This fixes a regression introduced by the new drm_update_vblank_count()
implementation in Linux 4.4:
Restrict the bump of the software vblank counter in drm_update_vblank_count()
to a safe maximum value of +1 whenever there is the possibility that
concurrent readers of vblank timestamps could be active at the moment,
as the current implementation of the timestamp caching and updating is
not safe against concurrent readers for calls to store_vblank() with a
bump of anything but +1. A bump != 1 would very likely return corrupted
timestamps to userspace, because the same slot in the cache could
be concurrently written by store_vblank() and read by one of those
readers in a non-atomic fashion and without the read-retry logic
detecting this collision.
Concurrent readers can exist while drm_update_vblank_count() is called
from the drm_vblank_off() or drm_vblank_on() functions or other non-vblank-
irq callers. However, all those calls are happening with the vbl_lock
locked thereby preventing a drm_vblank_get(), so the vblank refcount
can't increase while drm_update_vblank_count() is executing. Therefore
a zero vblank refcount during execution of that function signals that
is safe for arbitrary counter bumps if called from outside vblank irq,
whereas a non-zero count is not safe.
Whenever the function is called from vblank irq, we have to assume concurrent
readers could show up any time during its execution, even if the refcount
is currently zero, as vblank irqs are usually only enabled due to the
presence of readers, and because when it is called from vblank irq it
can't hold the vbl_lock to protect it from sudden bumps in vblank refcount.
Therefore also restrict bumps to +1 when the function is called from vblank
irq.
Such bumps of more than +1 can happen at other times than reenabling
vblank irqs, e.g., when regular vblank interrupts get delayed by more
than 1 frame due to long held locks, long irq off periods, realtime
preemption on RT kernels, or system management interrupts.
A better solution would be to rewrite the timestamp caching to use
full seqlocks to allow concurrent writes and reads for arbitrary
vblank counter increments.
v2: Add code comment that this is essentially a hack and should
be replaced by a full seqlock implementation for caching of
timestamps.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise if a kms driver calls into drm_vblank_off() more than once
before calling drm_vblank_on() again, the redundant calls to
vblank_disable_and_save() will call drm_update_vblank_count()
while hw vblank counters and vblank timestamping are in a undefined
state during modesets, dpms off etc.
At least with the legacy drm helpers it is not unusual to
get multiple calls to drm_vblank_off and drm_vblank_on, e.g.,
half a dozen calls to drm_vblank_off and two calls to drm_vblank_on
were observed on radeon-kms during dpms-off -> dpms-on transition.
We don't no-op calls from atomic modesetting drivers, as they
should do a proper job of tracking hw state.
Fixes large jumps of the software maintained vblank counter due to
the hardware vblank counter resetting to zero during dpms off or
modeset, e.g., if radeon-kms is modified to use drm_vblank_off/on
instead of drm_vblank_pre/post_modeset().
This fixes a regression caused by the changes made to
drm_update_vblank_count() in Linux 4.4.
v2: Don't no-op on atomic modesetting drivers, per suggestion
of Daniel Vetter.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a
result we skip assigning a DPLL to any DP MST ports, which makes link
training fail:
[ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well
[ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well
[ 1442.933957] [drm:intel_mst_pre_enable_dp] 0
[ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000
[ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0
[ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0
[ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000
[ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1
[ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1
[ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000
[ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2
…
[ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up
[ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting
After which the pipe state goes completely out of sync:
[ 70.075596] [drm:check_crtc_state] [CRTC:25]
[ 70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001)
[ 70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0)
[ 70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021)
[ 70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173)
[ 70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5)
[ 70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256)
[ 70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500)
And if you're especially lucky, it keeps going downhill:
On SKL+ plane scaling is mutually exclusive with color keying. The code
check for this, but during some refactoring the code got changed to
also reject primary plane windowing when color keying is used. There is
no such restriction in the hardware, so restore the original logic.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: 061e4b8d650a ("drm/i915: clean up atomic plane check functions, v2.") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452883613-28549-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 693bdc28a733dba68b86af295e7509812fec35d9) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
We need to set the DC FLUSH PIPE_CONTROL bit on Gen7+ to guarantee
that writes performed via the HDC are visible in memory. Fixes an
intermittent failure in a Piglit test that writes to a BO from a
shader using GL atomic counters (implemented as HDC untyped atomics)
and then expects the memory to read back the same value after mapping
it on the CPU.
gmbus also needs the power domain infrastructure right from the start,
since as soon as we register the i2c controllers someone can use them.
v2: Adjust cleanup paths too (Chris).
v3: Rebase onto -nightly (totally bogus tree I had lying around) and
also move dpio init head (Ville).
v4: Ville instead suggested to move gmbus setup later in the sequence,
since it's only needed by the modeset code.
v5: Move even close to the actual user, right next to the comment that
states where we really need gmbus (and interrupts!).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Meelis Roos <mroos@linux.ee> Cc: Chris Wilson <chris@chris-wilson.co.uk> Fixes: ac9b8236551d ("drm/i915: Introduce a gmbus power domain")
References: http://www.spinics.net/lists/intel-gfx/msg83075.html Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452682528-19437-1-git-send-email-daniel.vetter@ffwll.ch Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes reprobing of display connectors on resume. After some
talking with danvet on IRC, I learned that calling
drm_helper_hpd_irq_event() does actually trigger a full reprobe of each
connector's status. It turns out this is the actual reason reprobing on
resume hasn't been working (this was observed on a T440s):
- We call hpd_init()
- We check each connector for a couple of things before marking
connector->polled with DRM_CONNECTOR_POLL_HPD, one of which is an
active encoder. Of course, a disconnected port won't have an
active encoder, so we don't add the flag to any of the
connectors.
- We call drm_helper_hpd_irq_event()
- drm_helper_irq_event() checks each connector for the
DRM_CONNECTOR_POLL_HPD flag. The only one that has it is eDP-1,
so we skip reprobing each connector except that one.
In addition, we also now avoid setting connector->polled to
DRM_CONNECTOR_POLL_HPD for MST connectors, since their reprobing is
handled by the mst helpers. This is probably what was originally
intended to happen here.
Changes since V1:
* Use the explanation of the issue as the commit message instead
* Change the title of the commit, since this does more then just stop a
check for an encoder now
* Add "Fixes" line for the patch that introduced this regression
* Don't enable DRM_CONNECTOR_POLL_HPD for mst connectors
Changes since V2:
* Put patch changelog above Signed-off-by
* Follow Daniel Vetter's suggestion for making the code here a bit more
legible
Following a GPU reset, we may leave the context in a poorly defined
state, and reloading from that context will leave the GPU flummoxed. For
secondary contexts, this will lead to that context being banned - but
currently it is also causing the default context to become banned,
leading to turmoil in the shared state.
which quietly introduced the removal of the MI_RESTORE_INHIBIT on the
default context.
v2: Mark the global default context as uninitialized on GPU reset so
that the context-local workarounds are reloaded upon re-enabling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448630935-27377-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: This seems to fix a gpu hand on after the first resume,
resulting in any future suspend operation failing with -EIO because
the gpu seems to be in a funky state. Somehow this patch fixes that.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 42f1cae8c079bcceb3cff079fddc3ff8852c788f) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly setup the DFS divider for DP audio for DCE4.1.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move encoding of DFS (digital frequency synthesizer) divider into a
separate function and improve calculation precision.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation for the fixes in the following patches.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware is LE. Need to properly byteswap some of the fields
so they are interpreted correctly by the driver on BE systems.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
eoffset is sometimes treated as the last address inside the address
range, and sometimes as the first address outside the range. This
was resulting in errors when a test filled up the entire address
space. Make it consistent to always be the last address within the
range. Also fixed related errors when checking the VA limit and in
radeon_vm_fence_pts.
Signed-off-by: Felix.Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to properly deallocate port payload
after downstream branch get unplugged.
In order to do this unplugged MST topology should
be preserved, to find first alive port on path to
unplugged MST topology, and send payload deallocation
request to branch device of found port.
For this mstb and port kref's are used in reversed
order to track when port and branch memory could be
freed.
Added additional functions to find appropriate mstb
as described above.
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous implementation does not handle case below: boot up one MST branch
to DP connector of ASIC. After boot up, hot plug 2nd MST branch to DP output
of 1st MST, GUID is not created for 2nd MST branch. When downstream port of
2nd MST branch send upstream request, it fails because 2nd MST branch GUID
is not available.
New Implementation: only create GUID for MST branch and save it within Branch.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_fixp_from_fraction allows us to create a fixed point directly
from a fraction, rather than creating fixed point values and dividing
later. This avoids overflow of our 64 bit value for large numbers.
drm_fixp2int_ceil allows us to return the ceiling of our fixed point
value.
[airlied: squash Jordan's fix]
32-bit-build-fix: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case broadcast message received in UP request,
RAD cannot be used to identify message originator.
Message should be parsed, originator should be found
by GUID from parsed message.
Also reply with broadcast in case broadcast message
received (for now it is always broadcast)
Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the display resume path, move the calls to drm_vblank_on()
after the point when the display engine is running again.
Since changes were made to drm_update_vblank_count() in Linux 4.4+
to emulate hw vblank counters via vblank timestamping, the function
drm_vblank_on() now needs working high precision vblank timestamping
and therefore working scanout position queries at time of call.
These don't work before the display engine gets restarted, causing
miscalculation of vblank counter increments and thereby large forward
jumps in vblank count at display resume. These jumps can cause client
hangs on resume, or desktop hangs in the case of composited desktops.
Fix this Linux 4.4 regression by reordering calls accordingly.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a port of the same fix for radeon-kms in the
patch "drm/radeon: Don't hang in radeon_flip_work_func
on disabled crtc. (v2)"
Limit the amount of time amdgpu_flip_work_func can
delay programming a page flip, by both limiting the
maximum amount of time per wait cycle and the maximum
number of wait cycles. Continue the flip if the limit
is exceeded, even if that may result in a visual or
timing glitch.
This is to prevent a hang of page flips, as reported
in fdo bug #93746: Disconnecting a DisplayPort display
in parallel to a kms pageflip getting queued can cause
the following hang of page flips and thereby an unusable
desktop:
2. Hotunplug of display causes the driver to DPMS OFF
the unplugged display. Display engine shuts down,
scanout no longer moves, but stays at its resting
position at start line of vblank.
3. amdgpu_flip_work_func executes while crtc is off, and
due to the non-moving scanout position, the new flip
delay code introduced into Linux 4.4 by
commit 8e36f9d33c13 ("drm/amdgpu: Fixup hw vblank counter/ts..")
enters an infinite wait loop.
4. After reconnecting the display, the pageflip continues
to hang in 3. and the display doesn't update its view
of the desktop.
This patch fixes the Linux 4.4 regression from fdo bug #93746
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we could try to evict overlapping userptr BOs in get_user_pages(),
leading to a possible circular locking dependency.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An arbitrary amount of time can pass between spin_unlock and
fence_wait_any_timeout, so we need to ensure that nobody frees the
fences from under us.
A stress test (rapidly starting and killing hundreds of glxgears
instances) ran into a deadlock in fence_wait_any_timeout after
about an hour, and this race condition appears to be a plausible
cause.
v2: agd: rebase on upstream
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the topaz golden settings into the gmc7 module.
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ken Wang >Qingqing.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
v2: make logic more readable as suggested by Michel
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1) Reviewed-by: Rex Zhu <Rex.Zhu@amd.com> (v1) Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to make sure smu buffers are pinned on resume. This
matches what Fiji does.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
eaddr is sometimes treated as the last address inside the address
range, and sometimes as the first address outside the range. This
was resulting in errors when a test filled up the entire address
space. Make it consistent to always be the last address within the
range.
Signed-off-by: Felix.Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>. Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the framebuffer is a vmwgfx dma buffer and a proxy surface is
created, the vmw_kms_update_proxy() function requires that the proxy
surface width and the framebuffer pitch are compatible, otherwise
display corruption occurs as seen in gnome-shell/native with software
3D. Since the framebuffer pitch is determined by user-space, allocate
a proxy surface the width of which is based on the framebuffer pitch
rather than on the framebuffer width.
Reported-by: Raphael Hertzog <buxy@kali.org> Tested-by: Mati Aharoni <muts@kali.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_SMP=n and CONFIG_DEBUG_SPINLOCK=y the vmwgfx kernel module
would unconditionally throw a bug when checking for a held spinlock
in the command buffer code. Fix this by using a lockdep check.
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@i-love-sakura.ne.jp> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASan detected a use-after-free error in virtio-pci remove code. In
virtio_pci_remove(), vp_dev is still used after being freed in
unregister_virtio_device() (in virtio_pci_release_dev() more
precisely).
To fix, keep a reference until cleanup is done.
Fixes: 63bd62a08ca4 ("virtio_pci: defer kfree until release callback") Reported-by: Jerome Marchand <jmarchan@redhat.com> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In balloon_page_dequeue, pages_lock should cover the loop
(ie, list_for_each_entry_safe). Otherwise, the cursor page could
be isolated by compaction and then list_del by isolation could
poison the page->lru.{prev,next} so the loop finally could
access wrong address like this. This patch fixes the bug.
Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During my compaction-related stuff, I encountered a bug
with ballooning.
With repeated inflating and deflating cycle, guest memory(
ie, cat /proc/meminfo | grep MemTotal) is decreased and
couldn't be recovered.
The reason is balloon_lock doesn't cover release_pages_balloon
so struct virtio_balloon fields could be overwritten by race
of fill_balloon(e,g, vb->*pfns could be critical).
This patch fixes it in my test.
Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the below build error:
drivers/regulator/mt6311-regulator.c:111: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Henry Chen <henryc.chen@mediatek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is allowed to enable/disable clocks from interrupts, so common Exynos
ARM clock management code for CPUfreq should use 'irqsave' version of
spin_lock calls to avoid potential deadlock caused by spin_lock recursion.
The same spin_lock is used by gate/mux clocks during enable/disable calls.
This deadlock, can be reproduced by enabling CPUfreq (ondemand or
userspace) and decoding video with s5p-mfc driver.
Relevant stack trace:
[ 5928.061534] BUG: spinlock recursion on CPU#0, bash/1252
[ 5928.061609] lock: 0xee80454c, .magic: dead4ead, .owner: bash/1252, .owner_cpu: 0
[ 5928.068586] CPU: 0 PID: 1252 Comm: bash Tainted: G W 4.4.0-rc4-00001-g447a7fd #678
[ 5928.077260] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 5928.083359] [<c00153dc>] (unwind_backtrace) from [<c00121b4>] (show_stack+0x10/0x14)
[ 5928.091072] [<c00121b4>] (show_stack) from [<c0213e28>] (dump_stack+0x68/0xb8)
[ 5928.098275] [<c0213e28>] (dump_stack) from [<c005c1ec>] (do_raw_spin_lock+0x184/0x1ac)
[ 5928.106177] [<c005c1ec>] (do_raw_spin_lock) from [<c05cfa98>] (_raw_spin_lock_irqsave+0x20/0x28)
[ 5928.114943] [<c05cfa98>] (_raw_spin_lock_irqsave) from [<c0468698>] (clk_gate_endisable+0x24/0x98)
[ 5928.123882] [<c0468698>] (clk_gate_endisable) from [<c0464d40>] (clk_core_disable+0x60/0x84)
[ 5928.132299] [<c0464d40>] (clk_core_disable) from [<c0465e00>] (clk_disable+0x24/0x30)
[ 5928.140117] [<c0465e00>] (clk_disable) from [<c03f3b80>] (s5p_mfc_handle_frame+0x254/0x860)
[ 5928.148445] [<c03f3b80>] (s5p_mfc_handle_frame) from [<c03f4b34>] (s5p_mfc_irq+0x890/0xa24)
[ 5928.156778] [<c03f4b34>] (s5p_mfc_irq) from [<c00627bc>] (handle_irq_event_percpu+0x50/0x14c)
[ 5928.165283] [<c00627bc>] (handle_irq_event_percpu) from [<c00628f0>] (handle_irq_event+0x38/0x5c)
[ 5928.174143] [<c00628f0>] (handle_irq_event) from [<c0065864>] (handle_fasteoi_irq+0xdc/0x1a4)
[ 5928.182645] [<c0065864>] (handle_fasteoi_irq) from [<c0062090>] (generic_handle_irq+0x18/0x28)
[ 5928.191236] [<c0062090>] (generic_handle_irq) from [<c00621a4>] (__handle_domain_irq+0x6c/0xdc)
[ 5928.199917] [<c00621a4>] (__handle_domain_irq) from [<c0009470>] (gic_handle_irq+0x4c/0x98)
[ 5928.208249] [<c0009470>] (gic_handle_irq) from [<c0012c54>] (__irq_svc+0x54/0x90)
[ 5928.215709] Exception stack(0xeddb5cb8 to 0xeddb5d00)
[ 5928.220745] 5ca0: ee80454cfaddfadc
[ 5928.228906] 5cc0: 0000000001000001ee831ce0f8114200ee807c000113052000000403eddb5d84
[ 5928.237063] 5ce0: ee807c482faf0800ee807c0ceddb5d08c046b618c046b63420000053ffffffff
[ 5928.245225] [<c0012c54>] (__irq_svc) from [<c046b634>] (exynos_cpuclk_notifier_cb+0x170/0x270)
[ 5928.253823] [<c046b634>] (exynos_cpuclk_notifier_cb) from [<c003cb58>] (notifier_call_chain+0x44/0x84)
[ 5928.263106] [<c003cb58>] (notifier_call_chain) from [<c003ccd4>] (__srcu_notifier_call_chain+0x6c/0x9c)
[ 5928.272480] [<c003ccd4>] (__srcu_notifier_call_chain) from [<c003cd1c>] (srcu_notifier_call_chain+0x18/0x20)
[ 5928.282288] [<c003cd1c>] (srcu_notifier_call_chain) from [<c0464ed0>] (__clk_notify+0x6c/0x74)
[ 5928.290881] [<c0464ed0>] (__clk_notify) from [<c0465388>] (clk_propagate_rate_change+0xa0/0xac)
[ 5928.299561] [<c0465388>] (clk_propagate_rate_change) from [<c0465378>] (clk_propagate_rate_change+0x90/0xac)
[ 5928.309370] [<c0465378>] (clk_propagate_rate_change) from [<c04666fc>] (clk_core_set_rate_nolock+0x64/0xa8)
[ 5928.319091] [<c04666fc>] (clk_core_set_rate_nolock) from [<c0466760>] (clk_set_rate+0x20/0x30)
[ 5928.327686] [<c0466760>] (clk_set_rate) from [<c0428c70>] (set_target+0xe8/0x23c)
[ 5928.335152] [<c0428c70>] (set_target) from [<c04244d0>] (__cpufreq_driver_target+0x184/0x29c)
[ 5928.343655] [<c04244d0>] (__cpufreq_driver_target) from [<c0427128>] (cpufreq_set+0x44/0x64)
[ 5928.352074] [<c0427128>] (cpufreq_set) from [<c0423948>] (store_scaling_setspeed+0x5c/0x74)
[ 5928.360407] [<c0423948>] (store_scaling_setspeed) from [<c04238d0>] (store+0x7c/0x98)
[ 5928.368221] [<c04238d0>] (store) from [<c0132540>] (sysfs_kf_write+0x44/0x48)
[ 5928.375338] [<c0132540>] (sysfs_kf_write) from [<c0131b9c>] (kernfs_fop_write+0xb8/0x1bc)
[ 5928.383496] [<c0131b9c>] (kernfs_fop_write) from [<c00d71f8>] (__vfs_write+0x2c/0xd4)
[ 5928.391308] [<c00d71f8>] (__vfs_write) from [<c00d7de8>] (vfs_write+0xa0/0x144)
[ 5928.398598] [<c00d7de8>] (vfs_write) from [<c00d8048>] (SyS_write+0x44/0x84)
[ 5928.405631] [<c00d8048>] (SyS_write) from [<c000f540>] (ret_fast_syscall+0x0/0x3c)
When writing a value to config space, cxl_pcie_write_config() calls
cxl_pcie_config_info() to obtain a mask and shift value, shifts the new
value accordingly, then uses the mask to combine the shifted value with the
existing value at the address as part of a read-modify-write pattern.
Currently, we use a logical OR operator rather than a bitwise OR operator,
which means any use of this function results in an incorrect value being
written. Replace the logical OR operator with a bitwise OR operator so the
value is written correctly.
Reported-by: Michael Ellerman <mpe@ellerman.id.au> Fixes: 6f7f0b3df6d4 ("cxl: Add AFU virtual PHB and kernel API") Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by sys_personality has type "long int".
It is saved to a variable of type "int", which is not a problem
yet because the type of task_struct->pesonality is "unsigned int".
The problem is the sign extension from "int" to "long int"
that happens on return from sys_sparc64_personality.
For example, a userspace call personality((unsigned) -EINVAL) will
result to any subsequent personality call, including absolutely
harmless read-only personality(0xffffffff) call, failing with
errno set to EINVAL.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I get the splat below when modprobing/rmmoding EDAC drivers. It happens
because bus->name is invalid after bus_unregister() has run. The Code: section
below corresponds to:
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
Since commit 4c21b8fd8f14 ("MIPS: seccomp: Handle indirect system calls
(o32)"), syscall_get_arguments() attempts to handle o32 indirect syscall
arguments by incrementing both the start argument number and the number
of arguments to fetch. However only the start argument number needs to
be incremented. The number of arguments does not change, they're just
shifted up by one, and in fact the output array is provided by the
caller and is likely only n entries long, so reading more arguments
overflows the output buffer.
In the case of seccomp, this results in it fetching 7 arguments starting
at the 2nd one, which overflows the unsigned long args[6] in
populate_seccomp_data(). This clobbers the $s0 register from
syscall_trace_enter() which __seccomp_phase1_filter() saved onto the
stack, into which syscall_trace_enter() had placed its syscall number
argument. This caused Chromium to crash.
Credit goes to Milko for tracking it down as far as $s0 being clobbered.
Commit be0c37c985eddc4 (MIPS: Rearrange PTE bits into fixed positions.)
defines fixed PTE bits for MIPS R2. Then, commit d7b631419b3d230a4d383
(MIPS: pgtable-bits: Fix XPA damage to R6 definitions.) adds the MIPS
R6 definitions in the same way as MIPS R2. But some R6 #ifdefs in the
later commit are missing, so in this patch I fix that.
This patch is borrowed from x86 hpet driver and explaind below:
Due to the overly intelligent design of HPETs, we need to workaround
the problem that the compare value which we write is already behind
the actual counter value at the point where the value hits the real
compare register. This happens for two reasons:
1) We read out the counter, add the delta and write the result to the
compare register. When a NMI hits between the read out and the write
then the counter can be ahead of the event already.
2) The write to the compare register is delayed by up to two HPET
cycles in AMD chipsets.
We can work around this by reading back the compare register to make
sure that the written value has hit the hardware. But that is bad
performance wise for the normal case where the event is far enough in
the future.
As we already know that the write can be delayed by up to two cycles
we can avoid the read back of the compare register completely if we
make the decision whether the delta has elapsed already or not based
on the following calculation:
cmp = event - actual_count;
If cmp is less than 64 HPET clock cycles, then we decide that the event
has happened already and return -ETIME. That covers the above #1 and #2
problems which would cause a wait for HPET wraparound (~306 seconds).
When Core-0 handle SMP_ASK_C0COUNT IPI, we should make other cores to
see the result as soon as possible (especially when Store-Fill-Buffer
is enabled). Otherwise, C0_Count syncronization makes no sense.
BTW, array is more suitable than per-cpu variable for syncronization,
and there is a corner case should be avoid: C0_Count of Core-0 can be
really 0.
It was originally sent in an earlier revision of the pfn_t patchset.
Besides being broken, the warning is also fixed by PFN_FLAGS_MASK
casting the PAGE_MASK to an unsigned long.
Reported-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: linux-kernel@vger.kernel.org Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/12182/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1e75fa8 "time: Condense timekeeper.xtime into xtime_sec" replaced a call to
clocksource_cyc2ns() from timekeeping_get_ns() with an open-coded version
of the same logic to avoid keeping a semi-redundant struct timespec
in struct timekeeper.
However, the commit also introduced a subtle semantic change - where
clocksource_cyc2ns() uses purely unsigned math, the new version introduces
a signed temporary, meaning that if (delta * tk->mult) has a 63-bit
overflow the following shift will still give a negative result. The
choice of 'maxsec' in __clocksource_updatefreq_scale() means this will
generally happen if there's a ~10 minute pause in examining the
clocksource.
This can be triggered on a powerpc KVM guest by stopping it from qemu for
a bit over 10 minutes. After resuming time has jumped backwards several
minutes causing numerous problems (jiffies does not advance, msleep()s can
be extended by minutes..). It doesn't happen on x86 KVM guests, because
the guest TSC is effectively frozen while the guest is stopped, which is
not the case for the powerpc timebase.
Obviously an unsigned (64 bit) overflow will only take twice as long as a
signed, 63-bit overflow. I don't know the time code well enough to know
if that will still cause incorrect calculations, or if a 64-bit overflow
is avoided elsewhere.
Still, an incorrect forwards clock adjustment will cause less trouble than
time going backwards. So, this patch removes the potential for
intermediate signed overflow.
Suggested-by: Laurent Vivier <lvivier@redhat.com> Tested-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes incorrect handling of the 6lowpan packets that contain
uncompressed IPv6 header.
RFC4944 specifies a special dispatch for 6lowpan to carry uncompressed
IPv6 header. This dispatch (1 byte long) has to be removed during
reception and skb data pointer has to be moved. To correctly point in
the beginning of the IPv6 header the dispatch byte has to be pulled off
before packet can be processed by netif_rx_in().
Test scenario: IPv6 packets are not correctly interpreted by the network
layer when IPv6 header is not compressed (e.g. ICMPv6 Echo Reply is not
propagated correctly to the ICMPv6 layer because the extra byte will make
the header look corrupted).
The first modification fixes the NULL pointer dereference error by
assigning dev to the local_skb in order to set a valid net_device before
processing the skb by netif_rx_ni().
Scenario #2:
============
Bluetooth 6lowpan receives an UDP compressed message which needs further
decompression by nhc_udp. The following error occurs:
Null pointer dereference error #2 crash log:
[ 63.295149] BUG: unable to handle kernel NULL pointer dereference at 0000000000000840
[ 63.295931] IP: [<ffffffffc0559540>] udp_uncompress+0x320/0x626
[nhc_udp]
The second modification fixes the NULL pointer dereference error by
assigning dev to the local_skb in the case of a udp compressed packet.
The 6lowpan udp_uncompress function expects that the net_device is set in
the skb when checking lltype.
The commit cad20c278085d893ebd616cd20c0747a8e9d53c7 was supposed to
fix handling of devices first using public addresses and then
switching to RPAs after pairing. Unfortunately it missed a couple of
key places in the code.
1. When evaluating which devices should be removed from the existing
white list we also need to consider whether we have an IRK for them or
not, i.e. a call to hci_find_irk_by_addr() is needed.
2. In smp_notify_keys() we should not be requiring the knowledge of
the RPA, but should simply keep the IRK around if the other conditions
require it.
All LE connections are now triggered through a preceding passive scan
and waiting for a connectable advertising report. This means we've got
the best possible guarantee that the device is within range and should
be able to request the controller to perform continuous scanning. This
way we minimize the risk that we miss out on any advertising packets.
Currently we have two policies for deciding when to signal the host:
One based on the ring buffer state and the other based on what the
VMBUS client driver wants to do. Consider the case when the client
wants to explicitly control when to signal the host. In this case,
if the client were to defer signaling, we will not be able to signal
the host subsequently when the client does want to signal since the
ring buffer state will prevent the signaling. Implement logic to
have only one signaling policy in force for a given channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Tested-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().
To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().
Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe71953 ("mmc: pxamci: fix read-only gpio detection polarity") Reported-by: Andrea Adami <andrea.adami@gmail.com> Tested-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
commit 4956e10903fd ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Fixes: 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik...") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.
This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.
With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
Commit cc4f414c885c ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode. While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: Wenkai Du <wenkai.du@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor
table to define DMA scatter-gather. Each desciptor can specify
a data length up to 65536 bytes, however the length field is
only 16-bits so zero means 65536. Consequently, putting zero
when the size is zero must not be allowed. This patch fixes
one case where zero data length could be set inadvertently.
The problem happens because unaligned data gets split and the
code did not consider that the remaining aligned portion might
be zero length. That case really only happens for SDIO because
SD and eMMC cards transfer blocks that are invariably sector-
aligned. For SDIO, access to function registers is done by
data transfer (CMD53) when the register is bigger than 1 byte.
Generally registers are 4 bytes but 2-byte registers are possible.
So DMA of 4 bytes or less can happen. When 32-bit DMA is used,
the data alignment must be 4, so 4-byte transfers won't casue a
problem, but a 2-byte transfer could. However with the introduction
of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes,
so all 4-byte transfers not on 8-byte boundaries get "split" into
a 4-byte chunk and a 0-byte chunk, thereby hitting the bug.
In fact, a closer look at the SDHCI specs indicates that only the
descriptor table requires 8-byte alignment for 64-bit DMA. That
will be dealt with in a separate patch, but the potential for a
2-byte access remains, so this fix is needed anyway.
Commit bb08a7d489bd ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
clockevents_exchange_device is calling clockevents_shutdown() on the new
clockenvents device but it may have never been enabled in the first place.
This results in the tcb clock being disabled without being enabled first:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:680 clk_disable+0x28/0x34()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0+ #6
Hardware name: Atmel AT91SAM9
[<c000f2b8>] (unwind_backtrace) from [<c000d01c>] (show_stack+0x10/0x14)
[<c000d01c>] (show_stack) from [<c00172f0>] (warn_slowpath_common+0x78/0xa0)
[<c00172f0>] (warn_slowpath_common) from [<c00173a8>] (warn_slowpath_null+0x18/0x20)
[<c00173a8>] (warn_slowpath_null) from [<c0361528>] (clk_disable+0x28/0x34)
[<c0361528>] (clk_disable) from [<c034d560>] (tc_shutdown+0x38/0x4c)
[<c034d560>] (tc_shutdown) from [<c0059ad4>] (clockevents_switch_state+0x38/0x6c)
[<c0059ad4>] (clockevents_switch_state) from [<c0059b18>] (clockevents_shutdown+0x10/0x24)
[<c0059b18>] (clockevents_shutdown) from [<c005a458>] (tick_check_new_device+0x84/0xac)
[<c005a458>] (tick_check_new_device) from [<c0059660>] (clockevents_register_device+0x7c/0x108)
[<c0059660>] (clockevents_register_device) from [<c06b5a68>] (tcb_clksrc_init+0x390/0x3e8)
[<c06b5a68>] (tcb_clksrc_init) from [<c00097cc>] (do_one_initcall+0x114/0x1d4)
[<c00097cc>] (do_one_initcall) from [<c069bd54>] (kernel_init_freeable+0xfc/0x1b8)
[<c069bd54>] (kernel_init_freeable) from [<c04c3818>] (kernel_init+0x8/0xe0)
[<c04c3818>] (kernel_init) from [<c000a410>] (ret_from_fork+0x14/0x24)
---[ end trace 0000000000000001 ]---
Check what state we were in before trying to disable the clock.
Fixes: cf4541c101ea ("clockevents/drivers/tcb_clksrc: Migrate to new 'set-state' interface") Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Link: http://lkml.kernel.org/r/1452854061-30370-1-git-send-email-alexandre.belloni@free-electrons.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log