Lydia Wang [Sat, 10 Oct 2009 11:07:52 +0000 (19:07 +0800)]
ALSA: HDA VIA: Add smart5.1 function.
Smart 5.1 is for 3-jacks model, to reuse input pins as outputs.
While off, they act as "line out" / "line in" / "mic in".
While on, they acts as "line out" / "back left/right" / "center/lfe".
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn> Signed-off-by: Logan Li <loganli@viatech.com.cn> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lydia Wang [Sat, 10 Oct 2009 11:07:43 +0000 (19:07 +0800)]
ALSA: HDA VIA: Change VT1708S & VT1702 hp mode controls
For VT1708S and VT1702, deactivate "Headphone Playback Volume" and
"Headphone Playback Mute" control if "Independent HP" mode is OFF.
and rename VT1702 "Independent HP" text.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn> Signed-off-by: Logan Li <loganli@viatech.com.cn> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 9 Oct 2009 15:44:08 +0000 (17:44 +0200)]
ALSA: hda - Add full rates/formats support for Nvidia HDMI
Allow Nvidia HDMI to support more possible sample rates and formats.
At best, the really supported rates and formats should be determined
together with the negotiation with the HDMI receiver, but it's currently
not implemented yet (Nvidia stuff seems incompatible with HDMI 1.3
standard in this regard). As a compromise, we enable all bits, assuming
that all recent devices do support such rates/formats.
Tested-by: Alan Alan <alanwww1@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 7 Oct 2009 13:12:27 +0000 (15:12 +0200)]
ALSA: hda - Fix yet another auto-mic bug in ALC268
Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w
design different from other siblings), it needs to call fixup_automic_adc()
explicitly to set up the auto-mic routing. Otherwise the indices for
int/ext mics aren't set properly.
Takashi Iwai [Tue, 6 Oct 2009 11:21:54 +0000 (13:21 +0200)]
ALSA: hda - Don't pick up invalid HP pins in alc_subsystem_id()
alc_subsystem_id() tries to pick up a headphone pin if not configured,
but this caused side-effects as the problem in commit 15870f05e90a365f8022da416e713be0c5024e2f.
This patch fixes the driver behavior to pick up invalid HP pins; at least,
the pins that are listed as the primary outputs aren't taken any more.
Takashi Iwai [Mon, 5 Oct 2009 06:25:13 +0000 (08:25 +0200)]
ALSA: hda - Fix invalid initializations for ALC861 auto mode
The recent auto-parser doesn't work for machines with a single output
with ALC861, such as Toshiba laptops, because alc_subsystem_id() sets
the hp_pins[0] while it's listed in line_outs[0].
This ends up with the doubled initialization of the same mixer widget,
and it mutes the DAC route because hp_pins has no DAC assigned.
To fix this problem, just check spec->autocfg.hp_outs and speaker_outs
so that they are really detected pins.
Takashi Iwai [Fri, 2 Oct 2009 07:03:58 +0000 (09:03 +0200)]
ALSA: hda - Fix / improve ALC66x parser
The auto-parser for ALC662/663/272 codecs doesn't work properly when
a speaker is connected to mono NID 0x17, and doesn't handle the dynamic
DAC assignment properly.
This patch fixes the issues and also improves the assignment of DACs
so that HP and speakers can have independent volume controls.
Takashi Iwai [Thu, 1 Oct 2009 14:38:11 +0000 (16:38 +0200)]
ALSA: hda - Fix digita/analog mic auto-switching with IDT codecs
When the auto-mic switching between an analog and a digital mic is
needed with IDT codecs, the current driver doesn't reset the connection
of the digital mux.
This patch fixes the behavior by checking both mux connections properly.
ALSA: hda - Resurrect input-source mixer of ALC268 model=acer
In the commit fdbc66266c21976027938642f60e0f047149a61a, I mistakenly
replaced the capture mixer array for ALC268_ACER to nosrc version
although this should be kept to alt_mixer. Now fixed back.
.. duplicated by merging the same fix twice, for details see commit 0d9df2515dbceb67d343c0f10fd3ff218380d524 ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes")
tty: make the kref destructor occur asynchronously
Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:
INIT open /dev/console Input/output error
It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229
The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.
Fix it as per the following Alan's suggestion:
Fun but it's actually not a bug and the fix is wrong in itself as
the port may be closing but not yet being destructed, in which case
it seems to do the wrong thing. Opening a tty that is closing (and
could be closing for long periods) is supposed to return -EIO.
I suspect a better way to deal with this and keep the old console
timing is to split tty->shutdown into two functions.
tty->shutdown() - called synchronously just before we dump the tty
onto the waitqueue for destruction
tty->cleanup() - called when the destructor runs.
We would then do the shutdown part which can occur in IRQ context
fine, before queueing the rest of the release (from tty->magic = 0
... the end) to occur asynchronously
The USB update in -next would then need a call like
if (tty->cleanup)
tty->cleanup(tty);
at the top of the async function and the USB shutdown to be split
between shutdown and cleanup as the USB resource cleanup and final
tidy cannot occur synchronously as it needs to sleep.
In other words the logic becomes
final kref put
make object unfindable
async
clean it up
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ] Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
comments from Alan Stern - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3d5b6fb47a8e68fa311ca2c3447e7f8a7c3a9cf3 ("ACPI: Kill overly
verbose "power state" log messages") removed the actual use of this
variable, but didn't remove the variable itself, resulting in build
warnings like
drivers/acpi/processor_idle.c: In function ‘acpi_processor_power_init’:
drivers/acpi/processor_idle.c:1169: warning: unused variable ‘i’
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix hwpoison code related build failure on 32-bit NUMAQ
I was recently lucky enough to get a 64-CPU system, so my kernel log
ends up with 64 lines like:
ACPI: CPU0 (power states: C1[C1] C2[C3])
This is pretty useless clutter because this info is already available
after boot from both /sys/devices/system/cpu/cpu*/cpuidle/state?/ as
well as /proc/acpi/processor/CPU*/power.
So just delete the code that prints the C-states in processor_idle.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Len Brown <len.brown@intel.com>
x86: Fix hwpoison code related build failure on 32-bit NUMAQ
This build failure triggers:
In file included from include/linux/suspend.h:8,
from arch/x86/kernel/asm-offsets_32.c:11,
from arch/x86/kernel/asm-offsets.c:2:
include/linux/mm.h:503:2: error: #error SECTIONS_WIDTH+NODES_WIDTH+ZONES_WIDTH > BITS_PER_LONG - NR_PAGEFLAGS
Because due to the hwpoison page flag we ran out of page
flags on 32-bit.
Dont turn on hwpoison on 32-bit NUMA (it's rare in any
case).
Also clean up the Kconfig dependencies in the generic MM
code by introducing ARCH_SUPPORTS_MEMORY_FAILURE.
Jean Delvare [Tue, 8 Sep 2009 13:31:46 +0000 (15:31 +0200)]
ACPI: Clarify resource conflict message
The message "ACPI: Device needs an ACPI driver" is misleading. The
device _may_ need an ACPI driver, if the BIOS implemented a custom
API for the device in question (which, AFAIK, can't be checked.) If
not, then either a generic ACPI driver may be used (for example
"thermal"), or nothing can be done (other than a white list).
I propose to reword the message to:
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
which I think is more correct. Comments and suggestions welcome.
I also added a message warning about possible problems and system
instability when users pass acpi_enforce_resources=lax, as suggested
by Len.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Thomas Renninger <trenn@suse.de> Cc: Alan Jenkins <sourcejedi.lkml@googlemail.com> Signed-off-by: Len Brown <len.brown@intel.com>
thinkpad-acpi: fix CONFIG_THINKPAD_ACPI_HOTKEY_POLL build problem
Fix this problem when CONFIG_THINKPAD_ACPI_HOTKEY_POLL is undefined:
CHECK drivers/platform/x86/thinkpad_acpi.c
drivers/platform/x86/thinkpad_acpi.c:1968:21: error: not an lvalue
CC [M] drivers/platform/x86/thinkpad_acpi.o
drivers/platform/x86/thinkpad_acpi.c: In function 'tpacpi_hotkey_driver_mask_set':
drivers/platform/x86/thinkpad_acpi.c:1968: error: lvalue required as left operand of assignment
Reported-by: Noah Dain <noahdain@gmail.com> Reported-by: Audrius Kazukauskas <audrius@neutrino.lt> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: new driver for ADP5520/ADP5501 MFD PMICs
backlight: extend event support to also support poll()
backlight/eeepc-laptop: Update the backlight state when we change brightness
backlight/acpi: Update the backlight state when we change brightness
backlight: Allow drivers to update the core, and generate events on changes
backlight: switch to da903x driver to dev_pm_ops
backlight: Add support for the Avionic Design Xanthos backlight device.
backlight: spi driver for LMS283GF05 LCD
backlight: move hp680-bl's probe function to .devinit.text
backlight: Add support for new Apple machines.
backlight: mbp_nvidia_bl: add support for MacBookAir 1,1
backlight: Add WM831x backlight driver
Trivial conflicts due to '#ifdef CONFIG_PM' differences in
drivers/video/backlight/da903x_bl.c
* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Resume clocksource without taking the clocksource mutex
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
modules, tracing: Remove stale struct marker signature from module_layout()
tracing/workqueue: Use %pf in workqueue trace events
tracing: Fix a comment and a trivial format issue in tracepoint.h
tracing: Fix failure path in ftrace_regex_open()
tracing: Fix failure path in ftrace_graph_write()
tracing: Check the return value of trace_get_user()
tracing: Fix off-by-one in trace_get_user()
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove redundant non-NUMA topology functions
x86: early_printk: Protect against using the same device twice
x86: Reduce verbosity of "PAT enabled" kernel message
x86: Reduce verbosity of "TSC is reliable" message
x86: mce: Use safer ways to access MCE registers
x86: mce, inject: Use real inject-msg in raise_local
x86: mce: Fix thermal throttling message storm
x86: mce: Clean up thermal throttling state tracking code
x86: split NX setup into separate file to limit unstack-protected code
xen: check EFER for NX before setting up GDT mapping
x86: Cleanup linker script using new linker script macros.
x86: Use section .data.page_aligned for the idt_table.
x86: convert to use __HEAD and HEAD_TEXT macros.
x86: convert compressed loader to use __HEAD and HEAD_TEXT macros.
x86: fix fragile computation of vsyscall address
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (32 commits)
ACPI: i2c-scmi: don't use acpi_device_uid()
ACPI: simplify building device HID/CID list
ACPI: remove acpi_device_uid() and related stuff
ACPI: remove acpi_device.flags.hardware_id
ACPI: remove acpi_device.flags.compatible_ids
ACPI: maintain a single list of _HID and _CID IDs
ACPI: make sure every acpi_device has an ID
ACPI: use acpi_device_hid() when possible
ACPI: fix synthetic HID for \_SB_
ACPI: handle re-enumeration, when acpi_devices might already exist
ACPI: factor out device type and status checking
ACPI: add acpi_bus_get_status_handle()
ACPI: use acpi_walk_namespace() to enumerate devices
ACPI: identify device tree root by null parent pointer, not ACPI_BUS_TYPE
ACPI: enumerate namespace before adding functional fixed hardware devices
ACPI: convert acpi_bus_scan() to operate on an acpi_handle
ACPI: add acpi_bus_get_parent() and remove "parent" arguments
ACPI: remove unnecessary argument checking
ACPI: remove redundant "type" arguments
ACPI: remove acpi_device_set_context() "type" argument
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix locking and list handling code in cifs_open and its helper
[CIFS] Remove build warning
cifs: fix problems with last two commits
[CIFS] Fix build break when keys support turned off
cifs: eliminate cifs_init_private
cifs: convert oplock breaks to use slow_work facility (try #4)
cifs: have cifsFileInfo hold an extra inode reference
cifs: take read lock on GlobalSMBSes_lock in is_valid_oplock_break
cifs: remove cifsInodeInfo.oplockPending flag
cifs: fix oplock request handling in posix codepath
[CIFS] Re-enable Lanman security
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
at91_can: Forgotten git 'add' of at91_can.c
TI Davinci EMAC: Fix in vector definition for EMAC_VERSION_2
ax25: Fix ax25_cb refcounting in ax25_ctl_ioctl
virtio_net: Check for room in the vq before adding buffer
virtio_net: avoid (most) NETDEV_TX_BUSY by stopping queue early.
virtio_net: formalize skb_vnet_hdr
virtio_net: don't free buffers in xmit ring
virtio_net: return NETDEV_TX_BUSY instead of queueing an extra skb.
virtio_net: skb_orphan() and nf_reset() in xmit path.
Nicolas Pitre [Fri, 25 Sep 2009 20:28:02 +0000 (16:28 -0400)]
make Linux bootable on ARM again
Commit 200b812d00 "Clear the exclusive monitor when returning from an
exception" broke the vast majority of ARM systems in the wild which are
still pre ARMv6. The kernel is crashing on the first occurrence of an
exception due to the removal of the actual return instruction for them.
Let's add it back.
writeback: pass in super_block to bdi_start_writeback()
Sometimes we only want to write pages from a specific super_block,
so allow that to be passed in.
This fixes a problem with commit 56a131dcf7ed36c3c6e36bea448b674ea85ed5bb
causing writeback on all super_blocks on a bdi, where we only really
want to sync a specific sb from writeback_inodes_sb().
TI Davinci EMAC: Fix in vector definition for EMAC_VERSION_2
In the emac_poll function when looking for interrupt status masks
correct definition must be chosen based on EMAC_VERSION(the bit
mask has changed from version 1 to version 2).
Signed-off-by: Sriram <srk@ti.com> Acked-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use ax25_cb_put after ax25_find_cb in ax25_ctl_ioctl.
Reported-by: Bernard Pidoux F6BVP <f6bvp@free.fr> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Reviewed-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Every acpi_device has at least one ID (if there's no _HID or _CID, we
give it a synthetic or default ID). So there's no longer a need to
check whether an ID exists; we can just use it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
There's no need to treat _HID and _CID differently. Keeping them in
a single list makes code that uses the IDs a little simpler because it
can just traverse the list rather than checking "do we have a HID?",
"do we have any CIDs?"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Reviewed-by: Alex Chiang <achiang@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
This makes sure every acpi_device has at least one ID. If we build an
acpi_device for a namespace node with no _HID or _CID, we sometimes
synthesize an ID like "LNXCPU" or "LNXVIDEO". If we don't even have
that, give it a default "device" ID.
Note that this means things like:
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/HWP0001:00/HWP0002:04/device:00
(a PCI slot SxFy device) will have "hid" and "modprobe" entries, where
they didn't before. These aren't very useful (a HID of "device" doesn't
tell you what *kind* of device it is, so it doesn't help find a driver),
but I don't think they're harmful.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
This makes \_SB_ show up as /sys/devices/LNXSYSTM:00/LNXSYBUS:00
rather than "device:00". This has been broken for a loooong time
(at least since 2.6.13) because device->parent is an acpi_device
pointer, not a handle.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: handle re-enumeration, when acpi_devices might already exist
acpi_bus_scan() traverses the namespace to enumerate devices and uses
acpi_add_single_object() to create acpi_devices. When the platform
notifies us of a hot-plug event, we need to traverse part of the namespace
again to figure out what appeared or disappeared. (We don't yet call
acpi_bus_scan() during hot-plug, but I plan to do that in the future.)
This patch makes acpi_add_single_object() notice when we already have
an acpi_device, so we don't need to make a new one.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds acpi_bus_type_and_status(), which determines the type
of the object and whether we want to build an acpi_device for it. If
it is acpi_device-worthy, it returns the type and the device's current
status.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
Add acpi_bus_get_status_handle() so we can get the status of a namespace
object before building a struct acpi_device.
This removes a use of "device->flags.dynamic_status", a cached indicator of
whether _STA exists. It seems simpler and more reliable to just evaluate
_STA and catch AE_NOT_FOUND errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: use acpi_walk_namespace() to enumerate devices
acpi_bus_scan() currently walks the namespace manually. This patch changes
it to use acpi_walk_namespace() instead.
Besides removing some complicated code, this means we take advantage of the
namespace locking done by acpi_walk_namespace(). The locking isn't so
important at boot-time, but I hope to eventually use this same path to
handle hot-addition of devices, when it will be important.
Note that acpi_walk_namespace() does not actually visit the starting node
first, so we need to do that by hand first.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: identify device tree root by null parent pointer, not ACPI_BUS_TYPE
We can identify the root of the ACPI device tree by the fact that it
has no parent. This is simpler than passing around ACPI_BUS_TYPE_SYSTEM
and will help remove special treatment of the device tree root.
Currently, we add the root by hand with ACPI_BUS_TYPE_SYSTEM. If we
traverse the tree treating the root as just another device and use
acpi_get_type(), the root shows up as ACPI_TYPE_DEVICE.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: enumerate namespace before adding functional fixed hardware devices
This patch changes the order so we enumerate in the "root, namespace,
functional fixed" order instead of the "root, functional fixed, namespace"
order. When I change acpi_bus_scan() to use acpi_walk_namespace(), it
will use the former order, so this patch isolates the order change for
bisectability.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: convert acpi_bus_scan() to operate on an acpi_handle
This patch changes acpi_bus_scan() to take an acpi_handle rather than an
acpi_device pointer. I plan to use acpi_bus_scan() in the hotplug path,
and I'd rather not assume that notifications only go to nodes that already
have acpi_devices.
This will also help remove the special case for adding the root node. We
currently add the root by hand before acpi_bus_scan(), but using a handle
here means we can start the acpi_bus_scan() directly with the root even
though it doesn't have an acpi_device yet.
Note that acpi_bus_scan() currently adds and/or starts the *children* of
its device argument. It doesn't do anything with the device itself.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
acpi_add_single_object() is static, and all callers supply a valid "child"
argument, so we don't need to check it. This patch also remove some
unnecessary initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
We only pass the "type" to acpi_device_set_context() so we know whether
the device has a handle to which we can attach the acpi_device pointer.
But it's safer to just check for the handle directly, since it's in the
acpi_device already.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
projects / linux-beck.git / log