Ville Syrjälä [Mon, 11 Apr 2016 13:56:31 +0000 (16:56 +0300)]
drm/i915: Move DPINVGTT setup to vlv_display_irq_reset()
DPINVGTT lives inside the disp2d power well so we can't frob it unless
we know the power well is active. Let's this stuff into
vlv_display_irq_reset() which is only called at the right times so that
we don't get unclaimed register access errors.
Ville Syrjälä [Mon, 11 Apr 2016 13:56:30 +0000 (16:56 +0300)]
drm/i915: Move vlv_init_display_clock_gating() to the display power well
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Ville Syrjälä [Mon, 11 Apr 2016 13:56:28 +0000 (16:56 +0300)]
drm/i915: Use GEN5_IRQ_INIT() in vlv_display_irq_postinstall()
Replace the hand rolled IMR/IER setup in vlv_display_irq_postinstall()
with GEN5_IRQ_INIT(). Also rename the iir_mask to enable_mask to avoid
consusion since we no longer deal with IIR here.
Ville Syrjälä [Mon, 11 Apr 2016 13:56:27 +0000 (16:56 +0300)]
drm/i915: Clear display interrupt before enabling when turning on the power well
For a bit of extra paranoia make sure the display irqs are all cleared
before we enabled them when turning on the power well. This should
really be the case already since the power well was off which resets
everything.
Ville Syrjälä [Mon, 11 Apr 2016 13:56:25 +0000 (16:56 +0300)]
drm/i915: Skip display irq setup if display irqs aren't flagged as enabled
During runtime PM we'll be reinitializing interrupt support from the
ground up. However since the display power well will be off at that
time, well end up with a ton of unclaimed register accesses from the
display irq setup. Since we turned off the power well already before
runtime suspend, we've flagged display irqs as disabled during runtime
PM transitions. So we can just check that flag to see if we should do
skip display irqs during irq setup.
During driver load display irqs will be flagged as enabled since we've
turned on the power well already, however the power well code will have
skipped the display irq setup since irq support as a whole wasn't yet
enabled when the power well was enabled. So we'll want to do the display
irq setup in that case.
Ville Syrjälä [Tue, 12 Apr 2016 15:56:14 +0000 (18:56 +0300)]
drm/i915: Fix up vlv/chv display irq setup
The vlv/chv display irq setup was a bit of mess after I ran out of steam
when working on it last. Fix it up so that we just have a _reset() and
_postinstall() hooks for the display irqs, and use those consistently.
v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in
vlv_display_irq_reset() (Imre)
Ville Syrjälä [Mon, 11 Apr 2016 13:56:23 +0000 (16:56 +0300)]
drm/i915: Remove "VLV magic" from irq setup
No clue what this is supposed to achieve. I think it's been there since
the very beginning, so presumably some kind of kludge for very early
silicon. Let's just throw it out.
Ville Syrjälä [Fri, 1 Apr 2016 18:53:19 +0000 (21:53 +0300)]
drm/i915: Replace ILK eDP underrun suppression with something better
The underruns we were seeing when enabling eDP port A on ILK seem to
have been caused by prematurely clearing the LP1+ watermark values when
disabling LP1+ watermarks. Now that the watermarks are handled
properly, we can rip out the underrun suppression around the port A
enable.
We still need to worry about the underruns on FDI when enabling
the eDP PLL. But as Bspec tells us, we can avoid that by a vblank
wait on the pipe driving FDI just prior to enabling the eDP PLL.
Ville Syrjälä [Fri, 1 Apr 2016 18:53:18 +0000 (21:53 +0300)]
drm/i915: Make sure LP1+ watermarks levels are preserved when going from 1 to 2 pipes
Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.
Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.
Ville Syrjälä [Fri, 1 Apr 2016 18:53:17 +0000 (21:53 +0300)]
drm/i915: Try to shut up more ILK underruns
Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.
My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?
I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.
A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.
drm/i915: Only grab correct forcewake for the engine with execlists
Rather than blindly waking up all forcewake domains on command
submission, we can teach each engine what is (or are) the correct
one to take.
On platforms with multiple forcewake domains like VLV, CHV, SKL
and BXT, this has the potential of lowering the GPU and CPU
power use and submission latency.
To implement it we add a function named
intel_uncore_forcewake_for_reg whose purpose is to query which
forcewake domains need to be taken to read or write a specific
register with raw mmio accessors.
These enables the execlists engine setup to query which
forcewake domains are relevant per engine on the currently
running platform.
v2:
* Kerneldoc.
* Split from intel_uncore.c macro extraction, WARN_ON,
no warns on old platforms. (Chris Wilson)
v3:
* Single domain per engine, mention all registers,
bi-directional function and a new name, fix handling
of gen6 and gen7 writes. (Chris Wilson)
drm/i915: Extract knowledge of register forcewake domains
Knowledge of which register per platform belonds in which
forcewake domain was embedded in the MMIO accessors themselves.
Extract it into standalone macros so they can be used from
new code in the following patches.
This causes GCC to compile some of the MMIO accessors slightly
differently and grows the code a tiny amount. But none of the
growth is on the fast-path so it does not matter hugely.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: Do not serialize forcewake acquire across domains
On platforms with multiple forcewake domains it seems more efficient
to request all desired ones and then to wait for acks to avoid
needlessly serializing on each domain.
As the vast majority of users do not use the domain id variable,
we can eliminate it from the iterator and also change the latter
using the same principle as was recently done for for_each_engine.
For a couple of callers which do need the domain mask, store it
in the domain array (which already has the domain id), then both
can be retrieved thence.
Result is clearer code and smaller generated binary, especially
in the tight fw get/put loops. Also, relationship between domain
id and mask is no longer assumed in the macro.
v2: Improve grammar in the commit message and rename the
iterator to for_each_fw_domain_masked for consistency.
(Dave Gordon)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
drm/i915: Use consistent forcewake auto-release timeout across kernel configs
Because it is based on jiffies, current implementation releases the
forcewake at any time between straight away and between 1ms and 10ms,
depending on the kernel configuration (CONFIG_HZ).
This is probably not what has been desired, since the dynamics of keeping
parts of the GPU awake should not be correlated with this kernel
configuration parameter.
Change the auto-release mechanism to use hrtimers and set the timeout to
1ms with a 1ms of slack. This should make the GPU power consistent
across kernel configs, and timer slack should enable some timer coalescing
where multiple force-wake domains exist, or with unrelated timers.
For GlBench/T-Rex this decreases the number of forcewake releases from
~480 to ~300 per second, and for a heavy combined OGL/OCL test from
~670 to ~360 (HZ=1000 kernel).
Even though this reduction can be attributed to the average release period
extending from 0-1ms to 1-2ms, as discussed above, it will make the
forcewake timeout consistent for different CONFIG_HZ values.
Real life measurements with the above workload has shown that, with this
patch, both manage to auto-release the forcewake between 2-4 times per
10ms, even though the number of forcewake gets is dramatically different.
T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each
10ms period, while the OGL/OCL test requests 250 and 380 times in the same
period.
The two data points together suggest that the nature of the forwake
accesses is bursty and that further changes and potential timeout
extensions, or moving the start of timeout from the first to the last
automatic forcewake grab, should be carefully measured for power and
performance effects.
v2:
* Commit spelling. (Dave Gordon)
* More discussion on numbers in the commit. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Dave Gordon <david.s.gordon@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Mon, 11 Apr 2016 07:23:51 +0000 (10:23 +0300)]
drm/i915: Get panel_type from OpRegion panel details
We've had problems on several occasions with using the panel type
from the VBT block 40. Usually it seems to be 2, which often
doesn't give us the correct timings for the panel. After some
more digging I found a way to get a panel type via the OpRegion
SWSCI GBDA "Get Panel Details" method. Let's try to use it.
The spec has this to say about the output:
"Bits [15:8] - Panel Type
Bits contain the panel type user setting from CMOS
00h = Not Valid, use default Panel Type & Timings from VBT
01h - 0Fh = Panel Number"
Another version of the spec lists the valid range as 1-16, which makes
more sense since VBT supports 16 panels. Based on actual results
from Rob's G45, 1-16 is what we need to accept.
The other bits in the output don't look relevant for the problem at
hand.
The input is specified as:
"Bits [31:4] - Reserved
Reserved (must be zero)
Bits [3:0] - Panel Number
These bits contain the sequential index of Panel, starting at 0 and
counting upwards from the first integrated Internal Flat-Panel Display
Encoder present, and then from the first external Display Encoder
(e.g., S/DVO-B then S/DVO-C) which supports Internal Flat-Panels.
0h - 0Fh = Panel number"
For now I've just hardcoded the input panel number as 0. That would seem
like a decent choise for LVDS. Not so sure about eDP when port != A.
v2: Accept values 1-16
Filter out bogus results in opregion code (Jani)
Add debug logging for all the different branches (Jani)
Ville Syrjälä [Mon, 11 Apr 2016 07:22:09 +0000 (10:22 +0300)]
drm/i915: Reject panel_type > 0xf from VBT
VBT can only contain 16 panel entries, indexed with the panel_type.
To play it safe we should reject panel_type > 0xf, so that we don't
read past the valid data.
Ville Syrjälä [Mon, 7 Mar 2016 15:56:59 +0000 (17:56 +0200)]
drm/i915: Restore GMBUS operation after a failed bit-banging fallback
When the GMBUS based i2c transfer times out, we try to fall back to
bit-banging and retry the operation that way. However if the bit-banging
attempt also fails, we should probably go back to the GMBUS method for
the next attempt. Maybe there simply wasn't anyone one the bus at this
time.
There's also a bit of a mess going on with the force_bit handling.
It's supposed to be a ref count actually, and it is as far as
intel_gmbus_force_bit() is concerned. But it's treated as just a
flag by the timeout based bit-banging fallback. I suppose that's
fine since we should never end up in the timeout fallback case
if force_bit was already non-zero. However now that we want to restore
things back to where they were after the bit-banging attempt failed,
we're going to have to do things a bit differently to avoid clobbering
the force_bit count as set up by intel_gmbus_force_bit(). So let's
dedicate the high bit as a flag for the low level timeout based fallback
and treat the rest of the bits as a ref count just as before.
Ville Syrjälä [Mon, 7 Mar 2016 15:56:58 +0000 (17:56 +0200)]
drm/i915: Protect force_bit with gmbus_mutex
Extend the protection of gmbus_mutex around the force_bit
RMW in intel_gmbus_force_bit(), in case someone gets the
idea of calling it from a separate thread while there's
other stuff happening on the same bus.
Chris Wilson [Tue, 5 Apr 2016 14:00:00 +0000 (15:00 +0100)]
drm/i915/userptr: Hold mmref whilst calling get-user-pages
Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.
Chris Wilson [Tue, 5 Apr 2016 13:59:59 +0000 (14:59 +0100)]
drm/i915/userptr: Flush cancellations before mmu-notifier invalidate returns
In order to ensure that all invalidations are completed before the
operation returns to userspace (i.e. before the munmap() syscall returns)
we need to wait upon the outstanding operations.
We are allowed to block inside the invalidate_range_start callback, and
as struct_mutex is the inner lock with mmap_sem we can wait upon the
struct_mutex without provoking lockdep into warning about a deadlock.
However, we don't actually want to wait upon outstanding rendering
whilst holding the struct_mutex if we can help it otherwise we also
block other processes from submitting work to the GPU. So first we do a
wait without the lock and then when we reacquire the lock, we double
check that everything is ready for removing the invalidated pages.
Finally to wait upon the outstanding unpinning tasks, we create a
private workqueue as a means to conveniently wait upon all at once. The
drawback is that this workqueue is per-mm, so any threads concurrently
invalidating objects will wait upon each other. The advantage of using
the workqueue is that we can wait in parallel for completion of
rendering and unpinning of several objects (of particular importance if
the process terminates with a whole mm full of objects).
v2: Apply a cup of tea to the changelog.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94699
Testcase: igt/gem_userptr_blits/sync-unmap-cycles Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Daniel Vetter [Mon, 11 Apr 2016 17:21:06 +0000 (19:21 +0200)]
Merge tag 'v4.6-rc3' into drm-intel-next-queued
Linux 4.6-rc3
Backmerge requested by Chris Wilson to make his patches apply cleanly.
Tiny conflict in vmalloc.c with the (properly acked and all) patch in
drm-intel-next:
Chris Wilson [Fri, 8 Apr 2016 11:11:14 +0000 (12:11 +0100)]
drm/i915: Avoid allocating a vmap arena for a single page
If we want a contiguous mapping of a single page sized object, we can
forgo using vmap() and just use a regular kmap(). Note that this is only
suitable if the desired pgprot_t is compatible.
Chris Wilson [Fri, 8 Apr 2016 11:11:13 +0000 (12:11 +0100)]
drm,i915: Introduce drm_malloc_gfp()
I have instances where I want to use drm_malloc_ab() but with a custom
gfp mask. And with those, where I want a temporary allocation, I want to
try a high-order kmalloc() before using a vmalloc().
We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.
v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper
v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Chris Wilson [Fri, 8 Apr 2016 11:11:10 +0000 (12:11 +0100)]
drm/i915: Consolidate common error handling in intel_pin_and_map_ringbuffer_obj
After we pin the ringbuffer into the GGTT, all error paths need to unpin
it again. Move this common step into one block, and make the unable to
iomap error code consistent (i.e. treat it as out of memory to avoid
confusing it with a invalid argument).
Dongwon Kim [Thu, 17 Mar 2016 01:06:13 +0000 (18:06 -0700)]
drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit
For BXT, description of polarities of PORT_PLL_REF_SEL
has been reversed for newer Gen9LP steppings according to the
recent update in Bspec. This bit now should be set for
"Non-SSC" mode for all Gen9LP starting from B0 stepping.
v2: Only B0 and newer stepping should be affected by this
change.
drm/i915: Rename hw state checker to hw state verifier.
Check functions are used by atomic to see if the new state will
be allowed. There's also a hw state checker which checks afterwards
that the committed state is correct. Rename it to hw state verifier
to reduce some confusion.
The modeset state verifier no longer has full access to the hardware,
instead it should only verify affected crtc's.
Looking for disabled stuff can be verified immediately after all crtc
disables have completed, while each enabled crtc can be verified right
after being enabled.
drm/i915: Make modeset state verifier take crtc as argument.
This will make it easier to keep the crtc checker when atomic
commit is reworked for asynchronous commits. This prevents checking
crtc's that were not part of the state. It's safe to verify disabled
encoders, connectors and dpll's that are not part of the state,
because during modeset connection_mutex is held.
Merge tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.6 rc3:
MMC host:
- sdhci: Fix regression setting power on Trats2 board
- sdhci-pci: Add support and PCI IDs for more Broxton host controllers"
* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
mmc: sdhci: Fix regression setting power on Trats2 board
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C:
- fix a uevent triggered boot problem by removing a useless debug
print
- fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
standard kernel behaviour
- fix a potential division-by-zero error (needed two takes)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: jz4780: really prevent potential division by zero
Revert "i2c: jz4780: prevent potential division by zero"
i2c: jz4780: prevent potential division by zero
i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
i2c: mux: demux-pinctrl: Clean up sysfs attributes
i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE
It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.
You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.
I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.
So my track record is not good enough, and the stars will have to align
better before that one gets committed. And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.
IOW, let's just revert the commit that caused the problem for now.
Merge branch 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Since commit 0de798584bde ("parisc: Use generic extable search and
sort routines") module loading is boken on parisc, because the parisc
module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.
In addition, due to that breakage, Mikulas Patocka noticed that
handling exceptions from modules probably never worked on parisc. It
was just masked by the fact that exceptions from modules don't happen
during normal use.
This patch series fixes those issues and survives the tests of the
lib/test_user_copy kernel module test. Some patches are tagged for
stable"
* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Update comment regarding relative extable support
parisc: Unbreak handling exceptions from kernel modules
parisc: Fix kernel crash with reversed copy_from_user()
parisc: Avoid function pointers for kernel exception routines
parisc: Handle R_PARISC_PCREL32 relocations in kernel modules
Merge tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of four GPIO fixes. The two fixes to the core are
serious as they are regressing minor architectures.
Core fixes:
- Defer GPIO device setup until after gpiolib is initialized.
It turns out that a few very tightly integrated GPIO platform
drivers initialize so early (befor core_initcall()) so that the
gpiolib isn't even initialized itself. That limits what the
library can do, and we cannot reference uninitialized fields until
later.
Defer some of the initialization until right after the gpiolib is
initialized in these (rare) cases.
- As a consequence: do not use devm_* resources when allocating the
states in the initial set-up of the gpiochip.
Driver fixes:
- In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.
- Fix legacy builds on the PXA without a backing pin controller.
- Use correct datatype on pca953x register writes"
* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Use correct u16 value for register word write
gpiolib: Defer gpio device setup until after gpiolib initialization
gpiolib: Do not use devm functions when registering gpio chip
gpio: pxa: fix legacy non pinctrl aware builds
gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Merge tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO driver fixes, along with two staging driver fixes
for 4.6-rc3.
One staging driver patch reverts the deletion of a driver that
happened in 4.6-rc1. We thought that laptop.org was dead, but it's
still alive and kicking, and has users that were mad we broke their
hardware by deleting a driver for their machines. So that driver is
added back and everyone is happy again.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: olpc_dcon: Remove obsolete driver"
staging/rdma/hfi1: select CRC32
iio: gyro: bmg160: fix buffer read values
iio: gyro: bmg160: fix endianness when reading axes
iio: accel: bmc150: fix endianness when reading axes
iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
iio: fix config watermark initial value
iio: health: max30100: correct FIFO check condition
iio: imu: Fix inv_mpu6050 dependencies
iio: adc: Fix build error of missing devm_ioremap_resource on UM
iio: light: apds9960: correct FIFO check condition
iio: adc: max1363: correct reference voltage
iio: adc: max1363: add missing adc to max1363_id
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of eight fixes.
Two are trivial gcc-6 updates (brace additions and unused variable
removal). There's a couple of cxlflash regressions, a correction for
sd being overly chatty on revalidation (causing excess log increases).
A VPD issue which could crash USB devices because they seem very
intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
overrun fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Do not attach VPD to devices that don't support it
sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
scsi_dh_alua: Fix a recently introduced deadlock
scsi: Declare local symbols static
cxlflash: Move to exponential back-off when cmd_room is not available
cxlflash: Fix regression issue with re-ordering patch
mpt3sas: Don't overreach ioc->reply_post[] during initialization
aacraid: add missing curly braces
- fix error handling (Guoqing)
- fix a crash when a disk is hotremoved (me)
- fix a dead loop (Wei Fang)"
* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: clear bitmap if bitmap_create failed
MD: add rdev reference for super write
md: fix a trivial typo in comments
md:raid1: fix a dead loop when read from a WriteMostly disk
Merge tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
from Haishuang Yan.
2) Fix multicast frame handling in mac80211 AP code, from Felix
Fietkau.
3) mac80211 station hashtable insert errors not handled properly, fix
from Johannes Berg.
4) Fix TX descriptor count limit handling in e1000, from Alexander
Duyck.
5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.
6) Must assign rtnl_link_ops of the device before registering it, fix
in ip6_tunnel from Thadeu Lima de Souza Cascardo.
7) Memory leak fix in tc action net exit, from WANG Cong.
8) Add missing AF_KCM entries to name tables, from Dexuan Cui.
9) Fix regression in GRE handling of csums wrt. FOU, from Alexander
Duyck.
10) Fix memory allocation alignment and congestion map corruption in
RDS, from Shamir Rabinovitch.
11) Fix default qdisc regression in tuntap driver, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge, netem: mark mailing lists as moderated
tuntap: restore default qdisc
mpls: find_outdev: check for err ptr in addition to NULL check
ipv6: Count in extension headers in skb->network_header
RDS: fix congestion map corruption for PAGE_SIZE > 4k
RDS: memory allocated must be align to 8
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
net: add the AF_KCM entries to family name tables
MAINTAINERS: intel-wired-lan list is moderated
lib/test_bpf: Add additional BPF_ADD tests
lib/test_bpf: Add test to check for result of 32-bit add that overflows
lib/test_bpf: Add tests for unsigned BPF_JGT
lib/test_bpf: Fix JMP_JSET tests
VSOCK: Detach QP check should filter out non matching QPs.
stmmac: fix adjust link call in case of a switch is attached
af_packet: tone down the Tx-ring unsupported spew.
net_sched: fix a memory leak in tc action
samples/bpf: Enable powerpc support
samples/bpf: Use llc in PATH, rather than a hardcoded value
samples/bpf: Fix build breakage with map_perf_test_user.c
...
Merge branch 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are bug fixes, including a really old fsync bug, and a few trace
points to help us track down problems in the quota code"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file/data loss caused by fsync after rename and new inode
btrfs: Reset IO error counters before start of device replacing
btrfs: Add qgroup tracing
Btrfs: don't use src fd for printk
btrfs: fallback to vmalloc in btrfs_compare_tree
btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
btrfs: Output more info for enospc_debug mount option
Btrfs: fix invalid reference in replace_path
Btrfs: Improve FL_KEEP_SIZE handling in fallocate
Merge tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fixes from Mike Marshall:
"Orangefs cleanups and a strncpy vulnerability fix.
Cleanups:
- remove an unused variable from orangefs_readdir.
- clean up printk wrapper used for ofs "gossip" debugging.
- clean up truncate ctime and mtime setting in inode.c
- remove a useless null check found by coccinelle.
- optimize some memcpy/memset boilerplate code.
- remove some useless sanity checks from xattr.c
Fix:
- fix a potential strncpy vulnerability"
* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: remove unused variable
orangefs: Add KERN_<LEVEL> to gossip_<level> macros
orangefs: strncpy -> strscpy
orangefs: clean up truncate ctime and mtime setting
Orangefs: fix ifnullfree.cocci warnings
Orangefs: optimize boilerplate code.
Orangefs: xattr.c cleanup
Merge tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- compile-time fixes (warnings and failures)
- a bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- fix in scatterlist handling of the ARM common DMA-API code
- stall detection fix for the Rockchip IOMMU driver
* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Silence an uninitialized variable warning
iommu/rockchip: Fix "is stall active" check
iommu: Don't overwrite domain pointer when there is no default_domain
iommu/dma: Restore scatterlist offsets correctly
iommu: provide of_xlate pointer unconditionally
Chris Wilson [Sat, 9 Apr 2016 09:57:57 +0000 (10:57 +0100)]
drm/i915: Replace manual barrier() with READ_ONCE() in HWS accessor
When reading from the HWS page, we use barrier() to prevent the compiler
optimising away the read from the volatile (may be updated by the GPU)
memory address. This is more suited to READ_ONCE(); make it so.
Chris Wilson [Sat, 9 Apr 2016 09:57:56 +0000 (10:57 +0100)]
drm/i915: Use simplest form for flushing the single cacheline in the HWS
Rather than call a function to compute the matching cachelines and
clflush them, just call the clflush *instruction* directly. We also know
that we can use the unpatched plain clflush rather than the clflushopt
alternative.
Chris Wilson [Sat, 9 Apr 2016 09:57:55 +0000 (10:57 +0100)]
drm/i915: Harden detection of missed interrupts
Only declare a missed interrupt if we find that the GPU is idle with
waiters and a hangcheck interval has passed in which no new user
interrupts have been raised.
v2: Clear the stuck interrupt marker between successful batches
Chris Wilson [Sat, 9 Apr 2016 09:57:54 +0000 (10:57 +0100)]
drm/i915: Separate out the seqno-barrier from engine->get_seqno
In order to simplify future patches, extract the
lazy_coherency optimisation our of the engine->get_seqno() vfunc into
its own callback.
v2: Rename the barrier to engine->irq_seqno_barrier to try and better
reflect that the barrier is only required after the user interrupt before
reading the seqno (to ensure that the seqno update lands in time as we
do not have strict seqno-irq ordering on all platforms).
Reviewed-by: Dave Gordon <david.s.gordon@intel.com> [#v2]
v3: Comments for hangcheck paranoia. Mika wanted to keep the extra
barrier inside the hangcheck, just in case. I can argue that it doesn't
provide a barrier against anything, but the side-effects of applying the
barrier may prevent a false declaration of a hung GPU.
Chris Wilson [Sat, 9 Apr 2016 09:57:53 +0000 (10:57 +0100)]
drm/i915: Remove forcewake dance from seqno/irq barrier on legacy gen6+
In order to ensure seqno/irq coherency, we currently read a ring register.
The mmio transaction following the interrupt delays the inspection of
the seqno long enough for the MI_STORE_DWORD_IMM to update the CPU
cache. However, it is only the memory timing that is important for the
purposes of the delay, we do not need nor desire the extra forcewake.
Akash Goel [Fri, 11 Mar 2016 09:26:42 +0000 (14:56 +0530)]
drm/i915: Fixup the free space logic in ring_prepare
Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.
Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.
David S. Miller [Fri, 8 Apr 2016 20:41:28 +0000 (16:41 -0400)]
Merge tag 'mac80211-for-davem-2016-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
For the current RC series, we have the following fixes:
* TDLS fixes from Arik and Ilan
* rhashtable fixes from Ben and myself
* documentation fixes from Luis
* U-APSD fixes from Emmanuel
* a TXQ fix from Felix
* and a compiler warning suppression from Jeff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
parisc: Unbreak handling exceptions from kernel modules
Handling exceptions from modules never worked on parisc.
It was just masked by the fact that exceptions from modules
don't happen during normal use.
When a module triggers an exception in get_user() we need to load the
main kernel dp value before accessing the exception_data structure, and
afterwards restore the original dp value of the module on exit.
parisc: Fix kernel crash with reversed copy_from_user()
The kernel module testcase (lib/test_user_copy.c) exhibited a kernel
crash on parisc if the parameters for copy_from_user were reversed
("illegal reversed copy_to_user" testcase).
Fix this potential crash by checking the fault handler if the faulting
address is in the exception table.
parisc: Avoid function pointers for kernel exception routines
We want to avoid the kernel module loader to create function pointers
for the kernel fixup routines of get_user() and put_user(). Changing
the external reference from function type to int type fixes this.
This unbreaks exception handling for get_user() and put_user() when
called from a kernel module.
Jason Wang [Fri, 8 Apr 2016 05:26:48 +0000 (13:26 +0800)]
tuntap: restore default qdisc
After commit f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes: f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev") Cc: Phil Sutter <phil@nwl.cc> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branches 'pm-core', 'powercap' and 'pm-tools'
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
Merge branches 'pm-cpufreq', 'pm-cpuidle' and 'acpi-cppc'
* pm-cpufreq:
cpufreq: dt: Drop stale comment
cpufreq: intel_pstate: Documenation for structures
cpufreq: intel_pstate: fix inconsistency in setting policy limits
intel_pstate: Avoid extra invocation of intel_pstate_sample()
intel_pstate: Do not set utilization update hook too early
* pm-cpuidle:
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
* acpi-cppc:
mailbox: pcc: Don't access an unmapped memory address space
It would have been possible for a rogue client-core to send in a symlink
target which is not NUL terminated. This returns EIO if the client-core
gives us corrupt data.
Leave debugfs and superblock code as is for now.
Other dcache.c and namei.c strncpy instances are safe because
ORANGEFS_NAME_MAX = NAME_MAX + 1; there is always enough space for a
name plus a NUL byte.
Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
fs/orangefs/orangefs-debugfs.c:130:2-26: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
mpls: find_outdev: check for err ptr in addition to NULL check
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to
find the output device. In case of an error, inet{,6}_fib_lookup_dev()
returns error pointer and dev_get_by_index() returns NULL. But the function
only checks for NULL and thus can end up calling dev_put on an ERR_PTR.
This patch adds an additional check for err ptr after the NULL check.
After patch:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
RTNETLINK answers: Network is unreachable
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wilson [Thu, 7 Apr 2016 06:29:18 +0000 (07:29 +0100)]
drm/i915: Simplify check for idleness in hangcheck
Having fixed the tracking of the engine's last_submitted_seqno, we can
now rely on it for detecting when the engine is idle (and not have to
touch the requests pointer).
Chris Wilson [Thu, 7 Apr 2016 06:29:17 +0000 (07:29 +0100)]
drm/i915: Apply a mb between emitting the request and hangcheck
Seal the request and mark it as pending execution before we submit it to
hardware. We assume that the actual submission cannot fail (that
guarantee is provided by preallocating space in the request for the
submission). As we may inspect this state without holding any locks
during hangcheck we should apply a barrier to ensure that we do
not see a more recent value in the HWS than we are tracking.
Chris Wilson [Thu, 7 Apr 2016 06:29:15 +0000 (07:29 +0100)]
drm/i915: Reset semaphore page for gen8
An oversight is that when we wrap the seqno, we need to reset the hw
semaphore counters to 0. We did this for gen6 and gen7 and forgot to do
so for the new implementation required for gen8 (legacy).
Chris Wilson [Thu, 7 Apr 2016 06:29:13 +0000 (07:29 +0100)]
drm/i915: Move the hw semaphore initialisation from GEM to the engine
Since we are setting engine local values that are tied to the hardware,
move it out of i915_gem_init_seqno() into the intel_ring_init_seqno()
backend, next to where the other hw semaphore registers are written.
v2: Make the explanatory comment about always resetting the semaphores to
0 irrespective of the value of the reset seqno.
Chris Wilson [Thu, 7 Apr 2016 06:29:11 +0000 (07:29 +0100)]
drm/i915: On GPU reset, set the HWS breadcrumb to the last seqno
After the GPU reset and we discard all of the incomplete requests, mark
the GPU as having advanced to the last_submitted_seqno (as having
completed the requests and ready for fresh work). The impact of this is
negligible, as all the requests will be considered completed by this
point, it just brings the HWS into line with expectations for external
viewers.
Yong Li [Wed, 30 Mar 2016 06:49:14 +0000 (14:49 +0800)]
gpio: pca953x: Use correct u16 value for register word write
The current implementation only uses the first byte in val,
the second byte is always 0. Change it to use cpu_to_le16
to write the two bytes into the register
Cc: stable@vger.kernel.org Signed-off-by: Yong Li <sdliyong@gmail.com> Reviewed-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Guenter Roeck [Thu, 31 Mar 2016 15:11:30 +0000 (08:11 -0700)]
gpiolib: Defer gpio device setup until after gpiolib initialization
Since commit ff2b13592299 ("gpio: make the gpiochip a real device"),
attempts to add a gpio chip prior to gpiolib initialization cause
the system to crash. This happens because gpio_bus_type has not been
registered yet. Defer creating gpio devices until after gpiolib has
been initialized to fix the problem.
Cc: Greg Ungerer <gerg@uclinux.org> Cc: Alexandre Courbot <gnurou@gmail.com> Fixes: ff2b13592299 ("gpio: make the gpiochip a real device") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Guenter Roeck [Thu, 31 Mar 2016 15:11:29 +0000 (08:11 -0700)]
gpiolib: Do not use devm functions when registering gpio chip
It is possible that a gpio chip is registered before the gpiolib
initialization code has run. This means we can not use devm_ functions
to allocate memory at that time. Do it the old fashioned way.
Robert Jarzmik [Tue, 29 Mar 2016 08:04:00 +0000 (10:04 +0200)]
gpio: pxa: fix legacy non pinctrl aware builds
In legacy pxa builds, ie. non device-tree and platform-data only builds,
pinctrl is not yet available. As a consequence, the pinctrl gpio
direction change function is a stub, returning always success.
In the current state, the gpio driver direction function believes the
pinctrl direction change was successful, and exits without actually
changing the gpio direction.
This patch changes the logic :
- if the pinctrl direction function fails, gpio direction will report
that failure
- if the pinctrl direction function succeeds, gpio direction is changed
by the gpio driver anyway.
This is sub optimal in the pinctrl aware case, as the gpio direction
will be changed twice: once by pinctrl function and another time by
the gpio direction function.
Yet it should be acceptable in this form, as this is functional for all
pxa platforms (device-tree and platform-data), and moreover changing a
gpio direction is very very seldom, usually in machine initialization,
seldom in drivers probe, and an exception for ac97 reset bug.
Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request") Reported-by: Guenter Roeck <guenter@roeck-us.net> Tested-by: Guenter Roeck <guenter@roeck-us.net> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dmitry Torokhov [Thu, 24 Mar 2016 17:50:25 +0000 (10:50 -0700)]
gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*
When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:
This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.
Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Dan Williams [Fri, 8 Apr 2016 03:02:06 +0000 (20:02 -0700)]
libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
projects / linux-beck.git / log