Michael Krufky [Sun, 16 Dec 2007 22:53:32 +0000 (19:53 -0300)]
V4L/DVB (6840): tuner: convert tda9887 to use TUNER_SET_CONFIG
Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.
Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops
analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frej Drejhammar [Mon, 5 Nov 2007 20:57:11 +0000 (17:57 -0300)]
V4L/DVB (6834): cx88-video: Enable selection of the WM8775 for cx88 cards
The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
V4L/DVB (6833): Don't limit cx88 audio routing to blackbird boards
All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
V4L/DVB (6831): Audio routes fix for blackbird boards with the wm8775 ADC
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used
drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 01:23:30 +0000 (22:23 -0300)]
V4L/DVB (6801): tda18271: pass i2c gate configuration into tda18271_attach()
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.
If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.
If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (6795): Add EXPORT_SYMBOL_GPL to the saa7134 video control routines
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Michael Krufky [Sun, 9 Dec 2007 05:26:48 +0000 (02:26 -0300)]
V4L/DVB (6785): tda8290: remove dependency on struct tuner
- remove dependency of tda8290 module on struct tuner
- move tuner_foo printk macros from tuner-driver.h into tuner-core.c
- clean up #includes of tuner-i2c.h / tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver tries to keep all device specific attributes in a
single data structure in one source file. This change further cleans
up how that table is set up. We now try to group everything together
for each specific device, and the number of symbols exported from this
module has now been reduced to a single global.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (6755): Avoid troubles when using multiple devices
mv_count is a counter used to move the vertical bars. Before this patch, it
where a static var. This works fine for just one device. However, when using
multiple devices, every device would increment it.
This patch moves it to its correct place: struct vivi_dev. So, now, each device
has its own data.
V4L/DVB (6753): Fix vivi to support non-zero minor node
There were a trouble at vivi driver when using non-zero inodes. This where due
to not properly preserving the minor inode after calling video_register. Since
this driver is a reference for newer drivers, and it is possible to have more
than one video device inside the machine, this patch makes vivi to dynamically
allocate video_device struct.
Thanks to Gregor Jasny <jasny@vidsoft.de> for pointing the issue.
Also, this patch removes a very anoying (but useless) message of not having a
proper release call.
CC: Gregor Jasny <jasny@vidsoft.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Albert Graham [Sun, 9 Dec 2007 12:44:38 +0000 (09:44 -0300)]
V4L/DVB (6752): saa7134: Enable remote control support for Avermedia M102
This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: Albert Graham <agraham@g-b.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 reads a little-endian 32-bit value whereas cx25840_write4 writes
the 32-bit value as big-endian. Convert write4 to use little-endian as well
(that's the correct endianness).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (6735): Reorder functions to make easier to compare with the previous code
After this patch, the order of the functions will be the same as before the
patch converting the driver to user video_ioctl2. This makes easier to diff
between the previous version and the newer one.
ivtv-yuv code clean up & reformat. Includes minor changes to some debug lines.
Also fixes a bug found during the reformatting, which would cause the
incorrect amount of yuv data to be sent to the card if source cropping
coordinates were used.
Apart from the bug-fix, there should be no functional difference to the
previous version.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 5 Nov 2007 17:30:03 +0000 (14:30 -0300)]
V4L/DVB (6718): ivtv: ivtv yuv format description correction
The driver was incorrectly reporting that it supported YUV 4:2:2 output, when
it is actually YUV 4:2:0. Though I believe the hardware can be pushed to
4:2:2, we don't currently support that.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 5 Nov 2007 17:27:09 +0000 (14:27 -0300)]
V4L/DVB (6717): ivtv: Initial merge of video48 yuv handling into the IVTV_IOC_DMA_FRAME framework
Previously, all yuv data written to /dev/video48 had only basic support with
no double buffering to avoid display tearing.
With this patch, yuv frames written to video48 are now handled by the existing
IVTV_IOC_DMA_FRAME framework. As such, the frames are hardware buffered to
avoid tearing, and honour scaling mode & field order options. Unlike the
proprietary IVTV_IOC_DMA_FRAME ioctl, all parameters are controlled by the
V4L2 API.
Due to mpeg & yuv output restrictions being different, their V4L2 output
controls have been separated. To control the yuv output, the V4L2 calls must
be done via video48.
If the ivtvfb module is loaded, there will be one side effect to this merge.
The yuv output window will be constrained to the visible framebuffer area. In
the event that a virtual framebuffer size is being used, the limit to the
output size will be the virtual dimensions, but only the portion that falls
within the currently visible area of the framebuffer will be shown.
Like the IVTV_IOC_DMA_FRAME ioctl, the supplied frames must be padded to 720
pixels wide. However the height must only be padded up the nearest multiple
of 32. This would mean an image of 102 lines must be padded to 128. As long
as the true source image size is given, the padding will not be visible in
the final output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 22 Oct 2007 17:24:26 +0000 (14:24 -0300)]
V4L/DVB (6716): ivtv: yuv interlace mode change
Interlace mode selection code moved into the frame setup phase, so it's now
run before the frame is loaded into a hardware buffer. Given that it can
affect how a new frame is displayed, it was a bit stupid running it after the
frame was already visible.
A few stray interlace related variables which were linked to individual frames
have now been moved into the yuv_frame_info struct. This means that all
variables linked to a specific frame are in the same place & not scattered.
Minor code reformatting in areas touched by the above changes.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To reduce the number of display register accesses, the yuv code keeps track of
the current video settings. Should there be a change in any single parameter,
it will update the associated display registers to ensure everything is
displayed correctly.
The existing check also looks at the field order for the video. This is not
required, since field reversal does not require any display register changes.
This patch removes the field order from the check.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sun, 21 Oct 2007 11:09:10 +0000 (08:09 -0300)]
V4L/DVB (6714): ivtv: yuv frame parameter fix
Inadvertently missed a line when converting code to new hardware buffering
method. In some circumstances, this would lead to a frame being displayed
using parameters belonging to another frame.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the yuv output stream buffer is divided into blocks whose size
depend on the broadcast standard selected during the driver init phase.
However, the standard can be changed after the init phase. This effectively
breaks the yuv output stream handler, since it relies on the different yuv
planes being block aligned.
This patch changes the setup, so that the block size is always the same. The
decoder dma function has been modified to cope with the fact that the second
yuv plane may no longer be block aligned. The start of the yuv frame must
still be at the beginning of a block, so the stream write function has also
been modified to ensure this is always true.
Also, the stream write function will now initiate a yuv dma transfer as soon
as a full frame is ready. It will not wait until the current write request
has completed, or the stream buffer becomes full.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Mon, 3 Dec 2007 04:47:12 +0000 (01:47 -0300)]
V4L/DVB (6709): pvrusb2: minor rework for default video standard handling
pvrusb2: When a per-device-type default video standard is declared,
handle it in such a way that it can be correctly and unambiguously
reported in the system log.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Mon, 3 Dec 2007 04:44:43 +0000 (01:44 -0300)]
V4L/DVB (6707): pvrusb2: Remove use of volatile in pipeline control state machine
pvrusb2: Eliminate use of volatile in pipeline control state
variables. These were all cases of paranoia; upon further review the
overall mechanism employed here should not require use of volatile.
This had originally been done out of paranoia, and I have since been
convinced that the paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Mon, 3 Dec 2007 04:43:23 +0000 (01:43 -0300)]
V4L/DVB (6706): pvrusb2: Remove use of volatile in command sequencer
pvrusb2: Remove use of volatile for command sequencer; these variables
are set by interrupt-context code and we check their state in such a
manner that there should be no race conditions. This had originally
been done out of paranoia, and I have since been convinced that the
paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / karo-tx-linux.git / log