Olof Johansson [Fri, 6 Feb 2015 08:03:28 +0000 (00:03 -0800)]
Merge tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:
Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
ARM: dts: rockchip: add rk3288 watchdog clock
clk: rockchip: add id for watchdog pclk on rk3288
clk: rockchip: add clock IDs for the PVTM clocks
clk: rockchip: add clock ID for usbphy480m_src
Heiko Stuebner [Wed, 28 Jan 2015 16:23:10 +0000 (17:23 +0100)]
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Heiko Stuebner [Wed, 28 Jan 2015 11:27:16 +0000 (12:27 +0100)]
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.
This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Heiko Stuebner [Thu, 29 Jan 2015 21:35:47 +0000 (22:35 +0100)]
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Heiko Stuebner [Thu, 29 Jan 2015 21:21:01 +0000 (22:21 +0100)]
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Olof Johansson [Thu, 29 Jan 2015 22:03:28 +0000 (14:03 -0800)]
Merge tag 'zynq-dt-for-3.20' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "Zync DT for v3.20" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.20
- Add USB chipidea driver to DT
- Add pincontrol
- Add aliases node
- Fix WDT node
* tag 'zynq-dt-for-3.20' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: Add aliases node
ARM: zynq: DT: Fix binding for cadence WDT
ARM: zynq: DT: Add pinctrl information to USB nodes
ARM: zynq: DT: Remove bogus value from 'bias-disable' property
ARM: zynq: DT: Add pinctrl information
ARM: zynq: DT: Add USB to device tree
Olof Johansson [Thu, 29 Jan 2015 21:57:19 +0000 (13:57 -0800)]
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Olof Johansson [Thu, 29 Jan 2015 21:54:26 +0000 (13:54 -0800)]
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
ARM: dts: Add regulator-haptic node for exynos3250-monk
ARM: dts: Add regulator-haptic node for exynos3250-rinato
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
ARM: dts: convert to generic power domain bindings for exynos DT
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.
So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:
ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)
Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Kukjin Kim <kgene@kernel.org>
Olof Johansson [Wed, 28 Jan 2015 00:24:08 +0000 (16:24 -0800)]
Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:
Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
dt-bindings: add vendor prefix and root compatible property for Rockchip boards
ARM: dts: rockchip: Add rockchip timer node for rk3288
ARM: dts: rockchip: add rk3288 hdmi nodes
ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Bhupesh Sharma [Sat, 24 Jan 2015 21:12:51 +0000 (02:42 +0530)]
Documentation: DT: Add entry for FSL Management Complex
This patch adds a devicetree binding documentation for FSL's
Management Complex.
Management Complex is a hardware resource manager that manages
specialized hardware objects used in network-oriented packet
processing applications
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Bhupesh Sharma [Sat, 24 Jan 2015 21:12:49 +0000 (02:42 +0530)]
Documentation: DT: Add bindings for FSL NS16550A UART
This patch addss the device-tree documentation for Freescale's
NS16550 UART (also called DUART).
There is a specific errata fix required in FSL NS16550 UART
which ensures that an random interrupt storm is not observed when
a break is provided as an input to the UART.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 27 Jan 2015 04:26:34 +0000 (20:26 -0800)]
Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #2" from Nicolas Ferre:
Second DT batch for 3.20:
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: Add ac97 device node
dt: atmel_ac97c: Add device tree documentation
ARM: at91: at91sam9n12ek/dt: use dt ids for wm8904
ARM: at91: sama5d3xek/dt: use dt ids for wm8904
ARM: at91: sama5d4: dts: change the nand compatible string
ARM: at91/dt: sama5d4: add pioD controller
ARM: at91/dt: disable pull-up on vbus-gpio (PB16) to reduce power consumption
Olof Johansson [Tue, 27 Jan 2015 04:24:47 +0000 (20:24 -0800)]
Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
ARM: dts: sun4i: Add Hyundau A7HD board
ARM: dts: sun4i: Add Marsboard A10 board
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
ARM: dts: sun9i: Add mmc config clock nodes
ARM: dts: sunxi: Add missing mdio label
ARM: dts: sun5i: Add mk802_a10s board
ARM: dts: sun4i: Add mk802ii board
ARM: dts: sun4i: Add mk802 board
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
ARM: dts: sun7i: Add dts file for Bananapro board
ARM: sun6i: Enable ARM arch timers
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
...
Olof Johansson [Tue, 27 Jan 2015 02:41:45 +0000 (18:41 -0800)]
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.20" from Kukjin Kim:
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Configure regulators for suspend on exynos Peach boards
ARM: dts: Set Peach boards USB WebCam regulators to always on
ARM: dts: Add lid GPIO key device node for Peach boards
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
Documentation: dt-bindings: add exynos-chipid binding information
ARM: dts: add Panel device support for exynos3250-rinato
ARM: dts: add fimd device support for exynos3250-rinato
ARM: dts: use macro in gpio keys for exynos3250 boards
ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
ARM: dts: Enable USB node for exynos3250-monk
ARM: dts: Enable USB node for exynos3250-rinato
ARM: dts: Add hsotg node for exynos3250
ARM: dts: Add exynos_usbphy node for exynos3250
ARM: dts: Add dts file for Odroid XU3 board
Signed-off-by: Alexander Morozov <linux@meltdown.ru> Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
FUKAUMI Naoki [Sun, 25 Jan 2015 12:39:35 +0000 (21:39 +0900)]
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
This adds support for Firefly-RK3288, Rockchip RK3288 based development
boards made by Firefly.
There are 2 dts for 2 versions of the board. rk3288-firefly-beta.dts is
for the beta version, rk3288-firefly.dts is for the mass production version.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[removed gmac reference, due to the gmac node going through the net-tree] Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Daniel Lezcano [Sun, 25 Jan 2015 09:42:59 +0000 (10:42 +0100)]
ARM: dts: rockchip: Add rockchip timer node for rk3288
The rk3288 board uses the architected timers and these ones are shutdown when
the cpu is powered down. There is a need of a broadcast timer in this case to
ensure proper wakeup when the cpus are in sleep mode and a timer expires.
Add the timer node for the broadcast timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Vishnu Patekar [Sun, 25 Jan 2015 13:40:08 +0000 (19:10 +0530)]
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Marek Szyprowski [Sat, 24 Jan 2015 04:08:09 +0000 (13:08 +0900)]
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
Marek Szyprowski [Sat, 24 Jan 2015 04:12:03 +0000 (13:12 +0900)]
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
All currently supported boards use hsotg/dwc2 controller in device
('peripheral') mode, so add property which sets correct operation mode.
This patch fixes support in recent changes in dwc2 driver, which added
support for dual-role devices.
Suggested-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene@kernel.org>
Marek Szyprowski [Sat, 24 Jan 2015 04:16:15 +0000 (13:16 +0900)]
ARM: dts: convert to generic power domain bindings for exynos DT
This patch replaces all custom samsung,power-domain dt
properties with generic power domain bindings and updates
documentation Samsung's devices referring to old binding.
Suggested-by: Kevin Hilman <khilman@kernel.org> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[javier.martinez@collabora.co.uk: tested on the Exynos5800 Peach Pi Chromebook] Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
Olof Johansson [Fri, 23 Jan 2015 22:51:41 +0000 (14:51 -0800)]
Merge tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v3.20" from Thierry Reding:
A couple of unit addresses fixes in device trees, addition of microphone
detection on Chromebook 13 and a vendor prefix update.
* tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update isl29028 compatible string to use isil vendor prefix
ARM: tegra: Fix unit address for Cortex-A9 TWD timer
ARM: dts: tegra20: fix GR3D, DSI unit and reg base addresses
ARM: tegra: Enable the mic-detect gpio on Acer Chromebook 13
Olof Johansson [Fri, 23 Jan 2015 22:44:16 +0000 (14:44 -0800)]
Merge tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Olof Johansson [Fri, 23 Jan 2015 22:17:15 +0000 (14:17 -0800)]
Merge tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu/dt #2" from Andrew Lunn:
Second set of dt patches for mvebu for v3.20.
* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
Olof Johansson [Fri, 23 Jan 2015 21:58:01 +0000 (13:58 -0800)]
Merge tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.20" from Hauke Mehrtens:
bcm5301x-dt-2015-01-20: ARM: BCM5301X: dts updates for 3.20
* tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-900DHP
ARM: BCM5301X: Add LEDs for Buffalo devices
ARM: BCM5301X: Drop unused poll-interval from gpio-keys
ARM: BCM5301X: Add DT for Luxul XWC-1000
Hans de Goede [Fri, 23 Jan 2015 15:39:23 +0000 (16:39 +0100)]
ARM: dts: sun4i: Add Hyundau A7HD board
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PioD controller was not described in the device tree since we don't use
it. As pinctrl-at91 allows disabled gpio controllers in the device
tree, we can add it to complete the device description.
Andy Yan [Tue, 4 Nov 2014 05:13:14 +0000 (13:13 +0800)]
ARM: dts: rockchip: add rk3288 hdmi nodes
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Signed-off-by: Yakir Yang <ykk@rock-chips.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Tested-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Olof Johansson [Thu, 22 Jan 2015 01:03:01 +0000 (17:03 -0800)]
Merge tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/dt
Merge "qcom DT changes for v3.20" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.20
* Correct IPQ8064 tlmm interrupt
* Add Support for SD Card Detect for ifc6410 board
* tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
ARM: dts: qcom: Add Support for SD Card Detect for ifc6410 board
Olof Johansson [Thu, 22 Jan 2015 01:00:47 +0000 (17:00 -0800)]
Merge tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v3.20" from Simon
Horman:
* Support Renesas memory controllers
* Add SRC interrupt number on r8a779~ and r8a7791 SoCs
* Fix MSTP8 input clocks on r8a7791 SoC
* Add PM domain support to r8a7740
* Add DT bindings for the R-Mobile System Controller
* Use Add sh73a0-specific FSI2 compatible property
* tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PM / Domains: R-Mobile SYSC: Document SH-Mobile AG5 (sh73a0) binding
ARM: shmobile: sh73a0 dtsi: Add memory-controller nodes
ARM: shmobile: r8a7740 dtsi: Add memory-controller node
ARM: shmobile: r8a73a4 dtsi: Add memory-controller nodes
ARM: shmobile: Add DT bindings for Renesas memory controllers
ARM: shmobile: r8a7791: add SRC interrupt number on DTSI
ARM: shmobile: r8a7790: add SRC interrupt number on DTSI
ARM: shmobile: r8a7791: fix MSTP8 input clocks
ARM: shmobile: r8a7740 dtsi: Add PM domain support
PM / Domains: Add DT bindings for the R-Mobile System Controller
ARM: shmobile: sh73a0 dtsi: Add SoC-specific FSI2 compatible property
Paul Bolle [Mon, 19 Jan 2015 19:40:25 +0000 (20:40 +0100)]
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
The Kconfig symbol DEBUG_MVEBU_UART_ALTERNATE was renamed to
DEBUG_MVEBU_UART0_ALTERNATE. And the symbol DEBUG_MVEBU_UART1_ALTERNATE
was added to allow UART1 as a DEBUG_LL target. Make the comment at the
top of this DTS reflect those changes.
Since we're touching this DTS add comments to show which blocks describe
UART0 and UART1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line] Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Wang Long [Wed, 24 Dec 2014 03:09:58 +0000 (03:09 +0000)]
ARM: dts: Add hip01-ca9x2 dts file
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch] Signed-off-by: Olof Johansson <olof@lixom.net>
Aleksei Mamlin [Tue, 20 Jan 2015 18:03:28 +0000 (22:03 +0400)]
ARM: dts: sun4i: Add Marsboard A10 board
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:45 +0000 (13:09 +0100)]
ARM: dts: sun5i: Add mk802_a10s board
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:44 +0000 (13:09 +0100)]
ARM: dts: sun4i: Add mk802ii board
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:09:43 +0000 (13:09 +0100)]
ARM: dts: sun4i: Add mk802 board
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 18 Jan 2015 12:08:19 +0000 (13:08 +0100)]
ARM: dts: sun7i: Add dts file for Bananapro board
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:29 +0000 (09:37 +0800)]
ARM: dts: sunxi: Use label to reference pio in sunxi-common-regulators
Use the label to reference the pin controller node, so that we can use
sunxi-common-regulators with sunxi families that don't share the same
address space mappings, such as sun9i.
This patch is mostly space changes due to the reduction of node parents.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 13 Jan 2015 01:37:27 +0000 (09:37 +0800)]
ARM: dts: sun9i: Add clock-indices property for bus gate clocks
of_clk_get_parent_name() uses the clock-indices property to resolve
clock phandle arguments in case that the argument index does not
match the clock-output-names sequence.
This is the case on sunxi, where we use the actual bit index as the
argument to the phandle. Add the clock-indices property so that
of_clk_get_parent_name() resolves the names correctly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun7i: cubieboard2: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Alexander Bersenev <bay@hackerdom.ru> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Roman Byshko <rbyshko@gmail.com>
The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
dtb file since some gpio-s surrounding the wlan/bluetooth are different,
it uses different camera sensors, and different DRAM timings.
Note that atm neither the wlan/bluetooth nor the camera are supported, so
atm their is no difference between the dts files, but because of the different
DRAM timings there are already separate u-boot configs for the 2 different
versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be
future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Jan 2015 10:47:04 +0000 (11:47 +0100)]
ARM: dts: sun8i: Enable lradc on a23-ippo-q8h-v5
The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Mon, 12 Jan 2015 04:34:02 +0000 (12:34 +0800)]
ARM: dts: sunxi: Add dtsi for AXP209 PMIC
The AXP209 PMIC is used with some Allwinner SoCs. This patch adds
a dtsi file listing all the regulator nodes. The regulators are
initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Zoltan HERPAI [Thu, 8 Jan 2015 09:34:24 +0000 (10:34 +0100)]
ARM: dts: pcduino: Enable user LED and button support for pcDuino
The pcDuino board has LEDs connected to PH15/PH16, and back/home/menu
buttons to PH17/18/19 respectively. Enable these via gpio-leds and
gpio-keys. This is shared across the v1 and v2 versions of the board.
Tested on a v2 and verified against the schematics of a v1.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added some newlines between the button nodes] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Mon, 19 Jan 2015 13:05:12 +0000 (14:05 +0100)]
ARM: dts: sunxi: Add simplefb nodes for de_be0-lcd0, de_be0-lcd0-tve0 pipelines
Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>