Roman Peniaev [Tue, 10 Jun 2014 14:57:02 +0000 (23:57 +0900)]
mmc: mxs: fix card detection in case of 'broken-cd' flag set
In case of reboot my olinuxino imx23 board does not see
mmc card any more. mmc_rescan is being called by delayed
work in loop, but mxs_mmc_get_cd always returns 0, so we
will never pass the card detection check and will not do
further card inition.
This patch is just an attempt to partially revert the patch a91fe279ae of Sascha Hauer, where it is claimed that upper
layer will handle broken card detection using the polling
logic and MMC_CAP_NEEDS_POLL capability, but seems it is not
true, because upper logic still expects 1 from 'get_cd'.
So, here we always return 1 (card present) in case of
MMC_CAP_NEEDS_POLL capability set.
Romain Izard [Fri, 27 Jun 2014 08:51:07 +0000 (10:51 +0200)]
mmc: Allow forward compatibility for eMMC
As stated by the eMMC 5.0 specification, a chip should not be rejected
only because of the revision stated in the EXT_CSD_REV field of the
EXT_CSD register.
Remove the control on this value, the control of the CSD_STRUCTURE field
should be sufficient to reject future incompatible changes.
Markus Mayer [Thu, 3 Jul 2014 20:27:42 +0000 (13:27 -0700)]
mmc: sdhci: Replace host->mmc with mmc where possible
After the switch to the MMC core regulator infrastucture, we already
have a local "mmc" pointer in various functions. There is no longer a
need to access the data structure via host->mmc.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Matt Porter <mporter@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Russell King [Thu, 26 Jun 2014 14:50:00 +0000 (15:50 +0100)]
mmc: sdhci: avoid double-delay while transitioning to 1.8V
The MMC core in mmc_set_signal_voltage() already provides for the delay
required to switch to 1.8V, so there is no need for drivers to perform
this wait themselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tim Kryger [Wed, 25 Jun 2014 07:25:34 +0000 (00:25 -0700)]
mmc: sdhci: Improve external VDD regulator support
A standard compliant SDHCI can itself supply VDD at 1.8, 3.0, or 3.3v.
Several vendors ignore this and instead rely upon external regulators
to supply VDD. While the external regulators typically can supply one
of the standard SDHCI voltage levels, there is no real reason for this
to be a hard requirement.
This patch alters the SDHCI driver such that external VDD regulators
that provide voltages other than the three mentioned above may be used
so long as they can supply a voltage that meets the needs of the card.
In the case that an external VDD regulator is provided, it is reasonable
to ignore the voltage capabilities of the host controller and allow the
external regulator to set the OCR mask. Additionally, there is no need
to convert a VDD voltage request into one of the standard SDHCI voltage
levels or program it in the host controller's power control register.
Axel Lin [Sun, 27 Apr 2014 10:25:31 +0000 (18:25 +0800)]
mmc: wmt-sdmmc: Remove deprecated IRQF_DISABLED
It's a NOOP since 2.6.35 and it will be removed one day.
This is not trivial because current code uses hard coded 32 instead of
IRQF_DISABLED in the request_irq call.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Axel Lin [Sun, 27 Apr 2014 10:22:51 +0000 (18:22 +0800)]
mmc: wmt-sdmmc: Fix settting BM_EIGHTBIT_MODE bit in wmt_mci_set_ios()
For MMC_BUS_WIDTH_8 case, current code missed setting BM_EIGHTBIT_MODE bit.
Also has a small refactor to make the code looks better in readability.
So the bit settings witch below logic:
SDMMC_BUSMODE register:
Set EIGHTBIT_MODE bit for 8 bit mode, Set FOURBIT_MODE bit for 4 bit mode.
Clear both EIGHTBIT_MODE and FOURBIT_MODE bits for 1 bit mode.
SDMMC_EXTCTRL register:
Set EXT_EIGHTBIT bit for 8 bit mode, Clear EXT_EIGHTBIT bit for 1/4 bit mode.
Add define for EXT_EIGHTBIT to avoid using magic number.
BM_ONEBIT_MASK is no longer used, thus remove it.
This patch is untested due to lack of platform with 8-bit hardware.
However since the code is there, it's good to make the code match the document.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Thu, 29 May 2014 08:28:05 +0000 (10:28 +0200)]
mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x
The am335x can't detect pending cirq in PM runtime suspend.
This patch reconfigures dat1 as a GPIO before going to suspend.
SDIO interrupts are detected with the GPIO, the GPIO will only wake
the module from suspend, SDIO irq detection will still happen through the
IP block.
Idea of remuxing the pins by Tony Lindgren. Code contributions from
Tony Lindgren and Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Balaji T K <balajitk@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Thu, 29 May 2014 08:28:04 +0000 (10:28 +0200)]
mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks
These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: Balaji T K <balajitk@ti.com> Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Thu, 29 May 2014 08:28:03 +0000 (10:28 +0200)]
mmc: omap_hsmmc: abort runtime suspend if pending sdio irq detected
On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: Balaji T K <balajitk@ti.com> Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Thu, 29 May 2014 08:28:00 +0000 (10:28 +0200)]
mmc: omap_hsmmc: Enable SDIO interrupt
There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.
Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.
This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.
This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.
Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>
For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.
To use it, you need to specify the wake-irq using the
interrupts-extended property.
Acked-by: Balaji T K <balajitk@ti.com> Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alexander Stein [Tue, 20 May 2014 11:29:21 +0000 (13:29 +0200)]
mmc: quirks: Fixup debug message
There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Dooks [Wed, 4 Jun 2014 11:42:13 +0000 (12:42 +0100)]
mmc: sh-mmcif: final error path cleanup
Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Dooks [Wed, 4 Jun 2014 11:42:12 +0000 (12:42 +0100)]
mmc: sh-mmcif: no need to call pm_runtime_suspend on error
The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Dooks [Wed, 4 Jun 2014 11:42:11 +0000 (12:42 +0100)]
mmc: sh-mmcif: use devm_ for irq management
Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Dooks [Wed, 4 Jun 2014 11:42:08 +0000 (12:42 +0100)]
mmc: sh-mmcif: update to print version and bus clock rate on probe
Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tim Kryger [Fri, 13 Jun 2014 17:13:56 +0000 (10:13 -0700)]
mmc: sdhci: Use mmc core regulator infrastucture
Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure. Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.
This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com> Signed-off-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Matt Porter <mporter@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a fake Qualcomm ID 0x00051180 to the amba_ids, as Qualcomm
SDCC controller is pl180, but amba id registers read 0x0's.
The plan is to remove SDCC driver totally and use mmci as the main SD
controller driver for Qualcomm SOCs.
MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.
Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".
This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.
This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.
mmc: mmci: Add support to data commands via variant structure.
On some SOCs like Qcom there are explicit bits in the command register
to specify if its a data transfer command or not. So this patch adds
support to such bits in variant data, giving more flexibility to the
driver.
mmc: mmci: add edge support to data and command out in variant data.
This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code to
special case them
This patch adds 8bit bus enable to variant structure giving more flexibility
to the driver to support more SOCs which have different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code
to special case them.
This patch adds ddrmode mask to variant structure giving more flexibility
to the driver to support more SOCs which have different datactrl register
layout.
Without this patch datactrl register is updated with incorrect ddrmode mask,
resulting in failures on Qualcomm SD Card Controller.
Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
mmc: mmci: Add enough delay between writes to CMD register.
On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.
One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.
mmc: mmci: Add Qualcomm specific register defines.
This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bugfix from Grant Likely:
"Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that
cannot be reached"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, tda998x and vmwgfx fixes,
The main one is i915 fix for missing VGA connectors, along with some
fixes for the tda998x from Russell fixing some modesetting problems.
(still on holidays, but got a spare moment to find these)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
which I introduced in the last round of cleanups :("
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix memory leak when calling irq_free_hwirqs()
irqchip: spear_shirq: Fix interrupt offset
irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
irqchip: armada-370-xp: Mask all interrupts during initialization.
Dave Airlie [Sat, 5 Jul 2014 21:49:59 +0000 (07:49 +1000)]
Merge tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 fixes from Catalin Marinas:
- Exception level check at boot time (for completeness, not triggering
any bug before)
- I/D-cache synchronisation logic for huge pages
- Config symbol typo
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix el2_setup check of CurrentEL
arm64: mm: Make icache synchronisation logic huge page aware
arm64: mm: Fix horrendous config typo
The mach-mxs platform is actually co-maintained by myself and
pengutronix folks. Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Olof Johansson [Sat, 5 Jul 2014 04:51:19 +0000 (21:51 -0700)]
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Maxime Ripard [Sun, 29 Jun 2014 13:48:53 +0000 (15:48 +0200)]
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
This partly reverts commits 553600502b84 (ARM: sunxi: Remove reset code from
the platform) and 5e669ec583e2 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 5 Jul 2014 04:45:38 +0000 (21:45 -0700)]
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Merge tag 'md/3.16-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Two minor bugfixes for md in 3.16"
* tag 'md/3.16-fixes' of git://neil.brown.name/md:
md: flush writes before starting a recovery.
md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status
Merge tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've queued up a few fixes in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix crash when starting transaction
Btrfs: fix btrfs_print_leaf for skinny metadata
Btrfs: fix race of using total_bytes_pinned
btrfs: use E2BIG instead of EIO if compression does not help
btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
Btrfs: fix use-after-free when cloning a trailing file hole
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
btrfs: fix null pointer dereference in clone_fs_devices when name is null
btrfs: fix nossd and ssd_spread mount option regression
Btrfs: fix race between balance recovery and root deletion
Btrfs: atomically set inode->i_flags in btrfs_update_iflags
btrfs: only unlock block in verify_parent_transid if we locked it
Btrfs: assert send doesn't attempt to start transactions
btrfs compression: reuse recently used workspace
Btrfs: fix crash when mounting raid5 btrfs with missing disks
btrfs: create sprout should rename fsid on the sysfs as well
btrfs: dev replace should replace the sysfs entry
btrfs: dev add should add its sysfs entry
btrfs: dev delete should remove sysfs entry
btrfs: rename add_device_membership to btrfs_kobj_add_device
Marc Zyngier [Fri, 6 Jun 2014 13:16:21 +0000 (14:16 +0100)]
arm64: fix el2_setup check of CurrentEL
The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.
It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Steve Capper [Wed, 2 Jul 2014 10:46:23 +0000 (11:46 +0100)]
arm64: mm: Make icache synchronisation logic huge page aware
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org> Tested-by: Mark Brown <broonie@linaro.org> Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> # v3.11+
Mengdong Lin [Thu, 3 Jul 2014 09:02:23 +0000 (17:02 +0800)]
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jani Nikula [Fri, 4 Jul 2014 02:00:37 +0000 (10:00 +0800)]
drm/i915: provide interface for audio driver to query cdclk
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
Merge tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver"
* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: tidspbridge: fix an erroneous removal of parentheses
iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
staging: iio/ad7291: fix error code in ad7291_probe()
iio:adc:ad799x: Fix reading and writing of event values, apply shift
Merge tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows"
* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
kernfs: kernfs_notify() must be useable from non-sleepable contexts
kills the uprobe. Along the way he found some other minor bugs and
clean ups that he fixed up making it a total of 4 patches.
Doing unrelated work, I found that the reading of the ftrace trace
file disables all function tracer callbacks. This was fine when
ftrace was the only user, but now that it's used by perf and kprobes,
this is a bug where reading trace can disable kprobes and perf. A
very unexpected side effect and should be fixed"
* tag 'trace-fixes-v3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove ftrace_stop/start() from reading the trace file
tracing/uprobes: Fix the usage of uprobe_buffer_enable() in probe_event_enable()
tracing/uprobes: Kill the bogus UPROBE_HANDLER_REMOVE code in uprobe_dispatcher()
uprobes: Change unregister/apply to WARN() if uprobe/consumer is gone
tracing/uprobes: Revert "Support mix of ftrace and perf"
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"There is one more fix for the relative paths series from -rc1: Print
the path to the build directory at the start of the build, so that
editors and IDEs can match the relative paths to source files"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Print the name of the build directory
Merge branch 'for-3.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"By coincidence, two NFSv4 symlink bugs, one introduced in the 3.16 xdr
encoding rewrite, the other a decoding bug that I think we've had
since the start but that just doesn't trigger very often"
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
Jan points out that I forgot to make the needed fixes to the
lz4_uncompress_unknownoutputsize() function to mirror the changes done
in lz4_decompress() with regards to potential pointer overflows.
The only in-kernel user of this function is the zram code, which only
takes data from a valid compressed buffer that it made itself, so it's
not a big issue. But due to external kernel modules using this
function, it's better to be safe here.
Reported-by: Jan Beulich <JBeulich@suse.com> Cc: "Don A. Bailey" <donb@securitymouse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[SCSI] use the scsi data buffer length to extract transfer size
Commit 8846bab180fa introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.
However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.
To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.
Reported-by: Christoph Hellwig <hch@infradead.org> Debugged-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Fixes: d77e65350f2d82dfa0557707d505711f5a43c8fd Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
shmem: fix init_page_accessed use to stop !PageLRU bug
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
fs/seq_file: fallback to vmalloc allocation
/proc/stat: convert to single_open_size()
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
msync: fix incorrect fstart calculation
zram: revalidate disk after capacity change
tools: memory-hotplug fix unexpected operator error
tools: cpu-hotplug fix unexpected operator error
autofs4: fix false positive compile error
slub: fix off by one in number of slab tests
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
shmem: fix init_page_accessed use to stop !PageLRU bug
Under shmem swapping load, I sometimes hit the VM_BUG_ON_PAGE(!PageLRU)
in isolate_lru_pages() at mm/vmscan.c:1281!
Commit 2457aec63745 ("mm: non-atomically mark page accessed during page
cache allocation where possible") looks like interrupted work-in-progress.
mm/filemap.c's call to init_page_accessed() is fine, but not mm/shmem.c's
- shmem_write_begin() is clearly wrong to use it after shmem_getpage(),
when the page is always visible in radix_tree, and often already on LRU.
Revert change to shmem_write_begin(), and use init_page_accessed() or
mark_page_accessed() appropriately for SGP_WRITE in shmem_getpage_gfp().
SGP_WRITE also covers shmem_symlink(), which did not mark_page_accessed()
before; but since many other filesystems use [__]page_symlink(), which did
and does mark the page accessed, consider this as rectifying an oversight.
Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Prabhakar Lad <prabhakar.csengg@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 2 Jul 2014 22:22:38 +0000 (15:22 -0700)]
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
Revert commit 939f04bec1a4 ("printk: enable interrupts before calling
console_trylock_for_printk()").
Andreas reported:
: None of the post 3.15 kernel boot for me. They all hang at the GRUB
: screen telling me it loaded and started the kernel, but the kernel
: itself stops before it prints anything (or even replaces the GRUB
: background graphics).
939f04bec1a4 is modest latency reduction. Revert it until we understand
the reason for these failures.
Reported-by: Andreas Bombe <aeb@debian.org> Cc: Jan Kara <jack@suse.cz> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
The test fails in the middle when it is not run as root while accessing
/proc/sys/kernel/msg_next_id. Changed it to check for root at the
beginning of the test and exit if not root.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Davidlohr Bueso <davidlohr@hp.com> Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a couple of seq_files which use the single_open() interface.
This interface requires that the whole output must fit into a single
buffer.
E.g. for /proc/stat allocation failures have been observed because an
order-4 memory allocation failed due to memory fragmentation. In such
situations reading /proc/stat is not possible anymore.
Therefore change the seq_file code to fallback to vmalloc allocations
which will usually result in a couple of order-0 allocations and hence
also work if memory is fragmented.
For reference a call trace where reading from /proc/stat failed:
These two patches are supposed to "fix" failed order-4 memory
allocations which have been observed when reading /proc/stat. The
problem has been observed on s390 as well as on x86.
To address the problem change the seq_file memory allocations to
fallback to use vmalloc, so that allocations also work if memory is
fragmented.
This approach seems to be simpler and less intrusive than changing
/proc/stat to use an interator. Also it "fixes" other users as well,
which use seq_file's single_open() interface.
This patch (of 2):
Use seq_file's single_open_size() to preallocate a buffer that is large
enough to hold the whole output, instead of open coding it. Also
calculate the requested size using the number of online cpus instead of
possible cpus, since the size of the output only depends on the number
of online cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Ian Kent <raven@themaw.net> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Thorsten Diehl <thorsten.diehl@de.ibm.com> Cc: Andrea Righi <andrea@betterlinux.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Stefan Bader <stefan.bader@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
Until now, the kernel has the same policy to handle victimized page
frames that belong to kernel-space(reserved/slab-subsystem) or
non-LRU(unknown page state). In other word, the result of handling
either of these victimized page frames is (IGNORED | FAILED), and the
return value of memory_failure() is -EBUSY.
This patch is to avoid that memory_failure() returns very soon due to
the "true" value of (!PageLRU(p)), and it also ensures that
action_result() can report more precise information("reserved kernel",
"kernel slab", and "unknown page state") instead of "non LRU",
especially for memory errors which are detected by memory-scrubbing.
Andi said:
: While running the mcelog test suite on 3.14 I hit the following VM_BUG_ON:
:
: soft_offline: 0x56d4: unknown non LRU page type 3ffff800008000
: page:ffffea000015b400 count:3 mapcount:2097169 mapping: (null) index:0xffff8800056d7000
: page flags: 0x3ffff800004081(locked|slab|head)
: ------------[ cut here ]------------
: kernel BUG at mm/rmap.c:1495!
:
: I think what happened is that a LRU page turned into a slab page in
: parallel with offlining. memory_failure initially tests for this case,
: but doesn't retest later after the page has been locked.
:
: ...
:
: I ran this patch in a loop over night with some stress plus
: the mcelog test suite running in a loop. I cannot guarantee it hit it,
: but it should have given it a good beating.
:
: The kernel survived with no messages, although the mcelog test suite
: got killed at some point because it couldn't fork anymore. Probably
: some unrelated problem.
:
: So the patch is ok for me for .16.
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
When using trace-vmscan-postprocess.pl for checking the file/anon rate
of scanning, we can find that it can not be performed. At the same
time, the following message will be reported:
WARNING: Format not as expected for event vmscan/mm_vmscan_lru_isolate
'file' != 'contig_taken' Fewer fields than expected in format at
./trace-vmscan-postprocess.pl line 171, <FORMAT> line 76.
In trace-vmscan-postprocess.pl, (contig_taken, contig_dirty, and
contig_failed) are be associated respectively to (nr_lumpy_taken,
nr_lumpy_dirty, and nr_lumpy_failed) for lumpy reclaim. Via commit c53919adc045 ("mm: vmscan: remove lumpy reclaim"), lumpy reclaim had
already been removed by Mel, but the update for
trace-vmscan-postprocess.pl was missed.
Minchan Kim [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
zram: revalidate disk after capacity change
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <minchan@kernel.org> Reported-by: Alexander E. Patrakov <patrakov@gmail.com> Tested-by: Alexander E. Patrakov <patrakov@gmail.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Nitin Gupta <ngupta@vflare.org> Acked-by: Jerome Marchand <jmarchan@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
Ian Kent [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
autofs4: fix false positive compile error
On strict build environments we can see:
fs/autofs4/inode.c: In function 'autofs4_fill_super':
fs/autofs4/inode.c:312: error: 'pgrp' may be used uninitialized in this function
make[2]: *** [fs/autofs4/inode.o] Error 1
make[1]: *** [fs/autofs4] Error 2
make: *** [fs] Error 2
make: *** Waiting for unfinished jobs....
This is due to the use of pgrp_set being used to indicate pgrp has has
been set rather than initializing pgrp itself.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
slub: fix off by one in number of slab tests
min_partial means minimum number of slab cached in node partial list.
So, if nr_partial is less than it, we keep newly empty slab on node
partial list rather than freeing it. But if nr_partial is equal or
greater than it, it means that we have enough partial slabs so should
free newly empty slab. Current implementation missed the equal case so
if we set min_partial is 0, then, at least one slab could be cached.
This is critical problem to kmemcg destroying logic because it doesn't
works properly if some slabs is cached. This patch fixes this problem.
Fixes 91cb69620284 ("slub: make dead memcg caches discard free slabs
immediately").
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = fffffe0000050000
[00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407
Internal error: Oops: 96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
â\80\9cpageblock_order > MAX_ORDERâ\80\9d condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> [3.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filipe Manana [Tue, 24 Jun 2014 16:46:58 +0000 (17:46 +0100)]
Btrfs: fix crash when starting transaction
Often when starting a transaction we commit the currently running transaction,
which can end up writing block group caches when the current process has its
journal_info set to NULL (and not to a transaction). This makes our assertion
at btrfs_check_data_free_space() (current_journal != NULL) fail, resulting
in a crash/hang. Therefore fix it by setting journal_info.
Liu Bo [Wed, 2 Jul 2014 08:58:01 +0000 (16:58 +0800)]
Btrfs: fix race of using total_bytes_pinned
This percpu counter @total_bytes_pinned is introduced to skip unnecessary
operations of 'commit transaction', it accounts for those space we may free
but are stuck in delayed refs.
And we zero out @space_info->total_bytes_pinned every transaction period so
we have a better idea of how much space we'll actually free up by committing
this transaction. However, we do the 'zero out' part a little earlier, before
we actually unpin space, so we end up returning ENOSPC when we actually have
free space that's just unpinned from committing transaction.
xfstests/generic/074 complained then.
This fixes it by actually accounting the percpu pinned number when 'unpin',
and since it's protected by space_info->lock, the race is gone now.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
David Sterba [Fri, 20 Jun 2014 09:43:20 +0000 (11:43 +0200)]
btrfs: use E2BIG instead of EIO if compression does not help
Return codes got updated in 60e1975acb48fc3d74a3422b21dde74c977ac3d5
(btrfs: return errno instead of -1 from compression)
lzo wrapper returns E2BIG in this case, do the same for zlib.
Anand Jain [Mon, 30 Jun 2014 09:12:48 +0000 (17:12 +0800)]
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
dev->name is null but missing flag is not set.
Strictly speaking the missing flag should have been set, but there
are more places where code just checks if name is null. For now this
patch does the same.
stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000064
IP: [<ffffffffa0228908>] btrfs_show_devname+0x58/0xf0 [btrfs]
Wang Shilong [Thu, 26 Jun 2014 03:08:16 +0000 (11:08 +0800)]
Btrfs: fix race between balance recovery and root deletion
Balance recovery is called when RW mounting or remounting from
RO to RW, it is called to finish roots merging.
When doing balance recovery, relocation root's corresponding
fs root(whose root refs is 0) might be destroyed by cleaner
thread, this will make btrfs fail to mount.
Fix this problem by holding @cleaner_mutex when doing balance
recovery.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
projects / karo-tx-linux.git / log