Hans Verkuil [Fri, 15 Feb 2013 18:00:20 +0000 (15:00 -0300)]
[media] s5p-tv: remove the dv_preset API from hdmiphy
The dv_preset API is deprecated and is replaced by the much improved dv_timings
API. Remove the dv_preset support from this driver as this will allow us to
remove the dv_preset API altogether (s5p-tv being the last user of this code).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 15 Feb 2013 17:59:48 +0000 (14:59 -0300)]
[media] s5p-tv: remove the dv_preset API from hdmi
The dv_preset API is deprecated and is replaced by the much improved dv_timings
API. Remove the dv_preset support from this driver as this will allow us to
remove the dv_preset API altogether (s5p-tv being the last user of this code).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 4 Mar 2013 12:32:00 +0000 (09:32 -0300)]
[media] s5p-tv: remove dv_preset support from mixer_video
The dv_preset API is deprecated and is replaced by the much improved dv_timings
API. Remove the dv_preset support from this driver as this will allow us to
remove the dv_preset API altogether (s5p-tv being the last user of this code).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 4 Mar 2013 12:28:57 +0000 (09:28 -0300)]
[media] s5p-tv: add dv_timings support for hdmiphy
This just adds dv_timings support without modifying existing dv_preset
support, although I had to refactor a little bit in order to share
hdmiphy_find_conf() between the preset and timings code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Wed, 20 Mar 2013 04:28:27 +0000 (01:28 -0300)]
[media] davinci: vpif: Fix module build for capture and display
export the symbols which are used by two modules vpif_capture and
vpif_display. renamed "ch_params" to "vpif_ch_params" so as to avoid
name collision.
This patch fixes following error:
ERROR: "ch_params" [drivers/media/platform/davinci/vpif_display.ko] undefined!
ERROR: "vpif_ch_params_count" [drivers/media/platform/davinci/vpif_display.ko] undefined!
ERROR: "vpif_base" [drivers/media/platform/davinci/vpif_display.ko] undefined!
ERROR: "ch_params" [drivers/media/platform/davinci/vpif_capture.ko] undefined!
ERROR: "vpif_ch_params_count" [drivers/media/platform/davinci/vpif_capture.ko] undefined!
ERROR: "vpif_base" [drivers/media/platform/davinci/vpif_capture.ko] undefined!
make[1]: *** [__modpost] Error 1
Antti Palosaari [Sun, 10 Mar 2013 00:10:14 +0000 (21:10 -0300)]
[media] it913x: fix pid filter
I just made commit: "dvb_usb_v2: rework USB streaming logic" that
breaks that driver PID filter.
it913x driver checks use of PID filter directly from DVB USB v2 core
internal variable "adap->pid_filtering" and stores it to own state.
Calling order of .pid_filter_ctrl() and .pid_filter() was changed
and due to that state was updated too late. Update state earlier.
TODO: checking PID filter usage from DVB USB v2 is not very good idea
as PID filter callbacks are called only when PID filter is enabled.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Sat, 9 Mar 2013 19:10:55 +0000 (16:10 -0300)]
[media] dvb_usb_v2: rework USB streaming logic
Control flow order changed a little bit. HW PID filter is now
disabled also when streaming is stopped - earlier it was just
set only when streaming was started.
Control flow is now:
* set streaming status bit
* submit USB streaming packets
* enable HW PID filter
* ask device to start streaming
* N x add PID to device HW PID filter
... streaming video ...
* N x remove PID from device HW PID filter
* ask device to stop streaming
* disable HW PID filter
* kill USB streaming packets
* clear streaming status bit
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Sat, 9 Mar 2013 03:16:32 +0000 (00:16 -0300)]
[media] dvb_usb_v2: replace Kernel userspace lock with wait queue
There was sync mutex which was held over userspace. That is very
wrong and could cause deadlock if different userspace process is
used to "unlock". Wait queue seems to be correct solution for
that kind of synchronizing issue so use it instead.
lock debug gives following bug report:
================================================
[ BUG: lock held when returning to user space! ]
3.9.0-rc1+ #38 Tainted: G O
------------------------------------------------
tzap/4614 is leaving the kernel with locks still held!
1 lock held by tzap/4614:
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 22 Mar 2013 12:54:00 +0000 (09:54 -0300)]
[media] em28xx: tuner setup is broken after algo_data change
Commit aab3125c43d8fecc7134e5f1e729fabf4dd196da broke em28xx. I traced
this eventually to the change in what algo_data points to. This pointer
is also passed to em28xx_tuner_callback() through several hidden tuner
layers (yuck!) and that callback was not updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As complained by gcc:
drivers/media/usb/gspca/m5602/m5602_ov7660.c: In function 'ov7660_init':
drivers/media/usb/gspca/m5602/m5602_ov7660.c:99:9: warning: variable 'err' set but not used [-Wunused-but-set-variable]
It should be noticed that the original error code was crappy, as it wasn't
returning any error if sensor init fails.
Fix it by returning an error if the sensor can't be initialized.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 8f3741e accidentally broke the CNR estimation. It should
be calculated as "a + b - c". However, previously, the subtraction
by c only occurred if SNR would be positive, due to a bad binding
to DVBv3 API.
This also fixes the following warning:
drivers/media/dvb-frontends/drxk_hard.c:2556:6: warning: variable 'c' set but not used [-Wunused-but-set-variable]
Those are demodulator init tables according to used tuner tuner
config. af9033 demod driver does those inits currently and due
to that these duplicate inits could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Thu, 7 Mar 2013 22:22:52 +0000 (19:22 -0300)]
[media] af9035: change dual mode boolean to bit field
For some reason there seems to be value 0x03 in eeprom for dual mode
(and 0x00 for single mode). Boolean is not always 1 bit wide - it
could be 8 bit wide too. Storing number 0x03 to boolean causes driver
to thing there is 4 tuners in some cases :o
Add also some comments regarding to eeprom.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Federico Fuga [Fri, 24 Aug 2012 14:54:11 +0000 (11:54 -0300)]
[media] Corrected Oops on omap_vout when no manager is connected
If no manager is connected to the vout device, the omapvid_init() function
fails. No error condition is checked, and the device is started. Later on,
when irq is serviced, a NULL pointer dereference occurs.
Also, the isr routine must be registered only if no error occurs, otherwise
the isr triggers without the proper setup, and the kernel oops again.
To prevent this, the error condition is checked, and the streamon function
exits with error. Also the isr registration call is moved after the setup
procedure is completed.
Dmitri Belimov [Wed, 13 Mar 2013 03:23:36 +0000 (00:23 -0300)]
[media] xc5000: fix incorrect debug printnk
I found very small bug in xc5000 source. When set option debug=1 and
listen a radio we see in dmesg xc5000: xc_SetTVStandard()
Standard = M/N-NTSC/PAL-BTSC at all times. However, it should be, instead
"FM Radio-INPUT1_MONO".
That happens because xc5000_set_radio_freq() gets the correct value for
VideoMode and AudioMode for radio and calls xc_SetTVStandard() where name
of standard comes from the incorrect place priv->video_standard.
This incorrect debug message makes debugging a little difficult.
Paul Bolle [Mon, 11 Mar 2013 21:30:03 +0000 (18:30 -0300)]
[media] soc_camera: remove two outdated selects
Release v2.6.30 removed the MT9M001_PCA9536_SWITCH and
MT9V022_PCA9536_SWITCH Kconfig symbols, in commits 36034dc325ecab63c8cfb992fbf9a1a8e94738a2 ("V4L/DVB (11032): mt9m001:
allow setting of bus width from board code") and e958e27adeade7fa085dd396a8a0dfaef7e338c1 ("V4L/DVB (11033): mt9v022:
allow setting of bus width from board code").
These two commits removed all gpio related code from these two drivers.
But they skipped removing their two selects of GPIO_PCA953X. Remove
these now as they are outdated. Their dependencies can never evaluate to
true anyhow.
Sachin Kamat [Mon, 4 Mar 2013 08:15:21 +0000 (05:15 -0300)]
[media] soc_camera/sh_mobile_csi2: Convert to devm_ioremap_resource()
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Sachin Kamat [Mon, 4 Mar 2013 08:15:20 +0000 (05:15 -0300)]
[media] soc_camera/sh_mobile_ceu_camera: Convert to devm_ioremap_resource()
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
[media] mt9v022 driver: send valid HORIZONTAL_BLANKING values to mt9v024 soc camera
This patch fixes the issue that appears when mt9v024 camera is used with the
mt9v022 soc camera driver. The minimum total row time is 690 columns
(horizontal width + horizontal blanking). The minimum horizontal
blanking is 61. Thus, when the window width is set below 627, horizontal blanking must
be increased. For the mt9v024 camera the values above are correct and
for the mt9v022 camera the correct values are in the existing kernel driver.
[media] mt9m111: fix Oops - initialise context before dereferencing
A recent commit "[media] soc-camera: Push probe-time power management to
drivers" causes an Oops during mt9m111 driver probing because its .ctx
private data field is now dereferenced before it is initialised. Fix this
by initialising the field earlier.
Reported-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] soc-camera: mt9m111: Fix auto-exposure control
Commit f9bd5843658e18a7097fc7258c60fb840109eaa8 changed V4L2_CID_EXPOSURE_AUTO
from boolean to enum, and commit af8425c54beb3c32cbb503a379132b3975535289
changed the creation of this control into a menu for the mt9m111. However,
mt9m111_set_autoexposure() is still interpreting the value set for this control
as a boolean, which also conflicts with the default value of this control set to
V4L2_EXPOSURE_AUTO (0).
This patch makes mt9m111_set_autoexposure() interpret the value set for
V4L2_CID_EXPOSURE_AUTO as defined by enum v4l2_exposure_auto_type.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Paul Bolle [Mon, 11 Mar 2013 14:31:39 +0000 (11:31 -0300)]
[media] ts2020: use customise option correctly
The Kconfig entry for "TS2020 based tuners" defaults to modular if
DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, so we are in line with all the similar entries in this file.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manjunath Hadli [Fri, 8 Mar 2013 07:13:35 +0000 (04:13 -0300)]
[media] media: tvp514x: enable TVP514X for media controller based usage
add support for TVP514x as a media entity and support for
pad operations. The decoder supports 1 output pad.
The default format code was V4L2_MBUS_FMT_YUYV10_2X10
changed it to V4L2_MBUS_FMT_UYVY8_2X8.
Manjunath Hadli [Thu, 7 Feb 2013 16:48:51 +0000 (13:48 -0300)]
[media] media: add support for decoder as one of media entity types
A lot of SOCs including Texas Instruments Davinci family mainly use
video decoders as input devices. This patch adds a flag
'MEDIA_ENT_T_V4L2_SUBDEV_DECODER' media entity type for decoder's.
Along side updates the documentation for this media entity type.
Lad, Prabhakar [Mon, 18 Feb 2013 10:56:41 +0000 (07:56 -0300)]
[media] media: ths7353: add support for ths7353 video amplifier
The patch adds support for THS7353 video amplifier.
The the THS7353 amplifier is very much similar to the
existing THS7303 video amplifier driver.
This patch appropriately makes changes to the existing
ths7303 driver and adds support for the THS7353.
This patch also adds V4L2_IDENT_THS7353 for the THS7353
chip and appropriate changes to Kconfig file for building.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 1 Mar 2013 18:44:20 +0000 (15:44 -0300)]
[media] videobuf2: add gfp_flags
Some drivers have special memory requirements for their buffers, usually
related to DMA (e.g. GFP_DMA or __GFP_DMA32). Make it possible to specify
additional GFP flags for those buffers by adding a gfp_flags field to
vb2_queue.
Note that this field will be replaced in the future with a different
mechanism, but that is still work in progress and we need this feature
now so we won't be able to convert drivers with such requirements to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Federico Vaga <federico.vaga@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVBv3 signal strength indicator is bogus: it doesn't range
from 0 to 65535 as it would be expected. Also, 0 means the max
signal strength.
Now that a better way to estimate it was added, use the new
way.
[media] drxk: use a better calculus for RF strength
The AZ6007 driver released by Terratec has a better way to
estimate the signal strength, at CtrlSigStrength(). Port it
to the driver.
It should be noticed that there are two parameters there that
are tuner-specific.
projects / linux-beck.git / log