Olof Johansson [Tue, 20 Dec 2011 05:09:48 +0000 (21:09 -0800)]
Merge branch 'omap/uart' into next/pm
* omap/uart: (32 commits)
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: UART: Fix compilation/sparse warnings
ARM: OMAP2+: UART: Remove omap_uart_can_sleep and add pm_qos
ARM: OMAP2+: UART: Do not gate uart clocks if used for debug_prints
ARM: OMAP2+: UART: Avoid uart idling on suspend for no_console_suspend usecase
ARM: OMAP2+: UART: Avoid console uart idling during bootup
ARM: OMAP2+: UART: remove temporary variable used to count uart instance
ARM: OMAP2+: UART: Make the RX_TIMEOUT for DMA configurable for each UART
ARM: OMAP2+: UART: Allow UART parameters to be configured from board file.
ARM: OMAP2+: UART: Remove old and unused clocks handling funcs
ARM: OMAP2+: UART: Add wakeup mechanism for omap-uarts
ARM: OMAP2+: UART: Move errata handling from serial.c to omap-serial
ARM: OMAP2+: UART: Get context loss count to context restore
ARM: OMAP2+: UART: Remove uart reset function.
ARM: OMAP2+: UART: Ensure all reg values configured are available from port structure
ARM: OMAP2+: UART: Remove context_save and move context restore to driver
...
Olof Johansson [Tue, 20 Dec 2011 05:04:42 +0000 (21:04 -0800)]
Merge branch 'omap/prcm' into next/pm
* omap/prcm:
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
Holger Brunck [Mon, 19 Dec 2011 16:49:48 +0000 (17:49 +0100)]
ARM: plat-orion: make gpiochip label unique
The former implementation adds a fix gpiochip label string
to the framework. This is confusing because orion_gpio_init
is called more than once and this ends up in different gpiochips
with the same label.
This patch adds the already present orion_gpio_chip_count to the
label string to make it unique in the system.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Lennert Buytenhek <kernel@wantstofly.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Eric Bénard [Tue, 13 Dec 2011 06:31:43 +0000 (07:31 +0100)]
cpuimx35sd: fix Kconfig
in 0d6cfa3a75f5cde5b3ca0dde748fd22625b4f34c I fixed the mach-types
records. We also need to make the name consistent in Kconfig else
the machine_is_eukrea_cpuimx35sd macro fails, and thus audio codec
is not properly initalized.
Eric Bénard [Tue, 13 Dec 2011 14:13:19 +0000 (15:13 +0100)]
clock-imx35: fix reboot in internal boot mode
commit 8d75a26 "ARM: mx35: use generic function for displaying silicon revision"
disabled IIM clock after reading silicon revision which will prevent
reboot in internal boot mode.
Signed-off-by: Eric Bénard <eric@eukrea.com> Cc: Jason Liu <jason.hui@linaro.org> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 13 Dec 2011 14:12:55 +0000 (15:12 +0100)]
dma: MX3_IPU fix depends
ARCH_MX3 was removed in commit a89cf59 :
"arm/imx: merge i.MX3 and i.MX6"
thus preventing to select MX3_IPU, thus preventing IPU and display
to work on i.MX3x SOC.
i.MX SDMA support is also affected.
Signed-off-by: Eric Bénard <eric@eukrea.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 13 Dec 2011 06:31:35 +0000 (07:31 +0100)]
cpuimx25sd: fix Kconfig
in 0d6cfa3a75f5cde5b3ca0dde748fd22625b4f34c I fixed the mach-types
records. We also need to make the name consistent in Kconfig else
the machine_is_eukrea_cpuimx25sd macro fails, and thus audio codec
is not properly initalized.
Richard Zhao [Tue, 13 Dec 2011 06:25:27 +0000 (14:25 +0800)]
arm/imx: fix cpufreq section mismatch
WARNING: arch/arm/plat-mxc/built-in.o(.data+0x488): Section mismatch in reference from the variable mxc_driver to the function .init.text:mxc_cpufreq_init()
The variable mxc_driver references
the function __init mxc_cpufreq_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Richard Zhao <richard.zhao@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jamie Iles [Sat, 17 Dec 2011 13:42:37 +0000 (13:42 +0000)]
ARM: picoxcell: implement watchdog restart
Allow the platform to be restarted by triggering the watchdog to expire
with the shortest possible expiry. This should reset the CPU core and
all on-chip peripherals.
Jamie Iles [Mon, 12 Dec 2011 20:21:39 +0000 (20:21 +0000)]
ARM: picoxcell: move io mappings to common.c
Now that we have lost our machine specific ioremap() we just have one
mapping that covers all peripherals. Move this to common.c to simplify
things a little.
Rajendra Nayak [Wed, 14 Dec 2011 11:55:46 +0000 (17:25 +0530)]
ARM: omap: pass minimal SoC/board data for UART from dt
Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Wed, 14 Dec 2011 11:55:45 +0000 (17:25 +0530)]
omap-serial: Add minimal device tree support
Adapt the driver to device tree and pass minimal platform
data from device tree needed for console boot.
No power management features will be suppported for now
since it requires more tweaks around OCP settings
to toggle forceidle/noidle/smartidle bits and handling
remote wakeup and dynamic muxing.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Wed, 14 Dec 2011 11:55:43 +0000 (17:25 +0530)]
omap-serial: Get rid of all pdev->id usage
With Device tree, pdev->id would no longer be Valid.
Hence get rid of all instances of its usage in the
driver. Device tree support for the driver is added
in subsequent patches.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Fri, 16 Dec 2011 12:50:12 +0000 (05:50 -0700)]
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.
Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().
A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: Kevin Hilman <khilman@ti.com> Acked-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
edited some documentation] Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tero Kristo [Fri, 16 Dec 2011 21:37:00 +0000 (14:37 -0700)]
ARM: OMAP4: PRM: use PRCM interrupt handler
Use the new PRCM interrupt handler code on OMAP4 systems.
The OMAP code will need to be converted to use sparse IRQs for this
to work. Until that time, the following message will appear on boot:
PRCM: failed to allocate irq descs: -12
Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: split this from a previous patch to this patch; call
omap4xxx_prcm_init() during init; write trivial commit log] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Fri, 16 Dec 2011 21:36:59 +0000 (14:36 -0700)]
ARM: OMAP3: pm: use prcm chain handler
PM interrupt handling is now done through the PRCM chain handler. The
interrupt handling logic is also split in two parts, to serve IO and
WKUP events separately. This allows us to handle IO chain events in a
clean way.
Core event code is also changed in accordance to this, as PRCM
interrupt handling is done by independent handlers, and the core
handler should not clear the IO events anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: use pr_err(); combined with portions of earlier patches and
the "do not enable PRCM MPU interrupts manually" patch] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Fri, 16 Dec 2011 21:36:59 +0000 (14:36 -0700)]
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
changes; added kerneldoc] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Fri, 16 Dec 2011 21:36:59 +0000 (14:36 -0700)]
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.
[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: Tero Kristo <t-kristo@ti.com> Cc: Govindraj.R <govindraj.raja@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
improved function documentation; modified to iterate only through dynamic
pads; modified to skip pads where idle mode doesn't enable wakeups; split
patches] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Fri, 16 Dec 2011 21:36:58 +0000 (14:36 -0700)]
ARM: OMAP: PRCM: add suspend prepare / finish support
PRCM chain handler needs to disable forwarding of interrupts during
suspend, because runtime PM is disabled and most of the drivers
are potentially not able to handle interrupts coming at this time.
This patch masks all the PRCM interrupt events if a PRCM interrupt
occurs during suspend, but does not ack them. Once suspend finish
is called, all the masked events will be re-enabled, which causes
immediate PRCM interrupt and handles the postponed event.
The suspend prepare and complete callbacks will be called from
pm34xx.c / pm44xx.c files in the following patches.
The functions defined in this patch should eventually be moved to
suspend->prepare and suspend->finish driver hooks, once the PRCM
chain handler will be made as its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: add kerneldoc, add omap_prcm_irq_setup.saved_mask, add fn
ptrs for save_and_clear_irqen() and restore_irqen()] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Fri, 16 Dec 2011 21:36:58 +0000 (14:36 -0700)]
ARM: OMAP: PRCM: add support for chain interrupt handler
Introduce a chained interrupt handler mechanism for the PRCM
interrupt, so that individual PRCM event can cleanly be handled by
handlers in separate drivers. We do this by introducing PRCM event
names, which are then matched to the particular PRCM interrupt bit
depending on the specific OMAP SoC being used.
PRCM interrupts have two priority levels, high or normal. High priority
is needed for IO event handling, so that we can be sure that IO events
are processed before other events. This reduces latency for IO event
customers and also prevents incorrect ack sequence on OMAP3.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Avinash.H.M <avinashhm@ti.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Govindraj.R <govindraj.raja@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: drop some dead code; use SoC-specific pending IRQ
detection; move code to prm_common.c; add lots of documentation;
remove saved_mask; add OCP barrier on ISR exit; improved error
handling; split out per-SoC initialization to a separate patch] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add PRM functions to test for pending PRM IRQs. This will be used in
a subsequent patch to implement the PRM interrupt handler on the MPU.
Add PRM functions to ensure that all outstanding writes from the MPU
to the PRM IP block have completed before continuing execution. This
will be used in a subsequent patch to ensure that all PRM interrupt
status bits are cleared in the hardware before exiting the ISR.
Normally we would not expose such a low-level function to other code.
But the current implementation of the PRM interrupt code, which uses
the generic IRQ chip code, doesn't give us a choice.
The pending PRM IRQ functions are based on code originally written by
Tero Kristo <t-kristo@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tero Kristo <t-kristo@ti.com>
Govindraj R [Fri, 16 Dec 2011 21:36:58 +0000 (14:36 -0700)]
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
Add API to enable IO pad wakeup capability based on mux pad and
wake_up enable flag available from hwmod_mux initialization.
Use the wakeup_enable flag and enable wakeup capability for the given
pads. Wakeup capability will be enabled/disabled during hwmod idle
transition based on whether wakeup_flag is set or cleared. If the
hwmod is currently idled, and any mux values were changed by
_set_idle_ioring_wakeup(), the SCM PADCTRL registers will be updated.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: rearranged code to limit indentation; cleaned up
function documentation; removed unused non-static functions; modified
to search all hwmod pads, not just dynamic remuxing ones; modified to
update SCM regs if hwmod is currently idle and any pads have changed] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Fri, 16 Dec 2011 21:36:57 +0000 (14:36 -0700)]
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
omap_hwmod_mux() currently only iterates through the dynamic pad list.
This list currently only consists of pads with the
OMAP_DEVICE_MUX_REMUX flag set.
Subsequent patches in this series will cause hwmod mux entries with
the OMAP_DEVICE_MUX_WAKEUP flag set to be changed dynamically, to
control hwmod I/O ring wakeup. For this to work correctly, hwmod mux
entries with the OMAP_DEVICE_MUX_WAKEUP flag set must also be added to
the dynamic pad list. So this patch modifies omap_hwmod_mux_init() to
do so.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Govindraj R <govindraj.raja@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32: Be less strict in matching %lo part of relocation.
sbus: convert drivers/sbus/char/* to use module_platform_driver()
bbc_i2c: Remove unneeded err variable
sparc: Use kmemdup rather than duplicating its implementation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: Check dest prefix length on original route not copied one in rt6_alloc_cow().
sch_gred: should not use GFP_KERNEL while holding a spinlock
ipip, sit: copy parms.name after register_netdevice
ipv6: Fix for adding multicast route for loopback device automatically.
ssb: fix init regression with SoCs
rtl8192{ce,cu,de,se}: avoid problems because of possible ERFOFF -> ERFSLEEP transition
mac80211: fix another race in aggregation start
fsl_pq_mdio: Clean up tbi address configuration
ppp: fix pptp double release_sock in pptp_bind()
net/fec: fix the use of pdev->id
ath9k: fix check for antenna diversity support
batman-adv: delete global entry in case of roaming
batman-adv: in case of roaming mark the client with TT_CLIENT_ROAM
Bluetooth: Correct version check in hci_setup
btusb: fix a memory leak in btusb_send_frame()
Bluetooth: bnep: Fix module reference
Bluetooth: cmtp: Fix module reference
Bluetooth: btmrvl: support Marvell Bluetooth device SD8797
Linus Torvalds [Fri, 16 Dec 2011 20:15:50 +0000 (12:15 -0800)]
Merge branches 'for-linus' and 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: unplug every once and a while
Btrfs: deal with NULL srv_rsv in the delalloc inode reservation code
Btrfs: only set cache_generation if we setup the block group
Btrfs: don't panic if orphan item already exists
Btrfs: fix leaked space in truncate
Btrfs: fix how we do delalloc reservations and how we free reservations on error
Btrfs: deal with enospc from dirtying inodes properly
Btrfs: fix num_workers_starting bug and other bugs in async thread
BTRFS: Establish i_ops before calling d_instantiate
Btrfs: add a cond_resched() into the worker loop
Btrfs: fix ctime update of on-disk inode
btrfs: keep orphans for subvolume deletion
Btrfs: fix inaccurate available space on raid0 profile
Btrfs: fix wrong disk space information of the files
Btrfs: fix wrong i_size when truncating a file to a larger size
Btrfs: fix btrfs_end_bio to deal with write errors to a single mirror
* 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: lower the dirty balance poll interval
Linus Torvalds [Fri, 16 Dec 2011 19:27:56 +0000 (11:27 -0800)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
drm/i915: enable semaphores on per-device defaults
drm/i915: don't set unpin_work if vblank_get fails
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
iommu: Export intel_iommu_enabled to signal when iommu is in use
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
drm/i915: prevent division by zero when asking for chipset power
drm/i915: add PCH info to i915_capabilities
drm/i915: set the right SDVO transcoder for CPT
drm/i915: no-lvds quirk for ASUS AT5NM10T-I
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
drm/i915: Hook up Ivybridge eDP
drm/i915: add multi-threaded forcewake support
Linus Torvalds [Fri, 16 Dec 2011 19:14:42 +0000 (11:14 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: HDA: Use LPIB Position fix for Intel SCH Poulsbo
ALSA: hda: fix mute led polarity for HP laptops with buggy BIOS
ALSA: HDA: Set position fix to LPIB for an Atom/Poulsbo based device
ASoC: Fix hx4700 error handling to free gpios if snd_soc_register_card fails
ASoC: WM8958: correctly show firmware magic on mismatch
ASoC: mxs: Add appropriate MODULE_ALIAS()
ASoC: mxs: Add missing MODULE_LICENSE("GPL")
ASoC: Fix WM8996 24.576MHz clock operation
ASoC: Include linux/module.h for smdk2443_wm9710
ASoC: Fix a typo in jive_wm8750
ASoC: Fix build dependency for SND_SOC_JZ4740_CODEC
ASoC: Include linux/io.h for jz4740 codec
Linus Torvalds [Fri, 16 Dec 2011 19:13:49 +0000 (11:13 -0800)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: Fix DA9052 GPIO build errors.
gpio: mpc8xxx: don't allow input-only pins to be output for MPC5121
gpio-ml-ioh: Add the irq_disable/irq_enable hooks for ml-ioh irq chip
gpio-ml-ioh: fix a bug in the interrupt handler
gpio: pl061: drop extra check for NULL platform_data
Linus Torvalds [Fri, 16 Dec 2011 18:07:50 +0000 (10:07 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: rx51: fix USB
ARM: OMAP: mcbsp: Fix possible memory corruption
arm/imx: fix power button on imx51 babbage board
ARM: imx: fix cpufreq build errors
ARM: mx5: add __initconst for fec pdata
MXC PWM: should active during DOZE/WAIT/DBG mode
ARM: EXYNOS: Fix build error without CONFIG_LOCAL_TIMERS
ARM: EXYNOS: Fix for stall in case of cpu hotplug or sleep
ARM: S5PV210: Set 1000ns as PWM backlight period on SMDKV210
ARM: SAMSUNG: remove duplicated header include
Wu Fengguang [Fri, 16 Dec 2011 17:32:57 +0000 (12:32 -0500)]
btrfs: lower the dirty balance poll interval
Tests show that the original large intervals can easily make the dirty
limit exceeded on 100 concurrent dd's. So adapt to as large as the
next check point selected by the dirty throttling algorithm.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Eric Anholt <eric@anholt.net> Tested-by: Eric Anholt <eric@anholt.net> Tested-by: Dirk Hohndel <hohndel@infradead.org> Signed-off-by: Keith Packard <keithp@keithp.com>
Eugeni Dodonov [Sat, 10 Dec 2011 01:16:37 +0000 (17:16 -0800)]
drm/i915: enable semaphores on per-device defaults
This adds a default setting for semaphores parameter, and enables
semaphores by default on IVB.
For now, as semaphores interaction with VTd causes random issues on
SNB, we do not enable them by default. But they can still be enabled
via the semaphores=1 kernel parameter.
v2: enables semaphores on SNB when IO remapping is disabled, with base
on Keith Packard patch.
CC: Daniel Vetter <daniel.vetter@ffwll.ch> CC: Ben Widawsky <ben@bwidawsk.net> CC: Keith Packard <keithp@keithp.com> CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42696
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=40564
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38862 Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Mon, 29 Aug 2011 16:45:28 +0000 (09:45 -0700)]
drm/i915: don't set unpin_work if vblank_get fails
This fixes a race where we may try to finish a page flip and decrement
the refcount even if our vblank_get failed and we ended up with a
spurious flip pending interrupt.
Keith Packard [Thu, 17 Nov 2011 06:24:52 +0000 (22:24 -0800)]
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
RC6 should always work on IVB, and should work on SNB whenever IO
remapping is disabled. RC6 never works on Ironlake. Make the default
value for the parameter follow these guidelines. Setting the value
to either 0 or 1 will force the specified behavior.
Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567 Cc: Ted Phelps <phelps@gnusto.com> Cc: Peter <pab1612@gmail.com> Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz> Cc: Andrew Lutomirski <luto@mit.edu>
Eugeni Dodonov [Wed, 23 Nov 2011 18:42:14 +0000 (16:42 -0200)]
iommu: Export intel_iommu_enabled to signal when iommu is in use
In i915 driver, we do not enable either rc6 or semaphores on SNB when dmar
is enabled. The new 'intel_iommu_enabled' variable signals when the
iommu code is in operation.
Cc: Ted Phelps <phelps@gnusto.com> Cc: Peter <pab1612@gmail.com> Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz> Cc: Andrew Lutomirski <luto@mit.edu> CC: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Mon, 20 Jun 2011 13:45:50 +0000 (14:45 +0100)]
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216 Signed-off-by: Keith Packard <keithp@keithp.com>
Eugeni Dodonov [Thu, 10 Nov 2011 15:55:15 +0000 (13:55 -0200)]
drm/i915: prevent division by zero when asking for chipset power
This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.
The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done
This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.
This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Keith Packard <keithp@keithp.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Paulo Zanoni [Fri, 14 Oct 2011 21:17:41 +0000 (18:17 -0300)]
drm/i915: add PCH info to i915_capabilities
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Paulo Zanoni [Fri, 14 Oct 2011 21:16:22 +0000 (18:16 -0300)]
drm/i915: set the right SDVO transcoder for CPT
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272 Cc: stable@kernel.org Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com>
Nicolas Ferre [Thu, 24 Nov 2011 21:21:14 +0000 (22:21 +0100)]
net/at91_ether: use gpio_is_valid for phy IRQ line
Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.
For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log