->radeon_cp_init().
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.
We should check if the device is faulty before considering it to be a
spare. This will avoid trying to start a recovery that cannot
proceed.
This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.
pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default. This is bad.
1. Load I2C bus driver: creates I2C-bus-1
2. Load pca954x driver: creates virtual I2C-bus-101 and I2C-bus-111
3. Load eeprom driver
4. Try to read EEPROM @ 0x50 on I2C-bus-101. The transaction will also bleed
onto I2C-bus-111 because pca954x @ 0x71 channel 0 is connected by default.
Fix: Initialize pca954x to disconnected state in pca954x_probe()
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If construct_alloc_key() returns an error, it shouldn't pass out through
the normal path as the key_serial() called by the kleave() statement
will oops when it gets an error code in the pointer:
There is a bug in free_unnecessary_pages() that causes it to
attempt to free too many pages in some cases, which triggers the
BUG_ON() in memory_bm_clear_bit() for copy_bm. Namely, if
count_data_pages() is initially greater than alloc_normal, we get
to_free_normal equal to 0 and "save" greater from 0. In that case,
if the sum of "save" and count_highmem_pages() is greater than
alloc_highmem, we subtract a positive number from to_free_normal.
Hence, since to_free_normal was 0 before the subtraction and is
an unsigned int, the result is converted to a huge positive number
that is used as the number of pages to free.
Fix this bug by checking if to_free_normal is actually greater
than or equal to the number we're going to subtract from it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PM core doesn't handle suspend failures correctly when it comes to
asynchronously suspended devices. These devices are moved onto the
dpm_suspended_list as soon as the corresponding async thread is
started up, and they remain on the list even if they fail to suspend
or the sleep transition is cancelled before they get suspended. As a
result, when the PM core unwinds the transition, it tries to resume
the devices even though they were never suspended.
This patch (as1474) fixes the problem by adding a new "is_suspended"
flag to dev_pm_info. Devices are resumed only if the flag is set.
[rjw:
* Moved the dev->power.is_suspended check into device_resume(),
because we need to complete dev->power.completion and clear
dev->power.is_prepared too for devices whose
dev->power.is_suspended flags are unset.
* Fixed __device_suspend() to avoid setting dev->power.is_suspended
if async_error is different from zero.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit e8665002477f0278f84f898145b1f141ba26ee26
(PM: Allow pm_runtime_suspend() to succeed during system suspend) it
is possible that a device resumed by the pm_runtime_resume(dev) in
pci_pm_prepare() will be suspended immediately from a work item,
timer function or otherwise, defeating the very purpose of calling
pm_runtime_resume(dev) from there. To prevent that from happening
it is necessary to increment the runtime PM usage counter of the
device by replacing pm_runtime_resume() with pm_runtime_get_sync().
Moreover, the incremented runtime PM usage counter has to be
decremented by the corresponding pci_pm_complete(), via
pm_runtime_put_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
6b4517a791 (block: implement bd_claiming and claiming block)
introduced claiming block to support O_EXCL blkdev opens properly.
bd_start_claiming() looks up the part 0 bdev and starts claiming
block. The function assumed that there is only one part 0 bdev and
always used bdget_disk(disk, 0) to look it up; unfortunately, this
isn't true for some drivers (floppy) which use multiple block devices
to denote different operating parameters for the same physical device.
There can be multiple part 0 bdev's for the same device number.
This incorrect assumption caused the wrong bdev to be used during
claiming leading to unbalanced bd_holders as reported in the following
bug.
https://bugzilla.kernel.org/show_bug.cgi?id=28522
This patch updates bd_start_claiming() such that it uses the bdev
specified as argument if its partno is zero.
Note that this means that different bdev's can be used for the same
device and O_EXCL check can be effectively bypassed. It has always
been broken that way and floppy is fortunately on its way out. Leave
that breakage alone.
Since we are modifying this RCU pointer, we need to hold
the lock protecting it around it.
This fixes a potential reuse and double free of a cfq
io_context structure. The bug has been in CFQ for a long
time, it hit very few people but those it did hit seemed
to see it a lot.
Order of initialization look like this:
...
debugobjects
kmemleak
...(lots of other subsystems)...
workqueues (through early initcall)
...
debugobjects use schedule_work for batch freeing of its data and kmemleak
heavily use debugobjects, so when it comes to freeing and workqueues were
not initialized yet, kernel crashes:
Commit 7ebb9315 (NFS: use secinfo when crossing mountpoints) introduces
a regression when decoding an NFSv4 readdir entry that sets the
rdattr_error field.
By treating the resulting value as if it is a decoding error, the current
code may cause us to skip valid readdir entries.
Commit 28331a46d88459788c8fca72dbb0415cd7f514c9 "Ensure we request the
ordinary fileid when doing readdirplus"
changed the meaning of NFS_ATTR_FATTR_FILEID which used to be set when
FATTR4_WORD1_MOUNTED_ON_FILED was requested.
Allow nfs_fhget to succeed with only a mounted on fileid when crossing
a mountpoint or a referral.
Ask for the fileid of the absent file system if mounted_on_fileid is not
supported.
Thanks to Casey Bodley for pointing out that on a read open we pass 0,
instead of O_RDONLY, to break_lease, with the result that a read open is
treated like a write open for the purposes of lease breaking!
Reported-by: Casey Bodley <cbodley@citi.umich.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the LINK operation breaks a delegation, it returns NFS4ERR_NOENT
(which is not a valid error in rfc 5661) instead of NFS4ERR_DELAY.
the return value of nfsd_break_lease() in nfsd_link() must be
converted from host_err to err
Signed-off-by: Casey Bodley <cbodley@citi.umich.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b0b0c0a26e84 "nfsd: add proc file listing kernel's gss_krb5
enctypes" added an nunnecessary dependency of nfsd on the auth_rpcgss
module.
It's a little ad hoc, but since the only piece of information nfsd needs
from rpcsec_gss_krb5 is a single static string, one solution is just to
share it with an include file.
Reported-by: Michael Guntsche <mike@it-loops.com> Cc: Kevin Coffman <kwc@citi.umich.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Wakko Warner <wakko@animx.eu.org> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it
was uncovered that at least some variants of the ITE8709 need to use pnp
resource 2, rather than 0, for things to function properly. Resource 0
has a length of only 1, and if you try to bypass the pnp_port_len check
and use it anyway (with either a length of 1 or 2), the system in
question's trackpad ceased to function.
The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value
was (amusingly) changed to 0 by way of a patch from ITE themselves, so I
don't know if there may be variants where 0 actually *is* correct, but
at least in this case and in the original lirc_ite8709 driver author's
case, it sure looks like 2 is the right value.
This fix should probably be applied to all stable kernels with the
ite-cir driver, lest we nuke more people's trackpads.
Tested-by: Matthijs van Drunen Acked-by: Juan Jesús García de Soria <skandalfo@gmail.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5
scancodes, so this update makes this keymap actually *have* full
scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box
remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and
PCTV HD Pro 801e (em28xx usb stick).
We were calling schedule_timeout with the rx thread's task state still
at TASK_RUNNING, which it shouldn't be. Make sure we call
set_current_state(TASK_INTERRUPTIBLE) *before* schedule_timeout, and
we're all good here. I believe this problem was mistakenly introduced in
commit 5bd6b0464b68d429bc8a3fe6595d19c39dfc4d95, and I'm not sure how I
missed it before, as I swear I tested the patchset that was included in,
but alas, stuff happens...
Acked-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With hardware that has to use ir_raw_event_store_edge to collect IR
sample durations, we were not doing an event reset unless
IR_MAX_DURATION had passed. That's around 4 seconds. So if someone
presses up, then down, with less than 4 seconds in between, they'd get
the initial up, then up and down upon pressing down.
To fix this, I've lowered the "send a reset event" logic's threshold to
the input device's REP_DELAY (defaults to 500ms), and with an
saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get
*much* better behavior out of the remote now. Special thanks to Devin
for providing the hardware to investigate this issue.
The error handling in mem_online_node() is incorrect: hotadd_new_pgdat()
returns NULL if the new pgdat could not have been allocated and a pointer
to it otherwise.
mem_online_node() should fail if hotadd_new_pgdat() fails, not the
inverse. This fixes an issue when memoryless nodes are not onlined and
their sysfs interface is not registered when their first cpu is brought
up.
The bug was introduced by commit cf23422b9d76 ("cpu/mem hotplug: enable
CPUs online before local memory online") iow v2.6.35.
nfs_update_inode will update isize if there is no queued pages. For pNFS,
layoutcommit is supposed to change file size on server, the same effect as queued
pages. nfs_update_inode may be called when dirty pages are written back (nfsi->npages==0)
but layoutcommit is not sent, and it will change client file size according to server
file size. Then client ends up losing what it just writes back in pNFS path.
So we should skip updating client file size if file needs layoutcommit.
When 1GB hugepages are allocated on a system, free(1) reports less
available memory than what really is installed in the box. Also, if the
total size of hugepages allocated on a system is over half of the total
memory size, CommitLimit becomes a negative number.
The problem is that gigantic hugepages (order > MAX_ORDER) can only be
allocated at boot with bootmem, thus its frames are not accounted to
'totalram_pages'. However, they are accounted to hugetlb_total_pages()
What happens to turn CommitLimit into a negative number is this
calculation, in fs/proc/meminfo.c:
A similar calculation occurs in __vm_enough_memory() in mm/mmap.c.
Also, every vm statistic which depends on 'totalram_pages' will render
confusing values, as if system were 'missing' some part of its memory.
Impact of this bug:
When gigantic hugepages are allocated and sysctl_overcommit_memory ==
OVERCOMMIT_NEVER. In a such situation, __vm_enough_memory() goes through
the mentioned 'allowed' calculation and might end up mistakenly returning
-ENOMEM, thus forcing the system to start reclaiming pages earlier than it
would be ususal, and this could cause detrimental impact to overall
system's performance, depending on the workload.
Besides the aforementioned scenario, I can only think of this causing
annoyances with memory reports from /proc/meminfo and free(1).
[akpm@linux-foundation.org: standardize comment layout] Reported-by: Russ Anderson <rja@sgi.com> Signed-off-by: Rafael Aquini <aquini@linux.com> Acked-by: Russ Anderson <rja@sgi.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Christoph Lameter <cl@linux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b6147490e6aac82 ("mmc: tmio: split core functionality, DMA and
MFD glue") broke handling of the TMIO_MMC_WRPROTECT_DISABLE flag by
the tmio-mmc driver. This patch restores the original behaviour.
In some rare cases, nmis are generated immediately after the nmi
handler of the cpu was started. This causes the counter not to be
enabled. Before enabling the nmi handlers we need to set variable
ctr_running first and make sure its value is written to memory.
Also, the patch makes all existing barriers a memory barrier instead
of a compiler barrier only.
Some BIOSes will reset the Intel MISC_ENABLE MSR (specifically the
XD_DISABLE bit) when resuming from S3, which can interact poorly with ebba638ae723d8a8fc2f7abce5ec18b688b791d7. In 32bit PAE mode, this can
lead to a fault when EFER is restored by the kernel wakeup routines,
due to it setting the NX bit for a CPU that (thanks to the BIOS reset)
now incorrectly thinks it lacks the NX feature. (64bit is not affected
because it uses a common CPU bring-up that specifically handles the
XD_DISABLE bit.)
The need for MISC_ENABLE being restored so early is specific to the S3
resume path. Normally, MISC_ENABLE is saved in save_processor_state(),
but this happens after the resume header is created, so just reproduce
the logic here. (acpi_suspend_lowlevel() creates the header, calls
do_suspend_lowlevel, which calls save_processor_state(), so the saved
processor context isn't available during resume header creation.)
[ hpa: Consider for stable if OK in mainline ]
Signed-off-by: Kees Cook <kees.cook@canonical.com> Link: http://lkml.kernel.org/r/20110707011034.GA8523@outflux.net Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the socket buffer is freed in the completion interrupt, it is not
safe to access it after submitting it to the hardware.
Acked-by: Sachin Sanap <ssanap@marvell.com> Cc: Zhangfei Gao <zgao6@marvell.com> Cc: Philip Rakity <prakity@marvell.com> Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable fast channel change by default on AR2413/AR5413 due to
some bug reports (it still works for me but it's better to be safe).
Add a module parameter "fastchanswitch" in case anyone wants to enable
it and play with it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We would free the proper number of curves, but in the wrong
slots, due to a missing level of indirection through
the pdgain_idx table.
It's simpler just to try to free all four slots, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When opening /dev/snapshot device, snapshot_open() creates memory
bitmaps which are freed in snapshot_release(). But if any of the
callbacks called by pm_notifier_call_chain() returns NOTIFY_BAD, open()
fails, snapshot_release() is never called and bitmaps are not freed.
Next attempt to open /dev/snapshot then triggers BUG_ON() check in
create_basic_memory_bitmaps(). This happens e.g. when vmwatchdog module
is active on s390x.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pages isolated for migration are accounted with the vmstat counters
NR_ISOLATE_[ANON|FILE]. Callers of migrate_pages() are expected to
increment these counters when pages are isolated from the LRU. Once the
pages have been migrated, they are put back on the LRU or freed and the
isolated count is decremented.
Memory failure is not properly accounting for pages it isolates causing
the NR_ISOLATED counters to be negative. On SMP builds, this goes
unnoticed as negative counters are treated as 0 due to expected per-cpu
drift. On UP builds, the counter is treated by too_many_isolated() as a
large value causing processes to enter D state during page reclaim or
compaction. This patch accounts for pages isolated by memory failure
correctly.
appended patch adds support for the new FTDI FT232H chip. This chip is a
single channel version of the dual FT2232H/quad FT4232H, coming with it's
own default PID 0x6014 (FT2232H uses the same PID 0x6010 like FT2232C,
FT4232H has also it's own PID).
The patch was checked on an UM232H module and a terminal program with TX/RX
shorted to that typing in the terminal reproduced the characters.
Tanya ran into an issue when trying to switch a UAS device from the BOT
configuration to the UAS configuration via the bConfigurationValue sysfs
file. Before installing the UAS configuration, set_bConfigurationValue()
calls usb_disable_device(). That function is supposed to remove all host
controller resources associated with that device, but it leaves some state
in the xHCI host controller.
Commit 0791971ba8fbc44e4f476079f856335ed45e6324
usb: allow drivers to use allocated bandwidth until unbound
added a call to usb_disable_device() in usb_set_configuration(), before
the xHCI bandwidth functions were invoked. That commit fixed a bug, but
also introduced a bug that is triggered when a configured device is
switched to a new configuration.
usb_disable_device() goes through all the motions of unbinding the drivers
attached to active interfaces and removing the USB core structures
associated with those interfaces, but it doesn't actually remove the
endpoints from the internal xHCI host controller bandwidth structures.
When usb_disable_device() calls usb_disable_endpoint() with reset_hardware
set to true, the entries in udev->ep_out and udev->ep_in will be set to
NULL. Usually, when the USB core installs a new configuration,
usb_hcd_alloc_bandwidth() will drop all non-NULL endpoints in udev->ep_out
and udev->ep_in before adding any new endpoints. However, when the new
UAS configuration was added, all those entries were null, so none of the
old endpoints in the BOT configuration were dropped.
The xHCI driver blindly added the UAS configuration endpoints, and some of
the endpoint addresses overlapped with the old BOT configuration
endpoints. This caused the xHCI host to reject the Configure Endpoint
command. Now that the xHCI driver code is cleaned up to reject a
double-add of active endpoints, we need to fix the USB core to properly
drop old endpoints in usb_disable_device().
If the host controller driver needs bandwidth checking support, make
usb_disable_device() call usb_disable_endpoint() with
reset_hardware set to false, drop the endpoints from the xHCI host
controller, and then call usb_disable_endpoint() again with
reset_hardware set to true.
The first call to usb_disable_endpoint() will cancel any pending URBs and
wait on them to be freed in usb_hcd_disable_endpoint(), but will keep the
pointers in udev->ep_out and udev->ep in intact. Then
usb_hcd_alloc_bandwidth() will use those pointers to know which endpoints
to drop.
The final call to usb_disable_endpoint() will do two things:
1. It will call usb_hcd_disable_endpoint() again, which should be harmless
since the ep->urb_list should be empty after the first call to
usb_disable_endpoint() returns.
2. It will set the entries in udev->ep_out and udev->ep in to NULL, and call
usb_hcd_disable_endpoint(). That call will have no effect, since the xHCI
driver doesn't set the endpoint_disable function pointer.
Note that usb_disable_device() will now need to be called with
hcd->bandwidth_mutex held.
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Tanya Brokhman <tlinder@codeaurora.org> Cc: ablay@codeaurora.org Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the xHCI driver encounters a Missed Service Interval event for an
isochronous endpoint ring, it means the host controller skipped over
one or more isochronous TDs. For TD that is skipped, skip_isoc_td() is
called. This sets the frame descriptor status to -EXDEV, and also sets
the value stored in the int pointed to by status to -EXDEV.
If the isochronous TD happens to be the last TD in an URB,
handle_tx_event() will use the status variable to give back the URB to
the USB core. That means drivers will see urb->status as -EXDEV.
It turns out that EHCI, UHCI, and OHCI always set urb->status to zero for
an isochronous urb, regardless of what the frame status is. See
itd_complete() in ehci-sched.c:
} else {
/* URB was too late */
desc->status = -EXDEV;
}
}
/* ASSERT: it's really the last itd for this urb
list_for_each_entry (itd, &stream->td_list, itd_list)
BUG_ON (itd->urb == urb);
*/
/* give urb back to the driver; completion often (re)submits */
dev = urb->dev;
ehci_urb_done(ehci, urb, 0);
ehci_urb_done() completes the URB with the status of the third argument, which
is always zero in this case.
It turns out that many USB webcam drivers, such as uvcvideo, cannot
handle urb->status set to a non-zero value. They will not resubmit
their isochronous URBs in that case, and userspace will see a frozen
video.
Change the xHCI driver to be consistent with the EHCI and UHCI driver,
and always set urb->status to 0 for isochronous URBs.
This patch should be backported to kernels as old as 2.6.36
While trying to switch a UAS device from the BOT configuration to the UAS
configuration via the bConfigurationValue file, Tanya ran into an issue in
the USB core. usb_disable_device() sets entries in udev->ep_out and
udev->ep_out to NULL, but doesn't call into the xHCI bandwidth management
functions to remove the BOT configuration endpoints from the xHCI host's
internal structures.
The USB core would then attempt to add endpoints for the UAS
configuration, and some of the endpoints had the same address as endpoints
in the BOT configuration. The xHCI driver blindly added the endpoints
again, but the xHCI host controller rejected the Configure Endpoint
command because active endpoints were added without being dropped.
Make the xHCI driver reject calls to xhci_add_endpoint() that attempt to
add active endpoints without first calling xhci_drop_endpoint().
This should be backported to kernels as old as 2.6.31.
projects / karo-tx-linux.git / log