Stefan Roese [Tue, 26 Jan 2010 05:56:30 +0000 (05:56 +0000)]
powerpc/44x: Add MTD support (NOR FLASH) to Katmai dts
This patch adds NOR FLASH MTD support to the Katmai (440SPe) dts file.
For this the OPB ranges address is mapped differently (base 0x00000000
-> 0xe0000000). This results in the address being identical to the lower
32bit of its physical address. This is needed for the MTD mapping to work
correctly, since U-Boot will insert the physical addresses of the EBC
chip selects into the EBC ranges property. This is the way its done in
most other 4xx dts files as well.
Anton Blanchard [Sun, 7 Feb 2010 19:37:29 +0000 (19:37 +0000)]
powerpc: Clear MSR_RI during RTAS calls
RTAS should never cause an exception but if it does (for example accessing
outside our RMO) then we might go a long way through the kernel before
oopsing. If we unset MSR_RI we should at least stop things on exception
exit.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Frans Pop [Sat, 6 Feb 2010 07:47:20 +0000 (07:47 +0000)]
powerpc: Remove trailing space in messages
Signed-off-by: Frans Pop <elendil@planet.nl> Cc: linuxppc-dev@ozlabs.org Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sun, 7 Feb 2010 12:26:28 +0000 (12:26 +0000)]
powerpc: Reduce differences between pseries and ppc64 defconfigs
The pseries and ppc64 defconfigs have drifted apart over the years. Reduce
some of the differences while still keeping the idea that the ppc64 defconfig
is cross platform but enables fewer features than pseries, eg NR_CPUS is
lower.
Also enable a number of common adapters as modules.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The tb_total and purr_total values reported via the hcall_stats code
should be cumulative, rather than being replaced by the latest delta tb
or purr value.
Tested-by: Will Schmidt <will_schmidt@vnet.ibm.com> Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pseries: Pass more accurate number of supported cores to firmware
Updated variant of a patch by Joel Schopp.
The field containing the number of supported cores which we pass to
firmware via the ibm,client-architecture call was set by a previous
patch statically as high as is possible (NR_CPUS).
However, that value isn't quite right for a system that supports
multiple threads per core, thus permitting the firmware to assign
more cores to a Linux partition than it can really cope with.
This patch improves it by using the device-tree to determine the
number of threads supported by the processors in order to adjust
the value passed to firmware.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Add static fields to ibm,client-architecture call
This patch adds 2 fields to the ibm_architecture_vec array.
The first of these fields indicates the number of cores which Linux can
boot. It does not account for SMT, so it may result in cpus assigned to
Linux which cannot be booted. A second patch follows that dynamically
updates this for SMT.
The second field just indicates that our OS is Linux, and not another
OS. The system may or may not use this hint to performance tune
settings for Linux.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 12 Jan 2010 21:25:24 +0000 (21:25 +0000)]
lmb: Add lmb_free()
We can free memory allocated with lmb_alloc() by removing it from the
list of reserved LMBs. Rework lmb_remove() to allow that possibility
and add lmb_free() which exploits it.
BenH: Removed some useless parenthesis
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sun, 31 Jan 2010 01:14:03 +0000 (01:14 +0000)]
powerpc: Increase NR_IRQS Kconfig maximum to 32768
With dynamic irq descriptors the overhead of a large NR_IRQS is much lower
than it used to be. With more MSI-X capable adapters and drivers exploiting
multiple vectors we may as well allow the user to increase it beyond the
current maximum of 512.
32768 seems large enough that we'd never have to bump it again (although I bet
my prediction is horribly wrong). It boot tests OK and the vmlinux footprint
increase is only around 500kB due to:
struct irq_map_entry irq_map[NR_IRQS];
We format /proc/interrupts correctly with the previous changes:
Jean Delvare [Sun, 31 Jan 2010 04:03:23 +0000 (04:03 +0000)]
macintosh/hwmon/ams: Fix device removal sequence
Some code that is in ams_exit() (the module exit code) should instead
be called when the device (not module) is removed. It probably doesn't
make much of a difference in the PMU case, but in the I2C case it does
matter.
I make no guarantee that my fix isn't racy, I'm not familiar enough
with the ams driver code to tell for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Stelian Pop <stelian@popies.net> Cc: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: stable@kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Looking at drivers/macintosh/therm_adt746x.c, the sysfs files are
created in thermostat_init() and removed in thermostat_exit(), which
are the driver's init and exit functions. These files are backed-up by
a per-device structure, so it looks like the wrong thing to do: the
sysfs files have a lifetime longer than the data structure that is
backing it up.
I think that sysfs files creation should be moved to the end of
probe_thermostat() and sysfs files removal should be moved to the
beginning of remove_thermostat().
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Colin Leroy <colin@colino.net> Cc: stable@kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Amit Shah [Mon, 18 Jan 2010 03:44:58 +0000 (03:44 +0000)]
hvc_console: Remove __devinit annotation from hvc_alloc
Virtio consoles can be hotplugged, so hvc_alloc gets called from
multiple sites: from the initial probe() routine as well as later on
from workqueue handlers which aren't __devinit code.
So, drop the __devinit annotation for hvc_alloc.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Cc: linuxppc-dev@ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rusty Russell [Mon, 18 Jan 2010 03:44:57 +0000 (03:44 +0000)]
hvc_console: Make the ops pointer const.
This is nicer for modern R/O protection. And noone needs it non-const, so
constify the callers as well.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Amit Shah <amit.shah@redhat.com>
To: Christian Borntraeger <borntraeger@de.ibm.com> Cc: linuxppc-dev@ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Peter Tyser [Fri, 18 Dec 2009 12:50:37 +0000 (12:50 +0000)]
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
Recent U-Boot commit 5ccd29c3679b3669b0bde5c501c1aa0f325a7acb caused
the "cpu-release-addr" device tree property to contain the physical RAM
location that secondary cores were spinning at. Previously, the
"cpu-release-addr" property contained a value referencing the boot page
translation address range of 0xfffffxxx, which then indirectly accessed
RAM.
The "cpu-release-addr" is currently ioremapped and the secondary cores
kicked. However, due to the recent change in "cpu-release-addr", it
sometimes points to a memory location in low memory that cannot be
ioremapped. For example on a P2020-based board with 512MB of RAM the
following error occurs on bootup:
<...>
mpic: requesting IPIs ...
__ioremap(): phys addr 0x1ffff000 is RAM lr c05df9a0
Unable to handle kernel paging request for data at address 0x00000014
Faulting instruction address: 0xc05df9b0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P2020 RDB
Modules linked in:
<... eventual kernel panic>
Adding logic to conditionally ioremap or access memory directly resolves
the issue.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Nate Case <ncase@xes-inc.com> Reported-by: Dipen Dudhat <B09055@freescale.com> Tested-by: Dipen Dudhat <B09055@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Tue, 12 Jan 2010 00:50:14 +0000 (00:50 +0000)]
powerpc: Mark some variables in the page fault path __read_mostly
Using perf to trace L1 dcache misses and dumping data addresses I found a few
variables taking a lot of misses. Since they are almost never written, they
should go into the __read_mostly section.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joe Perches [Tue, 22 Dec 2009 21:22:59 +0000 (21:22 +0000)]
powerpc/viodasd: Remove VIOD_KERN_<level> macros for printks
Use #define pr_fmt(fmt) "viod: " fmt
Remove #define VIOD_KERN_WARNING and VIOD_KERN_INFO
Convert printk(VIOD_KERN_<level> to pr_<level>
Coalesce long format strings
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
drivers/block/viodasd.c | 86 +++++++++++++++++++---------------------------
1 files changed, 36 insertions(+), 50 deletions(-) Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Tue, 2 Feb 2010 20:54:37 +0000 (12:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Do not idle on async queues
blk-cgroup: Fix potential deadlock in blk-cgroup
block: fix bugs in bio-integrity mempool usage
block: fix bio_add_page for non trivial merge_bvec_fn case
drbd: null dereference bug
drbd: fix max_segment_size initialization
Nick Piggin [Mon, 1 Feb 2010 11:25:57 +0000 (22:25 +1100)]
mm: purge fragmented percpu vmap blocks
Improve handling of fragmented per-CPU vmaps. We previously don't free
up per-CPU maps until all its addresses have been used and freed. So
fragmented blocks could fill up vmalloc space even if they actually had
no active vmap regions within them.
Add some logic to allow all CPUs to have these blocks purged in the case
of failure to allocate a new vm area, and also put some logic to trim
such blocks of a current CPU if we hit them in the allocation path (so
as to avoid a large build up of them).
Christoph reported some vmap allocation failures when using the per CPU
vmap APIs in XFS, which cannot be reproduced after this patch and the
previous bug fix.
Cc: linux-mm@kvack.org Cc: stable@kernel.org Tested-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Nick Piggin <npiggin@suse.de>
-- Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Mon, 1 Feb 2010 11:24:18 +0000 (22:24 +1100)]
mm: percpu-vmap fix RCU list walking
RCU list walking of the per-cpu vmap cache was broken. It did not use
RCU primitives, and also the union of free_list and rcu_head is
obviously wrong (because free_list is indeed the list we are RCU
walking).
While we are there, remove a couple of unused fields from an earlier
iteration.
These APIs aren't actually used anywhere, because of problems with the
XFS conversion. Christoph has now verified that the problems are solved
with these patches. Also it is an exported interface, so I think it
will be good to be merged now (and Christoph wants to get the XFS
changes into their local tree).
Cc: stable@kernel.org Cc: linux-mm@kvack.org Tested-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Nick Piggin <npiggin@suse.de>
-- Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 2 Feb 2010 20:47:51 +0000 (12:47 -0800)]
Merge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix access to released memory in clk_debugfs_register_one()
sh: Fix access to released memory in dwarf_unwinder_cleanup()
usb: r8a66597-hdc disable interrupts fix
spi: spi_sh_msiof: Fixed data sampling on the correct edge
Linus Torvalds [Tue, 2 Feb 2010 20:37:44 +0000 (12:37 -0800)]
Fix 'flush_old_exec()/setup_new_exec()' split
Commit 221af7f87b9 ("Split 'flush_old_exec' into two functions") split
the function at the point of no return - ie right where there were no
more error cases to check. That made sense from a technical standpoint,
but when we then also combined it with the actual personality setting
going in between flush_old_exec() and setup_new_exec(), it needs to be a
bit more careful.
In particular, we need to make sure that we really flush the old
personality bits in the 'flush' stage, rather than later in the 'setup'
stage, since otherwise we might be flushing the _new_ personality state
that we're just setting up.
So this moves the flags and personality flushing (and 'flush_thread()',
which is the arch-specific function that generally resets lazy FP state
etc) of the old process into flush_old_exec(), so that it doesn't affect
any state that execve() is setting up for the new process environment.
This was reported by Michal Simek as breaking his Microblaze qemu
environment.
Reported-and-tested-by: Michal Simek <michal.simek@petalogix.com> Cc: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vivek Goyal [Tue, 2 Feb 2010 19:45:46 +0000 (20:45 +0100)]
cfq-iosched: Do not idle on async queues
Few weeks back, Shaohua Li had posted similar patch. I am reposting it
with more test results.
This patch does two things.
- Do not idle on async queues.
- It also changes the write queue depth CFQ drives (cfq_may_dispatch()).
Currently, we seem to driving queue depth of 1 always for WRITES. This is
true even if there is only one write queue in the system and all the logic
of infinite queue depth in case of single busy queue as well as slowly
increasing queue depth based on last delayed sync request does not seem to
be kicking in at all.
This patch will allow deeper WRITE queue depths (subjected to the other
WRITE queue depth contstraints like cfq_quantum and last delayed sync
request).
Shaohua Li had reported getting more out of his SSD. For me, I have got
one Lun exported from an HP EVA and when pure buffered writes are on, I
can get more out of the system. Following are test results of pure
buffered writes (with end_fsync=1) with vanilla and patched kernel. These
results are average of 3 sets of run with increasing number of threads.
I also ran buffered writes along with some sequential reads and some
buffered reads going on in the system on a SATA disk because the potential
risk could be that we should not be driving queue depth higher in presence
of sync IO going to keep the max clat low.
With some random and sequential reads going on in the system on one SATA
disk I did not see any significant increase in max clat. So it looks like
other WRITE queue depth control logic is doing its job. Here are the
results.
Magnus Damm [Wed, 27 Jan 2010 07:41:19 +0000 (07:41 +0000)]
usb: r8a66597-hdc disable interrupts fix
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Markus Pietrek [Tue, 2 Feb 2010 02:29:15 +0000 (11:29 +0900)]
spi: spi_sh_msiof: Fixed data sampling on the correct edge
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Herbert Xu [Sun, 31 Jan 2010 22:17:56 +0000 (09:17 +1100)]
crypto: padlock-sha - Add import/export support
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Matt Mackall [Fri, 29 Jan 2010 08:50:36 +0000 (21:50 +1300)]
random: drop weird m_time/a_time manipulation
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Manuel Lauss [Tue, 26 Jan 2010 19:39:33 +0000 (20:39 +0100)]
MIPS: Alchemy: Fix dbdma ring destruction memory debugcheck.
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org> Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Mon, 1 Feb 2010 18:57:12 +0000 (10:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: AM3517: ASoC driver not getting compiled
ASoC: AIC23: Fixing writes to non-existing registers in resume function
ALSA: hda - Add an ASUS mobo to MSI blacklist
Linus Torvalds [Mon, 1 Feb 2010 18:46:49 +0000 (10:46 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
Linus Torvalds [Mon, 1 Feb 2010 18:45:00 +0000 (10:45 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
hw_breakpoints: Release the bp slot if arch_validate_hwbkpt_settings() fails.
perf: Ignore perf.data.old
perf report: Fix segmentation fault when running with '-g none'
Linus Torvalds [Mon, 1 Feb 2010 18:44:36 +0000 (10:44 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Correct printk whitespace in warning from cpu down task check
sched: Fix incorrect sanity check
sched: Fix fork vs hotplug vs cpuset namespaces
Linus Torvalds [Mon, 1 Feb 2010 18:43:01 +0000 (10:43 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/documentation: Cover new frame pointer semantics
tracing/documentation: Fix a typo in ftrace.txt
ring-buffer: Check for end of page in iterator
ring-buffer: Check if ring buffer iterator has stale data
tracing: Prevent kernel oops with corrupted buffer
Linus Torvalds [Mon, 1 Feb 2010 18:42:35 +0000 (10:42 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
Mark Brown [Mon, 4 Jan 2010 15:30:54 +0000 (15:30 +0000)]
regulator: Specify REGULATOR_CHANGE_STATUS for WM835x LED constraints
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ince gfs2 writes the rindex file a block at a time, and releases the
exclusive lock after each block, it is possible that another process
will grab the lock in the middle of the write. Since rindex entries are
not an even divisor of blocks, that other process may see partial
entries. On grows, this is fine. The process can simply ignore the the
partial entires. Previously, the code withdrew when it saw partial
entries. Now it simply ignores them.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Michel Dänzer [Fri, 22 Jan 2010 08:20:00 +0000 (09:20 +0100)]
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 1 Feb 2010 01:35:47 +0000 (11:35 +1000)]
drm/radeon/kms: move radeon KMS on/off switch out of staging.
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Jerome Glisse [Fri, 22 Jan 2010 14:19:00 +0000 (15:19 +0100)]
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Peter Hanzel [Sat, 30 Jan 2010 03:38:07 +0000 (03:38 +0000)]
drm/vmwgfx: Request SVGA version 2 and bail if not found
This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Richard Kennedy [Tue, 26 Jan 2010 17:10:48 +0000 (17:10 +0000)]
drm/ttm: remove padding from ttm_ref_object on 64bit builds
Re-order structure ttm_ref_object to remove 8 bytes of alignment padding
on 64 bit builds, so shrinking its size from 72 to 64 bytes allowing it
to fit into a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Acked-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
John Kacur [Sun, 31 Jan 2010 19:38:03 +0000 (20:38 +0100)]
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
First call drm_agp_acquire to check if agp has been acquired.
Second call drm_agp_info to fill in the info data struct, including aper_size.
Finally do the check to see if the aper_size makes sense.
Signed-off-by: John Kacur <jkacur@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.
This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.
V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.
V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.
Jason Wessel [Thu, 28 Jan 2010 23:04:43 +0000 (17:04 -0600)]
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
This patch fixes the regression in functionality where the
kernel debugger and the perf API do not nicely share hw
breakpoint reservations.
The kernel debugger cannot use any mutex_lock() calls because it
can start the kernel running from an invalid context.
A mutex free version of the reservation API needed to get
created for the kernel debugger to safely update hw breakpoint
reservations.
The possibility for a breakpoint reservation to be concurrently
processed at the time that kgdb interrupts the system is
improbable. Should this corner case occur the end user is
warned, and the kernel debugger will prohibit updating the
hardware breakpoint reservations.
Any time the kernel debugger reserves a hardware breakpoint it
will be a system wide reservation.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: kgdb-bugreport@lists.sourceforge.net Cc: K.Prasad <prasad@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-3-git-send-email-jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jason Wessel [Thu, 28 Jan 2010 23:04:42 +0000 (17:04 -0600)]
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
In the 2.6.33 kernel, the hw_breakpoint API is now used for the
performance event counters. The hw_breakpoint_handler() now
consumes the hw breakpoints that were previously set by kgdb
arch specific code. In order for kgdb to work in conjunction
with this core API change, kgdb must use some of the low level
functions of the hw_breakpoint API to install, uninstall, and
deal with hw breakpoint reservations.
The kgdb core required a change to call kgdb_disable_hw_debug
anytime a slave cpu enters kgdb_wait() in order to keep all the
hw breakpoints in sync as well as to prevent hitting a hw
breakpoint while kgdb is active.
During the architecture specific initialization of kgdb, it will
pre-allocate 4 disabled (struct perf event **) structures. Kgdb
will use these to manage the capabilities for the 4 hw
breakpoint registers, per cpu. Right now the hw_breakpoint API
does not have a way to ask how many breakpoints are available,
on each CPU so it is possible that the install of a breakpoint
might fail when kgdb restores the system to the run state. The
intent of this patch is to first get the basic functionality of
hw breakpoints working and leave it to the person debugging the
kernel to understand what hw breakpoints are in use and what
restrictions have been imposed as a result. Breakpoint
constraints will be dealt with in a future patch.
While atomic, the x86 specific kgdb code will call
arch_uninstall_hw_breakpoint() and arch_install_hw_breakpoint()
to manage the cpu specific hw breakpoints.
The net result of these changes allow kgdb to use the same pool
of hw_breakpoints that are used by the perf event API, but
neither knows about future reservations for the available hw
breakpoint slots.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: kgdb-bugreport@lists.sourceforge.net Cc: K.Prasad <prasad@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-2-git-send-email-jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Härdeman [Thu, 28 Jan 2010 20:02:54 +0000 (21:02 +0100)]
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
Commit 6aa542a694dc9ea4344a8a590d2628c33d1b9431 added a quirk for the
Intel DG45ID board due to low memory corruption. The Intel DG45FC
shares the same BIOS (and the same bug) as noted in:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: David Härdeman <david@hardeman.nu>
LKML-Reference: <20100128200254.GA9134@hardeman.nu> Cc: <stable@kernel.org> Cc: Alexey Fisher <bug-track@fisher-privat.net> Cc: ykzhao <yakui.zhao@intel.com> Cc: Tony Bones <aabonesml@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Hugh Dickins [Fri, 29 Jan 2010 17:46:34 +0000 (17:46 +0000)]
mm: fix migratetype bug which slowed swapping
After memory pressure has forced it to dip into the reserves, 2.6.32's 5f8dcc21211a3d4e3a7a5ca366b469fb88117f61 "page-allocator: split per-cpu
list into one-list-per-migrate-type" has been returning MIGRATE_RESERVE
pages to the MIGRATE_MOVABLE free_list: in some sense depleting reserves.
Fix that in the most straightforward way (which, considering the overheads
of alternative approaches, is Mel's preference): the right migratetype is
already in page_private(page), but free_pcppages_bulk() wasn't using it.
How did this bug show up? As a 20% slowdown in my tmpfs loop kbuild
swapping tests, on PowerMac G5 with SLUB allocator. Bisecting to that
commit was easy, but explaining the magnitude of the slowdown not easy.
The same effect appears, but much less markedly, with SLAB, and even
less markedly on other machines (the PowerMac divides into fewer zones
than x86, I think that may be a factor). We guess that lumpy reclaim
of short-lived high-order pages is implicated in some way, and probably
this bug has been tickling a poor decision somewhere in page reclaim.
But instrumentation hasn't told me much, I've run out of time and
imagination to determine exactly what's going on, and shouldn't hold up
the fix any longer: it's valid, and might even fix other misbehaviours.
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: check total number of devices when removing missing
Btrfs: check return value of open_bdev_exclusive properly
Btrfs: do not mark the chunk as readonly if in degraded mode
Btrfs: run orphan cleanup on default fs root
Btrfs: fix a memory leak in btrfs_init_acl
Btrfs: Use correct values when updating inode i_size on fallocate
Btrfs: remove tree_search() in extent_map.c
Btrfs: Add mount -o compress-force
H. Peter Anvin [Fri, 29 Jan 2010 06:14:43 +0000 (22:14 -0800)]
x86: get rid of the insane TIF_ABI_PENDING bit
Now that the previous commit made it possible to do the personality
setting at the point of no return, we do just that for ELF binaries.
And suddenly all the reasons for that insane TIF_ABI_PENDING bit go
away, and we can just make SET_PERSONALITY() just do the obvious thing
for a 32-bit compat process.
Everything becomes much more straightforward this way.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 29 Jan 2010 06:14:42 +0000 (22:14 -0800)]
Split 'flush_old_exec' into two functions
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anuj Aggarwal [Fri, 29 Jan 2010 10:19:22 +0000 (15:49 +0530)]
ASoC: AM3517: ASoC driver not getting compiled
Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes
CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the
Makefile. Whereas the config option defined in Kconfig is
SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517
was not getting compiled.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Anuj Aggarwal [Fri, 29 Jan 2010 08:28:55 +0000 (13:58 +0530)]
ASoC: AIC23: Fixing writes to non-existing registers in resume function
Commit e9ff5eb2 (Fixing infinite loop in resume path) uses wrong AIC23
register in resume function because of which register writes happen
on some non-existing registers.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Henrik Rydberg [Fri, 29 Jan 2010 06:28:27 +0000 (22:28 -0800)]
Input: add the ABS_MT_PRESSURE event
For pressure-based multi-touch devices, a direct way to send sensor
intensity data per finger is needed. This patch adds the ABS_MT_PRESSURE
event to the MT protocol.
Requested-by: Yoonyoung Shim <jy0922.shim@samsung.com> Requested-by: Mika Kuoppala <mika.kuoppala@nokia.com> Requested-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
projects / linux-beck.git / log