bcma: use fallback sprom if no on chip sprom is available
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge tag 'fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit 92ae03f2ef99 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Rabin Vincent [Sat, 14 Apr 2012 20:51:32 +0000 (21:51 +0100)]
ARM: 7386/1: jump_label: fixup for rename to static_key
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jonathan Austin [Thu, 12 Apr 2012 16:45:25 +0000 (17:45 +0100)]
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jonathan Austin <jonathan.austin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:15:08 +0000 (17:15 +0100)]
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@kernel.org Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 26f41062f28d ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Commit 18a4d0a22ed6 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com> Reported-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Kevin Hilman <khilman@ti.com> Acked-by: Paul Walmsley <paul@pwsan.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Olof Johansson <olof@lixom.net>
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Tested-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 15 Apr 2012 00:44:21 +0000 (17:44 -0700)]
Merge branch 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com> Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Abraham [Sat, 14 Apr 2012 15:12:04 +0000 (08:12 -0700)]
ARM: SAMSUNG: remove all uses of clk_type member in sdhci platform data
The sdhci driver is modified to be independent of clk_type member in the sdhci
platform data. Hence, all usage of clk_type in platform code is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: re-worked on top of v3.4-rc2] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Sat, 14 Apr 2012 15:04:46 +0000 (08:04 -0700)]
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
With the addition of platform specific driver data in the sdhci driver
for EXYNOS4 and EXYNOS5, the device name of sdhci controllers on EXYNOS4
and EXYNOS5 are changed accordingly.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: re-worked on top of v3.4-rc2] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Lubos Lunak [Wed, 21 Mar 2012 13:08:24 +0000 (14:08 +0100)]
do not export kernel's NULL #define to userspace
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: fix regulator name for NURI board
Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Don Skidmore [Thu, 5 Apr 2012 08:12:05 +0000 (08:12 +0000)]
ixgbe: fix WoL issue with fiber
There are times we turn of the laser before shutdown. This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 12 Apr 2012 06:27:03 +0000 (06:27 +0000)]
e1000e: issues in Sx on 82577/8/9
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge branch 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
Merge tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
"The fix for kyrofb is a bit large but it's just replacing "unsigned
long" by "u32" for 64 bit compatibility."
* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
fbdev: fix au1*fb builds
kyrofb: fix on x86_64
Merge branch 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull the minimal btrfs branch from Chris Mason:
"We have a use-after-free in there, along with errors when mount -o
discard is enabled, and a BUG_ON(we should compile with UP more
often)."
* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use commit root when loading free space cache
Btrfs: fix use-after-free in __btrfs_end_transaction
Btrfs: check return value of bio_alloc() properly
Btrfs: remove lock assert from get_restripe_target()
Btrfs: fix eof while discarding extents
Btrfs: fix uninit variable in repair_eb_io_failure
Revert "Btrfs: increase the global block reserve estimates"
Merge branch 'for-3.4/drivers' of git://git.kernel.dk/linux-block
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Merge branch 'for-3.4/core' of git://git.kernel.dk/linux-block
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
Kevin Hilman [Fri, 13 Apr 2012 20:32:30 +0000 (13:32 -0700)]
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO bug fixes from Grant Likely:
"Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warning in gpio-samsung.c file
gpio: Fix range check in of_gpio_simple_xlate()
gpio: Fix uninitialized variable bit in adp5588_irq_handler
gpio/sodaville: Convert sodaville driver to new irqdomain API
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
Paul E. McKenney [Fri, 13 Apr 2012 03:35:13 +0000 (03:35 +0000)]
sparc64: Eliminate obsolete __handle_softirq() function
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee> Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Meelis Roos <mroos@linux.ee> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 13 Apr 2012 18:56:22 +0000 (11:56 -0700)]
sparc64: Fix bootup crash on sun4v.
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: stable@vger.kernel.org
Will Deacon [Thu, 12 Apr 2012 05:54:09 +0000 (05:54 +0000)]
net: smsc911x: fix skb handling in receive path
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The scratch register addresses have been changed for newer chips.
Since the old chip was never shipped and it will not be supported
any more, just update register addresses to support the new chips.
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 12 Apr 2012 18:36:31 +0000 (20:36 +0200)]
ath9k: wake up the hardware from full sleep when idle is turned off
The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jonathan Bither [Thu, 12 Apr 2012 10:13:33 +0000 (06:13 -0400)]
ath5k: fix undefined 'THIS_MODULE'
When cross compiling ath5k for a Mips machine with kernel 3.2.14
the compilation fails with "/ath5k/ahb.c:231:12: error: 'THIS_MODULE' undeclared here (not in a function)"
Fix the build by including <linux/export.h>
Signed-off-by: Jonathan Bither <jonbither@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcm80211: smac: resume transmit fifo upon receiving frames
There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to
mac80211.
This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.
Cc: stable@vger.kernel.org Tested-by: Francesco Saverio Schiavarelli <fschiava@libero.it> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Brett Rudley <brudley@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Wed, 28 Mar 2012 18:38:01 +0000 (11:38 -0700)]
libertas: fix signedness bug in lbs_auth_to_authtype()
Return type for lbs_auth_to_authtype() is changed from "u8" to
"int" to return negative error code correctly.
Also an error check is added in connect handler for invalid auth
type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matt Renzelmann [Fri, 13 Apr 2012 07:59:40 +0000 (07:59 +0000)]
ks8851: Fix missing mutex_lock/unlock
Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use. A spurious interrupt may
otherwise cause a crash. Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 11 Apr 2012 22:10:54 +0000 (22:10 +0000)]
8139cp: set intr mask after its handler is registered
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Zelenoff [Wed, 11 Apr 2012 06:15:03 +0000 (06:15 +0000)]
atl1: fix kernel panic in case of DMA errors
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Daniel Walker [Thu, 12 Apr 2012 15:45:37 +0000 (08:45 -0700)]
arm: msm: trout: fix compile failure
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org Signed-off-by: David Brown <davidb@codeaurora.org>
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the alpha arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Some minor whitespace fixups were done on the block of code that
created the new file.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: David Howells <dhowells@redhat.com> Acked-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The skb struct ubuf_info callback gets passed struct ubuf_info
itself, not the arg value as the field name and the function signature
seem to imply. Rename the arg field to ctx to match usage,
add documentation and change the callback argument type
to make usage clear and to have compiler check correctness.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse [Sun, 8 Apr 2012 10:01:44 +0000 (10:01 +0000)]
ppp: Fix race condition with queue start/stop
Commit e675f0cc9a872fd152edc0c77acfed19bf28b81e ("ppp: Don't stop and
restart queue on every TX packet") introduced a race condition which
could leave the net queue stopped even when the channel is no longer
busy. By calling netif_stop_queue() from ppp_start_xmit(), based on the
return value from ppp_xmit_process() but *after* all the locks have been
dropped, we could potentially do so *after* the channel has actually
finished transmitting and attempted to re-wake the queue.
Fix this by moving the netif_stop_queue() into ppp_xmit_process() under
the xmit lock. I hadn't done this previously, because it gets called
from other places than ppp_start_xmit(). But I now think it's the better
option. The net queue *should* be stopped if the channel becomes
congested due to writes from pppd, anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.
Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.
rt6_check_expired check if rt6_info.dst.from is expired.
ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
ip6_dst_destroy release the ort.
Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.
Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.
Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Tue, 10 Apr 2012 00:10:43 +0000 (00:10 +0000)]
l2tp: don't overwrite source address in l2tp_ip_bind()
Applications using L2TP/IP sockets want to be able to bind() an L2TP/IP
socket to set the local tunnel id while leaving the auto-assigned source
address alone. So if no source address is supplied, don't overwrite
the address already stored in the socket.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Tue, 10 Apr 2012 00:10:42 +0000 (00:10 +0000)]
l2tp: fix refcount leak in l2tp_ip sockets
The l2tp_ip socket close handler does not update the module refcount
correctly which prevents module unload after the first bind() call on
an L2TPv3 IP encapulation socket.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Torsten Kaiser [Mon, 9 Apr 2012 05:14:15 +0000 (05:14 +0000)]
net: Fix misplaced parenthesis in virtio_net.c
Commit 2e57b79ccef1ff1422fdf45a9b28fe60f8f084f7 misplaced its
parenthesis and now tx_fifo_errors will only be incremented if an
ENOMEM error is not written to the syslog.
Correct the parenthesis and indentation to the original goal of
counting all non ENOMEM errors and ratelimiting only the messages.
Signed-of-by: Torsten Kaiser <just.for.lkml@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After investigation it turns out there were two issues.
1) Phonet was not implementing network devices but was using register_pernet_device
instead of register_pernet_subsys.
This was allowing there to be cases when phonenet was not initialized and
the phonet net_generic was not set for a network namespace when network
device events were being reported on the netdevice_notifier for a network
namespace leading to the oops above.
2) phonet_exit_net was implementing a confusing and special case of handling all
network devices from going away that it was hard to see was correct, and would
only occur when the phonet module was removed.
Now that unregister_netdevice_notifier has been modified to synthesize unregistration
events for the network devices that are extant when called this confusing special
case in phonet_exit_net is no longer needed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: In unregister_netdevice_notifier unregister the netdevices.
We already synthesize events in register_netdevice_notifier and synthesizing
events in unregister_netdevice_notifier allows to us remove the need for
special case cleanup code.
This change should be safe as it adds no new cases for existing callers
of unregiser_netdevice_notifier to handle.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Thu, 12 Apr 2012 16:16:01 +0000 (17:16 +0100)]
ARM: 7383/1: nommu: populate vectors page from paging_init
Commit 94e5a85b ("ARM: earlier initialization of vectors page") made it
the responsibility of paging_init to initialise the vectors page.
This patch adds a call to early_trap_init for the !CONFIG_MMU case,
placing the vectors at CONFIG_VECTORS_BASE.
Cc: Jonathan Austin <jonathan.austin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:56 +0000 (14:52 +0100)]
ARM: 7380/1: DT: do not add a zero-sized memory property
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:55 +0000 (14:52 +0100)]
ARM: 7379/1: DT: fix atags_to_fdt() second call site
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Fri, 13 Apr 2012 12:11:50 +0000 (13:11 +0100)]
ARM: 7366/3: amba: Remove AMBA level regulator support
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
In sound/pci/hda/patch_realtek.c::alc_auto_fill_dac_nids(), in the
'for (;;)' loop, if the 'badness' value returned from
fill_and_eval_dacs() is negative, then we'll return from the function
without freeing the memory we allocated for 'best_cfg', thus leaking.
Fix the leak by kfree()'ing the memory when badness is negative.
While I was there I also noticed some trailing whitespace in the
function that I removed (along with all other trailing whitespace in
the file) - it didn't seem worth-while to do that as two patches, so I
hope it's OK that I just did it all as one patch.
Paul Gortmaker [Thu, 12 Apr 2012 23:46:34 +0000 (19:46 -0400)]
kconfig: delete last traces of __enabled_ from autoconf.h
We've now fixed IS_ENABLED() and friends to not require any special
"__enabled_" prefixed versions of the normal Kconfig options, so delete
the last traces of them being generated.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dumping two lines into autoconf.h for all existing Kconfig options
results in a giant file (~16k lines) we have to process each time we
compile something. We've weaned IS_ENABLED() and similar off of
requiring the __enabled_ definitions so now we can revert the change
which caused all the extra lines.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Thu, 12 Apr 2012 23:46:32 +0000 (19:46 -0400)]
kconfig: fix IS_ENABLED to not require all options to be defined
Using IS_ENABLED() within C (vs. within CPP #if statements) in its
current form requires us to actually define every possible bool/tristate
Kconfig option twice (__enabled_* and __enabled_*_MODULE variants).
This results in a huge autoconf.h file, on the order of 16k lines for a
x86_64 defconfig.
Fixing IS_ENABLED to be able to work on the smaller subset of just
things that we really have defined is step one to fixing this. Which
means it has to not choke when fed non-enabled options, such as:
include/linux/netdevice.h:964:1: warning: "__enabled_CONFIG_FCOE_MODULE" is not defined [-Wundef]
The original prototype of how to implement a C and preprocessor
compatible way of doing this came from the Google+ user "comex ." in
response to Linus' crowdsourcing challenge for a possible improvement on
his earlier C specific solution:
Josef Bacik [Thu, 12 Apr 2012 20:03:57 +0000 (16:03 -0400)]
Btrfs: use commit root when loading free space cache
A user reported that booting his box up with btrfs root on 3.4 was way
slower than on 3.3 because I removed the ideal caching code. It turns out
that we don't load the free space cache if we're in a commit for deadlock
reasons, but since we're reading the cache and it hasn't changed yet we are
safe reading the inode and free space item from the commit root, so do that
and remove all of the deadlock checks so we don't unnecessarily skip loading
the free space cache. The user reported this fixed the slowness. Thanks,
Tested-by: Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Merge tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of fixes for the USB core and drivers for 3.4-rc2
Lots of tiny xhci fixes here, a few usb-serial driver fixes and new
device ids, and a smattering of other minor fixes in different USB
drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
USB: update usbtmc api documentation
xHCI: Correct the #define XHCI_LEGACY_DISABLE_SMI
xHCI: use gfp flags from caller instead of GFP_ATOMIC
xHCI: add XHCI_RESET_ON_RESUME quirk for VIA xHCI host
USB: fix bug of device descriptor got from superspeed device
xhci: Fix register save/restore order.
xhci: Restore event ring dequeue pointer on resume.
xhci: Don't write zeroed pointers to xHC registers.
xhci: Warn when hosts don't halt.
xhci: don't re-enable IE constantly
usb: xhci: fix section mismatch in linux-next
xHCI: correct to print the true HSEE of USBCMD
USB: serial: fix race between probe and open
UHCI: hub_status_data should indicate if ports are resuming
EHCI: keep track of ports being resumed and indicate in hub_status_data
USB: fix race between root-hub suspend and remote wakeup
USB: sierra: add support for Sierra Wireless MC7710
USB: ftdi_sio: fix race condition in TIOCMIWAIT, and abort of TIOCMIWAIT when the device is removed
USB: ftdi_sio: fix status line change handling for TIOCMIWAIT and TIOCGICOUNT
USB: don't ignore suspend errors for root hubs
...
Merge tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial fixes from Greg KH:
"Here are some tty and serial fixes for 3.4-rc2.
Most important here is the pl011 fix, which has been reported by about
100 different people, which means more people use it than I expected
:)
There are also some 8250 driver reverts due to some problems reported
by them. And other minor fixes as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pch_uart: Add Kontron COMe-mTT10 uart clock quirk
pch_uart: Fix MSI setting issue
serial/8250_pci: add a "force background timer" flag and use it for the "kt" serial port
Revert "serial/8250_pci: setup-quirk workaround for the kt serial controller"
Revert "serial/8250_pci: init-quirk msi support for kt serial controller"
tty/serial/omap: console can only be built-in
serial: samsung: fix omission initialize ulcon in reset port fn()
printk(): add KERN_CONT where needed in hpet and vt code
tty/serial: atmel_serial: fix RS485 half-duplex problem
tty: serial: altera_uart: Check for NULL platform_data in probe.
isdn/gigaset: use gig_dbg() for debugging output
omap-serial: Fix the error handling in the omap_serial probe
serial: PL011: move interrupt clearing
Merge tag 'staging-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a number of bugfixes for the drivers/staging/ portion of the
kernel that have been reported recently.
Nothing major here, with maybe the exception of the ramster code can
now be built so it is enabled in the build again, and lots of memory
leaks that people like to have fixed on their systems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: fix mem leaks in __persistent_ram_init()
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
staging: iio: hmc5843: Fix crash in probe function.
staging/xgifb: fix display on XGI Volari Z11m cards
Staging: android: timed_gpio: Fix resource leak in timed_gpio_probe error paths
android: make persistent_ram based drivers depend on HAVE_MEMBLOCK
staging: iio: ak8975: Remove i2c client data corruption
staging: drm/omap: move where DMM driver is registered
staging: zsmalloc: fix memory leak
Staging: rts_pstor: off by one in for loop
staging: ozwpan: Added new maintainer for ozwpan
staging:rts_pstor:Avoid "Bad target number" message when probing driver
staging:rts_pstor:Fix possible panic by NULL pointer dereference
Staging: vt6655-6: check keysize before memcpy()
staging/media/as102: Don't call release_firmware() on uninitialized variable
staging:iio:core add missing increment of loop index in iio_map_array_unregister()
staging: ramster: unbreak my heart
staging/vme: Fix module parameters
staging: sep: Fix sign of error
Merge tag 'driver-core-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and kobject fixes from Greg KH:
"Here are some minor fixes for the driver core and kobjects that people
have reported recently.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: provide more diagnostic info for kobject_add_internal() failures
sysfs: handle 'parent deleted before child added'
sysfs: Prevent crash on unset sysfs group attributes
sysfs: Update the name hash for an entry after changing the namespace
drivers/base: fix compiler warning in SoC export driver - idr should be ida
drivers/base: Remove unneeded spin_lock_init call for soc_lock
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a fix for the recent irqdomain bug fixes from Grant Likely:
"I flubbed one patch in the last pull request which broke a format
string on 64 bit platforms. Here's the fix."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irq_domain: fix type mismatch in debugfs output format
projects / karo-tx-linux.git / log