Ben Hutchings [Wed, 11 May 2011 16:41:18 +0000 (17:41 +0100)]
sfc: Always map MCDI shared memory as uncacheable
We enabled write-combining for memory-mapped registers in commit 65f0b417dee94f779ce9b77102b7d73c93723b39, but inhibited it for the
MCDI shared memory where this is not supported. However,
write-combining mappings also allow read-reordering, which may also
be a problem.
I found that when an SFC9000-family controller is connected to an
Intel 3000 chipset, and write-combining is enabled, the controller
stops responding to PCIe read requests during driver initialisation
while the driver is polling for completion of an MCDI command. This
results in an NMI and system hang. Adding read memory barriers
between all reads to the shared memory area appears to reduce but not
eliminate the probability of this.
We have not yet established whether this is a bug in our BIU or in the
PCIe bridge. For now, work around by mapping the shared memory area
separately.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Revert: veth: remove unneeded ifname code from veth_newlink()
84c49d8c3e4abefb0a41a77b25aa37ebe8d6b743 ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com> Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Sat, 30 Apr 2011 08:29:27 +0000 (08:29 +0000)]
smsc95xx: fix reset check
The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Fix failure to enable WoL by default when possible
tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter. Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: Only allow recv on connected seqpacket sockets.
This fixes the following oops discovered by Dan Aloni:
> Anyway, the following is the output of the Oops that I got on the
> Ubuntu kernel on which I first detected the problem
> (2.6.37-12-generic). The Oops that followed will be more useful, I
> guess.
The bug was that unix domain sockets use a pseduo packet for
connecting and accept uses that psudo packet to get the socket.
In the buggy seqpacket case we were allowing unconnected
sockets to call recvmsg and try to receive the pseudo packet.
That is always wrong and as of commit 7361c36c5 the pseudo
packet had become enough different from a normal packet
that the kernel started oopsing.
Do for seqpacket_recv what was done for seqpacket_send in 2.5
and only allow it on connected seqpacket sockets.
Cc: stable@kernel.org Tested-by: Dan Aloni <dan@aloni.org> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of pause frames advertise in mii_get_an. This provides all drivers
that use mii_ethtool_gset to represent their own and Link partner flow control
abilities in ethtool.
Signed-off-by: Artem Polyakov <artpol84@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adam Jaremko [Thu, 28 Apr 2011 07:41:18 +0000 (07:41 +0000)]
net: ftmac100: fix scheduling while atomic during PHY link status change
Signed-off-by: Adam Jaremko <adam.jaremko@gmail.com> Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It occured during some stress testing, in which the reporter was repeatedly
removing and modprobing the bnx2 module while doing various other random
operations on the bnx2 registered net device. Noting that this error occured on
a serdes based device, we noted that there were a few ethtool operations (most
notably self_test and set_phys_id) that have execution paths that lead into
bnx2_setup_serdes_phy. This function is notable because it executes a mod_timer
call, which starts the bp->timer running. Currently bnx2 is setup to assume
that this timer only nees to be stopped when bnx2_close or bnx2_suspend is
called. Since the above ethtool operations are not gated on the net device
having been opened however, that assumption is incorrect, and can lead to the
timer still running after the module has been removed, leading to the oops above
(as well as other simmilar oopses).
Fix the problem by ensuring that the timer is stopped when pci_device_unregister
is called.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Hushan Jia <hjia@redhat.com> CC: Michael Chan <mchan@broadcom.com> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.
Cc: stable@kernel.org # 2.6.35+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Peter Korsgaard [Tue, 26 Apr 2011 01:45:41 +0000 (01:45 +0000)]
dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
The 88e6085 has a few differences from the other devices in the port
control registers, causing unknown multicast/broadcast packets to get
dropped when using the standard port setup.
At the same time update kconfig to clarify that the mv88e6085 is now
supported.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Stewart [Thu, 28 Apr 2011 05:43:37 +0000 (05:43 +0000)]
usbnet: Resubmit interrupt URB if device is open
Resubmit interrupt URB if device is open. Use a flag set in
usbnet_open() to determine this state. Also kill and free
interrupt URB in usbnet_disconnect().
[Rebased off git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git]
Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: at drivers/net/wireless/iwlegacy/iwl-4965.c:1128 \
iwl4965_send_tx_power+0x61/0x102 [iwl4965]() Hardware name: [...]
TX Power requested while scanning!
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
xfrm: Check for the new replay implementation if an esn state is inserted
IPsec extended sequence numbers can be used only with the new
anti-replay window implementation. So check if the new implementation
is used if an esn state is inserted and return an error if it is not.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
When we use IPsec extended sequence numbers, we may overwrite
the last scatterlist of the associated data by the scatterlist
for the skb. This patch fixes this by placing the scatterlist
for the skb right behind the last scatterlist of the associated
data. esp4 does it already like that.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Fix replay window size calculation on initialization
On replay initialization, we compute the size of the replay
buffer to see if the replay window fits into the buffer.
This computation lacks a mutliplication by 8 because we need
the size in bit, not in byte. So we might return an error
even though the replay window would fit into the buffer.
This patch fixes this issue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The oops happens in dst_metrics_write_ptr()
include/net/dst.h:124: return dst->ops->cow_metrics(dst, p);
dst->ops->cow_metrics is NULL and causes the oops.
Provide cow_metrics() methods, like we did in commit 214f45c91bb
(net: provide default_advmss() methods to blackhole dst_ops)
Signed-off-by: Held Bernhard <berny156@gmx.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The default maximum transmit length for NCM USB frames should be so
that a short packet happens at the end if the device supports a length
greater than the defined maximum. This is achieved by adding 4 bytes
to the maximum length so that the existing logic can fit a short
packet there.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
François Romieu [Sun, 24 Apr 2011 15:38:48 +0000 (17:38 +0200)]
r8169: don't request firmware when there's no userspace.
The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Fixed-by: Ciprian Docan <docan@eden.rutgers.edu> Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Fixed packets parameters for FW in UDP checksum offload flow.
Do not dereference TCP headers on non TCP frames. Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 22 Apr 2011 08:10:59 +0000 (08:10 +0000)]
netconsole: fix deadlock when removing net driver that netconsole is using (v2)
A deadlock was reported to me recently that occured when netconsole was being
used in a virtual guest. If the virtio_net driver was removed while netconsole
was setup to use an interface that was driven by that driver, the guest
deadlocked. No backtrace was provided because netconsole was the only console
configured, but it became clear pretty quickly what the problem was. In
netconsole_netdev_event, if we get an unregister event, we call
__netpoll_cleanup with the target_list_lock held and irqs disabled.
__netpoll_cleanup can, if pending netpoll packets are waiting call
cancel_delayed_work_sync, which is a sleeping path. the might_sleep call in
that path gets triggered, causing a console warning to be issued. The
netconsole write handler of course tries to take the target_list_lock again,
which we already hold, causing deadlock.
The fix is pretty striaghtforward. Simply drop the target_list_lock and
re-enable irqs prior to calling __netpoll_cleanup, the re-acquire the lock, and
restart the loop. Confirmed by myself to fix the problem reported.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit was meant to support transport bridging, and specifically
virtual machines bridged to an ethernet interface connected to a
switch port wiht 802.1x enabled.
But this isn't the way to do it, it breaks too many other things.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Gardner [Wed, 20 Apr 2011 09:00:49 +0000 (09:00 +0000)]
atl1c: Fix work event interrupt/task races
The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.
Cc: stable@kernel.org Cc: Jie Yang <jie.yang@atheros.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 21 Apr 2011 00:20:04 +0000 (00:20 +0000)]
be2net: increment work_counter in be_worker
The commit 609ff3b ("be2net: add code to display temperature of ASIC")
adds support to display temperature of ASIC but there is missing
increment of work_counter in be_worker. Because of this 1) the
function be_cmd_get_die_temperature is called every 1 second instead
of every 32 seconds 2) be_cmd_get_die_temperature is called, although
it is not supported. This patch fixes this bug.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Egerer [Wed, 20 Apr 2011 22:56:02 +0000 (22:56 +0000)]
ipv6: Remove hoplimit initialization to -1
The changes introduced with git-commit a02e4b7d ("ipv6: Demark default
hoplimit as zero.") missed to remove the hoplimit initialization. As a
result, ipv6_get_mtu interprets the return value of dst_metric_raw
(-1) as 255 and answers ping6 with this hoplimit. This patche removes
the line such that ping6 is answered with the hoplimit value
configured via sysctl.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Galbusera [Thu, 21 Apr 2011 02:21:21 +0000 (02:21 +0000)]
powerpc: Fix multicast problem in fs_enet driver
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
At this point, skb->data points to skb_transport_header.
So, headroom check is wrong.
For some case:bridge(UFO is on) + eth device(UFO is off),
there is no enough headroom for IPv6 frag head.
But headroom check is always false.
This will bring about data be moved to there prior to skb->head,
when adding IPv6 frag header to skb.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link, making bisection of other problems impossible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 19 Apr 2011 18:44:04 +0000 (20:44 +0200)]
mac80211: fix SMPS debugfs locking
The locking with SMPS requests means that the
debugs file should lock the mgd mutex, not the
iflist mutex. Calls to __ieee80211_request_smps()
need to hold that mutex, so add an assertion.
This has always been wrong, but for some reason
never been noticed, probably because the locking
error only happens while unassociated.
Cc: stable@kernel.org [2.6.34+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The slave member of struct aggregator does not necessarily point
to a slave which is part of the aggregator. It points to the
slave structure containing the aggregator structure, while
completely different slaves (or no slaves at all) may be part of
the aggregator.
The agg_device_up() function wrongly uses agg->slave to find the state
of the aggregator. Use agg->lag_ports->slave instead. The bug has
been introduced by commit 4cd6fe1c6483cde93e2ec91f58b7af9c9eea51ad
("bonding: fix link down handling in 802.3ad mode").
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Thu, 14 Apr 2011 22:41:43 +0000 (00:41 +0200)]
ath9k: fix the return value of ath_stoprecv
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Paul Stewart <pstew@google.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
netfilter: ipset: Fix the order of listing of sets
A restoreable saving of sets requires that list:set type of sets
come last and the code part which should have taken into account
the ordering was broken. The patch fixes the listing order.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net>
shutdown should wait for SCO link to be properly disconnected before
detroying the socket, otherwise an application using the socket may
assume link is properly disconnected before it really happens which
can be a problem when e.g synchronizing profile switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In the teardown path the reset command is sent to the controller,
this event causes the command timer to be reactivated.
So the timer is removed in two situations, when the adapter isn't
marked as UP and when we know that some command has been sent.
Reported-by: Keith Packard <keithp@keithp.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ville Tervo [Thu, 7 Apr 2011 11:59:50 +0000 (14:59 +0300)]
Bluetooth: Fix refcount balance for hci connection
hci_io_capa_reply_evt() holds reference for hciconnection. It's useless since
hci_io_capa_request_evt()/hci_simple_pair_complete_evt() already protects the
connection. In addition it leaves connection open after failed SSP pairing.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Daniel Halperin [Wed, 6 Apr 2011 19:47:25 +0000 (12:47 -0700)]
iwlwifi: fix frame injection for HT channels
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ip6_pol_route panic: Do not allow VLAN on loopback
Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.
Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.
The result of this patch is:
# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:- error: Operation not supported
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Apr 2011 05:55:37 +0000 (05:55 +0000)]
ip: ip_options_compile() resilient to NULL skb route
Scot Doyle demonstrated ip_options_compile() could be called with an skb
without an attached route, using a setup involving a bridge, netfilter,
and forged IP packets.
Let's make ip_options_compile() and ip_options_rcv_srr() a bit more
robust, instead of changing bridge/netfilter code.
With help from Hiroaki SHIMODA.
Reported-by: Scot Doyle <lkml@scotdoyle.com> Tested-by: Scot Doyle <lkml@scotdoyle.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com> Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
huajun li [Wed, 13 Apr 2011 15:43:32 +0000 (15:43 +0000)]
usbnet: Fix up 'FLAG_POINTTOPOINT' and 'FLAG_MULTI_PACKET' overlaps.
USB tethering does not work anymore since 2.6.39-rc2, but it's okay in
-rc1. The root cause is the new added mask code 'FLAG_POINTTOPOINT'
overlaps 'FLAG_MULTI_PACKET' in include/linux/usb/usbnet.h, this
causes logic issue in rx_process(). This patch cleans up the overlap.
Reported-and-Tested-by: Gottfried Haider <gottfried.haider@gmail.com> Signed-off-by: Huajun Li <huajun.li.lee@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It causes known regressions for programs that expect to be able to use
SO_REUSEADDR to shutdown a socket, then successfully rebind another
socket to the same ID.
Programs such as haproxy and amavisd expect this to work.
This should fix kernel bugzilla 32832.
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Grant Likely <grant.likely@secretlab.ca> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The SET target with --del-set did not work due to using wrongly
the internal dimension of --add-set instead of --del-set.
Also, the checkentries did not release the set references when
returned an error. Bugs reported by Lennert Buytenhek.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net>
netfilter: ipset: bitmap:ip,mac type requires "src" for MAC
Enforce that the second "src/dst" parameter of the set match and SET target
must be "src", because we have access to the source MAC only in the packet.
The previous behaviour, that the type required the second parameter
but actually ignored the value was counter-intuitive and confusing.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net>
sctp: fix oops while removed transport still using as retran path
Since we can not update retran path to unconfirmed transports,
when we remove a peer, the retran path may not be update if the
other transports are all unconfirmed, and we will still using
the removed transport as the retran path. This may cause panic
if retrasnmit happen.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Solved the problem, but forgot to change the DEBUG statement.
Thus it was still possible to dereference a NULL pointer.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 12 Apr 2011 14:38:37 +0000 (14:38 +0000)]
net: Disable all TSO features when SG is disabled
The feature flags NETIF_F_TSO and NETIF_F_TSO6 independently enable
TSO for IPv4 and IPv6 respectively. However, the test in
netdev_fix_features() and its predecessor functions was never updated
to check for NETIF_F_TSO6, possibly because it was originally proposed
that TSO for IPv6 would be dependent on both feature flags.
Now that these feature flags can be changed independently from
user-space and we depend on netdev_fix_features() to fix invalid
feature combinations, it's important to disable them both if
scatter-gather is disabled. Also disable NETIF_F_TSO_ECN so
user-space sees all TSO features as disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Turton [Mon, 11 Apr 2011 10:42:43 +0000 (11:42 +0100)]
sfc: Use rmb() to ensure reads occur in order
Enabling write-combining may also enable read reordering. The BIU is
only guaranteed to read from a 128-bit CSR or 64-bit SRAM word when
the host reads from its lowest address; otherwise the BIU may use the
latched value. Therefore we need to reinstate the read memory
barriers after the first read operation for each CSR or SRAM word.
Signed-off-by; Ben Hutchings <bhutchings@solarflare.com>
David S. Miller [Tue, 12 Apr 2011 22:33:23 +0000 (15:33 -0700)]
ieee802154: Remove hacked CFLAGS in net/ieee802154/Makefile
It adds -Wall (which the kernel carefully controls already) and of all
things -DDEBUG (which should be set by other means if desired, please
we have dynamic-debug these days).
Kill this noise.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Tue, 12 Apr 2011 22:29:54 +0000 (15:29 -0700)]
irda: fix locking unbalance in irda_sendmsg
5b40964eadea40509d353318d2c82e8b7bf5e8a5 ("irda: Remove BKL instances
from af_irda.c") introduced a path where we have a locking unbalance.
If we pass invalid flags, we unlock a socket we never locked,
resulting in this...
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
trinity/20101 is trying to release lock (sk_lock-AF_IRDA) at:
[<ffffffffa057f001>] irda_sendmsg+0x207/0x21d [irda]
but there are no more locks to release!
other info that might help us debug this:
no locks held by trinity/20101.
Patrick McHardy [Tue, 12 Apr 2011 05:39:51 +0000 (05:39 +0000)]
connector: fix skb double free in cn_rx_skb()
When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: Eric B Munson <emunson@mgebm.net> Signed-off-by: Patrick McHardy <kaber@trash.net> Tested-by: Eric B Munson <emunson@mgebm.net> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Do not wrap sysctl igmp_max_memberships in IP_MULTICAST
controlling igmp_max_membership is useful even when IP_MULTICAST
is off.
Quagga(an OSPF deamon) uses multicast addresses for all interfaces
using a single socket and hits igmp_max_membership limit when
there are 20 interfaces or more.
Always export sysctl igmp_max_memberships in proc, just like
igmp_max_msf
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Scot Doyle <lkml@scotdoyle.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Reviewed-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com> Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Tested-by: Richard Farina <sidhayn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 8 Apr 2011 18:13:18 +0000 (20:13 +0200)]
ath9k_hw: fix stopping rx DMA during resets
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet [Tue, 12 Apr 2011 20:39:14 +0000 (13:39 -0700)]
bridge: reset IPCB in br_parse_ip_options
Commit 462fb2af9788a82 (bridge : Sanitize skb before it enters the IP
stack), missed one IPCB init before calling ip_options_compile()
Thanks to Scot Doyle for his tests and bug reports.
Reported-by: Scot Doyle <lkml@scotdoyle.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Acked-by: Bandan Das <bandan.das@stratus.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Cc: Jan Lübbe <jluebbe@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 4 Apr 2011 13:22:11 +0000 (14:22 +0100)]
sfc: Do not use efx_process_channel_now() in online self-test
During self-tests we use efx_process_channel_now() to handle
completion and other events synchronously. This disables interrupts
and NAPI processing for the channel in question, but it may still be
interrupted by another channel. A single socket may receive packets
from multiple net devices or even multiple channels of the same net
device, so this can result in deadlock on a socket lock.
Receiving packets in process context will also result in incorrect
classification by the network cgroup classifier.
Therefore, we must only use efx_process_channel_now() in the offline
loopback tests (which never deliver packets up the stack) and not for
the online interrupt and event tests.
For the interrupt test, there is no reason to process events. We
only care that an interrupt is raised.
For the event test, we want to know whether events have been received,
and there may be many events ahead of the one we inject. Therefore
remove efx_channel::magic_count and instead test whether
efx_channel::eventq_read_ptr advances. This is currently an event
queue index and might wrap around to exactly the same value, resulting
in a false negative. Therefore move the masking to efx_event() and
efx_nic_eventq_read_ack() so that it cannot wrap within the time of
the test.
The event test also tries to diagnose failures by checking whether an
event was delivered without causing an interrupt. Add and use a
helper function that only does this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Neil Turton [Mon, 4 Apr 2011 12:46:23 +0000 (13:46 +0100)]
sfc: Stop the TX queues during loopback self-tests
If the TX queues are running during loopback self tests, host
traffic gets looped back which causes the test to fail. Avoid
restarting the TX queues after the port reset so that any packets
sent by the host get held back until after the tests have completed.
[bwh: Also wake all TX queues at the end of self-tests.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
caif: performance bugfix - allow radio stack to prioritize packets.
In the CAIF Payload message the Packet Type indication must be set to
UNCLASSIFIED in order to allow packet prioritization in the modem's
network stack. Otherwise TCP-Ack is not prioritized in the modems
transmit queue.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amit salecha [Mon, 11 Apr 2011 02:10:22 +0000 (02:10 +0000)]
netxen: limit skb frags for non tso packet
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Pan(潘卫平) [Fri, 8 Apr 2011 03:40:19 +0000 (03:40 +0000)]
bonding:set save_load to 0 when initializing
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log