Edward Cree [Wed, 27 May 2015 12:13:54 +0000 (13:13 +0100)]
sfc: add tracing of MCDI commands
MCDI tracing is conditional on CONFIG_SFC_MCDI_LOGGING, which is enabled
by default.
Each MCDI command will produce a console line like
sfc dom:bus:dev:fn ifname: MCDI RPC REQ: xxxxxxxx [yyyyyyyy...]
where xxxxxxxx etc. are the raw MCDI payload in 32-bit hex chunks.
The response will then produce a similar line with "RESP" instead of "REQ",
and containing the MCDI response payload (if any).
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sorin Dumitru [Tue, 26 May 2015 07:42:04 +0000 (10:42 +0300)]
vxlan: release lock after each bucket in vxlan_cleanup
We're seeing some softlockups from this function when there
are a lot fdb entries on a vxlan device. Taking the lock for
each bucket instead of the whole table is enough to fix that.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 24 May 2015 21:49:35 +0000 (14:49 -0700)]
tcp/dccp: try to not exhaust ip_local_port_range in connect()
A long standing problem on busy servers is the tiny available TCP port
range (/proc/sys/net/ipv4/ip_local_port_range) and the default
sequential allocation of source ports in connect() system call.
If a host is having a lot of active TCP sessions, chances are
very high that all ports are in use by at least one flow,
and subsequent bind(0) attempts fail, or have to scan a big portion of
space to find a slot.
In this patch, I changed the starting point in __inet_hash_connect()
so that we try to favor even [1] ports, leaving odd ports for bind()
users.
We still perform a sequential search, so there is no guarantee, but
if connect() targets are very different, end result is we leave
more ports available to bind(), and we spread them all over the range,
lowering time for both connect() and bind() to find a slot.
This strategy only works well if /proc/sys/net/ipv4/ip_local_port_range
is even, ie if start/end values have different parity.
Therefore, default /proc/sys/net/ipv4/ip_local_port_range was changed to
32768 - 60999 (instead of 32768 - 61000)
There is no change on security aspects here, only some poor hashing
schemes could be eventually impacted by this change.
[1] : The odd/even property depends on ip_local_port_range values parity
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2015 17:03:31 +0000 (13:03 -0400)]
Merge branch 'ip_frag_next'
Florian Westphal says:
====================
net: force refragmentation for DF reassembed skbs
output path tests:
if (skb->len > mtu) ip_fragment()
This breaks connectivity in one corner case:
If the skb was reassembled, but has the DF bit set and ..
.. its reassembled size is <= outdev mtu ..
.. we will forward a DF packet larger than what the sender
transmitted on wire.
If a router later in the path can't forward this packet, it will send an
icmp error in response to an mtu that the original sender never exceeded.
This changes ipv4 defrag/output path to
a) force refragmentation for DF reassembled skbs and
b) set DF bit on all fragments when refragmenting if it was set on original
frags.
tested via:
from scapy.all import *
dip="10.23.42.2"
payload="A"*1400
packet=IP(dst=dip,id=12345,flags='DF')/UDP(sport=42,dport=42)/payload
frags=fragment(packet,fragsize=1200)
for fragment in frags:
send(fragment)
Without this patch, we generate fragments without df bit set based
on the outgoing device mtu when fragmenting after forwarding, ie.
IP (ttl 64, id 12345, offset 0, flags [+, DF], proto UDP (17), length 1204)
192.168.7.1.42 > 10.23.42.2.42: UDP, length 1400
IP (ttl 64, id 12345, offset 1184, flags [DF], proto UDP (17), length 244)
192.168.7.1 > 10.23.42.2: ip-proto-17
on ingress will either turn into
IP (ttl 63, id 12345, offset 0, flags [+], proto UDP (17), length 1396)
192.168.7.1.42 > 10.23.42.2.42: UDP, length 1400
IP (ttl 63, id 12345, offset 1376, flags [none], proto UDP (17), length 52)
(mtu 1400: We strip df and send larger fragment), or
IP (ttl 63, id 12345, offset 0, flags [DF], proto UDP (17), length 1428)
192.168.7.1.42 > 10.23.42.2.42: [udp sum ok] UDP, length 1400
if mtu is 1500. And in this case things break; router with a smaller mtu
will send icmp error, but original sender only sent packets <= 1204 byte.
With patch, we keep intent of such fragments and will emit DF-fragments
that won't exceed 1204 byte in size.
Joint work with Hannes Frederic Sowa.
Changes since v2:
- split unrelated patches from series
- rework changelog of patch #2 to better illustrate breakage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Fri, 22 May 2015 14:32:51 +0000 (16:32 +0200)]
ip_fragment: don't forward defragmented DF packet
We currently always send fragments without DF bit set.
Thus, given following setup:
mtu1500 - mtu1500:1400 - mtu1400:1280 - mtu1280
A R1 R2 B
Where R1 and R2 run linux with netfilter defragmentation/conntrack
enabled, then if Host A sent a fragmented packet _with_ DF set to B, R1
will respond with icmp too big error if one of these fragments exceeded
1400 bytes.
However, if R1 receives fragment sizes 1200 and 100, it would
forward the reassembled packet without refragmenting, i.e.
R2 will send an icmp error in response to a packet that was never sent,
citing mtu that the original sender never exceeded.
The other minor issue is that a refragmentation on R1 will conceal the
MTU of R2-B since refragmentation does not set DF bit on the fragments.
This modifies ip_fragment so that we track largest fragment size seen
both for DF and non-DF packets, and set frag_max_size to the largest
value.
If the DF fragment size is larger or equal to the non-df one, we will
consider the packet a path mtu probe:
We set DF bit on the reassembled skb and also tag it with a new IPCB flag
to force refragmentation even if skb fits outdev mtu.
We will also set DF bit on each fragment in this case.
Joint work with Hannes Frederic Sowa.
Reported-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
As you suggested, here is the helper function to avoid missing some RGMII
interface checks. Had to wait for net to be merged in net-next to avoid
submitting the same patch/commit.
Dan, you might want to rebase your dp83867 submission to use that helper
when you this patchset gets merged into net-next, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 26 May 2015 19:19:58 +0000 (12:19 -0700)]
net: phy: Add phy_interface_is_rgmii helper
RGMII interfaces come in 4 different flavors that the PHY library needs
to care about: regular RGMII (no delays), RGMII with either RX or TX
delay, and both. In order to avoid errors of checking only for one type
of RGMII interface and miss the 3 others, introduce a convenience
function which tests for all values.
Suggested-by: David S. Miller <davem@davemloft.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We used to get this indirectly I supposed, but no longer do.
Either way, an explicit include should have been done in the
first place.
net/ipv4/fib_trie.c: In function '__node_free_rcu':
>> net/ipv4/fib_trie.c:293:3: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(n);
^
net/ipv4/fib_trie.c: In function 'tnode_alloc':
>> net/ipv4/fib_trie.c:312:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
return vzalloc(size);
^
>> net/ipv4/fib_trie.c:312:3: warning: return makes pointer from integer without a cast
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 May 2015 15:55:28 +0000 (08:55 -0700)]
tcp: tcp_tso_autosize() minimum is one packet
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 May 2015 14:55:34 +0000 (07:55 -0700)]
tcp: fix/cleanup inet_ehash_locks_alloc()
If tcp ehash table is constrained to a very small number of buckets
(eg boot parameter thash_entries=128), then we can crash if spinlock
array has more entries.
While we are at it, un-inline inet_ehash_locks_alloc() and make
following changes :
- Budget 2 cache lines per cpu worth of 'spinlocks'
- Try to kmalloc() the array to avoid extra TLB pressure.
(Most servers at Google allocate 8192 bytes for this hash table)
- Get rid of various #ifdef
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Tue, 26 May 2015 09:40:19 +0000 (05:40 -0400)]
tipc: fix bug in link protocol message create function
In commit dd3f9e70f59f43a5712eba9cf3ee4f1e6999540c
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.
However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.
This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 May 2015 01:50:01 +0000 (18:50 -0700)]
net: fix inet_proto_csum_replace4() sparse errors
make C=2 CF=-D__CHECK_ENDIAN__ net/core/utils.o
...
net/core/utils.c:307:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:307:72: expected restricted __wsum [usertype] addend
net/core/utils.c:307:72: got restricted __be32 [usertype] from
net/core/utils.c:308:34: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:308:34: expected restricted __wsum [usertype] addend
net/core/utils.c:308:34: got restricted __be32 [usertype] to
net/core/utils.c:310:70: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:70: expected restricted __wsum [usertype] addend
net/core/utils.c:310:70: got restricted __be32 [usertype] from
net/core/utils.c:310:77: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:77: expected restricted __wsum [usertype] addend
net/core/utils.c:310:77: got restricted __be32 [usertype] to
net/core/utils.c:312:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:312:72: expected restricted __wsum [usertype] addend
net/core/utils.c:312:72: got restricted __be32 [usertype] from
net/core/utils.c:313:35: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:313:35: expected restricted __wsum [usertype] addend
net/core/utils.c:313:35: got restricted __be32 [usertype] to
Note we can use csum_replace4() helper
Fixes: 58e3cac5613aa ("net: optimise inet_proto_csum_replace4()") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wilson Kok [Mon, 25 May 2015 13:39:31 +0000 (06:39 -0700)]
bridge: skip fdb add if the port shouldn't learn
Check in fdb_add_entry() if the source port should learn, similar
check is used in br_fdb_update.
Note that new fdb entries which are added manually or
as local ones are still permitted.
This patch has been tested by running traffic via a bridge port and
switching the port's state, also by manually adding/removing entries
from the bridge's fdb.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 25 May 2015 23:02:21 +0000 (16:02 -0700)]
ipv6: ipv6_select_ident() returns a __be32
ipv6_select_ident() returns a 32bit value in network order.
Fixes: 286c2349f666 ("ipv6: Clean up ipv6_select_ident() and ip6_fragment()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2015 22:19:10 +0000 (18:19 -0400)]
Merge branch 'cpsw-cleanups'
Richard Cochran says:
====================
cpsw cleanups
While working on an out-of-tree customization, I noticed a few minor
problems in the cpsw code. This series cleans up the issues I found.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There
is no need to disable the dma interrupts twice. This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There
is no need to enable the dma interrupts twice. This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2015 22:17:09 +0000 (18:17 -0400)]
Merge branch 'rocker-cleanups'
Simon Horman says:
====================
rocker: unused parameter and const cleanups
This series provides some minor though verbose cleanup of rocker.
The second patch depends on the first though it could be rebased.
I had previously asked for v2 to be put on hold while some bugs I had found
in the rocker driver were shaken out. That has now happened and the bugs
turned out to be unrelated. Accordingly I am reposting the series.
* Changes v2 -> v3
- Rebase and update for new variables and parameters that may be const
* Changes v1 -> v2
- Found quite a few more variables and parameters to make const
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Mon, 25 May 2015 05:28:36 +0000 (14:28 +0900)]
rocker: mark parameters and local variables as const
Mark parameters and local variables as const where possible.
Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Mon, 25 May 2015 05:28:35 +0000 (14:28 +0900)]
rocker: remove unused rocker_port parameter from rocker_port_kfree
Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
irda: use msecs_to_jiffies for conversion to jiffies
API compliance scanning with coccinelle flagged:
./net/irda/timer.c:63:35-37: use of msecs_to_jiffies probably perferable
Converting milliseconds to jiffies by "val * HZ / 1000" technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases. Further the () around the arithmetic expression
was dropped.
Patch was compile tested for x86_64_defconfig + CONFIG_IRDA=m
Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
irda: irda-usb: use msecs_to_jiffies for conversions
API compliance scanning with coccinelle flagged:
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases.
in the current code:
mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
for HZ < 100 (e.g. CONFIG_HZ == 64|32 in alpha) this effectively results
in no delay at all.
Patch was compile tested for x86_64_defconfig (implies CONFIG_USB_IRDA=m)
Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Sat, 23 May 2015 01:12:34 +0000 (03:12 +0200)]
bridge: allow setting hash_max + multicast_router if interface is down
Network managers like netifd (used in OpenWRT for instance) try to
configure interface options after creation but before setting the
interface up.
Unfortunately the sysfs / bridge currently only allows to configure the
hash_max and multicast_router options when the bridge interface is up.
But since br_multicast_init() doesn't start any timers and only sets
default values and initializes timers it should be save to reconfigure
the default values after that, before things actually get active after
the bridge is set up.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 21 May 2015 22:44:16 +0000 (00:44 +0200)]
ipv6: don't increase size when refragmenting forwarded ipv6 skbs
since commit 6aafeef03b9d ("netfilter: push reasm skb through instead of
original frag skbs") we will end up sometimes re-fragmenting skbs
that we've reassembled.
ipv6 defrag preserves the original skbs using the skb frag list, i.e. as long
as the skb frag list is preserved there is no problem since we keep
original geometry of fragments intact.
However, in the rare case where the frag list is munged or skb
is linearized, we might send larger fragments than what we originally
received.
A router in the path might then send packet-too-big errors even if
sender never sent fragments exceeding the reported mtu:
mtu 1500 - 1500:1400 - 1400:1280 - 1280
A R1 R2 B
1 - A sends to B, fragment size 1400
2 - R2 sends pkttoobig error for 1280
3 - A sends to B, fragment size 1280
4 - R2 sends pkttoobig error for 1280 again because it sees fragments of size 1400.
make sure ip6_fragment always caps MTU at largest packet size seen
when defragmented skb is forwarded.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2015 17:25:35 +0000 (13:25 -0400)]
Merge branch 'ipv6_route_sharing'
Martin KaFai Lau says:
====================
ipv6: Only create RTF_CACHE route after encountering pmtu exception
v4 -> v5:
- Patch 1 is new. Clean up the ipv6_select_ident() and ip6_fragment().
- Further simplify the newly added rt6_get_pcpu_route(). If there is a
'prev' after cmpxchg, return prev instead of the newly created percpu
clone.
v3 -> v4:
- Patch 8 is new. It keeps track of the DST_NOCACHE routes in a list to handle
the iface down/unregister event.
- Remove rcu from the newly added rt6i_pcpu variable. It is not needed
because it has already been protected by the existing reader/writer lock.
- Thanks to 'Julian Anastasov <ja@ssi.bg>' for testing the FLOWI_FLAG_KNOWN_NH
patches.
v2 -> v3:
- Patch 5 to 7 are new. They take care of cases where the daddr in
skb is not the one used to do the route look-up. There is also
related changes to rt6_nexthop() since v2 which is in patch 2/9.
Thanks to 'Julian Anastasov <ja@ssi.bg>' for pointing it out.
- Fix a few problems in __ip6_rt_update_pmtu(), like setting the expire
and mtu before inserting to the tree and don't do dst_destroy() after
tree insertion failure. Also update the rt6i_pmtu in fib6_add_rt2node().
Thanks to 'Steffen Klassert <steffen.klassert@secunet.com>' for pointing
it out.
- Merge ip6_pmtu_rt_cache_alloc() into ip6_rt_cache_alloc().
v1 -> v2:
- Move the /128 route bug fixes to another series (accepted).
- Create a function for checking (rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY)).
- Avoid shuffling the skb network_header. Instead, change the function
signature to take iph instead of skb.
- Many Thanks to 'Hannes Frederic Sowa <hannes@stressinduktion.org>' on
reviewing v1 and v2 and giving advice.
--Martin
~~~ start: v1 compose message (with the out-dated parts removed) ~~~
This series is to avoid creating a RTF_CACHE route whenever we are consulting
the fib6 tree with a new destination. Instead, only create RTF_CACHE route
when we see a pmtu exception.
Out of all ipv6 RTF_CACHE routes that are created, the percentage that has a
different mtu is very small. In one of our end-user facing proxy server,
only 1k out of 80k RTF_CACHE routes have a smaller MTU. For our DC
traffic, there is no mtu exception.
A large fib6 tree has problems like, 'ip -6 r show' takes a long time.
gc may kick in too often. Also, when a service has restarted and a lot
of new TCP conn requests come in, it creates pressure on the tree by inserting
a lot of RTF_CACHE in a short time and it currently requires a write lock
to do that.
The first few patches are prep works to remove assumption that the
returned rt is always RTF_CACHE.
The patch 'ipv6: Only create RTF_CACHE routes after encountering pmtu exception'
do the lazy RTF_CACHE route creation.
The following patches added percpu rt to compensate the performance loss after
doing the RTF_CACHE lazy creation.
Here is some numbers of the udpflood test. The udpflood has been
slightly modified to have a time limit instead of count limit.
A /64 via gateway route is used for the test. Each udpflood uses 10000 dst
addresses. The dst addresses of different udpflood processes do not overlap
with each other.
Martin KaFai Lau [Sat, 23 May 2015 03:56:06 +0000 (20:56 -0700)]
ipv6: Create percpu rt6_info
After the patch
'ipv6: Only create RTF_CACHE routes after encountering pmtu exception',
we need to compensate the performance hit (bouncing dst->__refcnt).
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:05 +0000 (20:56 -0700)]
ipv6: Break up ip6_rt_copy()
This patch breaks up ip6_rt_copy() into ip6_rt_copy_init() and
ip6_rt_cache_alloc().
In the later patch, we need to create a percpu rt6_info copy. Hence,
refactor the common rt6_info init codes to ip6_rt_copy_init().
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:04 +0000 (20:56 -0700)]
ipv6: Keep track of DST_NOCACHE routes in case of iface down/unregister
This patch keeps track of the DST_NOCACHE routes in a list and replaces its
dev with loopback during the iface down/unregister event.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:03 +0000 (20:56 -0700)]
ipv6: Create RTF_CACHE clone when FLOWI_FLAG_KNOWN_NH is set
This patch always creates RTF_CACHE clone with DST_NOCACHE
when FLOWI_FLAG_KNOWN_NH is set so that the rt6i_dst is set to
the fl6->daddr.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Julian Anastasov <ja@ssi.bg> Tested-by: Julian Anastasov <ja@ssi.bg> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:02 +0000 (20:56 -0700)]
ipv6: Set FLOWI_FLAG_KNOWN_NH at flowi6_flags
The neighbor look-up used to depend on the rt6i_gateway (if
there is a gateway) or the rt6i_dst (if it is a RTF_CACHE clone)
as the nexthop address. Note that rt6i_dst is set to fl6->daddr
for the RTF_CACHE clone where fl6->daddr is the one used to do
the route look-up.
Now, we only create RTF_CACHE clone after encountering exception.
When doing the neighbor look-up with a route that is neither a gateway
nor a RTF_CACHE clone, the daddr in skb will be used as the nexthop.
In some cases, the daddr in skb is not the one used to do
the route look-up. One example is in ip_vs_dr_xmit_v6() where the
real nexthop server address is different from the one in the skb.
This patch is going to follow the IPv4 approach and ask the
ip6_pol_route() callers to set the FLOWI_FLAG_KNOWN_NH properly.
In the next patch, ip6_pol_route() will honor the FLOWI_FLAG_KNOWN_NH
and create a RTF_CACHE clone.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Julian Anastasov <ja@ssi.bg> Tested-by: Julian Anastasov <ja@ssi.bg> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:01 +0000 (20:56 -0700)]
ipv6: Add rt6_get_cookie() function
Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie. Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:56:00 +0000 (20:56 -0700)]
ipv6: Only create RTF_CACHE routes after encountering pmtu exception
This patch creates a RTF_CACHE routes only after encountering a pmtu
exception.
After ip6_rt_update_pmtu() has inserted the RTF_CACHE route to the fib6
tree, the rt->rt6i_node->fn_sernum is bumped which will fail the
ip6_dst_check() and trigger a relookup.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:55:59 +0000 (20:55 -0700)]
ipv6: Combine rt6_alloc_cow and rt6_alloc_clone
A prep work for creating RTF_CACHE on exception only. After this
patch, the same condition (rt->rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY))
is checked twice. This redundancy will be removed in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:55:58 +0000 (20:55 -0700)]
ipv6: Remove external dependency on rt6i_gateway and RTF_ANYCAST
When creating a RTF_CACHE route, RTF_ANYCAST is set based on rt6i_dst.
Also, rt6i_gateway is always set to the nexthop while the nexthop
could be a gateway or the rt6i_dst.addr.
After removing the rt6i_dst and rt6i_src dependency in the last patch,
we also need to stop the caller from depending on rt6i_gateway and
RTF_ANYCAST.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:55:57 +0000 (20:55 -0700)]
ipv6: Remove external dependency on rt6i_dst and rt6i_src
This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address. The dst and src can be recovered from
the calling site.
We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Sat, 23 May 2015 03:55:56 +0000 (20:55 -0700)]
ipv6: Clean up ipv6_select_ident() and ip6_fragment()
This patch changes the ipv6_select_ident() signature to return a
fragment id instead of taking a whole frag_hdr as a param to
only set the frag_hdr->identification.
It also cleans up ip6_fragment() to obtain the fragment id at the
beginning instead of using multiple "if" later to check fragment id
has been generated or not.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 22 May 2015 23:10:07 +0000 (01:10 +0200)]
test_bpf: add more eBPF jump torture cases
Add two more eBPF test cases for JITs, i.e. the second one revealed a
bug in the x86_64 JIT compiler, where only an int3 filled image from
the allocator was emitted and later wrongly set by the compiler as the
bpf_func program code since optimization pass boundary was surpassed
w/o actually emitting opcodes.
Reference: http://thread.gmane.org/gmane.linux.network/364729 Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches are included in this driver update series:
- Retrieve and set an additional hardware feature setting
- Fix the initial mode/speed determination when auto-negotiation is
disabled
- Add additional netif_dbg support to the driver
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 22 May 2015 21:32:14 +0000 (16:32 -0500)]
amd-xgbe: Fix initial mode when auto-negotiation is disabled
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 22 May 2015 21:32:09 +0000 (16:32 -0500)]
amd-xgbe: Add setting of a missing hardware feature
The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 21 May 2015 22:06:40 +0000 (00:06 +0200)]
ip: reject too-big defragmented DF-skb when forwarding
Send icmp pmtu error if we find that the largest fragment of df-skb
exceeded the output path mtu.
The ip output path will still catch this later on but we can avoid the
forward/postrouting hook traversal by rejecting right away.
This is what ipv6 already does.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: af_unix: implement splice for stream af_unix sockets
unix_stream_recvmsg is refactored to unix_stream_read_generic in this
patch and enhanced to deal with pipe splicing. The refactoring is
inneglible, we mostly have to deal with a non-existing struct msghdr
argument.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare skb_splice_bits to be able to deal with AF_UNIX sockets.
AF_UNIX sockets don't use lock_sock/release_sock and thus we have to
use a callback to make the locking and unlocking configureable.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements sendpage support for AF_UNIX SOCK_STREAM
sockets. This is also required for a complete splice implementation.
The implementation is a bit tricky because we append to already existing
skbs and so have to hold unix_sk->readlock to protect the reading side
from either advancing UNIXCB.consumed or freeing the skb at the socket
receive tail.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2015 03:23:01 +0000 (23:23 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2015 03:05:10 +0000 (23:05 -0400)]
Merge branch 'mlx4-next'
Or Gerlitz says:
====================
mlx4: Enable single ported VFs over IB ports
This series further enhances the support for mlx4 single ported VFs
introduced in 3.15 to work over IB ports too.
Just as quick reminder, the ConnectX3 device family exposes one PCI device
which serves both ports.
This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.
Since all the VF interaction with the firmware passes through the PF
driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:10 +0000 (15:14 +0300)]
net/mlx4_core: Enable single ported IB VFs
Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.
SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:09 +0000 (15:14 +0300)]
net/mlx4_core: Adjust the schedule queue port in reset-to-init too
It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.
Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:08 +0000 (15:14 +0300)]
net/mlx4_core: Adjust the schedule queue port for single ported IB VFs
Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.
To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:07 +0000 (15:14 +0300)]
net/mlx4_core: Modify port values when generting EQEs for VFs
As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.
This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.
(1) make sure that events are generated only for VFs sitting on
the relevant physical port (under the ALL_SLAVES flow).
(2) before generating the event, convert from physical (one or two)
to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:06 +0000 (15:14 +0300)]
IB/mlx4: Convert slave port before building address-handle
When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).
This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.
So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.
Fixes: 449fc48866f7 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 21 May 2015 12:14:05 +0000 (15:14 +0300)]
net/mlx4_core: Enhance the MAD_IFC wrapper to convert VF port to physical
Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.
It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.
Fixes: 449fc48866f7 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 May 2015 03:59:23 +0000 (23:59 -0400)]
Merge branch 'pktgen-new-scripts'
Jesper Dangaard Brouer says:
====================
pktgen: cleanups and introducing new samples/pktgen scripts
v3:
- Aborted v2 send due it was not generating diff stat
(this is a bug in stg-mail, if not in the root directory)
v2: address nitpicks from Cong Wang
- Remove useless cat's, but keep them for old pgset()
- Comment on: Due to pgctrl, cannot use exit code $? from grep
- Use arithmetic compare in pktgen_sample03_burst_single_flow.sh
This patchset is focused on making pktgen easier to use and better
documented. It contains a number of documentation updates and minor
changes to pktgen. The major contribution is introduction of common
helper function for sample scripts.
Instead of the old pgset() function, three new shell functions for
configuring the different components of pktgen are introduced:
pg_ctrl(), pg_thread() and pg_set().
The new functions correspond to pktgens different components.
* pg_ctrl() control "pgctrl" (/proc/net/pktgen/pgctrl)
* pg_thread() control the kernel threads and binding to devices
* pg_set() control setup of individual devices
Helpers also provide consistent parameter parsing across the sample
scripts.
This script pktgen_bench_xmit_mode_netif_receive.sh is a benchmark
script, which can be used for benchmarking part of the network stack.
This can be used for performance improving or catching regression in
that area.
The script is developed for benchmarking ingress qdisc path, original
idea by Alexei Starovoitov. This script don't really need any
hardware. This is achieved via the recently introduced stack inject
feature "xmit_mode netif_receive". See commit 62f64aed622b6 ("pktgen:
introduce xmit_mode '<start_xmit|netif_receive>'").
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pktgen samples script pktgen_sample03_burst_single_flow.sh
that demonstrates how to acheive maximum performance.
If correctly tuned[1] single CPU 10Gbit/s wirespeed small pkts is
possible[2] which is 14.88Mpps. The trick is to take advantage of the
"burst" feature introduced in commit 38b2cf2982dc73 ("net: pktgen:
packet bursting via skb->xmit_more").
Add the pktgen samples script pktgen_sample02_multiqueue.sh that
demonstrates generating packets on multiqueue NICs.
Specifically notice the options "-t" that specifies how many
kernel threads to activate. Also notice the flag QUEUE_MAP_CPU,
which cause the SKB TX queue to be mapped to the CPU running the
kernel thread. For best scalability people are also encourage to
map NIC IRQ /proc/irq/*/smp_affinity to CPU number.
Usage example with "-t" 4 threads and help:
./pktgen_sample02_multiqueue.sh -i eth4 -m 00:1B:21:3C:9D:F8 -t 4
Add the first basic pktgen samples script pktgen_sample01_simple.sh,
which demonstrates the a simple use of the helper functions.
Removing pktgen.conf-1-1 as that example should be covered now.
The naming scheme pktgen_sampleNN, where NN is a number, should encourage
reading the samples in a specific order.
Script cause pktgen sending with a single thread and single interface,
and introduce flow variation via random UDP source port.
Usage example and help:
./pktgen_sample01_simple.sh -i eth4 -m 00:1B:21:3C:9D:F8 -d 192.168.8.2
pktgen: new pktgen helper functions for samples scripts
Preparing for removing existing samples/pktgen/ scripts, and
replacing these with easier to use samples.
This commit provides two helper shell files, that can
be "included" by shell source'ing. Namely "functions.sh"
and "parameters.sh".
The parameters.sh file support easy and consistant parameter
parsing across the sample scripts. Usage example is printed on
errors.
The functions.sh file provides, three new shell functions for
configuring the different components of pktgen: pg_ctrl(),
pg_thread() and pg_set(). A slightly improved version of the old
pgset() function is also provided for backwards compat.
The new functions correspond to pktgens different components.
* pg_ctrl() control "pgctrl" (/proc/net/pktgen/pgctrl)
* pg_thread() control the kernel threads and binding to devices
* pg_set() control setup of individual devices
These changes are borrowed from:
https://github.com/netoptimizer/network-testing/tree/master/pktgen
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen: make /proc/net/pktgen/pgctrl report fail on invalid input
Giving /proc/net/pktgen/pgctrl an invalid command just returns shell
success and prints a warning in dmesg. This is not very useful for
shell scripting, as it can only detect the error by parsing dmesg.
Instead return -EINVAL when the command is unknown, as this provides
userspace shell scripting a way of detecting this.
Also bump version tag to 2.75, because (1) reading /proc/net/pktgen/pgctrl
output this version number which would allow to detect this small
semantic change, and (2) because the pktgen version tag have not been
updated since 2010.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen: document ability to add same device to several threads
The pktgen.txt documentation still claimed that adding same device to
multiple threads were not supported, but it have been since 2008 via
commit e6fce5b916cd7 ("pktgen: multiqueue etc.").
Document this and describe the naming scheme dev@X, as the procfile name
still need to be unique.
Fixes: e6fce5b916cd7 ("pktgen: multiqueue etc.") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 May 2015 00:34:24 +0000 (17:34 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Linus Torvalds [Fri, 22 May 2015 22:15:30 +0000 (15:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Linus Torvalds [Fri, 22 May 2015 21:49:55 +0000 (14:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.
Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Reported-by: Dominick Grift <dac.override@gmail.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: core: 'ethtool' issue with querying phy settings
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com> Reviewed-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Holzheu [Fri, 22 May 2015 15:36:40 +0000 (08:36 -0700)]
test_bpf: Add backward jump test case
Currently the testsuite does not have a test case with a backward jump.
The s390x JIT (kernel 4.0) had a bug in that area.
So add one new test case for this now.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:10 +0000 (09:22 -0500)]
net: macb: Disable half duplex gigabit on Zynq
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:09 +0000 (09:22 -0500)]
net: macb: Document zynq gem dt binding
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Fri, 22 May 2015 11:40:09 +0000 (13:40 +0200)]
ipv4: fill in table id when replacing a route
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 22 May 2015 11:15:22 +0000 (13:15 +0200)]
cdc_ncm: Fix tx_bytes statistics
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Reported-by: Florian Bruhin <me@the-compiler.org> Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 22 May 2015 09:05:58 +0000 (11:05 +0200)]
flow_dissector: do not break if ports are not needed in flowlabel
This restored previous behaviour. If caller does not want ports to be
filled, we should not break.
Fixes: 06635a35d13d ("flow_dissect: use programable dissector in skb_flow_dissect and friends") Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 May 2015 04:51:19 +0000 (21:51 -0700)]
tcp: fix a potential deadlock in tcp_get_info()
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Fri, 22 May 2015 03:31:03 +0000 (13:31 +1000)]
Merge tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel into drm-fixes
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
Florian Westphal [Thu, 21 May 2015 00:26:24 +0000 (02:26 +0200)]
net: sched: pkt_cls: remove unused macros from uapi
Jamal points out that this header also contains kernel internal magic that
cannot be used from userspace for anything meaningful.
Lets remove what the kernel doesn't use anymore and wrap remainder with
__KERNEL__.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log