Michael Chan [Wed, 27 Sep 2006 23:00:40 +0000 (16:00 -0700)]
[TG3]: Improve ASF heartbeat.
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 27 Sep 2006 22:59:15 +0000 (15:59 -0700)]
[TG3]: Improve 5704S autoneg.
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Bluetooth] Support create connection cancel command
In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
[Bluetooth] Read local version information on device init
The local version information are needed to identify certain feature
sets of devices. They must be read on device init and stored for later
use. It is also possible to access them through the device model.
[Bluetooth] Integrate services into the driver model
This patch integrates the services of the Bluetooth protocols RFCOMM,
BNEP and HIDP into the driver model. This makes it possible to assign
the virtual TTY, network and input devices to a specific Bluetooth
connection.
[Bluetooth] Integrate low-level connections into the driver model
This patch integrates the low-level connections (ACL and SCO) into the
driver model. Every connection is presented as device with the parent
set to its host controller device.
Eric Sesterhenn [Wed, 27 Sep 2006 06:26:38 +0000 (23:26 -0700)]
[RTNETLINK]: Possible dereference in net/core/rtnetlink.c
another possible dereference spotted by coverity (#cid 1390).
if the nlmsg_parse() call fails, we goto errout, where we call
dev_put(), with dev still initialized to NULL.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* add svc_getnl():
Take network-endian value from buffer, convert to host-endian
and return it.
* add svc_putnl():
Take host-endian value, convert to network-endian and put it
into a buffer.
* annotate svc_getu32()/svc_putu32() as dealing with network-endian.
* convert to svc_getnl(), svc_putnl().
[AV: in large part it's a carved-up Alexey's patch]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Wed, 27 Sep 2006 05:18:43 +0000 (22:18 -0700)]
[IPV4]: inetpeer annotations
This one is interesting - we use net-endian value as search key, but
order the tree by *host-endian* comparisons of keys. OK since we only
care about lookups. Annotated inet_getpeer() and friends.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Wed, 27 Sep 2006 04:25:20 +0000 (21:25 -0700)]
[IPV4]: ip_route_input() annotations
ip_route_input() takes net-endian source and destination address.
* Annotated as such.
* arguments of its invocations annotated where needed.
* local helpers getting the same values passed to by it (ip_route_input_mc(),
ip_route_input_slow(), ip_handle_martian_source(), ip_mkroute_input(),
ip_mkroute_input_def(), __mkroute_input()) annotated
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chuck Short <zulcss@gmail.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
A while ago Ingo patched tcp_v4_rcv on net/ipv4/tcp_ipv4.c to use
bh_lock_sock_nested and silence a lock validator warning. This fixed
it for IPv4, but recently I saw a report of the same warning on IPv6.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Stern [Tue, 26 Sep 2006 18:51:48 +0000 (14:51 -0400)]
USB: g_file_storage: Set sense info Valid bit only when needed
Strictly speaking, the Valid bit in SCSI sense data is supposed to
be set only when the Information field contains a valid number. This
patch (as793) turns off the Valid bit when the Information field
hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 26 Sep 2006 18:46:16 +0000 (14:46 -0400)]
OHCI: add auto-stop support
This patch (as790b) adds "autostop" support to ohci-hcd: the driver
will automatically stop the host controller when no devices have been
connected for at least one second. This feature is useful when the
USB autosuspend facility isn't available, such as when
CONFIG_USB_SUSPEND hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 25 Sep 2006 19:41:21 +0000 (15:41 -0400)]
OHCI: remove existing autosuspend code
The autosuspend technique used by ohci-hcd doesn't mesh well with the
newer USB core autosuspend code. This patch (as789) removes ohci-hcd's
autosuspend support. Now the driver will be usable, but it won't
automatically go into a low-power state when no devices are connected.
That's for a later patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 25 Sep 2006 19:41:12 +0000 (15:41 -0400)]
USB: allow both root-hub interrupts and polling
Originally I didn't think any host controller driver would ever use
interrupts and polling at the same time, but it turns out ohci-hcd wants
to do exactly that. This patch (as788) makes it possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 19 Sep 2006 14:14:07 +0000 (10:14 -0400)]
USB: create new workqueue thread for USB autosuspend
This patch (as787) creates a new workqueue thread to handle delayed
USB autosuspend requests. Previously the code used keventd. However
it turns out that the hub driver's suspend routine calls
flush_scheduled_work(), making it a poor candidate for running in
keventd (the call immediately deadlocks). The solution is to use a
new thread instead of keventd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: add Raritan KVM USB Dongle to the HID_QUIRK_NOGET blacklist
During Installation the host tries to enumerate the keyboard/mouse
dongle for the Raritan KVM.At this time timeouts have been observed
Adding the Raritan KVM USB dongle to the blacklist fixes this issue.
USB: add SeaLevel 2106 SeaLINK support to ftdi_sio
We have a couple of these USB-Serial converters around; they're slightly
different from the 2104 models in that they can handle 500Kb/sec over RS422.
The existing ftdi driver seems to work just fine if we add in the
appropriate IDs.
Patch is against 2.6.17.6, but should apply cleanly to pretty much
anything recent.
Ian Abbott [Mon, 25 Sep 2006 13:19:19 +0000 (14:19 +0100)]
USB serial ftdi_sio: Add support for Tactrix OpenPort devices
This patch adds support for three OpenPort ECU data cables from Tactrix
Inc. to the ftdi_sio driver's device ID table. One of the PIDs was
supplied by Donour Sizemore on the ftdi-usb-sio-devel mailing list. The
other two were added by myself after examining the Windows driver software.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempting to read the ethernet ID directly from the eeprom somehow
confuses ADM8515. Subsequent read requests to either the eeprom or the MII
fail as well. Didn't dig much deeper, though. For example ADM8513 does
not experience this problem.
I used the fact that at power up the device is reading its ID automatically
(not true for older Pegasus based devices) and put it in the Ethernet ID
registers. So now the driver uses get_registers() instead of
read_eprom_word() if the device is Pegasus_II based one. Tested it with
all (Pegasus and Pegasus_II) gadgets i have and everything seems ok.
Cc: <jogeedaklown@yahoo.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jim Cromie [Sun, 24 Sep 2006 19:22:52 +0000 (21:22 +0200)]
w83781d: Fix unchecked return status
w83781d: Fix unchecked return status
Add 2 attr-file groups (for base and model-specific attrs respectively),
create the base group with single call to sysfs_create_group,
check the return code on individual calls to device_create_file for each
of the model-specific attr-files.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 24 Sep 2006 19:16:40 +0000 (21:16 +0200)]
hwmon: Fix unchecked return status, batch 4
hwmon: Fix unchecked return status, batch 4
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Note: f71805f actually checked the status from device_create_file
already. However it did not remove the files on device destruction.
It was also an opportunity to use sysfs_create/remove_group instead
of hand-made loops. This makes the changes much more important but
I think the result is worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark M. Hoffman [Sun, 24 Sep 2006 19:15:35 +0000 (21:15 +0200)]
hwmon: Fix unchecked return status, batch 3
hwmon: Fix unchecked return status, batch 3
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark M. Hoffman [Sun, 24 Sep 2006 19:14:35 +0000 (21:14 +0200)]
hwmon: Fix unchecked return status, batch 2
hwmon: Fix unchecked return status, batch 2
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Hubbard [Sun, 24 Sep 2006 19:04:38 +0000 (21:04 +0200)]
w83627ehf: Fix unchecked return status
w83627ehf: Fix unchecked return status
Fix: check return value from device_create_file()
Fix: call device_remove_file() on error and module unload
Fix: call hwmon_device_register() after device_create_file() to eliminate race
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jim Cromie [Sun, 24 Sep 2006 19:03:25 +0000 (21:03 +0200)]
pc87360: Check for error on sysfs files creation
pc87360: Check for error on sysfs files creation
Use sysfs_create_group() for 2 sensor-types which are chip-model
invariant, i.e. all-or-nothing attribute groups.
Other 2 groups vary too much due to configuration, etc, so we keep the
loops of device_create_file(), but now check their returns.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-beck.git / log