Jack Morgenstein [Tue, 13 Dec 2011 04:18:30 +0000 (04:18 +0000)]
mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: Liran Liss <liranl@mellanox.co.il> Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:17:16 +0000 (04:17 +0000)]
mlx4_core: adjust catas operation for SRIOV mode
When running in SRIOV mode, driver should not automatically start/stop
the mlx4_core upon sensing an HCA internal error -- doing this disables/enables
sriov, which will cause the hypervisor to hang if there are running VMs with
attached VFs.
In addition, on VMs the catas process should not run at all, since the HCA
error buffer is not available to VMs in the BARs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Apfelbaum [Tue, 13 Dec 2011 04:16:56 +0000 (04:16 +0000)]
mlx4_core: mtts resources units changed to offset
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en: Allow communication between functions on same host
To enable internal loopback, always fill DMAC in control segment
when transmitting the packet, once this is done, the packet is subject
for loopback for if the DMAC mathces one of the multicast/unicast addresses
registered on the physical port.
In receive path if source MAC is our own MAC and we are not in selftest,
or not in force LB mode - drop this packet.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4: Traffic steering management support for SRIOV
Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Tue, 13 Dec 2011 04:15:24 +0000 (04:15 +0000)]
mlx4_core: resource tracking for HCA resources used by guests
The resource tracker is used to track usage of HCA resources by the different
guests.
Virtual functions (VFs) are attached to guest operating systems but
resources are allocated from the same pool and are assigned to VFs. It is
essential that hostile/buggy guests not be able to affect the operation of
other VFs, possibly attached to other guest OSs since ConnectX firmware is not
tolerant to misuse of resources.
The resource tracker module associates each resource with a VF and maintains
state information for the allocated object. It also defines allowed state
transitions and enforces them.
Relationships between resources are also referred to. For example, CQs are
pointed to by QPs, so it is forbidden to destroy a CQ if a QP refers to it.
ICM memory is always accessible through the primary function and hence it is
allocated by the owner of the primary function.
When a guest dies, an FLR is generated for all the VFs it owns and all the
resources it used are freed.
The tracked resource types are: QPs, CQs, SRQs, MPTs, MTTs, MACs, RES_EQs,
and XRCDNs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:13:58 +0000 (04:13 +0000)]
mlx4_core: Add wrapper functions and comm channel and slave event support to EQs
Passing async events to slaves:
In SRIOV mode, each slave creates its own async EQ, but only the master can
register directly with the FW to receive async events. Async events which
should be passed to slaves (such as a WQ_ACCESS_ERROR for a QP owned by a slave)
are generated at the slave by the master using the GEN_EQE FW command.
Wrapper functions: mlx4_MAP_EQ_wrapper
Only the master can map an EQ. The slave commands to map their EQs arrive
at the master via the comm channel. The master then invokes the wrapper
function to do the work (and enter the resource in the tracking database).
New events: COMM_CHANNEL and FLR
The COMM_CHANNEL event arrives only at the master, and signals that
a slave has posted a command on the comm channel.
The FLR event is generated by the FW when a guest operating a VF
unexpectedly goes down.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:13:48 +0000 (04:13 +0000)]
mlx4_core: mtt modifications for SRIOV
MTTs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:13:36 +0000 (04:13 +0000)]
mlx4_core: cq modifications for SRIOV
CQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:13:22 +0000 (04:13 +0000)]
mlx4_core: qp modifications for SRIOV
QPs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:13:05 +0000 (04:13 +0000)]
mlx4_core: srq modifications for SRIOV
SRQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Apfelbaum [Tue, 13 Dec 2011 04:12:40 +0000 (04:12 +0000)]
mlx4_core: Added FW commands and their wrappers for supporting SRIOV
The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when
they start up to receive configuration information from the PF, such
as resource quotas for this VF, which ports should be used (currently
two), what protocol is running on the port (currently Ethernet ONLY,
or port not active).
2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
required here (the VF's MAC address must be substituted for the PFs
MAC address returned by the FW). We changed the invocation
in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.
3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
For now, we need only the multicast table member entry size
(log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed
here, because the data may be passed as is to the VF without modification).
In this command, we have added a GLOBAL_CAPS field for passing required
configuration information from FW to a VF (this field is to allow safely
adding new SRIOV capabilities which require support in VF drivers, too).
Bits will set here by FW in response to PF-driver configuration commands which
will activate as yet undefined new SRIOV features. The VF will test to see that
all required capabilities indicated by this field are supported (i.e., if a bit
is set and the VF driver does not recognize that bit, it must abort
its initialization). Currently, no bits are set.
4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts
have the port open. The PF context will not actually issue the FW close port command
until the last port user issues a CLOSE_PORT request.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Tue, 13 Dec 2011 04:12:25 +0000 (04:12 +0000)]
net/mlx4_core: Implement the master-slave communication channel
When SRIOV is enabled, pf and vfs communicate via shared comm channel.
The vf gets its side of the comm channel via a VF BAR.
Each VF (slave) creates its vHCR (virtual HCA Command Register),
Its DMA address is passed to the PF (master) using Communication Channel Register.
The same Register is used to notify the master of commands posted by the
slaves and for the master to pass events to the slaves, such as command completions
and asynchronous events.
The vHCR format is identical to the HCR format, except for the 'go' and 't' bits,
which are reserved in the vHCR. Posting commands to the vHCR is identical to
the way it is done with the HCR, albeit that the function/PF token fields are
used instead of the HCR go bit.
Specifically:
- When the function prepares a new command in the vHCR, it issues the Post_vHCR_cmd
communication channel command and toggles the value of the function token;
when PF token has an equal value, the command has been accepted and a new command may be posted.
- When the PF detects a Post_vHCR_cmd command, it concludes that a new command is available in the vHCR;
after processing the command, the PF toggles the PF token to match the function token.
When the 'e' bit is not set, the completion of a Post_vHCR_cmd command also indicates
the completion the vHCR command. If, however, the 'e' bit is set, the completion of a
Post_vHCR_cmd command only indicates that the vHCR command has been accepted for execution by the PF.
Function commands are processed by the PF as follows:
-DMA (using the ACCESS_MEM command) the vHCR image into a shadow buffer.
-Validate that the opcode is non-privileged, and that the opcode- and input-modifiers are legal.
-DMA the in-box (if required) into a shadow buffer.
-Validate the command:
o Resource ranges (e.g., QP ranges).
o Partition key.
o Ranges of referenced resources (e.g., CQs within QP contexts).
-If the 'e' bit is set
o complete the Post_vHCR_cmd command
-Execute the command on the HCR.
-DMA the results to the vHCR out-box (if required).
-If the 'e' bit is set
o Indicate command completion by generating a completion event using the GEN_EQE command
-Otherwise
o DMA the command status to the vHCR
o Complete the Post_vHCR_cmd command
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yevgeny Petrillin <yevgenyp@mellanox.com> Signed-off-by: Liran Liss <liranl@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:12:13 +0000 (04:12 +0000)]
mlx4_core: Reduce number of PD bits to 17
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.
Change the allocator to return only 17 bits for the PD. The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:10:51 +0000 (04:10 +0000)]
mlx4_core: Add "native" argument to mlx4_cmd and its callers (where needed)
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:10:41 +0000 (04:10 +0000)]
mlx4: Extanding port_mask functionality
Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 13 Dec 2011 04:10:33 +0000 (04:10 +0000)]
mlx4_core: initial header-file changes for SRIOV support
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 13 Dec 2011 03:59:08 +0000 (03:59 +0000)]
net: fix build error if CONFIG_CGROUPS=n
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Tue, 13 Dec 2011 00:58:50 +0000 (00:58 +0000)]
be2net: refactor/cleanup vf configuration code
- use adapter->num_vfs (and not the module param) to store the actual
number of vfs created. Use the same variable to reflect SRIOV
enable/disable state. So, drop the adapter->sriov_enabled field.
- use for_all_vfs() macro in VF configuration code
- drop the "vf_" prefix for the fields of be_vf_cfg; the prefix is
redundant and removing it helps reduce line wrap
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Tue, 13 Dec 2011 00:58:49 +0000 (00:58 +0000)]
be2net: fix ethtool ringparam reporting
The ethtool "-g" option is supposed to report the max queue length and
user modified queue length for RX and TX queues. be2net doesn't support
user modification of queue lengths. So, the correct values for these
would be the max numbers.
be2net incorrectly reports the queue used values for these fields.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netem: add cell concept to simulate special MAC behavior
This extension can be used to simulate special link layer
characteristics. Simulate because packet data is not modified, only the
calculation base is changed to delay a packet based on the original
packet size and artificial cell information.
packet_overhead can be used to simulate a link layer header compression
scheme (e.g. set packet_overhead to -20) or with a positive
packet_overhead value an additional MAC header can be simulated. It is
also possible to "replace" the 14 byte Ethernet header with something
else.
cell_size and cell_overhead can be used to simulate link layer schemes,
based on cells, like some TDMA schemes. Another application area are MAC
schemes using a link layer fragmentation with a (small) header each.
Cell size is the maximum amount of data bytes within one cell. Cell
overhead is an additional variable to change the per-cell-overhead
(e.g. 5 byte header per fragment).
Example (5 kbit/s, 20 byte per packet overhead, cell-size 100 byte, per
cell overhead 5 byte):
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:09 +0000 (21:47 +0000)]
Display maximum tcp memory allocation in kmem cgroup
This patch introduces kmem.tcp.max_usage_in_bytes file, living in the
kmem_cgroup filesystem. The root cgroup will display a value equal
to RESOURCE_MAX. This is to avoid introducing any locking schemes in
the network paths when cgroups are not being actively used.
All others, will see the maximum memory ever used by this cgroup.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:08 +0000 (21:47 +0000)]
Display current tcp failcnt in kmem cgroup
This patch introduces kmem.tcp.failcnt file, living in the
kmem_cgroup filesystem. Following the pattern in the other
memcg resources, this files keeps a counter of how many times
allocation failed due to limits being hit in this cgroup.
The root cgroup will always show a failcnt of 0.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:07 +0000 (21:47 +0000)]
Display current tcp memory allocation in kmem cgroup
This patch introduces kmem.tcp.usage_in_bytes file, living in the
kmem_cgroup filesystem. It is a simple read-only file that displays the
amount of kernel memory currently consumed by the cgroup.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:06 +0000 (21:47 +0000)]
tcp buffer limitation: per-cgroup limit
This patch uses the "tcp.limit_in_bytes" field of the kmem_cgroup to
effectively control the amount of kernel memory pinned by a cgroup.
This value is ignored in the root cgroup, and in all others,
caps the value specified by the admin in the net namespaces'
view of tcp_sysctl_mem.
If namespaces are being used, the admin is allowed to set a
value bigger than cgroup's maximum, the same way it is allowed
to set pretty much unlimited values in a real box.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:05 +0000 (21:47 +0000)]
per-netns ipv4 sysctl_tcp_mem
This patch allows each namespace to independently set up
its levels for tcp memory pressure thresholds. This patch
alone does not buy much: we need to make this values
per group of process somehow. This is achieved in the
patches that follows in this patchset.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:04 +0000 (21:47 +0000)]
tcp memory pressure controls
This patch introduces memory pressure controls for the tcp
protocol. It uses the generic socket memory pressure code
introduced in earlier patches, and fills in the
necessary data in cg_proto struct.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:03 +0000 (21:47 +0000)]
socket: initial cgroup code.
The goal of this work is to move the memory pressure tcp
controls to a cgroup, instead of just relying on global
conditions.
To avoid excessive overhead in the network fast paths,
the code that accounts allocated memory to a cgroup is
hidden inside a static_branch(). This branch is patched out
until the first non-root cgroup is created. So when nobody
is using cgroups, even if it is mounted, no significant performance
penalty should be seen.
This patch handles the generic part of the code, and has nothing
tcp-specific.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtsu.com> CC: Kirill A. Shutemov <kirill@shutemov.name> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Glauber Costa [Sun, 11 Dec 2011 21:47:02 +0000 (21:47 +0000)]
foundations of per-cgroup memory pressure controlling.
This patch replaces all uses of struct sock fields' memory_pressure,
memory_allocated, sockets_allocated, and sysctl_mem to acessor
macros. Those macros can either receive a socket argument, or a mem_cgroup
argument, depending on the context they live in.
Since we're only doing a macro wrapping here, no performance impact at all is
expected in the case where we don't have cgroups disabled.
Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Glauber Costa <glommer@parallels.com> CC: Kirill A. Shutemov <kirill@shutemov.name> CC: Paul Menage <paul@paulmenage.org> CC: Greg Thelen <gthelen@google.com> CC: Johannes Weiner <jweiner@redhat.com> CC: Michal Hocko <mhocko@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Laszlo Ersek [Sun, 11 Dec 2011 01:48:59 +0000 (01:48 +0000)]
xen-netfront: delay gARP until backend switches to Connected
After a guest is live migrated, the xen-netfront driver emits a gratuitous
ARP message, so that networking hardware on the target host's subnet can
take notice, and public routing to the guest is re-established. However,
if the packet appears on the backend interface before the backend is added
to the target host's bridge, the packet is lost, and the migrated guest's
peers become unable to talk to the guest.
A sufficient two-parts condition to prevent the above is:
(1) ensure that the backend only moves to Connected xenbus state after its
hotplug scripts completed, ie. the netback interface got added to the
bridge; and
(2) ensure the frontend only queues the gARP when it sees the backend move
to Connected.
These two together provide complete ordering. Sub-condition (1) is already
satisfied by commit f942dc2552b8 in Linus' tree, based on commit 6b0b80ca7165 from [1].
In general, the full condition is sufficient, not necessary, because,
according to [2], live migration has been working for a long time without
satisfying sub-condition (2). However, after 6b0b80ca7165 was backported
to the RHEL-5 host to ensure (1), (2) still proved necessary in the RHEL-6
guest. This patch intends to provide (2) for upstream.
Signed-off-by: Laszlo Ersek <lersek@redhat.com> Reviewed-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann [Sat, 10 Dec 2011 14:28:36 +0000 (15:28 +0100)]
batman-adv: Only write requested number of byte to user buffer
Don't write more than the requested number of bytes of an batman-adv icmp
packet to the userspace buffer. Otherwise unrelated userspace memory might get
overridden by the kernel.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Paul Kot [Sat, 10 Dec 2011 14:28:34 +0000 (15:28 +0100)]
batman-adv: bat_socket_read missing checks
Writing a icmp_packet_rr and then reading icmp_packet can lead to kernel
memory corruption, if __user *buf is just below TASK_SIZE.
Signed-off-by: Paul Kot <pawlkt@gmail.com>
[sven@narfation.org: made it checkpatch clean] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Pavel Emelyanov [Fri, 9 Dec 2011 23:33:43 +0000 (23:33 +0000)]
udp_diag: Make it module when ipv6 is a module
Eric Dumazet reported, that when inet_diag is built-in the udp_diag also goes
built-in and when ipv6 is a module the udp6 lookup symbol is not found.
LD .tmp_vmlinux1
net/built-in.o: In function `udp_dump_one':
udp_diag.c:(.text+0xa2b40): undefined reference to `__udp6_lib_lookup'
make: *** [.tmp_vmlinux1] Erreur 1
Fix this by making udp diag build mode depend on both -- inet diag and ipv6.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the regression was introduced between 20111202 and 20111205 (linux-next tree). Symptoms: connection to AP seem to be
established, but no data goes though it in any way. Tested on intel
5300.
Peek at the changes have shown that it looks like at least part of
the code wasn't merged properly. It was originally committed into
iwl_agn.c but code in question was moved to iwl-mac80211.c.
This patch puts code in place and my card works again.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx: silence tx_attr uninitialized warning in wl1271_tx_fill_hdr
CC [M] drivers/net/wireless/wl12xx/tx.o
drivers/net/wireless/wl12xx/tx.c: In function ‘wl1271_tx_fill_hdr’:
drivers/net/wireless/wl12xx/tx.c:288:6: warning: ‘tx_attr’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Fri, 9 Dec 2011 06:24:06 +0000 (06:24 +0000)]
udp_diag: Implement the get_exact dumping functionality
Do the same as TCP does -- lookup a socket in the given udp_table,
check cookie, fill the reply message with existing inet socket dumping
helper and send one back.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 9 Dec 2011 06:23:00 +0000 (06:23 +0000)]
inet_diag: Introduce the inet socket dumping routine
The existing inet_csk_diag_fill dumps the inet connection sock info
into the netlink inet_diag_message. Prepare this routine to be able
to dump only the inet_sock part of a socket if the icsk part is missing.
This will be used by UDP diag module when dumping UDP sockets.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 9 Dec 2011 06:22:26 +0000 (06:22 +0000)]
inet_diag: Split inet_diag_get_exact into parts
Similar to previous patch: the 1st part locks the inet handler
and will get generalized and the 2nd one dumps icsk-s and will
be used by TCP and DCCP handlers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 9 Dec 2011 06:22:10 +0000 (06:22 +0000)]
inet_diag: Split inet_diag_get_exact into parts
The 1st part locks the inet handler and the 2nd one dump the
inet connection sock.
In the next patches the 1st part will be generalized to call
the socket dumping routine indirectly (i.e. TCP/UDP/DCCP) and
the 2nd part will be used by TCP and DCCP handlers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 9 Dec 2011 06:21:16 +0000 (06:21 +0000)]
inet_diag: Remove indirect sizeof from inet diag handlers
There's an info_size value stored on inet_diag_handler, but for existing
code this value is effectively constant, so just use sizeof(struct tcp_info)
where required.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit breaks the build with CONFIG_NETPRIO_CGROUP=y so
revert it. It does build as a module though. The SUBSYS macro
in the cgroup core code automatically defines a subsys structure
as extern. Long term we should fix the macro. And I need to
fully build test things.
Tested with CONFIG_NETPRIO_CGROUP={y|m|n} with and without
CONFIG_CGROUPS defined.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> CC: Neil Horman <nhorman@tuxdriver.com> Reported-By: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 7 Dec 2011 20:49:38 +0000 (20:49 +0000)]
sock_diag: off by one checks
These tests are off by one because sock_diag_handlers[] only has AF_MAX
elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 7 Dec 2011 19:17:17 +0000 (19:17 +0000)]
net: netprio_cgroup: make net_prio_subsys static
net_prio_subsys can be made static this removes the sparse
warning it was throwing.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Thu, 8 Dec 2011 08:04:07 +0000 (08:04 +0000)]
bnx2x: properly initialize L5 features
The code is missing initialization of NO_FCOE_FLAG and NO_ISCSI*FLAGS
when CONFIG_CNIC is not selected.
This causes panic during driver load since commit 1d187b34daaecbb87aa523ba46b92930a388cb21 where NO_FCOE tested
unconditionally (outside #ifdef BCM_CNIC structure) and
accessed fp[FCOE_IDX] which is not allocated.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2011 06:06:03 +0000 (06:06 +0000)]
sch_red: Adaptative RED AQM
Adaptative RED AQM for linux, based on paper from Sally FLoyd,
Ramakrishna Gummadi, and Scott Shenker, August 2001 :
http://icir.org/floyd/papers/adaptiveRed.pdf
Goal of Adaptative RED is to make max_p a dynamic value between 1% and
50% to reach the target average queue : (max_th - min_th) / 2
Every 500 ms:
if (avg > target and max_p <= 0.5)
increase max_p : max_p += alpha;
else if (avg < target and max_p >= 0.01)
decrease max_p : max_p *= beta;
target :[min_th + 0.4*(min_th - max_th),
min_th + 0.6*(min_th - max_th)].
alpha : min(0.01, max_p / 4)
beta : 0.9
max_P is a Q0.32 fixed point number (unsigned, with 32 bits mantissa)
Changes against our RED implementation are :
max_p is no longer a negative power of two (1/(2^Plog)), but a Q0.32
fixed point number, to allow full range described in Adatative paper.
To deliver a random number, we now use a reciprocal divide (thats really
a multiply), but this operation is done once per marked/droped packet
when in RED_BETWEEN_TRESH window, so added cost (compared to previous
AND operation) is near zero.
dump operation gives current max_p value in a new TCA_RED_MAX_P
attribute.
Example on a 10Mbit link :
tc qdisc add dev $DEV parent 1:1 handle 10: est 1sec 8sec red \
limit 400000 min 30000 max 90000 avpkt 1000 \
burst 55 ecn adaptative bandwidth 10Mbit
# tc -s -d qdisc show dev eth3
...
qdisc red 10: parent 1:1 limit 400000b min 30000b max 90000b ecn
adaptative ewma 5 max_p=0.113335 Scell_log 15
Sent 50414282 bytes 34504 pkt (dropped 35, overlimits 1392 requeues 0)
rate 9749Kbit 831pps backlog 72056b 16p requeues 0
marked 1357 early 35 pdrop 0 other 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 8 Dec 2011 04:11:20 +0000 (04:11 +0000)]
team: use vlan_vids_[addr/del]_by_dev
So far when vlan id was added to team device befor port was added, this
vid was not added to port's vlan filter. Also after removal, vid stayed
in port device's vlan filter. Benefit of new vlan functions to handle
this work.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 9 Dec 2011 00:52:37 +0000 (19:52 -0500)]
net: make vlan ndo_vlan_rx_[add/kill]_vid return error value
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Waßmann [Wed, 7 Dec 2011 21:59:31 +0000 (21:59 +0000)]
net/fec: fix the .remove code
The .remove code is broken in several ways.
- mdiobus_unregister() is called twice for the same object in case of dual FEC
- phy_disconnect() is being called when the PHY is already disconnected
- the requested IRQ(s) are not freed
- fec_stop() is being called with the inteface already stopped
All of those lead to kernel crashes if the remove function is actually used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Waßmann [Wed, 7 Dec 2011 21:59:29 +0000 (21:59 +0000)]
net/fec: don't munge MAC address from platform data
When the MAC address is supplied via platform_data it should be OK as
it is and should not be modified in case of a dual FEC setup.
Also copying the MAC from platform_data to the single 'macaddr'
variable will overwrite the MAC for the first interface in case of a
dual FEC setup.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:18 +0000 (14:40 +0000)]
tg3: Update version to 3.122
This patch updates the tg3 version to 3.122.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:17 +0000 (14:40 +0000)]
tg3: Return flowctrl config through ethtool
This patch changes the driver to return the flow control configuration
rather than the flow control status through the ETHTOOL_GPAUSEPARAM
ioctl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:16 +0000 (14:40 +0000)]
tg3: Track LP advertising
This patch adds code to track the autonegotiation advertisements of the
link partner and report them through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:15 +0000 (14:40 +0000)]
tg3: Integrate flowctrl check into AN adv check
This patch integrates tg3_adv_1000T_flowctrl_ok() into
tg3_copper_is_advertising_all() and renames the function
tg3_phy_copper_an_config_ok().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:14 +0000 (14:40 +0000)]
tg3: Save stats across chip resets
Tg3 has a place to store stats, but doesn't really use it. This patch
modifies the driver so that stats are saved across chip resets and gets
cleared across close / open calls.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 8 Dec 2011 14:40:13 +0000 (14:40 +0000)]
tg3: Remove ethtool stats member from dev struct
This patch removes the ethtool stats member from the tg3 device
structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: add local MAC address to forwarding table (v2)
If user has configured a MAC address that is not one of the existing
ports of the bridge, then we need to add a special entry in the forwarding
table. This forwarding table entry has no outgoing port so it has to be
treated a little differently. The special entry is reported by the netlink
interface with ifindex of bridge, but ignored by the old interface since there
is no usable way to put it in the ABI.
Reported-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pass bridge to fdb_notify so it can determine correct namespace based
on namespace of bridge rather than namespace of destination port.
Also makes next patch easier.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eyal Shapira [Wed, 7 Dec 2011 10:37:04 +0000 (12:37 +0200)]
wl12xx: minor fix in sched_scan_ssid_list
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan.
In this case the loop was attempting to match SSIDs in the filter
list to this empty entry and marking them as HIDDEN (sending probe
request) by mistake
Eliad Peller [Tue, 6 Dec 2011 10:15:06 +0000 (12:15 +0200)]
wl12xx: remove redundant commands from plt init
During plt init we configure some redundant commands,
which are not needed for plt (specifically, we shouldn't
configure any role-specific params, as there are no
active roles). remove them.
Eliad Peller [Tue, 6 Dec 2011 10:15:05 +0000 (12:15 +0200)]
wl12xx: fix testmode test/interrogate commands
fix several issues in testmode test/interrogate commands:
1. check the driver state is not OFF.
2. wakeup the chip from elp (if needed)
3. fix memory leak in wl1271_tm_cmd_interrogate()
Enable ANI for ar9100 since it seems to be working fine (and as a
matter of fact ANI was always performed for ar9100 since code which
was supposed to disable it didn't achieve this goal).
This patch sets config.enable_ani to default (true) value for
ar9100.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: use config.enable_ani to check if ani should be performed
Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log