Kylene Jo Hall [Sun, 8 Jan 2006 09:03:15 +0000 (01:03 -0800)]
[PATCH] tpm: add bios measurement log
According to the TCG specifications measurements or hashes of the BIOS code
and data are extended into TPM PCRS and a log is kept in an ACPI table of
these extensions for later validation if desired. This patch exports the
values in the ACPI table through a security-fs seq_file.
Signed-off-by: Seiji Munetoh <munetoh@jp.ibm.com> Signed-off-by: Stefan Berger <stefanb@us.ibm.com> Signed-off-by: Reiner Sailer <sailer@us.ibm.com> Signed-off-by: Kylene Hall <kjhall@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oleg Nesterov [Sun, 8 Jan 2006 09:03:13 +0000 (01:03 -0800)]
[PATCH] do_coredump() should reset group_stop_count earlier
__group_complete_signal() sets ->group_stop_count in sig_kernel_coredump()
path and marks the target thread as ->group_exit_task. So any thread
except group_exit_task will go to handle_group_stop()->finish_stop().
However, when group_exit_task actually starts do_coredump(), it sets
SIGNAL_GROUP_EXIT, but does not reset ->group_stop_count while killing
other threads. If we have not yet stopped threads in the same thread
group, they all will spin in kernel mode until group_exit_task sends them
SIGKILL, because ->group_stop_count > 0 means:
recalc_sigpending_tsk() never clears TIF_SIGPENDING
get_signal_to_deliver() goes to handle_group_stop()
handle_group_stop() returns when SIGNAL_GROUP_EXIT set
Andrew Morton [Sun, 8 Jan 2006 09:03:05 +0000 (01:03 -0800)]
[PATCH] fix possible PAGE_CACHE_SHIFT overflows
We've had two instances recently of overflows when doing
64_bit_value = (32_bit_value << PAGE_CACHE_SHIFT)
I did a tree-wide grep of `<<.*PAGE_CACHE_SHIFT' and this is the result.
- afs_rxfs_fetch_descriptor.offset is of type off_t, which seems broken.
- jfs and jffs are limited to 4GB anyway.
- reiserfs map_block_for_writepage() takes an unsigned long for the block -
it should take sector_t. (It'll fail for huge filesystems with
blocksize<PAGE_CACHE_SIZE)
- cramfs_read() needs to use sector_t (I think cramsfs is busted on large
filesystems anyway)
- affs is limited in file size anyway.
- I generally didn't fix 32-bit overflows in directory operations.
- arm's __flush_dcache_page() is peculiar. What if the page lies beyond 4G?
Cc: Oleg Drokin <green@linuxhacker.ru> Cc: David Howells <dhowells@redhat.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: <reiserfs-dev@namesys.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Anton Altaparmakov <aia21@cantab.net> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: <linux-fsdevel@vger.kernel.org> Cc: Miklos Szeredi <miklos@szeredi.hu> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@suse.de> Cc: <mike.miller@hp.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Neil Brown <neilb@cse.unsw.edu.au> Cc: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
George Anzinger [Sun, 8 Jan 2006 09:02:48 +0000 (01:02 -0800)]
[PATCH] sigaction should clear all signals on SIG_IGN, not just < 32
While rooting aroung in the signal code trying to understand how to fix the
SIG_IGN ploy (set sig handler to SIG_IGN and flood system with high speed
repeating timers) I came across what, I think, is a problem in sigaction()
in that when processing a SIG_IGN request it flushes signals from 1 to
SIGRTMIN and leaves the rest. Attempt to fix this.
Signed-off-by: George Anzinger <george@mvista.com> Cc: Roland McGrath <roland@redhat.com> Cc: Linus Torvalds <torvalds@osdl.org> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Howells [Sun, 8 Jan 2006 09:02:47 +0000 (01:02 -0800)]
[PATCH] keys: Permit running process to instantiate keys
Make it possible for a running process (such as gssapid) to be able to
instantiate a key, as was requested by Trond Myklebust for NFS4.
The patch makes the following changes:
(1) A new, optional key type method has been added. This permits a key type
to intercept requests at the point /sbin/request-key is about to be
spawned and do something else with them - passing them over the
rpc_pipefs files or netlink sockets for instance.
The uninstantiated key, the authorisation key and the intended operation
name are passed to the method.
(2) The callout_info is no longer passed as an argument to /sbin/request-key
to prevent unauthorised viewing of this data using ps or by looking in
/proc/pid/cmdline.
This means that the old /sbin/request-key program will not work with the
patched kernel as it will expect to see an extra argument that is no
longer there.
A revised keyutils package will be made available tomorrow.
(3) The callout_info is now attached to the authorisation key. Reading this
key will retrieve the information.
(4) A new field has been added to the task_struct. This holds the
authorisation key currently active for a thread. Searches now look here
for the caller's set of keys rather than looking for an auth key in the
lowest level of the session keyring.
This permits a thread to be servicing multiple requests at once and to
switch between them. Note that this is per-thread, not per-process, and
so is usable in multithreaded programs.
The setting of this field is inherited across fork and exec.
(5) A new keyctl function (KEYCTL_ASSUME_AUTHORITY) has been added that
permits a thread to assume the authority to deal with an uninstantiated
key. Assumption is only permitted if the authorisation key associated
with the uninstantiated key is somewhere in the thread's keyrings.
This function can also clear the assumption.
(6) A new magic key specifier has been added to refer to the currently
assumed authorisation key (KEY_SPEC_REQKEY_AUTH_KEY).
(7) Instantiation will only proceed if the appropriate authorisation key is
assumed first. The assumed authorisation key is discarded if
instantiation is successful.
(8) key_validate() is moved from the file of request_key functions to the
file of permissions functions.
(9) The documentation is updated.
From: <Valdis.Kletnieks@vt.edu>
Build fix.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Alexander Zangerl <az@bond.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Howells [Sun, 8 Jan 2006 09:02:45 +0000 (01:02 -0800)]
[PATCH] keys: Discard duplicate keys from a keyring on link
Cause any links within a keyring to keys that match a key to be linked into
that keyring to be discarded as a link to the new key is added. The match is
contingent on the type and description strings being the same.
This permits requests, adds and searches to displace negative, expired,
revoked and dead keys easily. After some discussion it was concluded that
duplicate valid keys should probably be discarded also as they would otherwise
hide the new key.
Since request_key() is intended to be the primary method by which keys are
added to a keyring, duplicate valid keys wouldn't be an issue there as that
function would return an existing match in preference to creating a new key.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Alexander Zangerl <az@bond.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
What's the true meaning of the printk return value? Should it include the
priority prefix length of 3? and what about the timing information? In
both cases it was broken:
NeilBrown [Sun, 8 Jan 2006 09:02:40 +0000 (01:02 -0800)]
[PATCH] Fix overflow tests for compat_sys_fcntl64 locking
When making an fctl locking call through compat_sys_fcntl64 (i.e. a 32bit
app on a 64bit kernel), the syscall can return a locking range that is in
conflict with the queried lock.
If some aspect of this range does not fit in the 32bit structure, something
needs to be done.
The current code is wrong in several respects:
- It returns data to userspace even if no conflict was found
i.e. it should check l_type for F_UNLCK
- It returns -EOVERFLOW too agressively. A lock range covering
the last possible byte of the file (start = COMPAT_OFF_T_MAX,
len = 1) should be possible, but is rejected with the current test.
- A extra-long 'len' should not be a problem. If only that part
of the conflicting lock that would be visible to the 32bit
app needs to be reported to the 32bit app anyway.
This patch addresses those three issues and adds a comment to (hopefully)
record it for posterity.
Note: this patch mainly affects test-cases. Real applications rarely is
ever see the problems.
This patch has been tested (LSB test suite), and works.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Matthew Wilcox <willy@debian.org> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Sun, 8 Jan 2006 09:02:39 +0000 (01:02 -0800)]
[PATCH] Fix some problems with truncate and mtime semantics.
SUS requires that when truncating a file to the size that it currently
is:
truncate and ftruncate should NOT modify ctime or mtime
O_TRUNC SHOULD modify ctime and mtime.
Currently mtime and ctime are always modified on most local
filesystems (side effect of ->truncate) or never modified (on NFS).
With this patch:
ATTR_CTIME|ATTR_MTIME are sent with ATTR_SIZE precisely when
an update of these times is required whether size changes or not
(via a new argument to do_truncate). This allows NFS to do
the right thing for O_TRUNC.
inode_setattr nolonger forces ATTR_MTIME|ATTR_CTIME when the ATTR_SIZE
sets the size to it's current value. This allows local filesystems
to do the right thing for f?truncate.
Also, the logic in inode_setattr is changed a bit so there are two return
points. One returns the error from vmtruncate if it failed, the other
returns 0 (there can be no other failure).
Finally, if vmtruncate succeeds, and ATTR_SIZE is the only change
requested, we now fall-through and mark_inode_dirty. If a filesystem did
not have a ->truncate function, then vmtruncate will have changed i_size,
without marking the inode as 'dirty', and I think this is wrong.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] vgacon: Workaround for resize bug in some chipsets
Reported from Redhat Bugzilla Bug 170450
"I updated to the development kernel and now during boot only the top of the
text is visable. For example the monitor screen the is the lines and I can
only see text in the asterisk area.
[PATCH] use ptrace_get_task_struct in various places
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:31 +0000 (01:02 -0800)]
[PATCH] relayfs: cleanup, change relayfs_file_* to relay_file_*
This patch renames relayfs_file_operations to relay_file_operations, and the
file operations themselves from relayfs_XXX to relay_file_XXX, to make it more
clear that they refer to relay files.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:29 +0000 (01:02 -0800)]
[PATCH] relayfs: add support for global relay buffers
This patch adds the optional is_global outparam to the create_buf_file()
callback. This can be used by clients to create a single global relayfs
buffer instead of the default per-cpu buffers. This was suggested as being
useful for certain debugging applications where it's more convenient to be
able to get all the data from a single channel without having to go to the
bother of dealing with per-cpu files.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:28 +0000 (01:02 -0800)]
[PATCH] relayfs: add support for relay files in other filesystems
This patch adds a couple of callback functions that allow a client to hook
into relay_open()/close() and supply the files that will be used to represent
the channel buffers; the default implementation if no callbacks are defined is
to create the files in relayfs. This is to support the creation and use of
relay files in other filesystems such as debugfs, as implied by the fact that
relayfs_file_operations are exported.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:26 +0000 (01:02 -0800)]
[PATCH] relayfs: use generic_ip for private data
Use inode->u.generic_ip instead of relayfs_inode_info to store pointer to user
data. Clients using relayfs_file_create() to create their own files would
probably more expect their data to be stored in generic_ip; we also intend in
the next set of patches to get rid of relayfs-specific stuff in the file
operations, so we might as well do it here.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:24 +0000 (01:02 -0800)]
[PATCH] relayfs: export relayfs_create_file() with fileops param
This patch adds a mandatory fileops param to relayfs_create_file() and exports
that function so that clients can use it to create files defined by their own
set of file operations, in relayfs. The purpose is to allow relayfs
applications to create their own set of 'control' files alongside their relay
files in relayfs rather than having to create them in /proc or debugfs for
instance. relayfs_create_file() is also used by relay_open_buf() to create
the relay files for a channel. In this case, a pointer to
relayfs_file_operations is passed in, along with a pointer to the buffer
associated with the file.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tom Zanussi [Sun, 8 Jan 2006 09:02:23 +0000 (01:02 -0800)]
[PATCH] relayfs: decouple buffer creation from inode creation
The patch series implementa or fixes 3 things that were specifically requested
or suggested by relayfs users:
- support for non-relay files (patches 1-6)
Currently, the relayfs API only supports the creation of directories
(relayfs_create_dir()) and relay files (relay_open()). These patches adds
support for non-relay files (relayfs_create_file()). This is so relayfs
applications can create 'control files' in relayfs itself rather than in /proc
or via a netlink channel, as is currently done in the relay-app examples.
Basically what this amounts to is exporting relayfs_create_file() with an
additional file_ops param that clients can use to supply file operations for
their own special-purpose files in relayfs.
- make exported relay file ops useful (patches 7-8)
The relayfs relay_file_operations have always been exported, the intent being
to make it possible to create relay files in other filesystems such as
debugfs. The problem, though, is that currently the file operations are too
tightly coupled to relayfs to actually be used for this purpose. This patch
fixes that by adding a couple of callback functions that allow a client to
hook into relay_open()/close() and supply the files that will be used to
represent the channel buffers; the default implementation if no callbacks are
defined is to create the files in relayfs.
- add an option to create global relay buffer (patches 9-10) The file creation
callback also supplies an optional param, is_global, that can be used by
clients to create a single global relayfs buffer instead of the default
per-cpu buffers. This was suggested as being useful for certain debugging
applications where it's more convenient to be able to get all the data from a
single channel without having to go to the bother of dealing with per-cpu
files.
- cleanup, some renaming and Documentation updates (patches 11-12)
There were several comments that the use of netlink in the example code was
non-intuitive and in fact the whole relay-app business was needlessly
confusing. Based on that feedback, the example code has been completely
converted over to relayfs control files as supported by this patch, and have
also been made completely self-contained.
The converted examples along with a couple of new examples that demonstrate
using exported relay files can be found in relay-apps tarball:
http://prdownloads.sourceforge.net/relayfs/relay-apps-0.9.tar.gz?download
This patch:
Separate buffer create/destroy from inode create/destroy. We want to be able
to associate other data and not just relay buffers with inodes. Buffer
create/destroy is moved out of inode.c and into relayfs core code.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Sun, 8 Jan 2006 09:02:17 +0000 (01:02 -0800)]
[PATCH] kernel/: small cleanups
This patch contains the following cleanups:
- make needlessly global functions static
- every file should include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Sun, 8 Jan 2006 09:02:15 +0000 (01:02 -0800)]
[PATCH] move rtc_interrupt() prototype to rtc.h
This patch moves the rtc_interrupt() prototype to rtc.h and removes the
prototypes from C files.
It also renames static rtc_interrupt() functions in
arch/arm/mach-integrator/time.c and arch/sh64/kernel/time.c to avoid compile
problems.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Paul Gortmaker <p_gortmaker@yahoo.com> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OGAWA Hirofumi [Sun, 8 Jan 2006 09:02:14 +0000 (01:02 -0800)]
[PATCH] Fix and add EXPORT_SYMBOL(filemap_write_and_wait)
This patch add EXPORT_SYMBOL(filemap_write_and_wait) and use it.
See mm/filemap.c:
And changes the filemap_write_and_wait() and filemap_write_and_wait_range().
Current filemap_write_and_wait() doesn't wait if filemap_fdatawrite()
returns error. However, even if filemap_fdatawrite() returned an
error, it may have submitted the partially data pages to the device.
(e.g. in the case of -ENOSPC)
<quotation>
Andrew Morton writes,
If filemap_fdatawrite() returns an error, this might be due to some
I/O problem: dead disk, unplugged cable, etc. Given the generally
crappy quality of the kernel's handling of such exceptions, there's a
good chance that the filemap_fdatawait() will get stuck in D state
forever.
</quotation>
So, this patch doesn't wait if filemap_fdatawrite() returns the -EIO.
Trond, could you please review the nfs part? Especially I'm not sure,
nfs must use the "filemap_fdatawrite(inode->i_mapping) == 0", or not.
OGAWA Hirofumi [Sun, 8 Jan 2006 09:02:12 +0000 (01:02 -0800)]
[PATCH] export/change sync_page_range/_nolock()
This exports/changes the sync_page_range/_nolock(). The fatfs needs
sync_page_range/_nolock() for expanding truncate, and changes "size_t count"
to "loff_t count".
OGAWA Hirofumi [Sun, 8 Jan 2006 09:02:11 +0000 (01:02 -0800)]
[PATCH] fat: support ->direct_IO()
This patch add to support of ->direct_IO() for mostly read.
The user of this seems to want to use for streaming read. So, current direct
I/O has limitation, it can only overwrite. (For write operation, mainly we
need to handle the hole etc..)
Russell King [Sun, 8 Jan 2006 09:02:07 +0000 (01:02 -0800)]
[PATCH] IRQ type flags
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tim Schmielau [Sun, 8 Jan 2006 09:02:05 +0000 (01:02 -0800)]
[PATCH] fix more missing includes
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:02:04 +0000 (01:02 -0800)]
[PATCH] cpuset: skip rcu check if task is in root cpuset
For systems that aren't using cpusets, but have them CONFIG_CPUSET enabled in
their kernel (eventually this may be most distribution kernels), this patch
removes even the minimal rcu_read_lock() from the memory page allocation path.
Actually, it removes that rcu call for any task that is in the root cpuset
(top_cpuset), which on systems not actively using cpusets, is all tasks.
We don't need the rcu check for tasks in the top_cpuset, because the
top_cpuset is statically allocated, so at no risk of being freed out from
underneath us.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:02:03 +0000 (01:02 -0800)]
[PATCH] cpuset: mark number_of_cpusets read_mostly
Mark cpuset global 'number_of_cpusets' as __read_mostly.
This global is accessed everytime a zone is considered in the zonelist loops
beneath __alloc_pages, looking for a free memory page. If number_of_cpusets
is just one, then we can short circuit the mems_allowed check.
Since this global is read alot on a hot path, and written rarely, it is an
excellent candidate for __read_mostly.
Thanks to Christoph Lameter for the suggestion.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:02:02 +0000 (01:02 -0800)]
[PATCH] cpuset: use rcu directly optimization
Optimize the cpuset impact on page allocation, the most performance critical
cpuset hook in the kernel.
On each page allocation, the cpuset hook needs to check for a possible change
in the current tasks cpuset. It can now handle the common case, of no change,
without taking any spinlock or semaphore, thanks to RCU.
Convert a spinlock on the current task to an rcu_read_lock(), saving
approximately a memory barrier and an atomic op, depending on architecture.
This is done by adding rcu_assign_pointer() and synchronize_rcu() calls to the
write side of the task->cpuset pointer, in cpuset.c:attach_task(), to delay
freeing up a detached cpuset until after any critical sections referencing
that pointer.
Thanks to Andi Kleen, Nick Piggin and Eric Dumazet for ideas.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:02:01 +0000 (01:02 -0800)]
[PATCH] cpuset: remove test for null cpuset from alloc code path
Remove a couple of more lines of code from the cpuset hooks in the page
allocation code path.
There was a check for a NULL cpuset pointer in the routine
cpuset_update_task_memory_state() that was only needed during system boot,
after the memory subsystem was initialized, before the cpuset subsystem was
initialized, to catch a NULL task->cpuset pointer.
Add a cpuset_init_early() routine, just before the mem_init() call in
init/main.c, that sets up just enough of the init tasks cpuset structure to
render cpuset_update_task_memory_state() calls harmless.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:02:00 +0000 (01:02 -0800)]
[PATCH] cpuset: migrate all tasks in cpuset at once
Given the mechanism in the previous patch to handle rebinding the per-vma
mempolicies of all tasks in a cpuset that changes its memory placement, it is
now easier to handle the page migration requirements of such tasks at the same
time.
The previous code didn't actually attempt to migrate the pages of the tasks in
a cpuset whose memory placement changed until the next time each such task
tried to allocate memory. This was undesirable, as users invoking memory page
migration exected to happen when the placement changed, not some unspecified
time later when the task needed more memory.
It is now trivial to handle the page migration at the same time as the per-vma
rebinding is done.
The routine cpuset.c:update_nodemask(), which handles changing a cpusets
memory placement ('mems') now checks for the special case of being asked to
write a placement that is the same as before. It was harmless enough before
to just recompute everything again, even though nothing had changed. But page
migration is a heavy weight operation - moving pages about. So now it is
worth avoiding that if asked to move a cpuset to its current location.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:59 +0000 (01:01 -0800)]
[PATCH] cpuset: rebind vma mempolicies fix
Fix more of longstanding bug in cpuset/mempolicy interaction.
NUMA mempolicies (mm/mempolicy.c) are constrained by the current tasks cpuset
to just the Memory Nodes allowed by that cpuset. The kernel maintains
internal state for each mempolicy, tracking what nodes are used for the
MPOL_INTERLEAVE, MPOL_BIND or MPOL_PREFERRED policies.
When a tasks cpuset memory placement changes, whether because the cpuset
changed, or because the task was attached to a different cpuset, then the
tasks mempolicies have to be rebound to the new cpuset placement, so as to
preserve the cpuset-relative numbering of the nodes in that policy.
An earlier fix handled such mempolicy rebinding for mempolicies attached to a
task.
This fix rebinds mempolicies attached to vma's (address ranges in a tasks
address space.) Due to the need to hold the task->mm->mmap_sem semaphore while
updating vma's, the rebinding of vma mempolicies has to be done when the
cpuset memory placement is changed, at which time mmap_sem can be safely
acquired. The tasks mempolicy is rebound later, when the task next attempts
to allocate memory and notices that its task->cpuset_mems_generation is
out-of-date with its cpusets mems_generation.
Because walking the tasklist to find all tasks attached to a changing cpuset
requires holding tasklist_lock, a spinlock, one cannot update the vma's of the
affected tasks while doing the tasklist scan. In general, one cannot acquire
a semaphore (which can sleep) while already holding a spinlock (such as
tasklist_lock). So a list of mm references has to be built up during the
tasklist scan, then the tasklist lock dropped, then for each mm, its mmap_sem
acquired, and the vma's in that mm rebound.
Once the tasklist lock is dropped, affected tasks may fork new tasks, before
their mm's are rebound. A kernel global 'cpuset_being_rebound' is set to
point to the cpuset being rebound (there can only be one; cpuset modifications
are done under a global 'manage_sem' semaphore), and the mpol_copy code that
is used to copy a tasks mempolicies during fork catches such forking tasks,
and ensures their children are also rebound.
When a task is moved to a different cpuset, it is easier, as there is only one
task involved. It's mm->vma's are scanned, using the same
mpol_rebind_policy() as used above.
It may happen that both the mpol_copy hook and the update done via the
tasklist scan update the same mm twice. This is ok, as the mempolicies of
each vma in an mm keep track of what mems_allowed they are relative to, and
safely no-op a second request to rebind to the same nodes.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:57 +0000 (01:01 -0800)]
[PATCH] cpuset: number_of_cpusets optimization
Easy little optimization hack to avoid actually having to call
cpuset_zone_allowed() and check mems_allowed, in the main page allocation
routine, __alloc_pages(). This saves several CPU cycles per page allocation
on systems not using cpusets.
A counter is updated each time a cpuset is created or removed, and whenever
there is only one cpuset in the system, it must be the root cpuset, which
contains all CPUs and all Memory Nodes. In that case, when the counter is
one, all allocations are allowed.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:56 +0000 (01:01 -0800)]
[PATCH] cpuset: numa_policy_rebind cleanup
Cleanup, reorganize and make more robust the mempolicy.c code to rebind
mempolicies relative to the containing cpuset after a tasks memory placement
changes.
The real motivator for this cleanup patch is to lay more groundwork for the
upcoming patch to correctly rebind NUMA mempolicies that are attached to vma's
after the containing cpuset memory placement changes.
NUMA mempolicies are constrained by the cpuset their task is a member of.
When either (1) a task is moved to a different cpuset, or (2) the 'mems'
mems_allowed of a cpuset is changed, then the NUMA mempolicies have embedded
node numbers (for MPOL_BIND, MPOL_INTERLEAVE and MPOL_PREFERRED) that need to
be recalculated, relative to their new cpuset placement.
The old code used an unreliable method of determining what was the old
mems_allowed constraining the mempolicy. It just looked at the tasks
mems_allowed value. This sort of worked with the present code, that just
rebinds the -task- mempolicy, and leaves any -vma- mempolicies broken,
referring to the old nodes. But in an upcoming patch, the vma mempolicies
will be rebound as well. Then the order in which the various task and vma
mempolicies are updated will no longer be deterministic, and one can no longer
count on the task->mems_allowed holding the old value for as long as needed.
It's not even clear if the current code was guaranteed to work reliably for
task mempolicies.
So I added a mems_allowed field to each mempolicy, stating exactly what
mems_allowed the policy is relative to, and updated synchronously and reliably
anytime that the mempolicy is rebound.
Also removed a useless wrapper routine, numa_policy_rebind(), and had its
caller, cpuset_update_task_memory_state(), call directly to the rewritten
policy_rebind() routine, and made that rebind routine extern instead of
static, and added a "mpol_" prefix to its name, making it
mpol_rebind_policy().
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:55 +0000 (01:01 -0800)]
[PATCH] cpuset: implement cpuset_mems_allowed
Provide a cpuset_mems_allowed() method, which the sys_migrate_pages() code
needed, to obtain the mems_allowed vector of a cpuset, and replaced the
workaround in sys_migrate_pages() to call this new method.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:54 +0000 (01:01 -0800)]
[PATCH] cpuset: combine refresh_mems and update_mems
The important code paths through alloc_pages_current() and alloc_page_vma(),
by which most kernel page allocations go, both called
cpuset_update_current_mems_allowed(), which in turn called refresh_mems().
-Both- of these latter two routines did a tasklock, got the tasks cpuset
pointer, and checked for out of date cpuset->mems_generation.
That was a silly duplication of code and waste of CPU cycles on an important
code path.
Consolidated those two routines into a single routine, called
cpuset_update_task_memory_state(), since it updates more than just
mems_allowed.
Changed all callers of either routine to call the new consolidated routine.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:53 +0000 (01:01 -0800)]
[PATCH] cpuset: fork hook fix
Fix obscure, never seen in real life, cpuset fork race. The cpuset_fork()
call in fork.c was setting up the correct task->cpuset pointer after the
tasklist_lock was dropped, which briefly exposed the newly forked process with
an unsafe (copied from parent without locks or usage counter increment) cpuset
pointer.
In theory, that exposed cpuset pointer could have been pointing at a cpuset
that was already freed and removed, and in theory another task that had been
sitting on the tasklist_lock waiting to scan the task list could have raced
down the entire tasklist, found our new child at the far end, and dereferenced
that bogus cpuset pointer.
To fix, setup up the correct cpuset pointer in the new child by calling
cpuset_fork() before the new task is linked into the tasklist, and with that,
add a fork failure case, to dereference that cpuset, if the fork fails along
the way, after cpuset_fork() was called.
Had to remove a BUG_ON() from cpuset_exit(), because it was no longer valid -
the call to cpuset_exit() from a failed fork would not have PF_EXITING set.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:52 +0000 (01:01 -0800)]
[PATCH] cpuset: update_nodemask code reformat
Restructure code layout of the kernel/cpuset.c update_nodemask() routine,
removing embedded returns and nested if's in favor of goto completion labels.
This is being done in anticipation of adding more logic to this routine, which
will favor the goto style structure.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:51 +0000 (01:01 -0800)]
[PATCH] cpuset: remove marker_pid documentation
Remove documentation for the cpuset 'marker_pid' feature, that was in the
patch "cpuset: change marker for relative numbering" That patch was previously
pulled from *-mm at my (pj) request.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:49 +0000 (01:01 -0800)]
[PATCH] cpuset: memory pressure meter
Provide a simple per-cpuset metric of memory pressure, tracking the -rate-
that the tasks in a cpuset call try_to_free_pages(), the synchronous
(direct) memory reclaim code.
This enables batch managers monitoring jobs running in dedicated cpusets to
efficiently detect what level of memory pressure that job is causing.
This is useful both on tightly managed systems running a wide mix of
submitted jobs, which may choose to terminate or reprioritize jobs that are
trying to use more memory than allowed on the nodes assigned them, and with
tightly coupled, long running, massively parallel scientific computing jobs
that will dramatically fail to meet required performance goals if they
start to use more memory than allowed to them.
This patch just provides a very economical way for the batch manager to
monitor a cpuset for signs of memory pressure. It's up to the batch
manager or other user code to decide what to do about it and take action.
==> Unless this feature is enabled by writing "1" to the special file
/dev/cpuset/memory_pressure_enabled, the hook in the rebalance
code of __alloc_pages() for this metric reduces to simply noticing
that the cpuset_memory_pressure_enabled flag is zero. So only
systems that enable this feature will compute the metric.
Why a per-cpuset, running average:
Because this meter is per-cpuset, rather than per-task or mm, the
system load imposed by a batch scheduler monitoring this metric is
sharply reduced on large systems, because a scan of the tasklist can be
avoided on each set of queries.
Because this meter is a running average, instead of an accumulating
counter, a batch scheduler can detect memory pressure with a single
read, instead of having to read and accumulate results for a period of
time.
Because this meter is per-cpuset rather than per-task or mm, the
batch scheduler can obtain the key information, memory pressure in a
cpuset, with a single read, rather than having to query and accumulate
results over all the (dynamically changing) set of tasks in the cpuset.
A per-cpuset simple digital filter (requires a spinlock and 3 words of data
per-cpuset) is kept, and updated by any task attached to that cpuset, if it
enters the synchronous (direct) page reclaim code.
A per-cpuset file provides an integer number representing the recent
(half-life of 10 seconds) rate of direct page reclaims caused by the tasks
in the cpuset, in units of reclaims attempted per second, times 1000.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:47 +0000 (01:01 -0800)]
[PATCH] cpuset: mempolicy one more nodemask conversion
Finish converting mm/mempolicy.c from bitmaps to nodemasks. The previous
conversion had left one routine using bitmaps, since it involved a
corresponding change to kernel/cpuset.c
Fix that interface by replacing with a simple macro that calls nodes_subset(),
or if !CONFIG_CPUSET, returns (1).
Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Christoph Lameter <christoph@lameter.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Sun, 8 Jan 2006 09:01:46 +0000 (01:01 -0800)]
[PATCH] cpuset: better bitmap remap defaults
Fix the default behaviour for the remap operators in bitmap, cpumask and
nodemask.
As previously submitted, the pair of masks <A, B> defined a map of the
positions of the set bits in A to the corresponding bits in B. This is still
true.
The issue is how to map the other positions, corresponding to the unset (0)
bits in A. As previously submitted, they were all mapped to the first set bit
position in B, a constant map.
When I tried to code per-vma mempolicy rebinding using these remap operators,
I realized this was wrong.
This patch changes the default to map all the unset bit positions in A to the
same positions in B, the identity map.
For example, if A has bits 4-7 set, and B has bits 9-12 set, then the map
defined by the pair <A, B> maps each bit position in the first 32 bits as
follows:
This now corresponds to the typical behaviour desired when migrating pages and
policies from one cpuset to another.
The pages on nodes within the original cpuset, and the references in memory
policies to nodes within the original cpuset, are migrated to the
corresponding cpuset-relative nodes in the destination cpuset. Other pages
and node references are left untouched.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Mackall [Sun, 8 Jan 2006 09:01:45 +0000 (01:01 -0800)]
[PATCH] slob: introduce the SLOB allocator
configurable replacement for slab allocator
This adds a CONFIG_SLAB option under CONFIG_EMBEDDED. When CONFIG_SLAB is
disabled, the kernel falls back to using the 'SLOB' allocator.
SLOB is a traditional K&R/UNIX allocator with a SLAB emulation layer,
similar to the original Linux kmalloc allocator that SLAB replaced. It's
signicantly smaller code and is more memory efficient. But like all
similar allocators, it scales poorly and suffers from fragmentation more
than SLAB, so it's only appropriate for small systems.
It's been tested extensively in the Linux-tiny tree. I've also
stress-tested it with make -j 8 compiles on a 3G SMP+PREEMPT box (not
recommended).
Here's a comparison for otherwise identical builds, showing SLOB saving
nearly half a megabyte of RAM:
$ size vmlinux*
text data bss dec hex filename 3336372 529360 190812 4056544 3de5e0 vmlinux-slab 3323208 527948 190684 4041840 3dac70 vmlinux-slob
$ size mm/{slab,slob}.o
text data bss dec hex filename
13221 752 48 14021 36c5 mm/slab.o
1896 52 8 1956 7a4 mm/slob.o
Nick Piggin [Sun, 8 Jan 2006 09:01:41 +0000 (01:01 -0800)]
[PATCH] radix tree: early termination of tag clearing
Correctly determine the tags to be cleared in radix_tree_delete() so we
don't keep moving up the tree clearing tags that we don't need to. For
example, if a tag is simply not set in the deleted item, nor anywhere up
the tree, radix_tree_delete() would attempt to clear it up the entire
height of the tree.
Also, tag_set() was made conditional so as not to dirty too many cachelines
high up in the radix tree. Instead, put this logic into
radix_tree_tag_set().
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some simplification in checking signal delivery against concurrent exit.
Instead of using get_task_struct_rcu(), which increments the task_struct
reference count, check the reference count after acquiring sighand lock.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ingo Molnar [Sun, 8 Jan 2006 09:01:37 +0000 (01:01 -0800)]
[PATCH] RCU signal handling
RCU tasklist_lock and RCU signal handling: send signals RCU-read-locked
instead of tasklist_lock read-locked. This is a scalability improvement on
SMP and a preemption-latency improvement under PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: William Irwin <wli@holomorphy.com> Cc: Roland McGrath <roland@redhat.com> Cc: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Applying RCU to the task structure broke oprofile, because
free_task_notify() can now be called from softirq. This means that the
task_mortuary lock must be acquired with irq disabled in order to avoid
intermittent self-deadlock. Since irq is now disabled, the critical
section within process_task_mortuary() has been restructured to be O(1) in
order to maximize scalability and minimize realtime latency degradation.
Kudos to Wu Fengguang for finding this problem!
CC: Wu Fengguang <wfg@mail.ustc.edu.cn> Cc: Philippe Elie <phil.el@wanadoo.fr> Cc: John Levon <levon@movementarian.org> Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Sun, 8 Jan 2006 09:01:34 +0000 (01:01 -0800)]
[PATCH] uml: prevent MODE_SKAS=n and MODE_TT=n
If MODE_TT=n, MODE_SKAS must be y.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sun, 8 Jan 2006 09:01:33 +0000 (01:01 -0800)]
[PATCH] uml: whitespace cleanup
This fixes some mangled whitespace added by the earlier trap_user.c patch.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sun, 8 Jan 2006 09:01:32 +0000 (01:01 -0800)]
[PATCH] consolidate asm/futex.h
Most of the architectures have the same asm/futex.h. This consolidates them
into asm-generic, with the arches including it from their own asm/futex.h.
In the case of UML, this reverts the old broken futex.h and goes back to using
the same one as almost everyone else.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Change maxaligned_in_smp alignemnt macros to internodealigned_in_smp macros
____cacheline_maxaligned_in_smp is currently used to align critical structures
and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find
L1_CACHE_SHIFT_MAX useless.
However, we have been using ____cacheline_maxaligned_in_smp to align
structures on the internode cacheline size. As per Andi's suggestion,
following patch kills ____cacheline_maxaligned_in_smp and introduces
INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches.
Arches needing L3/Internode cacheline alignment can define
INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces
____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp
David Howells [Sun, 8 Jan 2006 09:01:23 +0000 (01:01 -0800)]
[PATCH] frv: force serial driver inclusion
Force the 8230 serial driver to be built in if the on-CPU UARTs are to be
used. It can't be used as a module because the arch setup needs to call into
it.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / mv-sheeva.git / log