The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma: use fallback sprom if sprom on card was not valid
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
This is the case for the PCIe cards in my ASUS RT-N66U (BCM4706 + 2
times BCM4331) and I have heard of someone having the same problem with
an other PCIe card connected to an other Broadcom SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some devices which are able to boot from nand flash and other
are using a serial flash for booting. Add a bool to indicate that the
device is booted from that flash chip and not from some other chip also
connected to the SoC. This is needed to find the nvram, as it is stored
on the flash the devices booted from.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe host driver and the chip common initialisation accesses the
sprom struct, but it is not initialized when these functions are run.
Move the sprom parsing up in to do it earlier.
As we need the chip common core rev and some other attributes from the
chip common core, the early initialization is done before accessing the
sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma: just do the necessary things in early register on SoCs
Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marco Porsch [Wed, 10 Oct 2012 19:39:50 +0000 (12:39 -0700)]
mac80211: make client powersave independent of interface type
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
nl/cfg80211: force scan using an AP vif if requested
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bluetooth: AMP: Get amp_mgr reference in HS hci_conn
When assigning amp_mgr in hci_conn (type AMP_LINK) get also reference.
In hci_conn_del those references would be put for both conn types
AMP_LINK and ACL_LINK associated with amp_mgr.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Beni Lev [Tue, 31 Jul 2012 15:48:27 +0000 (18:48 +0300)]
cfg80211: add tracing to rdev-ops
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.
Signed-off-by: Beni Lev <beni.lev@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Hila Gonen <hila.gonen@intel.com> Tested-by: Hila Gonen <hila.gonen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith Manoharan [Thu, 18 Oct 2012 04:49:28 +0000 (10:19 +0530)]
cfg80211: Disallow HT/WEP in IBSS mode
Currently, a user is allowed to choose a HT operating channel
with WEP when creating an IBSS network. WEP is not allowed
in HT configuration - this patch ensures that such requests
are denied.
Signed-off-by: Sujith Manoharan <c_manoha@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 30 Sep 2012 15:08:35 +0000 (17:08 +0200)]
mac80211: remove some unused code
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 30 Sep 2012 15:07:19 +0000 (17:07 +0200)]
mac80211: remove unimplemented mesh vendor sync
There's no vendor-specific mesh sync implemented
and there don't need to be dummy handlers that
only print messages, so remove that code. While
at it, also constify the mesh sync ops.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WLAN_EID_WPA and WLAN_EID_GENERIC mapped to the same value
as WLAN_EID_VENDOR_SPECIFIC. The last one being more in line
with the standard specification. Removing WLAN_EID_WPA and
WLAN_EID_GENERIC as there are no longer drivers using these.
Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 12 Oct 2012 10:28:15 +0000 (12:28 +0200)]
wireless: gelic: make use of WLAN_EID_VENDOR_SPECIFIC
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 12 Oct 2012 10:28:14 +0000 (12:28 +0200)]
wireless: drivers: make use of WLAN_EID_VENDOR_SPECIFIC
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi> Cc: Dan Williams <dcbw@redhat.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl] Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex] Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00] Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith Manoharan [Fri, 12 Oct 2012 12:05:45 +0000 (17:35 +0530)]
mac80211: Notify new IBSS network creation
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.
Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:35 +0000 (21:03 -0700)]
mac80211: add support for tx to abort low priority scan requests
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:34 +0000 (21:03 -0700)]
cfg80211: add support for flushing old scan results
Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).
For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.
This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: Sam Leffler <sleffler@chromium.org> Tested-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 12 Oct 2012 08:55:53 +0000 (10:55 +0200)]
wireless: use OR operation to set wiphy features
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:32 +0000 (21:03 -0700)]
cfg80211: add scan flag to indicate its priority
Add NL80211_SCAN_FLAG_LOW_PRIORITY flag support. It tells drivers
that this is a low priority scan request, so that they can take
necessary action.
Drivers need to advertise low priority scan capability during
registration.
Signed-off-by: Sam Leffler <sleffler@chromium.org> Tested-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:31 +0000 (21:03 -0700)]
{nl,cfg}80211: add a flags word to scan requests
Add a flags word to direct and scheduled scan requests; it will
be used for control of optional behaviours such as flushing the
bss cache prior to doing a scan.
Signed-off-by: Sam Leffler <sleffler@chromium.org> Tested-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_sta_expire will be called by both IBSS and mesh
interfaces to account for inactive stations, so it would be more
appropriate to use sta_dbg instead of ibss_dbg.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Allow station mode SAE to be implemented in user space
SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: Allow user space to specify non-IEs to SAE Authentication
SAE extends Authentication frames with fields that are not information
elements. NL80211_ATTR_IE is not suitable for these, so introduce a new
attribute that can be used to specify the fields needed for SAE in
station mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
[change to verify that SAE is only used with authenticate command] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 11 Sep 2012 12:34:12 +0000 (14:34 +0200)]
mac80211: track needed RX chains for channel contexts
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 26 Jul 2012 15:24:39 +0000 (17:24 +0200)]
mac80211: use channel contexts
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated] Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 26 Jul 2012 12:55:08 +0000 (14:55 +0200)]
mac80211: track whether to use channel contexts
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Tue, 26 Jun 2012 12:37:16 +0000 (14:37 +0200)]
mac80211: introduce channel context skeleton code
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: wipe out the status of the SCD when we disable a queue
When we disable a queue, we don't want the SCD to remember anything
about this queue (what packet was transmitted but not acked, what
packed was acked etc...).
Wipe out all this data in its SRAM.
Constify the arguments to iwl_write_targ_mem_dwords on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 5 Sep 2012 20:34:44 +0000 (22:34 +0200)]
iwlwifi: make data frame tracing optional
When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.
Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.
As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 26 Sep 2012 11:32:13 +0000 (13:32 +0200)]
iwlwifi: improve oversized command warning
When warning about a command that is too large,
print out the command name/ID to help figure
out which place is attempting to send a command
that is too large.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bluetooth: Zero bredr pointer when chan is deleted
If BREDR L2CAP chan is deleted and this chan is the channel through
which High Speed traffic is routed to AMP then zero pointer to
the chan in amp_mgr to prevent accessing it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Gustavo Padovan [Fri, 12 Oct 2012 11:35:23 +0000 (19:35 +0800)]
Bluetooth: Move bt_accept_enqueue() to l2cap_sock.c
This is part of the move the parent socket usage to l2cap_sock.c
The change is safe when it comes to locking, bt_accept_enqueue() is still
protected by the parent socket lock inside the
l2cap_sock_new_connection_cb() code.
Linus Torvalds [Sun, 14 Oct 2012 21:39:05 +0000 (14:39 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Linus Torvalds [Sun, 14 Oct 2012 20:39:34 +0000 (13:39 -0700)]
Merge branch 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Matt Fleming [Fri, 12 Oct 2012 10:19:59 +0000 (11:19 +0100)]
x86, boot: Explicitly include autoconf.h for hostprogs
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de22 ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Oct 2012 00:18:53 +0000 (17:18 -0700)]
Merge branch 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
Linus Torvalds [Sat, 13 Oct 2012 20:28:32 +0000 (13:28 -0700)]
Merge tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
"The patches contained herein do the following:
(1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI. I checked
this with Paul Mackerras before I created the patch and he suggested some
extra bits to unexport.
(2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
applicable, and remove from the UAPI that part of linux/fs.h that was the
reason for linux/blk_types.h being exported in the first place. I
discussed this with Jens Axboe before creating the patch.
(3) The big patch of the series to disintegrate include/linux/*.h as a unit.
This could be split up, though there would be collisions in moving stuff
between the two Kbuild files when the parts are merged as that file is
sorted alphabetically rather than being grouped by subsystem.
Of this set of headers, 17 files have changed in the UAPI exported region
since the 4th and only 8 since the 9th so there isn't much change in this
area - as one might expect.
It should be pretty obvious and straightforward if it does come to fixing
up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
to the same file in the include/uapi/linux/ directory.
If a new file appears then things get a bit more complicated as the
"headers +=" line has to move to include/uapi/linux/Kbuild. Only one new
file has appeared since the 9th and I judge this type of event relatively
unlikely.
(4) A patch to disintegrate include/linux/byteorder/*.h as a unit.
Signed-off-by: David Howells <dhowells@redhat.com>"
* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
Linus Torvalds [Sat, 13 Oct 2012 20:26:39 +0000 (13:26 -0700)]
Merge tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers
Pull spi UAPI disintegration from David Howells:
"This is to complete part of the Userspace API (UAPI) disintegration
for which the preparatory patches were pulled recently. After these
patches, userspace headers will be segregated into:
include/uapi/linux/.../foo.h
for the userspace interface stuff, and:
include/linux/.../foo.h
for the strictly kernel internal stuff.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>"
* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/spi
Linus Torvalds [Sat, 13 Oct 2012 20:23:39 +0000 (13:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace compile fixes from Eric W Biederman:
"This tree contains three trivial fixes. One compiler warning, one
thinko fix, and one build fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
Linus Torvalds [Sat, 13 Oct 2012 20:22:01 +0000 (13:22 -0700)]
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
Russell King [Fri, 12 Oct 2012 13:20:52 +0000 (14:20 +0100)]
ARM: config: make sure that platforms are ordered by option string
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
David Howells [Sat, 13 Oct 2012 09:46:48 +0000 (10:46 +0100)]
UAPI: (Scripted) Disintegrate include/linux
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
David Howells [Sat, 13 Oct 2012 09:45:06 +0000 (10:45 +0100)]
UAPI: Unexport linux/blk_types.h
It seems that was linux/blk_types.h incorrectly exported to fix up some missing
bits required by the exported parts of linux/fs.h (READ, WRITE, READA, etc.).
So unexport linux/blk_types.h and unexport the relevant bits of linux/fs.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jens Axboe <jaxboe@fusionio.com>
cc: Tejun Heo <tj@kernel.org>
cc: Al Viro <viro@ZenIV.linux.org.uk>
Jonas Bonn [Sat, 13 Oct 2012 05:38:37 +0000 (07:38 +0200)]
Merge tag 'disintegrate-openrisc-20121009' of git://git.infradead.org/users/dhowells/linux-headers
UAPI Disintegration 2012-10-09
* tag 'disintegrate-openrisc-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate arch/openrisc/include/asm
Linus Torvalds [Sat, 13 Oct 2012 02:29:00 +0000 (11:29 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM bugfixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: Propagate error from tpm_transmit to fix a timeout hang
driver/char/tpm: fix regression causesd by ppi
Linus Torvalds [Sat, 13 Oct 2012 02:27:59 +0000 (11:27 +0900)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Linus Torvalds [Sat, 13 Oct 2012 02:25:41 +0000 (11:25 +0900)]
Merge tag 'for-3.7' of git://openrisc.net/jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes."
* tag 'for-3.7' of git://openrisc.net/jonas/linux:
openrisc: mask interrupts in irq_mask_ack function
openrisc: fix typos in comments and warnings
openrisc: PIC should act on domain-local irqs
openrisc: Make cpu_relax() invoke barrier()
audit: define AUDIT_ARCH_OPENRISC
openrisc: delay: fix handling of counter overflow
openrisc: delay: fix loops calculation for __const_udelay
Linus Torvalds [Sat, 13 Oct 2012 02:20:04 +0000 (11:20 +0900)]
Merge tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 uapi disintegration from Catalin Marinas:
"UAPI headers for arm64 together with some clean-up to make it
possible:
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers"
* tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
UAPI: (Scripted) Disintegrate arch/arm64/include/asm
arm64: Do not export the compat-specific definitions to the user
arm64: Do not include asm/unistd32.h in asm/unistd.h
arm64: Remove unused definitions from asm/unistd32.h
Linus Torvalds [Sat, 13 Oct 2012 02:16:58 +0000 (11:16 +0900)]
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
Linus Torvalds [Sat, 13 Oct 2012 01:57:57 +0000 (10:57 +0900)]
Merge tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Remove the power-of-2 block size constraint on discards in dm thin
provisioning and factor the bio_prison code out into a separate module
(for sharing with the forthcoming cache target).
Use struct bio's front_pad to eliminate the use of one separate
mempool by bio-based devices.
A few other tiny clean-ups."
* tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: store dm_target_io in bio front_pad
dm thin: move bio_prison code to separate module
dm thin: prepare to separate bio_prison code
dm thin: support discard with non power of two block size
dm persistent data: convert to use le32_add_cpu
dm: use ACCESS_ONCE for sysfs values
dm bufio: use list_move
dm mpath: fix check for null mpio in end_io fn
projects / linux-beck.git / log