Ville Syrjälä [Thu, 16 Oct 2014 18:27:29 +0000 (21:27 +0300)]
drm/i915: Remove high level intel_edp_vdd_{on, off}() from hpd/detect
want_panel_vdd is a bool so it can't cope with interleaving on/off calls
from multiple threads. If we want to make that possible we'd need to
convert want_panel_vdd into a proper ref count. But an easier fix is to
remove the high level vdd on/off calls from detect/hpd code paths and
just rely on the delayed vdd off to avoid needless vdd on<->off ping
pong.
After this change only the encoder enable/disable paths use the high
level functions, which is fine since both the on and off low level edp
vdd calls from intel_dp_aux_ch() happen without dropping pps_mutex in
between and so want_panel_vdd can't change in between.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:27:27 +0000 (21:27 +0300)]
drm/i915: Warn if trying to register eDP on port != B/C on vlv/chv
Only ports B and C have the power sequencer and backlight controls,
so complain if we ever try to register an eDP connector on some other
port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 27 Oct 2014 19:47:52 +0000 (17:47 -0200)]
drm/i915: transform INTEL_OUTPUT_* into an enum
Because I got annoyed that I had to document what values "int
ddi_personality" is supposed to hold.
A good side-effect of this change is that now the compilers can do
some additional checks on our code, which may prevent some bugs in the
future. A bad side-effect of this change is that now the compilers do
some additional checks on our code and complain when a switch
statement doesn't check for all possible values, so we need to add
"default" cases to all those switches. Hopefully, this may help
preventing confusions against DRM_MODE_CONNECTOR_* and
DRM_MODE_ENCODER_*.
I guess that just by looking at the patch, some people will think this
change is not worth its benefits. In this case, I don't really mind
dropping the patch.
Also, there's probably still a few more places where we can
s/int/enum intel_output_type/, but we can change that later, when we
spot the places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Resolve conflict due to reordered patches.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 24 Oct 2014 23:11:11 +0000 (00:11 +0100)]
drm/i915: Remove unnecessary test on the gen in intel_do_mmio_flip()
use_mmio_flip() makes sure we only enable MMIO flips on gen5+. So we
don't need to take into account older devices.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin [Thu, 16 Oct 2014 19:24:42 +0000 (12:24 -0700)]
drm/i915: Abort command parsing for chained batches
libva uses chained batch buffers in a way that the command parser
can't generally handle. Fortunately, libva doesn't need to write
registers from batch buffers in the way that mesa does, so this
patch causes the driver to fall back to non-secure dispatch if
the parser detects a chained batch buffer.
Note: The 2nd hunk to munge the error code of the parser looks a bit
superflous. At least until we have the batch copy code ready and can
run the cmd parser in granting mode. But it isn't since we still need
to let existing libva buffers pass (though not with elevated privs
ofc!).
Testcase: igt/gem_exec_parse/chained-batch Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Add note - this confused me in review and Brad clarified
things (after a few mails ...).] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sonika Jindal [Thu, 23 Oct 2014 14:41:33 +0000 (07:41 -0700)]
drm/i915: Update plane parameters for cursor plane (v2)
This allows the cursor plane to be updated the same way as primary and sprites,
and same set_property handler is used for all of these planes.
v2 (by Matt Roper): Rework to apply to latest di-nightly codebase. The
switch to split check/commit plane programming changed the code
flow enough that the original patch could no longer be applied.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko Ursulin [Fri, 24 Oct 2014 11:42:33 +0000 (12:42 +0100)]
drm/i915: Move flags describing VMA mappings into the VMA
If these flags are on the object level it will be more difficult to allow
for multiple VMAs per object.
v2: Simplification and cleanup after code review comments (Chris Wilson).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Mon, 3 Nov 2014 21:36:06 +0000 (07:36 +1000)]
Merge tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel into drm-next
- suspend/resume/freeze/thaw unification from Imre
- wa list improvements from Mika&Arun
- display pll precomputation from Ander Conselvan, this removed the last
->mode_set callbacks, a big step towards implementing atomic modesets
- more kerneldoc for the interrupt code
- 180 rotation for cursors (Ville&Sonika)
- ULT/ULX feature check macros cleaned up thanks to Damien
- piles and piles of fixes all over, bug team seems to work!
* tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20141024
drm/i915: add comments on what stage a given PM handler is called
drm/i915: unify switcheroo and legacy suspend/resume handlers
drm/i915: add poweroff_late handler
drm/i915: sanitize suspend/resume helper function names
drm/i915: unify S3 and S4 suspend/resume handlers
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
drm/i915: enable output polling during S4 thaw
drm/i915: check for GT faults in all resume handlers and driver load time
drm/i915: remove unused restore_gtt_mappings optimization during suspend
drm/i915: fix S4 suspend while switcheroo state is off
drm/i915: vlv: fix switcheroo/legacy suspend/resume
drm/i915: propagate error from legacy resume handler
drm/i915: unify legacy S3 suspend and S4 freeze handlers
drm/i915: factor out i915_drm_suspend_late
drm/i915: Emit even number of dwords when emitting LRIs
drm/i915: Add rotation support for cursor plane (v5)
drm/i915: Correctly reject invalid flags for wait_ioctl
drm/i915: use macros to assign mmio access functions
drm/i915: only run hsw_power_well_post_enable when really needed
...
Dave Airlie [Tue, 28 Oct 2014 02:37:58 +0000 (12:37 +1000)]
Merge tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel into drm-next
Ok, new attempt, this time around with full ppgtt disabled again.
drm-intel-next-2014-10-03:
- first batch of skl stage 1 enabling
- fixes from Rodrigo to the PSR, fbc and sink crc code
- kerneldoc for the frontbuffer tracking code, runtime pm code and the basic
interrupt enable/disable functions
- smaller stuff all over
drm-intel-next-2014-09-19:
- bunch more i830M fixes from Ville
- full ppgtt now again enabled by default
- more ppgtt fixes from Michel Thierry and Chris Wilson
- plane config work from Gustavo Padovan
- spinlock clarifications
- piles of smaller improvements all over, as usual
* tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel: (114 commits)
Revert "drm/i915: Enable full PPGTT on gen7"
drm/i915: Update DRIVER_DATE to 20141003
drm/i915: Remove the duplicated logic between the two shrink phases
drm/i915: kerneldoc for interrupt enable/disable functions
drm/i915: Use dev_priv instead of dev in irq setup functions
drm/i915: s/pm._irqs_disabled/pm.irqs_enabled/
drm/i915: Clear TX FIFO reset master override bits on chv
drm/i915: Make sure hardware uses the correct swing margin/deemph bits on chv
drm/i915: make sink_crc return -EIO on aux read/write failure
drm/i915: Constify send buffer for intel_dp_aux_ch
drm/i915: De-magic the PSR AUX message
drm/i915: Reinstate error level message for non-simulated gpu hangs
drm/i915: Kerneldoc for intel_runtime_pm.c
drm/i915: Call runtime_pm_disable directly
drm/i915: Move intel_display_set_init_power to intel_runtime_pm.c
drm/i915: Bikeshed rpm functions name a bit.
drm/i915: Extract intel_runtime_pm.c
drm/i915: Remove intel_modeset_suspend_hw
drm/i915: spelling fixes for frontbuffer tracking kerneldoc
drm/i915: Tighting frontbuffer tracking around flips
...
Linus Torvalds [Sun, 26 Oct 2014 18:35:51 +0000 (11:35 -0700)]
Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
Olof Johansson [Sun, 26 Oct 2014 03:44:05 +0000 (20:44 -0700)]
Merge tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Linus Torvalds [Fri, 24 Oct 2014 19:48:47 +0000 (12:48 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This is the first round of fixes and tying up loose ends for MIPS.
- plenty of fixes for build errors in specific obscure configurations
- remove redundant code on the Lantiq platform
- removal of a useless SEAD I2C driver that was causing a build issue
- fix an earlier TLB exeption handler fix to also work on Octeon.
- fix ISA level dependencies in FPU emulator's instruction decoding.
- don't hardcode kernel command line in Octeon software emulator.
- fix an earlier fix for the Loondson 2 clock setting"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: SEAD3: Fix I2C device registration.
MIPS: SEAD3: Nuke PIC32 I2C driver.
MIPS: ftrace: Fix a microMIPS build problem
MIPS: MSP71xx: Fix build error
MIPS: Malta: Do not build the malta-amon.c file if CMP is not enabled
MIPS: Prevent compiler warning from cop2_{save,restore}
MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidle
MIPS: idle: Remove leftover __pastwait symbol and its references
MIPS: Sibyte: Include the swarm subdir to the sb1250 LittleSur builds
MIPS: ptrace.h: Add a missing include
MIPS: ath79: Fix compilation error when CONFIG_PCI is disabled
MIPS: MSP71xx: Remove compilation error when CONFIG_MIPS_MT is present
MIPS: Octeon: Remove special case for simulator command line.
MIPS: tlbex: Properly fix HUGE TLB Refill exception handler
MIPS: loongson2_cpufreq: Fix CPU clock rate setting mismerge
pci: pci-lantiq: remove duplicate check on resource
MIPS: Lasat: Add missing CONFIG_PROC_FS dependency to PICVUE_PROC
MIPS: cp1emu: Fix ISA restrictions for cop1x_op instructions
Linus Torvalds [Fri, 24 Oct 2014 19:48:04 +0000 (12:48 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable 48-bit VA space now that KVM has been fixed, together with a
couple of fixes for pgd allocation alignment and initial memblock
current_limit. There is still a dependency on !ARM_SMMU which needs
to be updated as it uses the page table manipulation macros of the
host kernel
- eBPF fixes following changes/conflicts during the merging window
- Compat types affecting compat_elf_prpsinfo
- Compilation error on UP builds
- ASLR fix when /proc/sys/kernel/randomize_va_space == 0
- DT definitions for CLCD support on ARMv8 model platform
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
arm64: ASLR: Don't randomise text when randomise_va_space == 0
arm64: vexpress: Add CLCD support to the ARMv8 model platform
arm64: Fix compilation error on UP builds
Documentation/arm64/memory.txt: fix typo
net: bpf: arm64: minor fix of type in jited
arm64: bpf: add 'load 64-bit immediate' instruction
arm64: bpf: add 'shift by register' instructions
net: bpf: arm64: address randomize and write protect JIT code
arm64: mm: Correct fixmap pagetable types
arm64: compat: fix compat types affecting struct compat_elf_prpsinfo
arm64: Align less than PAGE_SIZE pgds naturally
arm64: Allow 48-bits VA space without ARM_SMMU
1) Fix boots with gcc-4.9 compiled sparc64 kernels.
2) Add missing __get_user_pages_fast() on sparc64 to fix hangs on
futexes used in transparent hugepage areas.
It's really idiotic to have a weak symbolled fallback that just
returns zero, and causes this kind of bug. There should be no
backup implementation and the link should fail if the architecture
fails to provide __get_user_pages_fast() and supports transparent
hugepages.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Implement __get_user_pages_fast().
sparc64: Fix register corruption in top-most kernel stack frame during boot.
Linus Torvalds [Fri, 24 Oct 2014 19:42:55 +0000 (12:42 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"This is a pretty large update. I think it is roughly as big as what I
usually had for the _whole_ rc period.
There are a few bad bugs where the guest can OOPS or crash the host.
We have also started looking at attack models for nested
virtualization; bugs that usually result in the guest ring 0 crashing
itself become more worrisome if you have nested virtualization,
because the nested guest might bring down the non-nested guest as
well. For current uses of nested virtualization these do not really
have a security impact, but you never know and bugs are bugs
nevertheless.
A lot of these bugs are in 3.17 too, resulting in a large number of
stable@ Ccs. I checked that all the patches apply there with no
conflicts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vfio: fix unregister kvm_device_ops of vfio
KVM: x86: Wrong assertion on paging_tmpl.h
kvm: fix excessive pages un-pinning in kvm_iommu_map error path.
KVM: x86: PREFETCH and HINT_NOP should have SrcMem flag
KVM: x86: Emulator does not decode clflush well
KVM: emulate: avoid accessing NULL ctxt->memopp
KVM: x86: Decoding guest instructions which cross page boundary may fail
kvm: x86: don't kill guest on unknown exit reason
kvm: vmx: handle invvpid vm exit gracefully
KVM: x86: Handle errors when RIP is set during far jumps
KVM: x86: Emulator fixes for eip canonical checks on near branches
KVM: x86: Fix wrong masking on relative jump/call
KVM: x86: Improve thread safety in pit
KVM: x86: Prevent host from panicking on shared MSR writes.
KVM: x86: Check non-canonical addresses upon WRMSR
Linus Torvalds [Fri, 24 Oct 2014 19:41:50 +0000 (12:41 -0700)]
Merge tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
* tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Allocate memory for physdev_pci_device_add's optarr
x86/xen: panic on bad Xen-provided memory map
x86/xen: Fix incorrect per_cpu accessor in xen_clocksource_read()
x86/xen: avoid race in p2m handling
x86/xen: delay construction of mfn_list_list
x86/xen: avoid writing to freed memory after race in p2m handling
xen/balloon: Don't continue ballooning when BP_ECANCELED is encountered
Linus Torvalds [Fri, 24 Oct 2014 19:35:48 +0000 (12:35 -0700)]
Merge tag 'sound-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a chunk of small fixes since rc1: two PCM core fixes, one is
a long-standing annoyance about lockdep and another is an ARM64 mmap
fix.
The rest are a HD-audio HDMI hotplug notification fix, a fix for
missing NULL termination in Realtek codec quirks and a few new
device/codec-specific quirks as usual"
* tag 'sound-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add missing terminating entry to SND_HDA_PIN_QUIRK macro
ALSA: pcm: Fix false lockdep warnings
ALSA: hda - Fix inverted LED gpio setup for Lenovo Ideapad
ALSA: hda - hdmi: Fix missing ELD change event on plug/unplug
ALSA: usb-audio: Add support for Steinberg UR22 USB interface
ALSA: ALC283 codec - Avoid pop noise on headphones during suspend/resume
ALSA: pcm: use the same dma mmap codepath both for arm and arm64
Linus Torvalds [Fri, 24 Oct 2014 19:33:32 +0000 (12:33 -0700)]
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random updates from Ted Ts'o:
"This adds a memzero_explicit() call which is guaranteed not to be
optimized away by GCC. This is important when we are wiping
cryptographically sensitive material"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
crypto: memzero_explicit - make sure to clear out sensitive data
random: add and use memzero_explicit() for clearing data
Linus Torvalds [Fri, 24 Oct 2014 18:29:31 +0000 (11:29 -0700)]
Merge tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This is material that didn't make it to my 3.18-rc1 pull request for
various reasons, mostly related to timing and travel (LinuxCon EU /
LPC) plus a couple of fixes for recent bugs.
The only really new thing here is the PM QoS class for memory
bandwidth, but it is simple enough and users of it will be added in
the next cycle. One major change in behavior is that platform devices
enumerated by ACPI will use 32-bit DMA mask by default. Also included
is an ACPICA update to a new upstream release, but that's mostly
cleanups, changes in tools and similar. The rest is fixes and
cleanups mostly.
Specifics:
- Fix for a recent PCI power management change that overlooked the
fact that some IRQ chips might not be able to configure PCIe PME
for system wakeup from Lucas Stach.
- Fix for a bug introduced in 3.17 where acpi_device_wakeup() is
called with a wrong ordering of arguments from Zhang Rui.
- A bunch of intel_pstate driver fixes (all -stable candidates) from
Dirk Brandewie, Gabriele Mazzotta and Pali Rohár.
- Fixes for a rather long-standing problem with the OOM killer and
the freezer that frozen processes killed by the OOM do not actually
release any memory until they are thawed, so OOM-killing them is
rather pointless, with a couple of cleanups on top (Michal Hocko,
Cong Wang, Rafael J Wysocki).
- ACPICA update to upstream release 20140926, inlcuding mostly
cleanups reducing differences between the upstream ACPICA and the
kernel code, tools changes (acpidump, acpiexec) and support for the
_DDN object (Bob Moore, Lv Zheng).
- New PM QoS class for memory bandwidth from Tomeu Vizoso.
- Default 32-bit DMA mask for platform devices enumerated by ACPI
(this change is mostly needed for some drivers development in
progress targeted at 3.19) from Heikki Krogerus.
- ACPI EC driver cleanups, mostly related to debugging, from Lv
Zheng.
- cpufreq-dt driver updates from Thomas Petazzoni.
- powernv cpuidle driver update from Preeti U Murthy"
* tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
intel_pstate: Correct BYT VID values.
intel_pstate: Fix BYT frequency reporting
intel_pstate: Don't lose sysfs settings during cpu offline
cpufreq: intel_pstate: Reflect current no_turbo state correctly
cpufreq: expose scaling_cur_freq sysfs file for set_policy() drivers
cpufreq: intel_pstate: Fix setting max_perf_pct in performance policy
PCI / PM: handle failure to enable wakeup on PCIe PME
ACPI: invoke acpi_device_wakeup() with correct parameters
PM / freezer: Clean up code after recent fixes
PM: convert do_each_thread to for_each_process_thread
OOM, PM: OOM killed task shouldn't escape PM suspend
freezer: remove obsolete comments in __thaw_task()
freezer: Do not freeze tasks killed by OOM killer
ACPI / platform: provide default DMA mask
cpuidle: powernv: Populate cpuidle state details by querying the device-tree
cpufreq: cpufreq-dt: adjust message related to regulators
cpufreq: cpufreq-dt: extend with platform_data
cpufreq: allow driver-specific data
ACPI / EC: Cleanup coding style.
ACPI / EC: Refine event/query debugging messages.
...
Linus Torvalds [Fri, 24 Oct 2014 18:21:43 +0000 (11:21 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
Catalin Marinas [Fri, 24 Oct 2014 17:16:47 +0000 (18:16 +0100)]
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
With 48-bit VA space, the 64K page configuration uses 3 levels instead
of 2 and PUD_SIZE != PMD_SIZE. Since with 64K pages we only cover
PMD_SIZE with the initial swapper_pg_dir populated in head.S, the
memblock current_limit needs to be set accordingly in map_mem() to avoid
allocating unmapped memory. The memblock current_limit is progressively
increased as more blocks are mapped.
David S. Miller [Fri, 24 Oct 2014 16:59:02 +0000 (09:59 -0700)]
sparc64: Implement __get_user_pages_fast().
It is not sufficient to only implement get_user_pages_fast(), you
must also implement the atomic version __get_user_pages_fast()
otherwise you end up using the weak symbol fallback implementation
which simply returns zero.
This is dangerous, because it causes the futex code to loop forever
if transparent hugepages are supported (see get_futex_key()).
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Oct 2014 19:58:13 +0000 (12:58 -0700)]
sparc64: Fix register corruption in top-most kernel stack frame during boot.
Meelis Roos reported that kernels built with gcc-4.9 do not boot, we
eventually narrowed this down to only impacting machines using
UltraSPARC-III and derivitive cpus.
The crash happens right when the first user process is spawned:
[ 54.451346] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[ 54.451346]
[ 54.571516] CPU: 1 PID: 1 Comm: init Not tainted 3.16.0-rc2-00211-gd7933ab #96
[ 54.666431] Call Trace:
[ 54.698453] [0000000000762f8c] panic+0xb0/0x224
[ 54.759071] [000000000045cf68] do_exit+0x948/0x960
[ 54.823123] [000000000042cbc0] fault_in_user_windows+0xe0/0x100
[ 54.902036] [0000000000404ad0] __handle_user_windows+0x0/0x10
[ 54.978662] Press Stop-A (L1-A) to return to the boot prom
[ 55.050713] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
Further investigation showed that compiling only per_cpu_patch() with
an older compiler fixes the boot.
Detailed analysis showed that the function is not being miscompiled by
gcc-4.9, but it is using a different register allocation ordering.
With the gcc-4.9 compiled function, something during the code patching
causes some of the %i* input registers to get corrupted. Perhaps
we have a TLB miss path into the firmware that is deep enough to
cause a register window spill and subsequent restore when we get
back from the TLB miss trap.
Let's plug this up by doing two things:
1) Stop using the firmware stack for client interface calls into
the firmware. Just use the kernel's stack.
2) As soon as we can, call into a new function "start_early_boot()"
to put a one-register-window buffer between the firmware's
deepest stack frame and the top-most initial kernel one.
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Chandran [Fri, 10 Oct 2014 11:31:24 +0000 (12:31 +0100)]
arm64: ASLR: Don't randomise text when randomise_va_space == 0
When user asks to turn off ASLR by writing "0" to
/proc/sys/kernel/randomize_va_space there should not be
any randomization to mmap base, stack, VDSO, libs, text and heap
Currently arm64 violates this behavior by randomising text.
Fix this by defining a constant ELF_ET_DYN_BASE. The randomisation of
mm->mmap_base is done by setup_new_exec -> arch_pick_mmap_layout ->
mmap_base -> mmap_rnd.
Imre Deak [Thu, 23 Oct 2014 16:23:28 +0000 (19:23 +0300)]
drm/i915: add comments on what stage a given PM handler is called
This will hopefully make it easier to navigate the code without the need
to consult the full PM documentation.
v2:
- add a comment that the freeze handler is also called after rebooting
- add a comment that the thaw handler is also called to recover from
errors (Ville)
- add the PM event names (PMSG_THAW etc.) for reference (Ville)
- add comments that s0ix can be handled both via system and runtime
suspend (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:27 +0000 (19:23 +0300)]
drm/i915: unify switcheroo and legacy suspend/resume handlers
By now we handle switcheroo and legacy suspend/resume the same way, so
no need to keep separate functions for them.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:26 +0000 (19:23 +0300)]
drm/i915: add poweroff_late handler
The suspend_late handler saves some registers and powers off the device,
so it doesn't have a big overhead. Calling it at S4 poweroff_late time
makes the power off handling identical to the S3 suspend and S4 freeze
handling, so do this for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:25 +0000 (19:23 +0300)]
drm/i915: sanitize suspend/resume helper function names
By now the S4 freeze/thaw and S3 suspend/resume events are handled the
same way, so we can rename the freeze/thaw internal helpers to
suspend/resume accordingly to make clearer what the helpers do. Also
rename i915_resume_early to i915_drm_resume_early aligning it with the
rest of the helper names.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:24 +0000 (19:23 +0300)]
drm/i915: unify S3 and S4 suspend/resume handlers
The S3 and S4 events are now handled the same way internally, there is no
need to keep separate wrapper functions around them. Simply reuse the
suspend/resume versions everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:23 +0000 (19:23 +0300)]
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
We already disable everything during S4 freeze, except the PCI device
itself. There is no reason why we couldn't disable that too and doing
so allows us to unify these handlers in the next patch with the
corresponding S3 suspend/resume handlers.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:22 +0000 (19:23 +0300)]
drm/i915: enable output polling during S4 thaw
To avoid processing hotplug events we disable connector polling for the
duration of S3 suspend. We also disable it for S4 freeze, and keep it
disabled after S4 thaw. This won't prevent though hotplug processing,
since we re-enable interrupts anyway. There is also no need to prevent
it at that time, since we reinitialize everything during thaw, so the
device is in a consistent state. So to simplify things enable polling
during thaw, which will allow us to handle S4 thaw the same way as S3
resume in an upcoming patch.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:21 +0000 (19:23 +0300)]
drm/i915: check for GT faults in all resume handlers and driver load time
Checking for GT faults is not specific in any way to S4 thaw, so do it
also during S3 resume, S4 restore and driver load time. This allows us to
unify the Sx handlers in an upcoming patch.
v2:
- move the check to intel_uncore_early_sanitize(), so we check at driver
load time too (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:20 +0000 (19:23 +0300)]
drm/i915: remove unused restore_gtt_mappings optimization during suspend
The logic to skip restoring GTT mappings was added to speed up
suspend/resume, but not on old GENs where not restoring them caused
problems. The check for old GENs is based on the existence of OpRegion,
but this doesn't work since opregion is initialized only after
the check. So we end up always restoring the mappings.
On my BYT - which has OpRegion - skipping restoring the mappings during
suspend doesn't work, I get a GPU hang after resume. Also the logic of
when to allow the optimization during S4 is reversed: we should allow it
during S4 thaw but not during S4 restore, but atm we have it the other
way around in the code.
Since correctness wins over optimal code and since the optimization
wasn't used anyway I decided not to try to fix it at this point, but
just remove it. This allows us to unify the S3 and S4 handlers in the
following patches.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:19 +0000 (19:23 +0300)]
drm/i915: fix S4 suspend while switcheroo state is off
If the device is suspended already through the switcheroo interface we
shouldn't suspend it again or resume it after suspend. We have the
corresponding check for S3 suspend already, add it for all the other
S3 and S4 handlers. Also move the check from i915_resume_early() to
i915_resume_legacy(), so that it's done in the high level handler for
all PM events.
v2:
- fix the resume path too, we don't need to special case there
DRM_SWITCH_POWER_OFF with the device being enabled (in which case we'd
have to disable the device), since that never happens (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During switcheroo/legacy suspend we don't call the suspend_late handler
but when resuming afterwards we call resume_early. This happened to work
so far, since suspend_late only disabled the PCI device. This changed in
drm/i915: Sharing platform specific sequence between runtime and system susp
after which we also saved/restored the VLV Gunit HW state in
suspend_late/resume_early. So now since we don't save the state during
suspend a following resume will restore a corrupted state.
Fix this by calling the suspend_late handler during both switcheroo and
legacy suspend.
CC: Sagar Kamble <sagar.a.kamble@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:17 +0000 (19:23 +0300)]
drm/i915: propagate error from legacy resume handler
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:16 +0000 (19:23 +0300)]
drm/i915: unify legacy S3 suspend and S4 freeze handlers
i915_suspend() is called from the DRM legacy S3 suspend/S4 freeze paths
and the switcheroo suspend path. For switcheroo we only ever need to
perform a full suspend (PM_EVENT_SUSPEND) and for the DRM legacy path
we can handle the S4 freeze (PM_EVENT_FREEZE) the same way as S3
suspend. The only difference atm between suspend and freeze is that
during freeze we don't disable the PCI device, but there is no reason
why we can't do so. So unify the two cases to reduce complexity.
Note that for the DRM legacy case the thaw event is not handled, so
we disable the display before creating the hibernation image and it
won't get re-enabled until reboot. We could fix this leaving the
display enabled for the image creation/writing (if we care enough
about UMS), but this can be done as a follow-up.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 23 Oct 2014 16:23:15 +0000 (19:23 +0300)]
drm/i915: factor out i915_drm_suspend_late
This is needed by an upcoming patch fixing the switcheroo/legacy suspend
paths.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Arun Siluvery [Wed, 22 Oct 2014 17:59:52 +0000 (18:59 +0100)]
drm/i915: Emit even number of dwords when emitting LRIs
The number of DWords should be even when doing ring emits as
command sequences require QWord alignment.
There was some discussion about the maximum length of the MI_LRI
command. Quoting Mika
"I did some test with bdw:
"The maximum is 128 writes, resulting the 8 bit length
field of the command being 0xff, thus following the spec.
The 128'th write went through.
"Perhaps the max command length is then less in older gens?
"Perhaps WARN_ON(x > 128) in MI_LOAD_REGISTER_IMM would be in place
but one needs minor tweak to command parser a bit also then.
#define I915_MAX_WA_REGS 16
keeps us safe for now atleast."
Ville commented that on pre-gen6 the length field seems to be
restricted to 0x3f though. So for all cases we should be ok.
v2: user LRI variant that can write multiple regs in one go (Damien).
We can simply insert one NOP at the end instead of one per register write.
Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add a summary of the MI_LRI length discussion.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 23 Oct 2014 14:41:34 +0000 (07:41 -0700)]
drm/i915: Add rotation support for cursor plane (v5)
The cursor plane also supports 180 degree rotation. Add a new
"cursor-rotation" property on the crtc which controls this.
Unlike sprites, the cursor has a fixed size, so if you have a small
cursor image with the rest of the bo filled by transparent pixels,
simply flipping the rotation property will cause the visible part
of the cursor to shift. This is something to keep in mind when
using cursor rotation.
v2: Fix gen4/vlv by offsetting the base address appropriately
v3: Removing cursor-rotation property and using rotation property on cursor
plane.
v4: Changing the author name back to Ville.
v5 (by Matt Roper): Slight tweaking to apply against latest di-nightly
codebase.
Cc: Sagar Kamble <sagar.a.kamble@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Sonika Jindal <sonika.jindal@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yu Zhang [Thu, 23 Oct 2014 07:28:24 +0000 (15:28 +0800)]
drm/i915: use macros to assign mmio access functions
This is beautification prep work since vgt will add even more special
cases. With these macros it's much easier to see what's going on
really.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
[danvet: #undef the temporary macros after the function again. And
write a commit message.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Oct 2014 19:11:11 +0000 (16:11 -0300)]
drm/i915: only run hsw_power_well_post_enable when really needed
Only run it after we actually enable the power well. When we're
booting the machine there are cases where we run
hsw_power_well_post_enable without really needing, and even though
this is not causing any real bugs, it is unneeded and causes confusion
to people debugging interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 17 Oct 2014 15:05:08 +0000 (08:05 -0700)]
drm/i915/chv: Use 16 and 32 for low and high drain latency precision.
Current chv spec teels we can only use either 16 or 32 bits as precision.
Although in the past VLV went from 16/32 to 32/64 and spec might not be updated,
these precision values brings stability and fixes some issues Wayne was facing.
Cc: Wayne Boyer <wayne.boyer@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Tested-by: Wayne Boyer <wayne.boyer@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Sprinkle const as requested by Ville.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Clear TX FIFO reset master override bits on chv
Fortunately the bit in DW0 that was cleared due to this didn't have
any effect as long as the bit we meant to clear was already zero.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix commit ref as pointed out by Jani.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 17:52:30 +0000 (20:52 +0300)]
drm/i915: Don't claim that we're resetting PCH ADPA register
intel_crt_reset() resets the ADPA register on all gen5+ platforms.
However the debug message claims it's touching the PCH ADPA register
which is clearly not what it does on VLV. Drop the PCH part from
the debug message.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 17 Oct 2014 21:42:03 +0000 (18:42 -0300)]
drm/i915: disable IPS while getting the pipe CRCs.
For some yet-undiscovered reason, when IPS gets enabled, the pipe CRC
changes. Since hsw_enable_ips() doesn't really guarantees to enable
IPS (it depends on package C-states), we can't really predict if IPS
is enabled or disabled while running our CRC tests, so let's just
completely disable IPS while pipe CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch. While this doesn't happen,
let's merge this patch, so every IGT test relying on the CRCs can
work on pipe A.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Testcase: igt/kms_cursor_crc (and others) Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This means it has to be before intel_modeset_cleanup, which cleans the
CRTC structures. But if we move it to before intel_fbdev_fini(), we
get WARNs because intel_fbdev_fini() still tries to use the vblanks,
so the only acceptable point for drm_vblank_cleanup() seems to be this
place.
Related commit:
commit cbb47d179fb345c579cd8cd884693903fceed26a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 23 17:33:20 2013 -0300
drm/i915: Add some missing steps to i915_driver_load error path
Testsuite: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77511
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83484 Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 10 Oct 2014 14:53:33 +0000 (17:53 +0300)]
drm/i915: spt does not have pch backlight override bit
SPT is always in the PCH override mode, and the bit MBZ. Only set
override on LPT.
v2: check for PCH version (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Thu, 9 Oct 2014 19:57:43 +0000 (12:57 -0700)]
drm/i915: preserve swizzle settings if necessary v4
Some machines (like MBAs) might use a tiled framebuffer but not enable
display swizzling at boot time. We want to preserve that configuration
if possible to prevent a boot time mode set. On IVB+ it shouldn't
affect performance anyway since the memory controller does internal
swizzling anyway.
For most other configs we'll be able to enable swizzling at boot time,
since the initial framebuffer won't be tiled, thus we won't see any
corruption when we enable it.
v2: preserve swizzling if BIOS had it set (Daniel)
v3: preserve swizzling only if we inherited a tiled framebuffer (Daniel)
check display swizzle setting in detect_bit_6_swizzle (Daniel)
use gen6 as cutoff point (Daniel)
v4: fixup swizzle preserve again, had wrong init order (Daniel)
Reported-by: Kristian Høgsberg <hoegsberg@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 10 Sep 2014 15:16:54 +0000 (18:16 +0300)]
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
During S4 freeze we don't call intel_suspend_complete(), which would
save the gunit HW state, but during S4 thaw/restore events we call
intel_resume_prepare() which restores it, thus ending up in a corrupted
HW state.
Fix this by calling intel_suspend_complete() from the corresponding
freeze_late event handler.
The issue was introduced in
commit 016970beb05da6285c2f3ed2bee1c676cb75972e
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
CC: Sagar Kamble <sagar.a.kamble@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 7 Oct 2014 14:21:26 +0000 (17:21 +0300)]
drm/i915: Build workaround list in ring initialization
If we build the workaround list in ring initialization
and decouple it from the actual writing of values, we
gain the ability to decide where and how we want to apply
the values.
The advantage of this will become more clear when
we need to initialize workarounds on older gens where
it is not possible to write all the registers through ring
LRIs.
v2: rebase on newest bdw workarounds
Cc: Arun Siluvery <arun.siluvery@linux.intel.com> Cc: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Resolve tiny conflict in comments and ocd alignments a bit.]
[danvet2: Remove bogus force_wake_get call spotted by Paulo and QA.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 10 Sep 2014 15:16:55 +0000 (18:16 +0300)]
drm/i915: remove dead code from legacy suspend handler
The legacy DRM suspend logic (effective in UMS) doesn't handle any S4 thaw
events so we don't need to care about it either. Only S3 suspend and S4
freeze events are handled. Leave an assert behind to be sure.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Replace some loop through encoders with intel_pipe_has_type()
In the ironlake mode set code, there was two instances of a loop through
encoders to find out if one of them has INTEL_OUTPUT_LVDS type. Simplify
the code by deleting some lines and use intel_pipe_has_type() instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 16 Oct 2014 10:28:18 +0000 (12:28 +0200)]
drm/i915: Document that mmap forwarding is discouraged
Too many new drm driver writers seem to look at i915 for inspiration.
But we have two ways to do mmap, so discourage readers from the old,
ugly version. In a new driver we'd just expose two mmap offsets per
object, one for the gtt map and the other for the cpu map.
v2: Make it clear that i915 does cpu mmaps this way for past
cluelessness^W^W historical reasons. Asked for by Jani.
Cc: "Cheng, Yao" <yao.cheng@intel.com> Cc: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Sun, 24 Aug 2014 18:35:31 +0000 (19:35 +0100)]
drm/i915: Convert a couple more INTEL_INFO-esque macros to be pointer agnostic
Just a couple more macros that assume that they were being passed a
struct drm_device when they want a struct drm_i915_private. Use our
magic macro to ease transitioning over to using drm_i915_privates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 8 Oct 2014 10:25:17 +0000 (11:25 +0100)]
drm/i915: Suppress no action noise from oom shrinker
If we are not able to free anything (the shrinker leaves nothing on the
global object lists), do not log anything. This is useful when other
subsystems are being stress-tested for their oom behaviour and i915.ko
is shouting into the logs about doing nothing.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 8 Oct 2014 10:25:16 +0000 (11:25 +0100)]
drm/i915: Report the current number of bytes freed during oom
The shrinker reports the number of pages freed, but we try to log the
number of bytes - which leads to some nonsense values being reportedly
freed during oom.
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Tue, 7 Oct 2014 14:06:50 +0000 (07:06 -0700)]
drm/i915: Do not export RC6p and RC6pp if they don't exist
Avoid to expose RC6 and RC6pp to the platforms that doesn't support it.
So powertop can be changed to show RC6p and RC6pp only on the platforms
they are available.
v2: Simplify by merging RC6p and RC6pp groups and respect the spec that
mentions deep and deepest RC6 on SNB and IVB although they keep disabled
by default.
v3: Remove unecessary space.
v4: RC6p and RC6pp is only for SNB and IVB; unify debug msg and use
has_rc6p() on sanitize options instead of is gen 6 and ivb.
v5: yet another fix on has_rc6p macro. final is_gen6 or is_ivb! To make sure
we are excluding hsw and baytrail.
References: https://bugs.freedesktop.org/show_bug.cgi?id=84524 Cc: Josh Triplett <josh.triplett@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: move check of intel_crtc_cursor_set_obj() out
Move check inside intel_crtc_cursor_set_obj() to
intel_check_cursor_plane(), we only use it there so move them out to
make the merge of intel_crtc_cursor_set_obj() into
intel_check_cursor_plane() easier.
This is another step toward the atomic modesetting support and unification
of plane operations such pin/unpin of fb objects on i915.
v2: take Ville's comment: move crtc_{w,h} assignment a bit down in the
code
v3: take Ville's comment: kept only the restructuring changes, the rest of
the code was moved to a separated patch since it is a bug fix (we weren't
checking sizes when the fb was the same)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
[danvet: Fixup commit message mixup.] Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Merge of visible and !visible paths for primary planes
Fold intel_pipe_set_base() in the update primary plane path merging
pieces of code that are common to both paths.
Basically the the pin/unpin procedures are the same for both paths
and some checks can also be shared (some of the were moved to the
check() stage)
v2: take Ville's comments:
- remove unnecessary plane check
- move mutex lock to inside the conditional
- make the pin fail message a debug one
- add a fixme for the fastboot hack
- call intel_frontbuffer_flip() after FBC update
v3: take more Ville's comments:
- fold update code under if (intel_crtc->active), and do the
visible/!visible split inside.
- check ret inside the same conditional we assign it
v4: don't use intel_enable_primary_hw_plane(), the primary_enabled
check inside will break page flips
v5: take more Ville's comments:
- set primary_enabled to true and add BDW hack
- unify if (old_fb) and if (old_fb != fb)
v6: take more Ville's comments:
- make was_primary bool and fix its check
- add the BDW vblank wait comment
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 1 Oct 2014 19:04:15 +0000 (20:04 +0100)]
drm/i915: Spell out IS_HSW/BDW_ULT() in intel_crt_present()
The quality of being a ULT or ULX package doesn't tell anything across
generations and so a global IS_ULT() macro doesn't make much sense, esp.
as we're adding new products.
So, spell out which ULT/ULX SKUs we are talking about here, namely HSW
and BDW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / karo-tx-linux.git / log