Since there is no protection around SYNC host command mechanism, at least WARN
when collision happens between two SYNC host comamnds. I am not sure there is a
real issue (beyond the HCMD_ACTIVE flag maintenance) with having two SYNC host
commands at the same time, but at least now, we will know about it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Bus specific layer must know how to return the struct device* of the device.
Implement that as a callback of iwl_bus_ops and use that callback instead of
using the priv->pdev pointer which is meant to disappear soon.
Since the struct device * is needed in hot path, iwl_bus holds a pointer to it
instead of calling get_dev all the time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be
done on this bus.
For the moment only set_prv_data is implemented. More to come...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn: add a iwl_pci.[ch] files that will contain all PCI specific code
Move some PCI functionality to the new iwl_pci.[ch] files:
* the PCI_DEVICE_TABLE
* the pci_driver struct definition
* the PCI probe / remove functions
* the PCI suspend / resume functions
All these functions are now split: the trigger comes from the PCI layer which
calls to the bus generic code located in the other files.
This is the beginning only. There are still a lot of PCI related code needs
to be gathered.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn: don't disable interrupts after the NIC has been reset
It is superfluous to disable the interrupts after we reset the NIC. The only
entity that could enable the interrupts after the NIC is reset is the driver.
So remove this pointless action.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Rafał Miłecki [Wed, 15 Jun 2011 23:59:20 +0000 (01:59 +0200)]
b43: HT-PHY: implement switching analog
Turning it on is always done between reading PHY version and radio
version, so it was easy to find it in MMIO dumps from ndiswrapper.
Turning off is done by writing different values to the same registers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 15 Jun 2011 23:59:19 +0000 (01:59 +0200)]
b43: HT-PHY: implement radio ops
Every PHY has some specific bit used for reading radio regs. Analyze of
MMIO dumps from BCM4331 and ndiswrapper has shown it is 0x200 for HT.
radio_read(0x037f) -> 0x0073
radio_write(0x017f) <- 0x0072
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Wed, 15 Jun 2011 22:03:22 +0000 (18:03 -0400)]
ath5k: minor cleanup
Move an extern variable declaration to a header file. Prefix all
functions with "ath5k_". Make ath5k_intr() static. Remove unneeded
forward declarations. Remove pointless "extern" in a function
declaration.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/resume ath9k_stop will always call ath_radio_disable
which will inturn call ath9k_hw_configpcipowersave, so no need to call
it explicitly in ath9k_stop
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 15 Jun 2011 13:10:10 +0000 (16:10 +0300)]
iwlegacy: fix up brokenness caused by cleanup
Patch 7f1f9742514 "iwlegacy: refactor iwl4965_mac_channel_switch"
reversed a test and also it changed a spin_lock_irq() to
spin_lock(). I assume the spin_lock change was a mistake because
the unlock was left as spin_unlock_irq().
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few debug messages for some of the possible scenarios
where we can detect PAPRD failures. this will help us to be
sure that we had really enabled PAPRD
Cc: susinder@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_init_card’:
drivers/net/wireless/libertas/if_spi.c:1035: warning: unused variable ‘spi’
The variable is used only in a macro which uses the args only for DEBUG builds.
Remove the 'spi' variable completely.
Signed-off-by: Nikanth Karthikesan <nikanth@google.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Mon, 13 Jun 2011 09:47:30 +0000 (12:47 +0300)]
mac80211: add cancel_hw_scan() callback
When suspending, __ieee80211_suspend() calls ieee80211_scan_cancel(),
which will only cancel sw scan. In order to cancel hw scan, the
low-level driver has to cancel it in the suspend() callback. however,
this is too late, as a new scan_work will be enqueued (while the driver
is going into suspend).
Add a new cancel_hw_scan() callback, asking the driver to cancel an
active hw scan, and call it in ieee80211_scan_cancel().
Signed-off-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
warning message
drivers/ssb/driver_chipcommon_pmu.c: In function ssb_pmu_resources_init
drivers/ssb/driver_chipcommon_pmu.c:420:15: warning: updown_tab_size may
be used uninitilized in this function.
updown_tab_size and depend_tab_size may not be set in the bus->chip_id
switch statement, so set to 0 by default to avoid using uninitialized
stack space.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com> Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Stewart [Fri, 10 Jun 2011 15:00:19 +0000 (07:00 -0800)]
mac80211: Start monitor work on restart
Trigger connection monitor on resume from suspend. Since we
have been sleeping, there is reason to suspect that we might
not still be associated. The speed of detecting loss of
{connection,authentication} is worth the cost of the small
additional traffic at resume.
Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 6 Jun 2011 16:41:15 +0000 (09:41 -0700)]
iwlagn: don't check ucode subtype
The ucode subtypes keep changing, and there's no
particular reason to be checking them (other than
a paranoid sanity check). Since the numbers are
also in conflict between different ucode images
now, simply don't check them any more and rely on
the images being built correctly.
Also, to indicate that, rename the constants and
the enum, moving it to a different file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Larry Finger [Fri, 10 Jun 2011 16:05:23 +0000 (11:05 -0500)]
rtlwifi: Fix warnings on parisc arch
In "Build regressions/improvements in v3.0-rc2", Geert Uytterhoeven
reports a number of warnings that occur for parisc builds of rtlwifi
and dependents.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers: bcma: export bcma_core_disable() function
In the brcm80211 driver we disable the 80211 core when the driver is
'down'. The bcma_core_disable() function exactly does the same as
our implementation so exporting this function makes sense.
Cc: linux-wireless@vger.kernel.org Cc: Rafal Milecki <zajec5@gmail.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Avoid global adapter pointer usage
a) in sdio.c by moving some code from mwifiex_cleanup_module() to
mwifiex_sdio_remove().
b) in main.c by passing an extra parameter to few functions.
2) Add new variable "user_rmmod" to identify if mwifiex_sdio_remove()
callback function is called in card removal or rmmod context. These
code changes are adapted from Libertas driver.
3) Remove unnecessary NULL pointer check for "func" pointer in
mwifiex_sdio_remove().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recover from statistics code was added during 6xxx devices development,
I don't think is needed on old devices. Also it is suspicious to cause
random, unreproducible microcode errors and hangs. So remove it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Tue, 7 Jun 2011 17:15:57 +0000 (18:15 +0100)]
libertas: add sd8686 reset_card support
At http://dev.laptop.org/ticket/10748 we are seeing a case of the
libertas firmware randomly stopping responding to commands after
resume. Careful monitoring of communications indicates a firmware or
hardware bug, which has been reported to Marvell.
Work around this issue by adding a reset_card method; this is
automatically called when command timeouts are detected and provides an
instant recovery to this situation.
Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vincent Zweije [Tue, 7 Jun 2011 14:37:09 +0000 (16:37 +0200)]
networking: fix warning about unused label wake_up
Function ieee80211_reconfig in net/mac80211/util.c contains label wake_up
which is defined unconditionally, but only used with CONFIG_PM. Gcc
warns about this when CONFIG_PM is not defined.
This patch makes the label's definition dependent on CONFIG_PM too,
eliminating the warning.
Paul Stewart [Wed, 8 Jun 2011 12:52:52 +0000 (05:52 -0700)]
cfg80211: Ignore downstream DEAUTH for authtry_bsses
Downsteram DEAUTH messages do not refer to a current authentication
attempt -- AUTH responses do. Therefore we should not allow DEAUTH
from an AP to void state for an AUTH attempt in progress.
Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mike McCormack [Mon, 6 Jun 2011 14:12:42 +0000 (23:12 +0900)]
rtlwifi: Resubmit skbs with bad CRC early
Once we realize a bad packet was received, don't
waste time unmapping it, freeing it, then allocation
a new skb and mapping it, just resubmit the existing
skb.
Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Mon, 6 Jun 2011 09:59:29 +0000 (12:59 +0300)]
mac80211: add ieee80211_get_operstate() function
Add ieee80211_get_operstate() function to get the operstate
of the netdevice.
This is needed for drivers that need to know when the interface
is IF_OPER_UP (e.g. wl12xx), and block notifiers can't be used
(e.g. because the interface is already IF_OPER_UP, like after
resuming from suspend)
Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
shutdown should wait for SCO link to be properly disconnected before
detroying the socket, otherwise an application using the socket may
assume link is properly disconnected before it really happens which
can be a problem when e.g synchronizing profile switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In function 'copy_from_user',
inlined from 'rfcomm_sock_setsockopt' at
net/bluetooth/rfcomm/sock.c:705:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 3 Jun 2011 23:21:07 +0000 (16:21 -0700)]
Bluetooth: Restore accidentally-deleted line
When code was moved from l2cap_core.c to l2cap_sock.c in commit 6de0702b5b93da0ef097aa092b4597fbc024ebba, one line was dropped
from the old __l2cap_sock_close() implementation. This sk_state
change should still be in l2cap_chan_close().
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the link key is secure (authenticated or combination 16 digit)
the sec_level will be always BT_SECURITY_HIGH. Therefore, instead
of checking the link key type simply check the sec_level on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Jaikumar Ganesh [Tue, 24 May 2011 01:06:04 +0000 (18:06 -0700)]
Bluetooth: Add BT_POWER L2CAP socket option.
Add BT_POWER socket option used to control the power
characteristics of the underlying ACL link. When the remote end
has put the link in sniff mode and the host stack wants to send
data we need need to explicitly exit sniff mode to work well with
certain devices (For example, A2DP on Plantronics Voyager 855).
However, this causes problems with HID devices.
Hence, moving into active mode when sending data, irrespective
of who set the sniff mode has been made as a socket option. By
default, we will move into active mode. HID devices can set the
L2CAP socket option to prevent this from happening.
Currently, this has been implemented for L2CAP sockets. This has been
tested with incoming and outgoing L2CAP sockets for HID and A2DP.
Based on discussions on linux-bluetooth and patches submitted by
Andrei Emeltchenko.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Tue, 31 May 2011 17:20:57 +0000 (14:20 -0300)]
Bluetooth: Set 'peer_addr_type' in hci_le_connect()
Set the 'peer_addr_type' field of the LE Create Connection command
sent in hci_le_connect().
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Tue, 31 May 2011 17:20:56 +0000 (14:20 -0300)]
Bluetooth: Check advertising cache in hci_connect()
When connecting to a LE device, we need to check the advertising
cache in order to know the address type of that device.
If its advertising entry is not found, the connection is not
established and hci_connect() returns error.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Tue, 31 May 2011 17:20:55 +0000 (14:20 -0300)]
Bluetooth: Remove useless check in hci_connect()
There is no need to check the connection's state since hci_conn_add()
has just created a new connection and its state has been set properly.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Tue, 31 May 2011 17:20:54 +0000 (14:20 -0300)]
Bluetooth: Add 'dst_type' field to struct hci_conn
This patch adds a new field (dst_type) to the struct hci_conn which
holds the type of the destination address (bdaddr_t dst). This
approach is needed in order to use the struct hci_conn as an
abstraction of LE connections in HCI Layer. For non-LE this field
is ignored.
This patch also set properly the 'dst_type' field after initializing
LE hci_conn structures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Legacy devices don't re-authenticate the link properly if a link key
already exists. Thus, don't update sec_level for this case even if
hci_auth_complete_evt indicates success. Otherwise the sec_level will
not reflect a real security on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Thu, 26 May 2011 19:23:53 +0000 (16:23 -0300)]
Bluetooth: Advertising entries lifetime
This patch adds a timer to clear 'adv_entries' after three minutes.
After some amount of time, the advertising entries cached during
the last LE scan should be considered expired and they should be
removed from the advertising cache.
It was chosen a three minutes timeout as an initial attempt. This
value might change in future.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Thu, 26 May 2011 19:23:51 +0000 (16:23 -0300)]
Bluetooth: Add Advertising Report Meta Event handler
This patch adds a function to handle LE Advertising Report Meta
Events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Thu, 26 May 2011 19:23:50 +0000 (16:23 -0300)]
Bluetooth: LE advertising cache
This patch implements the LE advertising cache. It stores sensitive
information (bdaddr and bdaddr_type so far) gathered from LE
advertising report events.
Only advertising entries from connectables devices are added to the
cache.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Remove export of l2cap_chan_clear_timer()
The call to l2cap_chan_clear_timer() is not really needed in l2cap_sock.c.
This patch also adds a call to l2cap_chan_clear_timer() to the only place
in __l2cap_sock_close() that wasn't calling it. It's safe call it there
because l2cap_chan_clear_timer() check first for timer_peding().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
projects / linux-beck.git / log