Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Cc: Tejun Heo <tj@kernel.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13357/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.
MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13349/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13348/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the cases missed with commit 9b26616c8d9d ("MIPS: Respect the
ISA level in FCSR handling") and prevent writes to read-only FCSR bits
there.
This in particular applies to FP context initialisation where any IEEE
754-2008 bits preset by `mips_set_personality_nan' are cleared before
the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request
addressing FPC_CSR where no masking of read-only FCSR bits is done.
Remove the FCSR clearing from FP context initialisation then and unify
PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out
code from `ptrace_setfpregs' and calling it from both places.
This mostly matters to soft float configurations where the emulator can
be switched this way to a mode which should not be accessible and cannot
be set with the CTC1 instruction. With hard float configurations any
effect is transient anyway as read-only bits will retain their values at
the time the FP context is restored.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13239/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a floating-point context restoration regression introduced with
commit 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling")
that causes a Floating Point exception and consequently a kernel oops
with hard float configurations when one or more FCSR Enable and their
corresponding Cause bits are set both at a time via a ptrace(2) call.
To do so reinstate Cause bit masking originally introduced with commit b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause bits") to
address this exact problem and then inadvertently removed from the
PTRACE_SETFPREGS request with the commit referred above.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13238/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whilst a PR_SET_FP_MODE prctl is performed there are decisions made
based upon whether the task is executing on the current CPU. This may
change if we're preempted, so disable preemption to avoid such changes
for the lifetime of the mode switch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS") Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13144/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then
it will only keep 64 bits per FP register in thread context, and the
calls to set_fpr64 in restore_msa_extcontext will overrun the end of the
FP register context into the FCSR & MSACSR values. GCC 6.x has become
smart enough to detect this & complain like so:
arch/mips/kernel/signal.c: In function 'protected_restore_fp_context':
./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds]
fpr->val##width[FPR_IDX(width, idx)] = val; \
~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS'
BUILD_FPR_ACCESS(64)
The only way to trigger this code to run would be for a program to set
up an artificial extended MSA context structure following a sigframe &
execute sigreturn. Whilst this doesn't allow a program to write to any
state that it couldn't already, it makes little sense to allow this
"restoration" of MSA context in a system that doesn't support MSA.
Fix this by killing a program with SIGSYS if it tries something as crazy
as "restoring" fake MSA context in this way, also fixing the build error
& allowing for most of restore_msa_extcontext to be optimised out of
kernels without support for MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: Michal Toman <michal.toman@imgtec.com> Fixes: bf82cb30c7e5 ("MIPS: Save MSA extended context around signals") Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: James Hogan <james.hogan@imgtec.com> Cc: Michal Toman <michal.toman@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13164/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSA ld_*/st_* assembler macros for when the toolchain doesn't
support MSA use addu to offset the base address. However it is a virtual
memory pointer so fix it to use PTR_ADDU which expands to daddu for
64-bit kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13062/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:
arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'
Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13061/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to datasheet, reserving 0xff800000~0xffffffff (8MB below 4GB) is
not enough for RS780E integrated GPU's TOM (top of memory) registers
and MSI/MSI-x memory region, so we reserve 0xfe000000~0xffffffff (32MB
below 4GB).
After commit 92923ca3aacef63c92d ("mm: meminit: only set page reserved
in the memblock region"), the MIPS hibernation is broken. Because pages
in nosave data section should be "reserved", but currently they aren't
set to "reserved" at initialization. This patch makes hibernation work
again.
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Fixes: 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.") Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: David Daney <david.daney@cavium.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12722/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12721/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f51246efee2b ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.
Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().
Fixes: f51246efee2b ("MIPS: Get rid of finish_arch_switch().") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12726/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com> Fixes: 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Petr Malat <oss@malat.biz> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 85efde6f4e0d ("make exported headers use strict posix types")
changed the asm-generic siginfo.h to use the __kernel_* types, and
commit 3a471cbc081b ("remove __KERNEL_STRICT_NAMES") make the internal
types accessible only to the kernel, but the MIPS implementation hasn't
been updated to match.
Switch to proper types now so that the exported asm/siginfo.h won't
produce quite so many compiler errors when included alone by a user
program.
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a build regression from commit c9017757c532 ("MIPS: init upper 64b
of vector registers when MSA is first used"):
arch/mips/built-in.o: In function `enable_restore_fp_context':
traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are
unable to figure out that calls to `_init_msa_upper' are indeed dead.
Of the many ways to tackle this failure choose the approach we have
already taken in `thread_msa_context_live'.
[ralf@linux-mips.org: Drop patch segment to junk file.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13271/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.
Fixes: 102cedc32a6e ("MIPS: microMIPS: Floating point support.") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-6 started warning by default about variables that are not
used anywhere and that are marked 'const', generating many
false positives in an allmodconfig build, e.g.:
arch/arm/mach-davinci/board-da830-evm.c:282:20: warning: 'da830_evm_emif25_pins' defined but not used [-Wunused-const-variable=]
arch/arm/plat-omap/dmtimer.c:958:34: warning: 'omap_timer_match' defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:625:39: warning: 'acpi_bcm_default_gpios' defined but not used [-Wunused-const-variable=]
drivers/char/hw_random/omap-rng.c:92:18: warning: 'reg_map_omap4' defined but not used [-Wunused-const-variable=]
drivers/devfreq/exynos/exynos5_bus.c:381:32: warning: 'exynos5_busfreq_int_pm' defined but not used [-Wunused-const-variable=]
drivers/dma/mv_xor.c:1139:34: warning: 'mv_xor_dt_ids' defined but not used [-Wunused-const-variable=]
This is similar to the existing -Wunused-but-set-variable warning
that was added in an earlier release and that we disable by default
now and only enable when W=1 is set, so it makes sense to do
the same here. Once we have eliminated the majority of the
warnings for both, we can put them back into the default list.
We probably want this in backport kernels as well, to allow building
them with gcc-6 without introducing extra warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit 90a88d6ef88e ("scsi: fix soft lockup in scsi_remove_target() on module
removal").
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795d3 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and 40998193560d ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38 Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Commit ce657611baf9 ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611baf9 ("hpfs: kstrdup() out of memory handling") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ezequiel reported that he's facing UBI going into read-only
mode after power cut. It turned out that this behavior happens
only when updating a static volume is interrupted and Fastmap is
used.
UBI checks static volumes for data consistency and reads the
whole volume upon first open. If the volume is found erroneous
users of UBI cannot read from it, but another volume update is
possible to fix it. The check is performed by running
ubi_eba_read_leb() on every allocated LEB of the volume.
For static volumes ubi_eba_read_leb() computes the checksum of all
data stored in a LEB. To verify the computed checksum it has to read
the LEB's volume header which stores the original checksum.
If the volume header is not found UBI treats this as fatal internal
error and switches to RO mode. If the UBI device was attached via a
full scan the assumption is correct, the volume header has to be
present as it had to be there while scanning to get known as mapped.
If the attach operation happened via Fastmap the assumption is no
longer correct. When attaching via Fastmap UBI learns the mapping
table from Fastmap's snapshot of the system state and not via a full
scan. It can happen that a LEB got unmapped after a Fastmap was
written to the flash. Then UBI can learn the LEB still as mapped and
accessing it returns only 0xFF bytes. As UBI is not a FTL it is
allowed to have mappings to empty PEBs, it assumes that the layer
above takes care of LEB accounting and referencing.
UBIFS does so using the LEB property tree (LPT).
For static volumes UBI blindly assumes that all LEBs are present and
therefore special actions have to be taken.
The described situation can happen when updating a static volume is
interrupted, either by a user or a power cut.
The volume update code first unmaps all LEBs of a volume and then
writes LEB by LEB. If the sequence of operations is interrupted UBI
detects this either by the absence of LEBs, no volume header present
at scan time, or corrupted payload, detected via checksum.
In the Fastmap case the former method won't trigger as no scan
happened and UBI automatically thinks all LEBs are present.
Only by reading data from a LEB it detects that the volume header is
missing and incorrectly treats this as fatal error.
To deal with the situation ubi_eba_read_leb() from now on checks
whether we attached via Fastmap and handles the absence of a
volume header like a data corruption error.
This way interrupted static volume updates will correctly get detected
also when Fastmap is used.
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.
The bar number is found in reg2 within the gdd. Therefore
we need to change the assigment from reg1 to reg2 which
is the correct location.
Signed-off-by: Andreas Werner <andreas.werner@men.de> Fixes: '3764e82e5' drivers: Introduce MEN Chameleon Bus Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
51d7d5205d33 ("powerpc: Add smp_mb() to arch_spin_is_locked()") d86b8da04dfa ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")
qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.
And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:
spin_lock(A) spin_lock(B)
spin_unlock_wait(B) if (!spin_is_locked(A))
do_something() do_something()
In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).
To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO") Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com> Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO") Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch> Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula") Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
Commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b4ff8389ed14 is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.
This ensures that the guest doesn't see XSAVE extensions
(e.g. xgetbv1 or xsavec) that the host lacks.
Cc: stable@vger.kernel.org Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
[4.5 does have CPUID_D_1_EAX, but earlier kernels don't, so use
the numeric value. This is consistent with other occurrences
of cpuid_mask in arch/x86/kvm/cpuid.c - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.
We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.
There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.
This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.
With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.
Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).
Commit d28bc9dd25ce reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.
The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.
Fixes: d28bc9dd25ce ("KVM: x86: INIT and reset sequences are different") Signed-off-by: Bruce Rogers <brogers@suse.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSR 0x2f8 accessed the 124th Variable Range MTRR ever since MTRR support
was introduced by 9ba075a664df ("KVM: MTRR support").
0x2f8 became harmful when 910a6aae4e2e ("KVM: MTRR: exactly define the
size of variable MTRRs") shrinked the array of VR MTRRs from 256 to 8,
which made access to index 124 out of bounds. The surrounding code only
WARNs in this situation, thus the guest gained a limited read/write
access to struct kvm_arch_vcpu.
0x2f8 is not a valid VR MTRR MSR, because KVM has/advertises only 16 VR
MTRR MSRs, 0x200-0x20f. Every VR MTRR is set up using two MSRs, 0x2f8
was treated as a PHYSBASE and 0x2f9 would be its PHYSMASK, but 0x2f9 was
not implemented in KVM, therefore 0x2f8 could never do anything useful
and getting rid of it is safe.
This fixes CVE-2016-3713.
Fixes: 910a6aae4e2e ("KVM: MTRR: exactly define the size of variable MTRRs") Reported-by: David Matlack <dmatlack@google.com> Signed-off-by: Andy Honig <ahonig@google.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.
Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters
It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.
Fixes: 99dfc3357e98 ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation") Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Matthew Giassa <matthew@giassa.net> CC: Mathias Nyman <mathias.nyman@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 8b5249019352 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing") Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b8639 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8d3 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b8639 ("gadget/function/f_fs.c: use put iov_iter into io_data") Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[johan: rebase and replace commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
[properly sort them - gregkh] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
When a message is received and amthif client is not in reading state
the message is ignored and left dangling in the queue. This may happen
after one of the amthif host connections is closed w/o completing the
reading. Another client will pick up a wrong message on next read
attempt which will lead to link reset.
To prevent this the driver has to properly discard the message when
amthif client is not in reading state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write. Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.
This patch introduces a mutex to protect against the concurrent device
creations.
The write handler allocates skbs and queues them into data->readq.
Read side should read them, if there is any. If there is none, skbs
should be dropped by hdev->flush. But this happens only if the device
is HCI_UP, i.e. hdev->power_on work was triggered already. When it was
not, skbs stay allocated in the queue when /dev/vhci is closed. So
purge the queue in ->release.
Program to reproduce:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
Both vhci_get_user and vhci_release race with open_timeout work. They
both contain cancel_delayed_work_sync, but do not test whether the
work actually created hdev or not. Since the work can be in progress
and _sync will wait for finishing it, we can have data->hdev allocated
when cancel_delayed_work_sync returns. But the call sites do 'if
(data->hdev)' *before* cancel_delayed_work_sync.
As a result:
* vhci_get_user allocates a second hdev and puts it into
data->hdev. The former is leaked.
* vhci_release does not release data->hdev properly as it thinks there
is none.
Fix both cases by moving the actual test *after* the call to
cancel_delayed_work_sync.
This can be hit by this program:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <sys/stat.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
int fd;
srand(time(NULL));
while (1) {
const int delta = (rand() % 200 - 100) * 100;
fd = open("/dev/vhci", O_RDWR);
if (fd < 0)
err(1, "open");
And the result is:
BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228
Read of size 8 by task kworker/u13:1/32068
=============================================================================
BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040
...
kmem_cache_alloc_trace+0x150/0x190
vhci_open+0x50/0x330 [hci_vhci]
misc_open+0x35b/0x4e0
chrdev_open+0x23b/0x510
...
INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040
...
__slab_free+0x204/0x310
vhci_release+0xa4/0xd0 [hci_vhci]
...
INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080
INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600
Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............
Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k....
Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k....
Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................
Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k....
Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n.............
Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b......
Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k....
Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. .............
Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=....
Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . ..............
Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........
Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........
CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
Workqueue: hci0 hci_cmd_work [bluetooth] 00000000ffffffffffffffff81926cfaffff88006be37c68ffff88006bc27180 ffff88006b0c1200ffff88006b0c1234ffffffff81577993ffffffff82489320 ffff88006bc242400000000000000046ffff88006a100000000000026e51eb80
Call Trace:
...
[<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150
[<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci]
[<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth]
[<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth]
[<ffffffff811a1375>] ? process_one_work+0x815/0x1340
[<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0
[<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340
[<ffffffff811b3c68>] ? kthread+0x1c8/0x230
...
Memory state around the buggy address: ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.
The order of the _OSI related functionalities is as follows:
acpi_blacklisted()
acpi_dmi_osi_linux()
acpi_osi_setup()
acpi_osi_setup()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
parse_args()
__setup("acpi_osi=")
acpi_osi_setup_linux()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
acpi_early_init()
acpi_initialize_subsystem()
acpi_ut_initialize_interfaces()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
acpi_bus_init()
acpi_os_initialize1()
acpi_install_interface_handler(acpi_osi_handler)
acpi_osi_setup_late()
acpi_update_interfaces() for "!"
>>>>>>>>>>>>>>>>>>>>>>>>
acpi_osi_handler()
Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command
line setting can override the DMI detection. That's why acpi_blacklisted()
is put before __setup("acpi_osi=").
Then we can notice the following wrong invocation order. There are
acpi_update_interfaces() (marked by <<<<) calls invoked before
acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible
to use acpi_osi=!* correctly from OSI DMI table or from the command line.
The use of acpi_osi=!* is meant to disable both ACPICA
(acpi_gbl_supported_interfaces) and Linux specific strings
(osi_setup_entries) while the ACPICA part should have stopped working
because of the order issue.
This patch fixes this issue by moving acpi_update_interfaces() to where
it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be
invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux
specific strings are still handled in the original place in order to make
the following command line working: acpi_osi=!* acpi_osi="Module Device".
Note that since acpi_osi=!* is meant to further disable linux specific
string comparing to the acpi_osi=!, there is no such use case in our bug
fixing work and hence there is no one using acpi_osi=!* either from the
command line or from the DMI quirks, this issue is just a theoretical
issue.
Fixes: 741d81280ad2 (ACPI: Add facility to remove all _OSI strings) Tested-by: Lukas Wunner <lukas@wunner.de> Tested-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some eMMCs set the partition switch timeout too low.
Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable. Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.
Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.
The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbebe) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GICv3 driver wrongly assumes that it runs on the non-secure
side of a secure-enabled system, while it could be on a system
with a single security state, or a GICv3 with GICD_CTLR.DS set.
Either way, it is important to configure this properly, or
interrupts will simply not be delivered on this HW.
Reported-by: Peter Maydell <peter.maydell@linaro.org> Tested-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an IPI is generated by a CPU, the pattern looks roughly like:
<write shared data>
smp_wmb();
<write to GIC to signal SGI>
On the receiving CPU we rely on the fact that, once we've taken the
interrupt, then the freshly written shared data must be visible to us.
Put another way, the CPU isn't going to speculate taking an interrupt.
Unfortunately, this assumption turns out to be broken.
Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy
to read some shared_data. Before CPUx has done anything, a random
peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised.
CPUy then takes the IRQ and starts executing the entry code, heading
towards gic_handle_irq. Furthermore, let's assume that a bunch of the
previous interrupts handled by CPUy were SGIs, so the branch predictor
kicks in and speculates that irqnr will be <16 and we're likely to
head into handle_IPI. The prefetcher then grabs a speculative copy of
shared_data which contains a stale value.
Meanwhile, CPUx gets round to updating shared_data and asking the GIC
to send an SGI to CPUy. Internally, the GIC decides that the SGI is
more important than the peripheral interrupt (which hasn't yet been
ACKed) but doesn't need to do anything to CPUy, because the IRQ line
is already raised.
CPUy then reads the ACK register on the GIC, sees the SGI value which
confirms the branch prediction and we end up with a stale shared_data
value.
This patch fixes the problem by adding an smp_rmb() to the IPI entry
code in gic_handle_irq. As it turns out, the combination of a control
dependency and an ISB instruction from the EOI in the GICv3 driver is
enough to provide the ordering we need, so we add a comment there
justifying the absence of an explicit smp_rmb().
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems show a minimal load average of 0.00, 0.01, 0.05 even when they
have no load at all.
Uptime and /proc/loadavg on all systems with kernels released during the
last five years up until kernel version 4.6-rc5, show a 5- and 15-minute
minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on
idle systems, but the way the kernel calculates this value prevents it
from getting lower than the mentioned values.
Likewise but not as obviously noticeable, a fully loaded system with no
processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95
(multiplied by number of cores).
Once the (old) load becomes 93 or higher, it mathematically can never
get lower than 93, even when the active (load) remains 0 forever.
This results in the strange 0.00, 0.01, 0.05 uptime values on idle
systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05.
It is not correct to add a 0.5 rounding (=1024/2048) here, since the
result from this function is fed back into the next iteration again,
so the result of that +0.5 rounding value then gets multiplied by
(2048-2037), and then rounded again, so there is a virtual "ghost"
load created, next to the old and active load terms.
By changing the way the internally kept value is rounded, that internal
value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon
increasing load, the internally kept load value is rounded up, when the
load is decreasing, the load value is rounded down.
The modified code was tested on nohz=off and nohz kernels. It was tested
on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was
tested on single, dual, and octal cores system. It was tested on virtual
hosts and bare hardware. No unwanted effects have been observed, and the
problems that the patch intended to fix were indeed gone.
Tested-by: Damien Wyart <damien.wyart@free.fr> Signed-off-by: Vik Heyndrickx <vik.heyndrickx@veribox.net> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Doug Smythies <dsmythies@telus.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 0f004f5a696a ("sched: Cure more NO_HZ load average woes") Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org> Fixes: 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.
caam_jr_alloc() used to return NULL if a JR device could not be
allocated for a session. In turn, every user of this function used
IS_ERR() function to verify if anything went wrong, which does NOT look
for NULL values. This made the kernel crash if the sanity check failed,
because the driver continued to think it had allocated a valid JR dev
instance to the session and at some point it tries to do a caam_jr_free()
on a NULL JR dev pointer.
This patch is a fix for this issue.
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thus it overflows and the resulting number is less than 4080, which makes
3823 / 4080 = 0
an nr_pages is set to this. As we already checked against the minimum that
nr_pages may be, this causes the logic to fail as well, and we crash the
kernel.
There's no reason to have the two DIV_ROUND_UP() (that's just result of
historical code changes), clean up the code and fix this bug.
Fixes: 83f40318dab00 ("ring-buffer: Make removal of ring buffer pages atomic") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size variable to change the ring buffer in ftrace is a long. The
nr_pages used to update the ring buffer based on the size is int. On 64 bit
machines this can cause an overflow problem.
For example, the following will cause the ring buffer to crash:
WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260
Which is:
RB_WARN_ON(cpu_buffer, nr_removed);
Note each ring buffer page holds 4080 bytes.
This is because:
1) 10 causes the ring buffer to have 3 pages.
(10kb requires 3 * 4080 pages to hold)
2) (2^31 / 2^10 + 1) * 4080 = 8556384240
The value written into buffer_size_kb is shifted by 10 and then passed
to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760
3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE
which is 4080. 8761737461760 / 4080 = 2147484672
4) nr_pages is subtracted from the current nr_pages (3) and we get: 2147484669. This value is saved in a signed integer nr_pages_to_update
5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int
turns into the value of -2147482627
6) As the value is a negative number, in update_pages_handler() it is
negated and passed to rb_remove_pages() and 2147482627 pages will
be removed, which is much larger than 3 and it causes the warning
because not all the pages asked to be removed were removed.
In testing with HiKey, we found that since
commit 3f30b158eba5 ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com> Cc: "David B. Robins" <linux@davidrobins.net> Cc: Mark Craske <Mark_Craske@mentor.com> Cc: Emil Goode <emilgoode@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: YongQin Liu <yongqin.liu@linaro.org> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Ivan Vecera <ivecera@redhat.com> Cc: linux-usb@vger.kernel.org Cc: netdev@vger.kernel.org Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client:
...
Set NullSession to FALSE
If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND
AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND
(AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1)
OR
AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0))
-- Special case: client requested anonymous authentication
Set NullSession to TRUE
...
Only server which map unknown users to guest will allow
access using a non-null NTChallengeResponse.
For Samba it's the "map to guest = bad user" option.
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrong return code was being returned on SMB3 rmdir of
non-empty directory.
For SMB3 (unlike for cifs), we attempt to delete a directory by
set of delete on close flag on the open. Windows clients set
this flag via a set info (SET_FILE_DISPOSITION to set this flag)
which properly checks if the directory is empty.
With this patch on smb3 mounts we correctly return
"DIRECTORY NOT EMPTY"
on attempts to remove a non-empty directory.
Signed-off-by: Steve French <steve.french@primarydata.com> Acked-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EC field of the constructed ESR is conditionally modified by ORing in
ESR_ELx_EC_DABT_LOW for a data abort. However, ESR_ELx_EC_SHIFT is missing
from this condition.
Signed-off-by: Matt Evans <matt.evans@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log