ENGR00141647 AUDIO,SGTL5000: Fix codec error after reset
sgtl5000 codec not work after board reset, this is caused by
sgtl5000 using register address step is 2, and snd-soc-core can't
handle this as we expect, so we have to fill the register cache by
reading register out when initialization instead of providing a default
value array.
Huang Shijie [Mon, 30 Aug 2010 01:51:18 +0000 (09:51 +0800)]
ENGR00141399-5 OCOTP: add the ocotp driver
Add a new driver for On-Chip OTP controller. The driver
will register all the register names of all the banks to /sys/.
You can use the following commands to manipulate the OTP banks:
Richard Zhao [Tue, 22 Mar 2011 02:22:15 +0000 (10:22 +0800)]
ENGR00141399-2 iMX5x: add clock debug information
Expose clock debug information to debugfs, which makes it easier for clock
system debug by using tools like powerdebug developed by Linaro power
management group.
For long term, this can go into common clock framework, but so far it depends
on the process of common clk API development. Once the common clk API is
ready in upstream, the clock debug information will be based on it too.
The implementation based on common clk API had also been finished and
reviewed with Jeremy.
ARM: iMX5x: fix clock debug enable_count error
Signed-off-by: Yong Shen <yong.shen@linaro.org> Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Jason Chen <b02280@freescale.com>
Frank Li [Tue, 29 Mar 2011 01:45:35 +0000 (09:45 +0800)]
ENGR00141217-8 ASoC: SGTL5000: Add DAP support for sgtl5000 codec
upgrade to 2.6.38 kernel
Add Digital Audio Process(DAP) for sgtl5000 codec
Audio: imx53,loco,audio: make Loco sgtl5000 codec work
config audmux when ssi probed, and fix sdma watermark settings
Jason Chen [Wed, 23 Feb 2011 09:31:54 +0000 (17:31 +0800)]
ENGR00141217-5 IPU\VPU\GPU: upgrade to 2.6.38
Add drivers/mxc
Add drivers/video/mxc
Add drivers/media/mxc
fb device: change acquire_console_sem to console_lock
And release_console_sem to console_unlock
Add DMA Zone support
Add TVE driver, add regulator
Add hdmi support
Add VPU
Frank Li [Tue, 22 Feb 2011 09:34:58 +0000 (17:34 +0800)]
ENGR00141217-3 MX53 MSL part upgrade to 2.6.38
imx51_babbage:
imx53_smd: add i2c device
imx53_smd: add i2c board device info
imx53_smd: add esdhc device support
imx53_smd: Add SRTC devices
imx53_smd: enable the AHCI SATA
imx53_smd: Add GPIO Keypad support
imx53_ard: enable ARD board bootup
imx53_ard: add ethernet pin mux
imx53_ard: add smsc911x device
imx53_loco: add i2c device
imx53_loco: change sii902x i2c device
imx53_loco: register v4l2 output device
imx53_loco: add srtc device
imx53_loco: enable the AHCI SATA
imx53_loco: Add GPIO Keypad support
imx53_evk: add evk and arm2 boards io setting and set up display
imx5: add ipu\vpu
imx5: clock.c: remove RATE_PROPAGATES
imx5: Add clock, dvfs, busfreq, sdram_autogating support.
imx5: fix warnings on boot
imx5: add v4l2 device
imx5: add board_is_rev support
imx5: Add sdma support for i.Mx53 and i.Mx51
imx5: add p1003
imx5: add ipuv3
imx5: add sata
imx5: add pmic board files
imx5: add pm function
imx5: add iram config
imx5: add gpu
imx5: fix clock debug enable_count error
imx53: add gpio irq support for mx53
imx53: change PWM backlight device register method to dynamic
imx53: change v4l2 device register method to dynamic
imx53: add vpu devices support
imx53: add dvfs-core and busfreq devices register method
imx53: Add usb devices
imx53: add i2c pad settings
imx53: add ssi support
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Jason Chen <b02280@freescale.com> Signed-off-by: Zeng Zhaoming <b32542@freescale.com> Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com> Signed-off-by: Zhang Yan <b34916@freescale.com>
Zhang Jiejing [Mon, 22 Nov 2010 09:14:32 +0000 (17:14 +0800)]
ENGR00133978 PM: add time sensitive debug function to suspend & resume
There was some driver is slow on suspend/resume,
but some embeded system like eReader,Cellphone
are time sensitive,this commit will report the slow
driver on suspend/resume, the default value is 500us(0.5ms)
Also, the threshold can be change by modify
'/sys/power/device_suspend_time_threshold' to change the threshold,
it is in microsecond.
The output is like:
PM: device platform:soc-audio.2 suspend too slow, takes 606.696 msecs
PM: device platform:mxc_sdc_fb.1 suspend too slow, takes 7.708 msecs
the default state of suspend driver is default off,
if you want to debug the suspend time, echo time in
microsecond(u Second) to /sys/powe/device_suspend_time_threshold
eg: I want to know which driver suspend & resume takes
more that 0.5 ms (500 us), you can just :
Richard Zhao [Wed, 21 Apr 2010 04:46:59 +0000 (12:46 +0800)]
ENGR00122691-1 Add atheros driver ath6kl
Integrate atheros driver package from atheros company.
It's mainly for AR6003.
NGR00132491-1 ath6kl upgrade: change Kconfig
This series of patches are for upgrading Atheros AR6003(ath6kl)
in 31 kernel to 35 kernel.
The WLAN_80211 config option has been changed to WLAN in 35 kernel.
Some i.MX parts (MX31, MX37) need to have usb host queue descriptors
and/or buffers in on-chip IRAM in cases of heavily loaded memory
system (i.e. large LCDs).
Enable partial low interrupt latency mode for ARM1136
Enable partial low interrupt latency mode for ARM1136
This patch is a workaround for the 364296 ARM1136 r0pX errata
(possible cache data corruption with hit-under-miss enabled). It sets
the undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Jason Liu [Wed, 26 Mar 2008 02:57:06 +0000 (21:57 -0500)]
ENGR00069937 Community patch for Fix mount error in case of MLC flash
Even though we don't use the OOB for MLC nand flash,
we should use the bad block information to skip the bad block.
Patch url:
http://patchwork.ozlabs.org/linux-mtd/patch?q=mlc&filter=none&id=15477
Author:Kyungmin Park
Read esd_csd info each time when cat boot_info
becasue user may change config affect esd_csd
value.
boot_info:0x07;
ALT_BOOT_MODE:1 - Supports alternate boot method
DDR_BOOT_MODE:1 - Supports alternate dual data rate during boot
HS_BOOTMODE:1 - Supports high speed timing during boot
boot_size:0512KB
boot_partition:0x48;
BOOT_ACK:1 - Boot acknowledge sent during boot operation
BOOT_PARTITION-ENABLE: 1 - Boot partition 1 enabled
PARTITION_ACCESS:0 - No access to boot partition
boot_bus:0x01
BOOT_MODE:0 - Use single data rate + backward compatible timings
in boot operation
RESET_BOOT_BUS_WIDTH:0 - Reset bus width to x1, single data rate
and backward compatible timings after boot operation
BOOT_BUS_WIDTH:1 - x4 (sdr/ddr) bus width in boot operation mode
Enable the configurations of the boot enable on the eMMC cards.
Add the interface that used to configure the boot_bus_width
In order to make sure that the re-read the ext-csd of card
can be completed successfully, add the method to wait for
the finish of the busy state.
NOTE:
The following are the valid inputs when configure the boot
bus width of the eMMC cards.
+--------------------------------------------------------------------+
| Bit7 Bit6 Bit5 | Bit4 Bit3 | Bit2 | Bit1 Bit0 |
|----------------|----------------------------------|----------------|
| X | BOOT_MODE | RESET_BOOT_BUS_WIDTH | BOOT_BUS_WIDTH |
+--------------------------------------------------------------------+
Bit [4:3] : BOOT_MODE (non-volatile)
0x0 : Use single data rate + backward compatible timings in boot
operation (default)
0x1 : Use single data rate + high speed timings in boot operation mode
0x2 : Use dual data rate in boot operation
0x3 : Reserved
Bit [2]: RESET_BOOT_BUS_WIDTH (non-volatile)
0x0 : Reset bus width to x1, single data rate and backward compatible
timings after boot operation (default)
0x1 : Retain boot bus width and boot mode after boot operation
Bit[1:0] : BOOT_BUS_WIDTH (non-volatile)
0x0 : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
0x1 : x4 (sdr/ddr) bus width in boot operation mode
0x2 : x8 (sdr/ddr) bus width in boot operation mode
0x3 : Reserved
The following are the valid inputs when configure the boot
partitions of the eMMC cards.
+------------------------------------------------------------+
| Bit7 | Bit6 | Bit5 Bit4 Bit3 | Bit2 Bit1 Bit0 |
|------|----------|-----------------------|------------------|
| X | BOOT_ACK | BOOT_PARTITION_ENABLE | PARTITION_ACCESS |
+------------------------------------------------------------+
Bit7: Reserved
Bit6: always set to vaule '1' when boot_part is enabled
Bit[5:3]:
0x0 : Device not boot enabled (default)
0x1 : Boot partition 1 enabled for boot
0x2 : Boot partition 2 enabled for boot
0x7 : User area enabled for boot
Bit[2:0]:
0x0 : No access to boot partition (default)
0x1 : R/W boot partition 1
0x2 : R/W boot partition 2
So only the '0, 1, 2; 8, 9, 10; 16, 17, 18; 56, 57, 58' are
valid parameters when configure the boot_partiton.
Richard Zhu [Fri, 23 Jul 2010 08:38:06 +0000 (16:38 +0800)]
ENGR00125411 eMMC: Boot Partition switch func used in MFG tool
User can get eMMC partitions info from user space layer in
linux OS enviroment.
User can do switch operations between the eMMC boot partitions
and the user partition.
User can access the eMMC boot partitions from user space layer
in linux OS enviroment.
NOTE:This func had been verified on TOSHIBA eMMC44 card only.
Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Rob Herring <r.herring@freescale.com>
When called for anonymous (non-shared) mappings, hugetlb_reserve_pages()
does a resv_map_alloc(). It depends on code in hugetlbfs's
vm_ops->close() to release that allocation.
However, in the mmap() failure path, we do a plain unmap_region() without
the remove_vma() which actually calls vm_ops->close().
This is a decent fix. This leak could get reintroduced if new code (say,
after hugetlb_reserve_pages() in hugetlbfs_file_mmap()) decides to return
an error. But, I think it would have to unroll the reservation anyway.
The transfer of ->flags causes some of the static mapping virtual
addresses to be prematurely freed (before the mapping is removed) because
VM_LAZY_FREE gets "set" if tmp->flags has VM_IOREMAP set. This might
cause subsequent vmalloc/ioremap calls to fail because it might allocate
one of the freed virtual address ranges that aren't unmapped.
va->flags has different types of flags from tmp->flags. If a region with
VM_IOREMAP set is registered with vm_area_add_early(), it will be removed
by __purge_vmap_area_lazy().
Fix vmalloc_init() to correctly initialize vmap_area for the given
vm_struct.
Also initialise va->vm. If it is not set, find_vm_area() for the early
vm regions will always fail.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com> Cc: "Olav Haugan" <ohaugan@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmap_area->private is void* but we don't use the field for various purpose
but use only for vm_struct. So change it to a vm_struct* with naming to
improve for readability and type checking.
Signed-off-by: Minchan Kim <minchan@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Virtual Machines with emulated e1000 network adapter running on Parallels'
server were seeing kernel panics due to the e1000 driver dereferencing an
unexpected NULL pointer retrieved from buffer_info->skb.
The problem has been addressed for the e1000e driver, but not for the e1000.
Since the two drivers share similar code in the affected area, a port of the
following e1000e driver commit solves the issue for the e1000 driver:
e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Dean Nelson <dnelson@redhat.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Roman Kagan <rkagan@parallels.com>
Now we store attr->ino at inode->i_ino, return attr->ino at the
first time and then return inode->i_ino if the attribute timeout
isn't expired. That's wrong on 32 bit platforms because attr->ino
is 64 bit and inode->i_ino is 32 bit in this case.
Fix this by saving 64 bit ino in fuse_inode structure and returning
it every time we call getattr. Also squash attr->ino into inode->i_ino
explicitly.
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: Robert Richter <robert.richter@amd.com>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It does not get processed because sched_domain_level_max is 0 at the
time that setup_relax_domain_level() is run.
Simply accept the value as it is, as we don't know the value of
sched_domain_level_max until sched domain construction is completed.
Fix sched_relax_domain_level in cpuset. The build_sched_domain() routine calls
the set_domain_attribute() routine prior to setting the sd->level, however,
the set_domain_attribute() routine relies on the sd->level to decide whether
idle load balancing will be off/on.
Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On high CPU load the accumulating values in the running_avg_cap
register are very low (below 10), so averaging them too early leads
to unnecessary poor output resolution. Since we pretend to output
micro-Watt we better keep all the bits we have as long as possible.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 32 bit variant of cbc(aes) decrypt is using instructions requiring
128 bit aligned memory locations but fails to ensure this constraint in
the code. Fix this by loading the data into intermediate registers with
load unaligned instructions.
This fixes reported general protection faults related to aesni.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43223 Reported-by: Daniel <garkein@mailueberfall.de> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description] Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory the parameter __key points to is used as an iterator in
btree_get_prev(), so if we save off a bkey() pointer in retry_key and
then assign that to __key, we'll end up corrupting the btree internals
when we do eg
longcpy(__key, bkey(geo, node, i), geo->keylen);
to return the key value. What we should do instead is use longcpy() to
copy the key value that retry_key points to __key.
This can cause a btree to get corrupted by seemingly read-only
operations such as btree_for_each_safe.
[akpm@linux-foundation.org: avoid the double longcpy()] Signed-off-by: Roland Dreier <roland@purestorage.com> Acked-by: Joern Engel <joern@logfs.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7990696 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags. So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to regenerate the sysfs files when the capacity units
change, avoid the update otherwise.
The origin of this issue is dates way back to 2.6.38: da8aeb92d4853f37e281f11fddf61f9c7d84c3cd
(ACPI / Battery: Update information on info notification and resume)
Signed-off-by: Andy Whitcroft <apw@canonical.com> Tested-by: Ralf Jung <post@ralfj.de> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't have references held on pages in the s_buddy_cache while we are
trying to truncate its pages and put the inode. All the pages must be
gone before we reach clear_inode. This can only be gauranteed if we
can prevent new users from grabbing references to s_buddy_cache's pages.
The original bug can be reproduced and the bug fix can be verified by:
while true; do mount -t ext4 /dev/ram0 /export/hda3/ram0; \
umount /export/hda3/ram0; done &
while true; do cat /proc/fs/ext4/ram0/mb_groups; done
In commit 353eb83c we removed i_state_flags with 64-bit longs, But
when handling the EXT4_IOC_SETFLAGS ioctl, we replace i_flags
directly, which trashes the state flags which are stored in the high
32-bits of i_flags on 64-bit platforms. So use the the
ext4_{set,clear}_inode_flags() functions which use atomic bit
manipulation functions instead.
Reported-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ext4_error() function is missing a call to save_error_info().
Since this is the function which marks the file system as containing
an error, this oversight (which was introduced in 2.6.36) is quite
significant, and should be backported to older stable kernels with
high urgency.
Corrects the function that determines the esp payload size. The calculations
done in esp{4,6}_get_mtu() lead to overlength frames in transport mode for
certain mtu values and suboptimal frames for others.
According to what is done, mainly in esp{,6}_output() and tcp_mtu_to_mss(),
net_header_len must be taken into account before doing the alignment
calculation.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the beginning of __skb_cow, headroom gets set to a minimum of
NET_SKB_PAD. This causes unnecessary reallocations if the buffer was not
cloned and the headroom is just below NET_SKB_PAD, but still more than the
amount requested by the caller.
This was showing up frequently in my tests on VLAN tx, where
vlan_insert_tag calls skb_cow_head(skb, VLAN_HLEN).
Locally generated packets should have enough headroom, and for forward
paths, we already have NET_SKB_PAD bytes of headroom, so we don't need to
add any extra space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Vlad Yaseivch <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
commit c57b5468406 (pktgen: fix crash at module unload) did a very poor
job with list primitives.
1) list_splice() arguments were in the wrong order
2) list_splice(list, head) has undefined behavior if head is not
initialized.
3) We should use the list_splice_init() variant to clear pktgen_threads
list.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hold the pktgen_thread_lock while splicing pktgen_threads, and test
pktgen_exiting in pktgen_device_event() to make unload faster.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An application may call connect() to disconnect a socket using an
address with family AF_UNSPEC. The L2TP IP sockets were not handling
this case when the socket is not bound and an attempt to connect()
using AF_UNSPEC in such cases would result in an oops. This patch
addresses the problem by protecting the sk_prot->disconnect() call
against trying to unhash the socket before it is bound.
The patch also adds more checks that the sockaddr supplied to bind()
and connect() calls is valid.
Since commit ad0081e43a
"ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed"
the fragment of packets is incorrect.
because tunnel mode needs IPsec headers and trailer for all fragments,
while on transport mode it is sufficient to add the headers to the
first fragment and the trailer to the last.
so modify mtu and maxfraglen base on ipsec mode and if fragment is first
or last.
with my test,it work well(every fragment's size is the mtu)
and does not trigger slow fragment path.
Changes from v1:
though optimization, mtu_prev and maxfraglen_prev can be delete.
replace xfrm mode codes with dst_entry's new frag DST_XFRM_TUNNEL.
add fuction ip6_append_data_mtu to make codes clearer.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
<3>[23898.789643] BUG: sleeping function called from invalid context at
/data/buildbot/workdir/ics/hardware/intel/linux-2.6/arch/x86/mm/fault.c:1103
<3>[23898.862215] in_atomic(): 0, irqs_disabled(): 0, pid: 10526, name:
Thread-6683
<4>[23898.967805] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.258526] Pid: 10526, comm: Thread-6683 Tainted: G W 3.0.8-137685-ge7742f9 #1
<4>[23899.357404] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.904225] Call Trace:
<4>[23899.989209] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.000416] [<c1238c2a>] __might_sleep+0x10a/0x110
<4>[23900.007357] [<c1228021>] do_page_fault+0xd1/0x3c0
<4>[23900.013764] [<c18e9ba9>] ? restore_all+0xf/0xf
<4>[23900.024024] [<c17c007b>] ? napi_complete+0x8b/0x690
<4>[23900.029297] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.123739] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.128955] [<c18ea0c3>] error_code+0x5f/0x64
<4>[23900.133466] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.138450] [<c17f6298>] ? __ip_route_output_key+0x698/0x7c0
<4>[23900.144312] [<c17f5f8d>] ? __ip_route_output_key+0x38d/0x7c0
<4>[23900.150730] [<c17f63df>] ip_route_output_flow+0x1f/0x60
<4>[23900.156261] [<c181de58>] ip4_datagram_connect+0x188/0x2b0
<4>[23900.161960] [<c18e981f>] ? _raw_spin_unlock_bh+0x1f/0x30
<4>[23900.167834] [<c18298d6>] inet_dgram_connect+0x36/0x80
<4>[23900.173224] [<c14f9e88>] ? _copy_from_user+0x48/0x140
<4>[23900.178817] [<c17ab9da>] sys_connect+0x9a/0xd0
<4>[23900.183538] [<c132e93c>] ? alloc_file+0xdc/0x240
<4>[23900.189111] [<c123925d>] ? sub_preempt_count+0x3d/0x50
Function free_fib_info resets nexthop_nh->nh_dev to NULL before releasing
fi. Other cpu might be accessing fi. Fixing it by delaying the releasing.
With the patch, we ran MTBF testing on Android mobile for 12 hours
and didn't trigger the issue.
Thank Eric for very detailed review/checking the issue.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com> Signed-off-by: Kun Jiang <kunx.jiang@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this bit sets we get broken rendering and
lockups.
fglrx sets this bit.
Bugs that should be fixed by this patch :
https://bugs.freedesktop.org/show_bug.cgi?id=49792
https://bugzilla.kernel.org/show_bug.cgi?id=43207
https://bugs.freedesktop.org/show_bug.cgi?id=39282
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to program an additional VM register. This doesn't not currently
cause any problems, but allows us to program the proper backend
map in a subsequent patch which should improve performance on these
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__mnt_make_shortterm() in there undoes the effect of __mnt_make_longterm()
we'd done back when we set ->mnt_ns non-NULL; it should not be done to
vfsmounts that had never gone through commit_tree() and friends. Kudos to
lczerner for catching that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in e.g. some Acer Aspire 7750G.
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
projects / karo-tx-linux.git / log