crypto: s5p-sss - Fix missed interrupts when working with 8 kB blocks
The tcrypt testing module on Exynos5422-based Odroid XU3/4 board failed on
testing 8 kB size blocks:
$ sudo modprobe tcrypt sec=1 mode=500
testing speed of async ecb(aes) (ecb-aes-s5p) encryption
test 0 (128 bit key, 16 byte blocks): 21971 operations in 1 seconds (351536 bytes)
test 1 (128 bit key, 64 byte blocks): 21731 operations in 1 seconds (1390784 bytes)
test 2 (128 bit key, 256 byte blocks): 21932 operations in 1 seconds (5614592 bytes)
test 3 (128 bit key, 1024 byte blocks): 21685 operations in 1 seconds (22205440 bytes)
test 4 (128 bit key, 8192 byte blocks):
This was caused by a race issue of missed BRDMA_DONE ("Block cipher
Receiving DMA") interrupt. Device starts processing the data in DMA mode
immediately after setting length of DMA block: receiving (FCBRDMAL) or
transmitting (FCBTDMAL). The driver sets these lengths from interrupt
handler through s5p_set_dma_indata() function (or xxx_setdata()).
However the interrupt handler was first dealing with receive buffer
(dma-unmap old, dma-map new, set receive block length which starts the
operation), then with transmit buffer and finally was clearing pending
interrupts (FCINTPEND). Because of the time window between setting
receive buffer length and clearing pending interrupts, the operation on
receive buffer could end already and driver would miss new interrupt.
User manual for Exynos5422 confirms in example code that setting DMA
block lengths should be the last operation.
The tcrypt hang could be also observed in following blocked-task dmesg:
INFO: task modprobe:258 blocked for more than 120 seconds.
Not tainted 4.6.0-rc4-next-20160419-00005-g9eac8b7b7753-dirty #42
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c06b09d8 0 258 256 0x00000000
[<c06b09d8>] (__schedule) from [<c06b0f24>] (schedule+0x40/0xac)
[<c06b0f24>] (schedule) from [<c06b49f8>] (schedule_timeout+0x124/0x178)
[<c06b49f8>] (schedule_timeout) from [<c06b17fc>] (wait_for_common+0xb8/0x144)
[<c06b17fc>] (wait_for_common) from [<bf0013b8>] (test_acipher_speed+0x49c/0x740 [tcrypt])
[<bf0013b8>] (test_acipher_speed [tcrypt]) from [<bf003e8c>] (do_test+0x2240/0x30ec [tcrypt])
[<bf003e8c>] (do_test [tcrypt]) from [<bf008048>] (tcrypt_mod_init+0x48/0xa4 [tcrypt])
[<bf008048>] (tcrypt_mod_init [tcrypt]) from [<c010177c>] (do_one_initcall+0x3c/0x16c)
[<c010177c>] (do_one_initcall) from [<c0191ff0>] (do_init_module+0x5c/0x1ac)
[<c0191ff0>] (do_init_module) from [<c0185610>] (load_module+0x1a30/0x1d08)
[<c0185610>] (load_module) from [<c0185ab0>] (SyS_finit_module+0x8c/0x98)
[<c0185ab0>] (SyS_finit_module) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Fixes: a49e490c7a8a ("crypto: s5p-sss - add S5PV210 advanced crypto engine support") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dan Carpenter [Fri, 22 Apr 2016 10:01:39 +0000 (13:01 +0300)]
crypto: mxc-scc - fix unwinding in mxc_scc_crypto_register()
There are two issues here:
1) We need to decrement "i" otherwise we unregister something that was
not successfully registered.
2) The original code did not unregister the first element in the array
where i is zero.
Fixes: d293b640ebd5 ('crypto: mxc-scc - add basic driver for the MXC SCC') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dan Carpenter [Fri, 22 Apr 2016 09:56:31 +0000 (12:56 +0300)]
crypto: mxc-scc - signedness bugs in mxc_scc_ablkcipher_req_init()
->src_nents and ->dst_nents are unsigned so they can't be less than
zero. I fixed this by introducing a temporary "nents" variable.
Fixes: d293b640ebd5 ('crypto: mxc-scc - add basic driver for the MXC SCC') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When looking for available engines, the variable "engine" is
assigned to "&cesa->engines[i]" at the beginning of the for loop. Replacing
next occurences of "&cesa->engines[i]" by "engine" and in order to improve
readability.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Beside regular feed control interrupt, the driver requires also hash
interrupt for older SoCs (samsung,s5pv210-secss). However after
requesting it, the interrupt handler isn't doing anything with it, not
even clearing the hash interrupt bit.
Driver does not provide hash functions so it is safe to remove the hash
interrupt related code and to not require the interrupt in Device Tree.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: s5p-sss - Fix use after free of copied input buffer in error path
The driver makes copies of memory (input or output scatterlists) if they
are not aligned. In s5p_aes_crypt_start() error path (on unsuccessful
initialization of output scatterlist), if input scatterlist was not
aligned, the driver first freed copied input memory and then unmapped it
from the device, instead of doing otherwise (unmap and then free).
This was wrong in two ways:
1. Freed pages were still mapped to the device.
2. The dma_unmap_sg() iterated over freed scatterlist structure.
The call to s5p_free_sg_cpy() in this error path is not needed because
the copied scatterlists will be freed by s5p_aes_complete().
Fixes: 9e4a1100a445 ("crypto: s5p-sss - Handle unaligned buffers") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Gary R Hook [Mon, 18 Apr 2016 14:21:44 +0000 (09:21 -0500)]
crypto: ccp - Register the CCP as a DMA resource
The CCP has the ability to provide DMA services to the
kernel using pass-through mode of the device. Register
these services as general purpose DMA channels.
Changes since v2:
- Add a Signed-off-by
Changes since v1:
- Allocate memory for a string in ccp_dmaengine_register
- Ensure register/unregister calls are properly ordered
- Verified all changed files are listed in the diffstat
- Undo some superfluous changes
- Added a cc:
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch integrates the ppc4xx-rng driver into the existing
crypto4xx. This is because the true random number generator
is controlled and part of the security core.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tadeusz Struk [Fri, 15 Apr 2016 17:54:07 +0000 (10:54 -0700)]
crypto: qat - fix section mismatch warning
Fix Section mismatch warinig in adf_exit_vf_wq()
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Michal Hocko [Thu, 14 Apr 2016 08:51:42 +0000 (10:51 +0200)]
crypto: lzo - get rid of superfluous __GFP_REPEAT
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
lzo_init uses __GFP_REPEAT to allocate LZO1X_MEM_COMPRESS 16K. This is
order 3 allocation request and __GFP_REPEAT is ignored for this size
as well as all <= PAGE_ALLOC_COSTLY requests.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-crypto@vger.kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tadeusz Struk [Wed, 6 Apr 2016 18:01:54 +0000 (11:01 -0700)]
crypto: qat - adf_dev_stop should not be called in atomic context
VFs call adf_dev_stop() from a PF to VF interrupt bottom half.
This causes an oops "scheduling while atomic", because it tries
to acquire a mutex to un-register crypto algorithms.
This patch fixes the issue by calling adf_dev_stop() asynchronously.
Changes in v2:
- change kthread to a work queue.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Direct include of rwlock_types.h breaks RT, use spinlock_types.h instead.
Fixes: 553d2374db0b crypto: ccp - Support for multiple CCPs Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stephan Mueller [Mon, 28 Mar 2016 14:47:55 +0000 (16:47 +0200)]
crypto: drbg - set HMAC key only when altered
The HMAC implementation allows setting the HMAC key independently from
the hashing operation. Therefore, the key only needs to be set when a
new key is generated.
This patch increases the speed of the HMAC DRBG by at least 35% depending
on the use case.
The patch is fully CAVS tested.
Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Corentin LABBE [Wed, 23 Mar 2016 15:11:24 +0000 (16:11 +0100)]
crypto: sun4i-ss - Replace spinlock_bh by spin_lock_irq{save|restore}
The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.
The exact purpose of the len extension isn't clear to me, but due to
its form, I suspect that it's a leftover somehow accounting for leading
zero bytes within the most significant output limb.
Note however that without that len adjustement, the total number of bytes
ever processed by the inner loop equals nbytes and thus, the last output
limb gets written at this point. Thus the net effect of the len adjustement
cited above is just to keep the inner loop running for some more
iterations, namely < BYTES_PER_MPI_LIMB ones, reading some extra bytes from
beyond the last SGE's buffer and discarding them afterwards.
Fix this issue by purging the extension of len beyond the last input SGE's
buffer length.
Nicolai Stange [Tue, 22 Mar 2016 12:18:07 +0000 (13:18 +0100)]
lib/mpi: mpi_read_raw_from_sgl(): sanitize meaning of indices
Within the byte reading loop in mpi_read_raw_sgl(), there are two
housekeeping indices used, z and x.
At all times, the index z represents the number of output bytes covered
by the input SGEs for which processing has completed so far. This includes
any leading zero bytes within the most significant limb.
The index x changes its meaning after the first outer loop's iteration
though: while processing the first input SGE, it represents
"number of leading zero bytes in most significant output limb" +
"current position within current SGE"
For the remaining SGEs OTOH, x corresponds just to
"current position within current SGE"
After all, it is only the sum of z and x that has any meaning for the
output buffer and thus, the
"number of leading zero bytes in most significant output limb"
part can be moved away from x into z from the beginning, opening up the
opportunity for cleaner code.
Before the outer loop iterating over the SGEs, don't initialize z with
zero, but with the number of leading zero bytes in the most significant
output limb. For the inner loop iterating over a single SGE's bytes,
get rid of the buf_shift offset to x' bounds and let x run from zero to
sg->length - 1.
Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
However, count_leading_zeros() takes an unsigned long and thus,
the u8 gets promoted to an unsigned long.
Thus, the above doesn't subtract the number of leading zeros in the most
significant nonzero input byte from nbits, but the number of leading
zeros of the most significant nonzero input byte promoted to unsigned long,
i.e. BITS_PER_LONG - 8 too many.
/* sg contains nothing but zeros here */
ents--;
lzeros = 0;
}
Later on, the total number of trailing nonzero bytes is calculated by
subtracting the number of leading zero bytes from the total number of input
bytes:
nbytes -= lzeros;
However, since lzeros gets reset to zero for each completely zero leading
sg in the loop above, it doesn't include those.
Besides wasting resources by allocating a too large output buffer,
this mistake propagates into the calculation of x, the number of
leading zeros within the most significant output limb:
x = BYTES_PER_MPI_LIMB - nbytes % BYTES_PER_MPI_LIMB;
What's more, the low order bytes of the output, equal in number to the
extra bytes in nbytes, are left uninitialized.
Fix this by adjusting nbytes for each completely zero leading scatterlist
entry.
Nicolai Stange [Tue, 22 Mar 2016 12:12:43 +0000 (13:12 +0100)]
lib/mpi: mpi_read_raw_from_sgl(): replace len argument by nbytes
Currently, the nbytes local variable is calculated from the len argument
as follows:
... mpi_read_raw_from_sgl(..., unsigned int len)
{
unsigned nbytes;
...
if (!ents)
nbytes = 0;
else
nbytes = len - lzeros;
...
}
Given that nbytes is derived from len in a trivial way and that the len
argument is shadowed by a local len variable in several loops, this is just
confusing.
Rename the len argument to nbytes and get rid of the nbytes local variable.
Do the nbytes calculation in place.
Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nicolai Stange [Tue, 22 Mar 2016 12:12:42 +0000 (13:12 +0100)]
lib/mpi: mpi_read_buffer(): fix buffer overflow
Currently, mpi_read_buffer() writes full limbs to the output buffer
and moves memory around to purge leading zero limbs afterwards.
However, with
commit 9cbe21d8f89d ("lib/mpi: only require buffers as big as needed for
the integer")
the caller is only required to provide a buffer large enough to hold the
result without the leading zeros.
This might result in a buffer overflow for small MP numbers with leading
zeros.
Fix this by coping the result to its final destination within the output
buffer and not copying the leading zeros at all.
Fixes: 9cbe21d8f89d ("lib/mpi: only require buffers as big as needed for
the integer") Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: s5p-sss - Sort the headers to improve readability
Sort the headers alphabetically to improve readability and to spot
duplications easier.
Suggested-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During crypto selftests on Odroid XU3 (Exynos5422) some of the
algorithms failed because of passing AES-block unaligned source and
destination buffers:
alg: skcipher: encryption failed on chunk test 1 for ecb-aes-s5p: ret=22
Handle such case by copying the buffers to a new aligned and contiguous
space.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove unneeded inclusion of delay.h and get rid of indentation from
labels.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dan Carpenter [Mon, 21 Mar 2016 09:03:43 +0000 (12:03 +0300)]
crypto: marvell/cesa - remove unneeded condition
creq->cache[] is an array inside the struct, it's not a pointer and it
can't be NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Colin Ian King [Fri, 18 Mar 2016 15:51:31 +0000 (15:51 +0000)]
PKCS#7: fix missing break on OID_sha224 case
The OID_sha224 case is missing a break and it falls through
to the -ENOPKG error default. Since HASH_ALGO_SHA224 seems
to be supported, this looks like an unintentional missing break.
Fixes: 07f081fb5057 ("PKCS#7: Add OIDs for sha224, sha284 and sha512 hash algos and use them") Cc: <stable@vger.kernel.org> # 4.2+ Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: n2 - Remove return statement from void function
Return statement at the end of a void function is useless.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
identifier f;
expression e;
@@
void f(...) {
<...
- return
e;
...>
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Get some build coverage of S5P/Exynos AES H/W acceleration driver.
Driver uses DMA and devm_ioremap_resource() so add DMA and IOMEM
dependencies for the compile testing.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Get some build coverage of Exynos H/W random number generator
driver. Driver uses devm_ioremap_resource() so add IOMEM dependency for
the compile testing.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hwrng: exynos - Disable runtime PM on driver unbind
Driver enabled runtime PM but did not revert this on removal. Re-binding
of a device triggered warning:
exynos-rng 10830400.rng: Unbalanced pm_runtime_enable!
Fixes: b329669ea0b5 ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hwrng: exynos - Disable runtime PM on probe failure
Add proper error path (for disabling runtime PM) when registering of
hwrng fails.
Fixes: b329669ea0b5 ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hwrng: exynos - Fix unbalanced PM runtime put on timeout error path
In case of timeout during read operation, the exit path lacked PM
runtime put. This could lead to unbalanced runtime PM usage counter thus
leaving the device in an active state.
Fixes: d7fd6075a205 ("hwrng: exynos - Add timeout for waiting on init done") Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver uses pm_runtime_put_noidle() after initialization so the
device might remain in active state if the core does not read from it
(the read callback contains regular runtime put). The put_noidle() was
chosen probably to avoid unneeded suspend and resume cycle after the
initialization.
However for this purpose autosuspend is enabled so it is safe to runtime
put just after the initialization.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tadeusz Struk [Fri, 11 Mar 2016 19:50:33 +0000 (11:50 -0800)]
crypto: af_alg - add async support to algif_aead
Following the async change for algif_skcipher
this patch adds similar async read to algif_aead.
changes in v3:
- add call to aead_reset_ctx directly from aead_put_sgl instead of calling
them separatelly one after the other
- remove wait from aead_sock_destruct function as it is not needed
when sock_hold is used
changes in v2:
- change internal data structures from fixed size arrays, limited to
RSGL_MAX_ENTRIES, to linked list model with no artificial limitation.
- use sock_kmalloc instead of kmalloc for memory allocation
- use sock_hold instead of separate atomic ctr to wait for outstanding
request
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 3 Apr 2016 04:37:15 +0000 (12:37 +0800)]
sunrpc: Fix skcipher/shash conversion
The skcpiher/shash conversion introduced a number of bugs in the
sunrpc code:
1) Missing calls to skcipher_request_set_tfm lead to crashes.
2) The allocation size of shash_desc is too small which leads to
memory corruption.
Fixes: 3b5cf20cf439 ("sunrpc: Use skcipher and ahash/shash") Reported-by: J. Bruce Fields <bfields@fieldses.org> Tested-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
you noted during the original nohz pull request, plus there's also
misc fixes:
- fix liblockdep build bug
- fix uapi header build bug
- print more lockdep hash collision info to help debug recent reports
of hash collisions
- update MAINTAINERS email address"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Update my email address
locking/lockdep: Print chain_key collision information
uapi/linux/stddef.h: Provide __always_inline to userspace headers
tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
locking/atomic, sched: Unexport fetch_or()
timers/nohz: Convert tick dependency mask to atomic_t
locking/atomic: Introduce atomic_fetch_or()
Commit 840f5b0572ea ("media: au0828 disable tuner to demod link in
au0828_media_device_register()") removed all uses of the 'dtv_demod',
but left the variable itself around.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This lot contains:
- Some fixups for the fallout of the topology consolidation which
unearthed AMD/Intel inconsistencies
- Documentation for the x86 topology management
- Support for AMD advanced power management bits
- Two simple cleanups removing duplicated code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add advanced power management bits
x86/thread_info: Merge two !__ASSEMBLY__ sections
x86/cpufreq: Remove duplicated TDP MSR macro definitions
x86/Documentation: Start documenting x86 topology
x86/cpu: Get rid of compute_unit_id
perf/x86/amd: Cleanup Fam10h NB event constraints
x86/topology: Fix AMD core count
Merge tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc
Pull remoteproc fix from Bjorn Andersson:
"Fix incorrect error check in the ST remoteproc driver and advertise
the newly created linux-remoteproc mailing list"
* tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc:
MAINTAINERS: Add mailing list for remote processor subsystems
remoteproc: st: fix check of syscon_regmap_lookup_by_phandle() return value
Pull SCSI target fixes from Nicholas Bellinger:
"This includes fixes from HCH for -rc1 configfs default_groups
conversion changes that ended up breaking some iscsi-target
default_groups, along with Sagi's ib_drain_qp() conversion for
iser-target to use the common caller now available to RDMA kernel
consumers in v4.6+ code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: add a new add_wwn_groups fabrics method
target: initialize the nacl base CIT begfore init_nodeacl
target: remove ->fabric_cleanup_nodeacl
iser-target: Use ib_drain_qp
Convert straggling drivers to new six-argument get_user_pages()
Commit d4edcf0d5695 ("mm/gup: Switch all callers of get_user_pages() to
not pass tsk/mm") switched get_user_pages() callers to the simpler model
where they no longer pass in the thread and mm pointer. But since then
we've merged changes to a few drivers that re-introduce use of the old
interface. Let's fix them up.
They continued to work fine (thanks to the truly disgusting macros
introduced in commit cde70140fed8: "mm/gup: Overload get_user_pages()
functions"), but cause unnecessary build noise.
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of const updates for reset ops and a couple fixes to the
newly introduced IPQ4019 clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
clk: qcom: ipq4019: switch remaining defines to enums
clk: qcom: Make reset_control_ops const
clk: tegra: Make reset_control_ops const
clk: sunxi: Make reset_control_ops const
clk: atlas7: Make reset_control_ops const
clk: rockchip: Make reset_control_ops const
clk: mmp: Make reset_control_ops const
clk: mediatek: Make reset_control_ops const
Merge tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fix from Rafael J. Wysocki:
"Just one fix for a nasty boot failure on some systems based on Intel
Skylake that shipped with broken firmware where enabling
hardware-coordinated P-states management (HWP) causes a faulty
interrupt handler in SMM to be invoked and crash the system (Srinivas
Pandruvada)"
* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Request native thermal interrupt handling via _OSC
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
Merge branch 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has a few fixes Dave Sterba had queued up. These are all pretty
small, but since they were tested I decided against waiting for more"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: transaction_kthread() is not freezable
btrfs: cleaner_kthread() doesn't need explicit freeze
btrfs: do not write corrupted metadata blocks to disk
btrfs: csum_tree_block: return proper errno value
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix oops when patching in alternative sequences on big-endian CPUs
- reconcile asm/perf_event.h after merge window fallout with KVM ARM
- defconfig updates
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: updates for 4.6
arm64: perf: Move PMU register related defines to asm/perf_event.h
arm64: opcodes.h: Add arm big-endian config options before including arm header
Merge tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- a fix in ALSA timer core to avoid possible BUG() trigger
- a fix in ALSA timer core 32bit compat layer
- a few HD-audio quirks for ASUS and HP machines
- AMD HD-audio HDMI controller quirks
- fixes of USB-audio double-free at some error paths
- a fix for memory leak in DICE driver at hotunplug"
* tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: timer: Use mod_timer() for rearming the system timer
ALSA: hda - fix front mic problem for a HP desktop
ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
ALSA: dice: fix memory leak when unplugging
ALSA: hda - Apply fix for white noise on Asus N550JV, too
ALSA: hda - Fix white noise on Asus N750JV headphone
ALSA: hda - Asus N750JV external subwoofer fixup
ALSA: timer: fix gparams ioctl compatibility for different architectures
Newer Fedora and OpenSUSE didn't boot with my standard configuration.
It took me some time to figure out why, in fact I had to write a script
to try different config options systematically.
The problem is that something (systemd) in dracut depends on
CONFIG_FHANDLE, which adds open by file handle syscalls.
While it is set in defconfigs it is very easy to miss when updating
older configs because it is not default y.
Make it default y and also depend on EXPERT, as dracut use is likely
widespread.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Richard Weinberger <richard.weinberger@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Zhang [Fri, 1 Apr 2016 21:31:37 +0000 (14:31 -0700)]
mm/page_isolation.c: fix the function comments
Commit fea85cff11de ("mm/page_isolation.c: return last tested pfn rather
than failure indicator") changed the meaning of the return value. Let's
change the function comments as well.
Signed-off-by: Neil Zhang <neilzhang1123@hotmail.com> Cc: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 1 Apr 2016 21:31:34 +0000 (14:31 -0700)]
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
Commit bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using
simpler way") has simplified the check for tasks already enqueued for
the oom reaper by checking tsk->oom_reaper_list != NULL. This check is
not sufficient because the tsk might be the head of the queue without
any other tasks queued and then we would simply lockup looping on the
same task. Fix the condition by checking for the head as well.
Fixes: bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using simpler way") Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lucas Stach [Fri, 1 Apr 2016 21:31:32 +0000 (14:31 -0700)]
mm/page_isolation: fix tracepoint to mirror check function behavior
Page isolation has not failed if the fin pfn extends beyond the end pfn
and test_pages_isolated checks this correctly. Fix the tracepoint to
report the same result as the actual check function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:26 +0000 (14:31 -0700)]
mm/rmap: batched invalidations should use existing api
The recently introduced batched invalidations mechanism uses its own
mechanism for shootdown. However, it does wrong accounting of
interrupts (e.g., inc_irq_stat is called for local invalidations),
trace-points (e.g., TLB_REMOTE_SHOOTDOWN for local invalidations) and
may break some platforms as it bypasses the invalidation mechanisms of
Xen and SGI UV.
This patch reuses the existing TLB flushing mechnaisms instead. We use
NULL as mm to indicate a global invalidation is required.
Fixes 72b252aed506b8 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:23 +0000 (14:31 -0700)]
x86/mm: TLB_REMOTE_SEND_IPI should count pages
TLB_REMOTE_SEND_IPI was recently introduced, but it counts bytes instead
of pages. In addition, it does not report correctly the case in which
flush_tlb_page flushes a page. Fix it to be consistent with other TLB
counters.
Fixes: 5b74283ab251b9d ("x86, mm: trace when an IPI is about to be sent") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is incorrect to use next_node to find a target node, it will return
MAX_NUMNODES or invalid node. This will lead to crash in buddy system
allocation.
Marcin Wojtas [Fri, 1 Apr 2016 13:21:18 +0000 (15:21 +0200)]
net: mvneta: fix changing MTU when using per-cpu processing
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Revert "stmmac: Fix 'eth0: No PHY found' regression"
This reverts commit 88f8b1bb41c6208f81b6a480244533ded7b59493.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Andreas Färber <afaerber@suse.de> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixs a regression raised when test on chips that use
the normal descriptor layout. In fact, no len bits were set for
the TDES1 and no OWN bit inside the TDES0.
Signed-off-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com> Tested-by: Andreas Färber <afaerber@suse.de> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log