dma: cppi41: wait longer for the HW to return the descriptor
For a "complete" teardown we have to wait until the teardown descriptor
is returned by the hardware. The g_zero testcase "testusb -a -t 9" triggers
the following warning quite reliable:
and complains about a TD descriptor which is not returned. I've been
looking at several things and haven't noticed anything unusual that
might lead to this.
The manual says "to try again" until the descriptor comes out. I limited
the amount of retries to 100 retries in order to avoid an infinite number
of retries and so a busy-loop. Back then testing revealed that the
number of retries were around 20-30 so 100 seemed a good upper limit.
This g_zero test reaches without a problem 98 retries and it jumps
sometimes to 101 on am335x-evm and so the WARN_ON() triggers. Same test
run on beaglebone black and the retries start at 122 and my max value so
far was at 128.
So lets rise the limit to 500.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jingchang Lu [Wed, 22 Oct 2014 08:53:55 +0000 (16:53 +0800)]
dmaengine: fsl-edma: fixup reg offset and hw S/G support in big-endian model
The offset of all 8-/16-bit registers in big-endian eDMA model are
swapped in a 32-bit size opposite those in the little-endian model.
The hardware Scatter/Gather requires the subsequent TCDs stored in memory
in little endian independent of the register endian model, the eDMA engine
will do the swap if need.
This patch also use regular assignment for tcd variables r/w
instead of with io function previously that may not always be true.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Stefan Agner [Thu, 13 Nov 2014 11:56:02 +0000 (12:56 +0100)]
dmaengine: fsl-edma: fix calculation of remaining bytes
If the current transfer control descriptor (TCD) was not yet started,
the address will be the same as the initial address. Hence test if the
current address is less than or equal to the start address of each TCD.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sascha Hauer [Wed, 12 Nov 2014 22:04:29 +0000 (20:04 -0200)]
dma: imx-sdma: clarify about firmware not found error
When a firmware cannot be found for the SDMA engine then we can
continue with the internal ROM firmware.
The meaning of this message is frequently asked for, so make clear
that the driver still works with the internal ROM firmware and reduce
the loglevel from err to info.
same issue as commit 7f5ae3553685:
"Without DMA_PRIVATE the driver is not able to allocate more than one channel.
Since it uses dma_get_any_slave_channel that calls private_candidate, the
second allocation fails at
/* some channels are already publicly allocated */
"
According to the Atmel eXtended DMA controller datasheet, requesting a
DMA transfer flush for a channel is only revelant when this transfer is
source peripheral synchronized.
So we have to check this condition before requesting a channel flush by
writing the channel bit into the Global channel SoftWare Flush (GSWF)
register then waiting for flush to complete by monitoring the end of
Flush Interrupt Status (FIS) bit in the Channel Interrupt Status (CIS)
register.
Indeed, for non source peripheral synchronized transfer, writing the
channel bit into the GSWF register does nothing. Especially, the FIS bit
is never set into the CIS register. The former code looped forever
waiting for this bit to be set.
dmaengine: at_xdmac: prefer usage of readl/writel_relaxed
_relaxed version of readl and writel are not implemented on all
architecture so COMPILE_TEST has to be removed in order to not cause
some build failures.
Vinod Koul [Thu, 6 Nov 2014 12:32:52 +0000 (18:02 +0530)]
dmaengine: xdmac: fix print warning on dma_addr_t variable
As documented in printk-formats.txt the dma_addr_t should be printed with
%pad specfiers. This way it works on all archs.
make.cross ARCH=s390
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_slave_sg':
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:628:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: buf_addr=0x%08x, buf_len=%d, period_len=%d, dir=%s, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:690:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:716:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
>> drivers/dma/at_xdmac.c:731:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: src=0x%08x, dest=0x%08x, len=%d, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: remaining_size=%u\n", __func__, remaining_size);
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:852:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_tx_status':
>> drivers/dma/at_xdmac.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Thu, 6 Nov 2014 12:07:48 +0000 (17:37 +0530)]
dmaengine: xdmac: fix print warning on size_t variable
As documented in printk-formats.txt the size_t should be printed with
%zu/%zd specfiers. This way it works on all archs.
make.cross ARCH=avr32
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
>> drivers/dma/at_xdmac.c:794: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
>> drivers/dma/at_xdmac.c:815: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Thu, 6 Nov 2014 12:04:13 +0000 (17:34 +0530)]
dmaengine: at_xdmac: fix usage of read, write wrappers
This driver uses read_relaxed and writel_relaxed to read, write to IO
memory. the config defines COMPILE_TEST so gets compiled on different archs.
This causes issue as few archs like x86 etc don't define it.
So use readl/writel which is defined in all archs
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jingoo Han [Mon, 27 Oct 2014 12:36:26 +0000 (21:36 +0900)]
dmaengine: k3dma: Add CONFIG_PM_SLEEP to suspend/resume functions
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/dma/k3dma.c:790:12: warning: 'k3_dma_suspend' defined but not used [-Wunused-function]
drivers/dma/k3dma.c:806:12: warning: 'k3_dma_resume' defined but not used [-Wunused-function]
Jingoo Han [Mon, 27 Oct 2014 12:35:13 +0000 (21:35 +0900)]
dmaengine: sirf: Add CONFIG_PM_SLEEP to suspend/resume functions
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/dma/sirf-dma.c:838:12: warning: 'sirfsoc_dma_pm_suspend' defined but not used [-Wunused-function]
drivers/dma/sirf-dma.c:879:12: warning: 'sirfsoc_dma_pm_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: shdma: fix a race condition in __ld_cleanup()
This patch fixes a race condition about a list of shdma-base driver.
If we don't apply this patch, a dma slave driver (especially a usb
peripheral driver) may not be able to start the transfer.
If a dma slave driver has a callback, __ld_cleanup() will call
the callback before this driver removes the list. After the callback,
since the return value of __ld_cleanup() is not zero,
shdma_chan_ld_cleanup() calls __ld_cleanup() again. And, __ld_clean()
will removes the list.
At this time, if a dma slave driver calls dmaengine_submit() before
this driver removes the list, this driver will set schan->pm_state
to SHDMA_PM_PENDING in shdma_tx_submit(). And then, even if a dma
slave driver calls dma_async_issue_pending(), this driver don't
start the transfer because the schan->pm_state is SHDMA_PM_PENDING
in shdma_issue_pending().
So, this patch adds a new condition in __ld_clean() to check if the
schan->pm_state is SHDMA_PM_PENDING or not.
We currently have register offset information only for BAM IPs with revision
1.4.0. We add register offset table entries for the legacy (v1.3.0) version
of BAM IPs found on SoCs like APQ8064 and MSM8960.
The register offset table pointers are stored in DT data corresponding to the
BAM IP version specified in the compatible string.
Reviewed-by: Kumar Gala <galak@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The BAM DMA IP comes in different versions. The register offset layout varies
among these versions. The layouts depend on which generation/family of SoCs they
belong to.
The current SoCs(like 8084, 8074) have a layout where the Top level registers
come in the beginning of the address range, followed by pipe and event
registers. The BAM revision numbers fall above 1.4.0.
The older SoCs (like 8064, 8960) have a layout where the pipe registers come
first, and the top level come later. These have BAM revision numbers lesser than
1.4.0.
It isn't suitable to have macros provide the register offsets with the layouts
changed. Future BAM revisions may have different register layouts too. The
register addresses are now calculated by referring a table which contains a base
offset and multipliers for pipe/evnt/ee registers.
We have a common function bam_addr() which computes addresses for all the
registers. When computing address of top level/ee registers, we pass 0 to the
pipe argument in addr() since they don't have any multiple instances.
Some of the unused register definitions are removed. We can add new registers as
we need them.
Reviewed-by: Kumar Gala <galak@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Chen-Yu Tsai [Fri, 7 Nov 2014 04:15:47 +0000 (12:15 +0800)]
dmaengine: sun6i: Add support for Allwinner A23 (sun8i) variant
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Jingoo Han [Thu, 6 Nov 2014 01:10:09 +0000 (10:10 +0900)]
dma: imx-sdma: remove incorrect __init annotation from sdma_init()
When platform_driver_probe() is not used, sdma_probe() can be called
by bind/unbind via sysfs. In addition, sdma_init() can be called by
sdma_probe(). Thus, __init annotation should be removed from sdma_init(),
Also, this patch fixes section mismatch warning.
WARNING: drivers/dma/built-in.o(.text+0xd6e4): Section mismatch in reference from the function sdma_probe() to the function
.init.text:sdma_init()
The function sdma_probe() references
the function __init sdma_init().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_init is wrong.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andrew Jackson [Thu, 6 Nov 2014 11:39:47 +0000 (11:39 +0000)]
dmaengine: pl330: Correct device assignment.
Commit f6f2421c0a1c removed pl330_info structure by embedding it into
pl330_dmac structure, but did not ensure that the dmac->ddma.dev
pointer gets initialised before use. When dma_alloc_coherent() gets
called on arm64 a WARN() gets triggered due to dev being NULL.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/arm64/mm/dma-mapping.c:49 __dma_alloc_coherent+0xd0/0xe0()
Use an actual device structure for DMA allocation
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #5
Call trace:
[<ffffffc000087f24>] dump_backtrace+0x0/0x130
[<ffffffc000088064>] show_stack+0x10/0x1c
[<ffffffc0004e8af8>] dump_stack+0x74/0xb8
[<ffffffc0000aa444>] warn_slowpath_common+0x8c/0xb4
[<ffffffc0000aa4b8>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc000092580>] __dma_alloc_coherent+0xcc/0xe0
[<ffffffc000092734>] __dma_alloc_noncoherent+0x64/0x158
[<ffffffc000312cd8>] pl330_probe+0x650/0x8f0
[<ffffffc00030e1d4>] amba_probe+0xa0/0xc8
[<ffffffc000350240>] really_probe+0xc4/0x22c
[<ffffffc0003504b4>] __driver_attach+0xa0/0xa8
[<ffffffc00034e5fc>] bus_for_each_dev+0x54/0x98
[<ffffffc00034fd8c>] driver_attach+0x1c/0x28
[<ffffffc00034fa08>] bus_add_driver+0x14c/0x204
[<ffffffc000350b84>] driver_register+0x64/0x130
[<ffffffc00030dcf8>] amba_driver_register+0x50/0x5c
[<ffffffc0006a60d0>] pl330_driver_init+0x10/0x1c
[<ffffffc0000814ac>] do_one_initcall+0x88/0x19c
[<ffffffc00068dab8>] kernel_init_freeable+0x140/0x1e0
[<ffffffc0004e5e18>] kernel_init+0x10/0xd4
---[ end trace 76f2d47a444e523e ]---
(NULL device *): dmac_alloc_resources:1821 Can't allocate memory!
(NULL device *): Unable to create channels for DMAC
This patch will also ensure that any dev_err messages are printed
with the appropriate device name.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com> Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: xilinx: vdma: Check if the segment list is empty in a descriptor
The segment list in a descriptor should be checked for empty, else
it will try to access invalid address for the first call. This
patch fixes this issue.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Maxime Ripard [Tue, 28 Oct 2014 20:55:50 +0000 (21:55 +0100)]
Documentation: dmaengine: Add a documentation for the dma controller API
The dmaengine is neither trivial nor properly documented at the moment, which
means a lot of trial and error development, which is not that good for such a
central piece of the system.
Attempt at making such a documentation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[fixed some minor typos] Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Sun, 2 Nov 2014 22:45:52 +0000 (14:45 -0800)]
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Linus Torvalds [Sun, 2 Nov 2014 22:39:35 +0000 (14:39 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
Linus Torvalds [Sun, 2 Nov 2014 22:27:30 +0000 (14:27 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
Linus Torvalds [Sun, 2 Nov 2014 20:56:20 +0000 (12:56 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
Linus Torvalds [Sun, 2 Nov 2014 20:31:02 +0000 (12:31 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
Dave Airlie [Sun, 2 Nov 2014 19:23:17 +0000 (05:23 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Linus Torvalds [Sun, 2 Nov 2014 18:28:43 +0000 (10:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
Linus Torvalds [Sun, 2 Nov 2014 18:20:26 +0000 (10:20 -0800)]
irda: stop calling sk_prot->disconnect() on connection failure
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:56 +0000 (14:31 +0200)]
drm/exynos: correct connector->dpms field before resuming
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:55 +0000 (14:31 +0200)]
drm/exynos: enable vblank after DPMS on
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:54 +0000 (14:31 +0200)]
drm/exynos: init kms poll at the end of initialization
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Jan Kiszka [Wed, 8 Oct 2014 16:05:39 +0000 (18:05 +0200)]
KVM: nVMX: Disable preemption while reading from shadow VMCS
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Mon, 27 Oct 2014 22:03:43 +0000 (00:03 +0200)]
KVM: x86: Fix far-jump to non-canonical check
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Airlie [Sat, 1 Nov 2014 23:23:31 +0000 (09:23 +1000)]
Merge branch 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
Linus Torvalds [Sat, 1 Nov 2014 22:11:27 +0000 (15:11 -0700)]
Merge tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sat, 1 Nov 2014 22:08:04 +0000 (15:08 -0700)]
Merge tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
Linus Torvalds [Sat, 1 Nov 2014 17:41:26 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks
Linus Torvalds [Sat, 1 Nov 2014 02:51:11 +0000 (19:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Linus Torvalds [Sat, 1 Nov 2014 02:08:25 +0000 (19:08 -0700)]
Merge tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
An unintentional sysfs filename change in commit 5136b2da770d
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Andy Lutomirski [Sat, 1 Nov 2014 01:08:45 +0000 (18:08 -0700)]
x86_64, entry: Fix out of bounds read on sysenter
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes: 8c7aa698baca ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by: Rusty Russell <rusty@ozlabs.org> Cc: stable@vger.kernel.org Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2014 23:22:29 +0000 (16:22 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A set of miscellaneous ext4 bug fixes for 3.18"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
ext4: bail early when clearing inode journal flag fails
ext4: bail out from make_indexed_dir() on first error
jbd2: use a better hash function for the revoke table
ext4: prevent bugon on race between write/fcntl
ext4: remove extent status procfs files if journal load fails
ext4: disallow changing journal_csum option during remount
ext4: enable journal checksum when metadata checksum feature enabled
ext4: fix oops when loading block bitmap failed
ext4: fix overflow when updating superblock backups after resize
Linus Torvalds [Fri, 31 Oct 2014 23:18:47 +0000 (16:18 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota and ext3 fixes from Jan Kara.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs, jbd: use a more generic hash function
quota: Properly return errors from dquot_writeback_dquots()
ext3: Don't check quota format when there are no quota files
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
Pull sparc update from David Miller:
"Two changes:
1) It makes no sense to execute a VTOC partition table request in the
Sun virtual block device driver and fail to load if it doesn't
succeed because a) we don't use the result at all and b) it won't
succeed if there is an EFI partition on the disk, for example.
We read the partition table via the normal means in the block layer
anyways, so this is really completely useless, so just remove it.
From Dwight Engen.
2) Hook up new bpf system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: don't call VD_OP_GET_VTOC
sparc: Hook up bpf system call.
Linus Torvalds [Fri, 31 Oct 2014 21:43:42 +0000 (14:43 -0700)]
Merge tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze updates from Michal Simek:
- wire-up new bpf syscall
- fix PCI bug
- fix Kconfig warning
* tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire up bpf syscall
microblaze: Fix IO space breakage after of_pci_range_to_resource() change
microblaze: Fix missing NR_CPUS in menuconfig
Linus Torvalds [Fri, 31 Oct 2014 21:30:16 +0000 (14:30 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
Linus Torvalds [Fri, 31 Oct 2014 21:05:35 +0000 (14:05 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various scheduler fixes all over the place: three SCHED_DL fixes,
three sched/numa fixes, two generic race fixes and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/dl: Fix preemption checks
sched: Update comments for CLONE_NEWNS
sched: stop the unbound recursion in preempt_schedule_context()
sched/fair: Fix division by zero sysctl_numa_balancing_scan_size
sched/fair: Care divide error in update_task_scan_period()
sched/numa: Fix unsafe get_task_struct() in task_numa_assign()
sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer()
sched/deadline: Don't replenish from a !SCHED_DEADLINE entity
sched: Fix race between task_group and sched_task_group
Linus Torvalds [Fri, 31 Oct 2014 21:01:47 +0000 (14:01 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
Linus Torvalds [Fri, 31 Oct 2014 20:57:45 +0000 (13:57 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull futex fixes from Ingo Molnar:
"This contains two futex fixes: one fixes a race condition, the other
clarifies shared/private futex comments"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix a race condition between REQUEUE_PI and task death
futex: Mention key referencing differences between shared and private futexes
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:38:52 +0000 (13:38 -0400)]
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:28:54 +0000 (13:28 -0400)]
drivers: net: cpsw: Fix broken loop condition in switch mode
0d961b3b52f566f823070ce2366511a7f64b928c (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Fri, 31 Oct 2014 03:50:15 +0000 (20:50 -0700)]
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Fri, 31 Oct 2014 16:28:03 +0000 (18:28 +0200)]
stmmac: pci: set default of the filter bins
The commit 3b57de958e2a brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e2a (net: stmmac: Support devicetree configs for mcast and ucast filter entries) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Thu, 30 Oct 2014 16:59:27 +0000 (09:59 -0700)]
net: smc91x: Fix gpios for device tree based booting
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dwight Engen [Thu, 30 Oct 2014 19:55:35 +0000 (15:55 -0400)]
sunvdc: don't call VD_OP_GET_VTOC
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>