Bjorn Helgaas [Tue, 14 Jun 2011 19:04:35 +0000 (13:04 -0600)]
PCI: fold pci_calc_resource_flags() into decode_bar()
decode_bar() and pci_calc_resource_flags() both looked at the PCI BAR
type information, and it's simpler to just do it all in one place.
decode_bar() sets IORESOURCE_IO, IORESOURCE_MEM, and IORESOURCE_MEM_64
as appropriate, so res->flags contains all the information pci_bar_type
does, so we don't need to test the pci_bar_type return value.
decode_bar() used to return pci_bar_type, which we no longer need. We
can simplify it a bit by returning the struct resource flags rather than
updating them internally.
In pci_update_resource(), there's no need to decode the BAR type bits
again; we can just test for IORESOURCE_MEM_64 directly.
Bjorn Helgaas [Tue, 14 Jun 2011 19:04:29 +0000 (13:04 -0600)]
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952 Reported-by: Jan Zwiegers <jan@radicalsystems.co.za> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jon Mason [Tue, 28 Jun 2011 23:26:25 +0000 (18:26 -0500)]
PCI: correct pcie_set_readrq write size
When setting the PCI-E MRRS, pcie_set_readrq queries the current
settings via a pci_read_config_word call but writes the modified result
via a pci_write_config_dword. This results in writing 16 more bits than
were queried.
Also, the function description comment is slightly incorrect.
Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI: pciehp: change wait time for valid configuration access
Naoki Yanagimoto reported that configuration read on some hot-added
PCIe device returns invalid value. This patch fixes this problem.
According to the PCIe spec, software must wait for at least 1 second
to judge if the hot-added device is broken after Data Link Layer State
Changed Event. This patch changes pciehp driver to wait for 1 second
after the Data Link Layer State Changed Event is detected before
initiating a configuration access instead of 100 ms.
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
Commit 6e8af08dfa40b747002207d3ce8e8b43a050d99f enables pci=bfsort on
future Dell systems. But the identification string 'Dell System' matches
on already existing whitelist, which do not have SMBIOS type 0xB1,
causing pci=bfsort not being set on existing whitelist.
This patch fixes the regression by moving the type 0xB1 check beyond the
existing whitelist so that existing whitelist is walked before.
Chris Wright [Wed, 13 Jul 2011 17:14:33 +0000 (10:14 -0700)]
PCI: ARI is a PCIe v2 feature
The function pci_enable_ari() may mistakenly set the downstream port
of a v1 PCIe switch in ARI Forwarding mode. This is a PCIe v2 feature,
and with an SR-IOV device on that switch port believing the switch above
is ARI capable it may attempt to use functions 8-255, translating into
invalid (non-zero) device numbers for that bus. This has been seen
to cause Completion Timeouts and general misbehaviour including hangs
and panics.
Cc: stable@kernel.org Acked-by: Don Dutile <ddutile@redhat.com> Tested-by: Don Dutile <ddutile@redhat.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This code uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it wasn't converted by commit 44c10138fd4bbc ("PCI: Change all
drivers to use pci_device->revision") before being moved to arch/x86/...
Ralf Baechle [Fri, 10 Jun 2011 14:30:21 +0000 (15:30 +0100)]
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com> Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com> Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net> Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-alpha@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-pci@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: linux-tegra@vger.kernel.org Cc: sparclinux@vger.kernel.org Cc: x86@kernel.org Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Sergei Shtylyov [Wed, 13 Jul 2011 15:20:14 +0000 (19:20 +0400)]
PCI hotplug: cpqphp: use pci_dev->vendor
The driver reads PCI vendor ID from the PCI configuration register while it is
already stored by the PCI subsystem in the 'vendor' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Sergei Shtylyov [Wed, 13 Jul 2011 15:21:25 +0000 (19:21 +0400)]
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jan Beulich [Fri, 22 Jul 2011 07:13:05 +0000 (08:13 +0100)]
x86/PCI: config space accessor functions should not ignore the segment argument
Without this change, the majority of the raw PCI config space access
functions silently ignore a non-zero segment argument, which is
certainly wrong.
Apart from pci_direct_conf1, all other non-MMCFG access methods get
used only for non-extended accesses (i.e. assigned to raw_pci_ops
only). Consequently, with the way raw_pci_{read,write}() work, it would
be a coding error to call these functions with a non-zero segment (with
the current call flow this cannot happen afaict).
The access method 1 accessor, as it can be used for extended accesses
(on AMD systems) instead gets checks added for the passed in segment to
be zero. This would be the case when on such a system having multiple
PCI segments (don't know whether any exist in practice) MMCFG for some
reason is not usable, and method 1 gets selected for doing extended
accesses. Rather than accessing the wrong device's config space, the
function will now error out.
v2: Convert BUG_ON() to WARN_ON(), and extend description as per Ingo's
request.
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
'pci_obff_signal_type' is passed between drivers and the kernel API.
This patch explicitly assigns values to the enumeration type's constants
which aids in detecting any future changes or additions that would break
the kernel's ABI.
x86/PCI: reduce severity of host bridge window conflict warnings
Host bridge windows are top-level resources, so if we find a host bridge
window conflict, it's probably with a hard-coded legacy reservation.
Moving host bridge windows is theoretically possible, but we don't support
it; we just ignore windows with conflicts, and it's not worth making this
a user-visible error.
Tiejun Chen [Thu, 2 Jun 2011 03:02:50 +0000 (11:02 +0800)]
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
When hot-plugging a root bridge, we always prevent assigning a bus number
that already exists. This makes sure we don't step over an existing bus.
But sometimes we only remove PCI device in PCI hieratchy of OS, i,e.
echo 1 > /sys/bus/pci/devices/.../remove
but actually don't hotplug this device out the platform, so in this case
we still should re-scan this bus to enumerate this device when re-scanning
PCI again.
Huang Ying [Tue, 17 May 2011 08:08:37 +0000 (16:08 +0800)]
PCI: PCIe AER: add aer_recover_queue
In addition to native PCIe AER, now APEI (ACPI Platform Error
Interface) GHES (Generic Hardware Error Source) can be used to report
PCIe AER errors too. To add support to APEI GHES PCIe AER recovery,
aer_recover_queue is added to export the recovery function in native
PCIe AER driver.
Recoverable PCIe AER errors are reported via NMI in APEI GHES. Then
APEI GHES uses irq_work to delay the error processing into an IRQ
handler. But PCIe AER recovery can be very time-consuming, so
aer_recover_queue, which can be used in IRQ handler, delays the real
recovery action into the process context, that is, work queue.
Shaohua Li [Fri, 27 May 2011 06:59:39 +0000 (14:59 +0800)]
x86/PCI: select direct access mode for mmconfig option
Direct access is needed in mmconf mode too. There are two reasons:
1. we need it to access first 256 bytes. We have bug before that
using mmconf to access pci config space hangs system (when
resizing BARs), so we use type1 config for legacy config space.
2. when doing mmconfg bar checking, we need access ACPI _CRS,
which might access PCI config space.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Thomas Renninger [Fri, 27 May 2011 08:23:00 +0000 (10:23 +0200)]
PCI hotplug: Rename is_ejectable which also exists in dock.c
While it's declared static, etags points you to the wrong function
in drivers/acpi/dock.c and acpiphp_glue.c for example also makes
use of some (exported..) functions from this file.
If you trust etags and oversee the static declaration (what happened
to me) one gets totally confused...
Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ram Pai [Thu, 7 Jul 2011 18:19:10 +0000 (11:19 -0700)]
PCI: conditional resource-reallocation through kernel parameter pci=realloc
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix regression occurring during device removal
USB: fsl_udc_core: fix build breakage when building for ARM arch
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Add Makefile and Kconfig Entries for tps65911 comparator
mfd: Fix build error for tps65911-comparator.c
Revert "mfd: Add omap-usbhs runtime PM support"
input: pmic8xxx-pwrkey: Do not use mfd_get_data()
input: pmic8xxx-keypad: Do not use mfd_get_data()
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix sync and dio writes across stripe boundaries
libceph: fix page calculation for non-page-aligned io
ceph: fix page alignment corrections
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
hfsplus: Fix double iput of the same inode in hfsplus_fill_super()
hfsplus: add missing call to bio_put()
Axel Lin [Thu, 23 Jun 2011 02:17:43 +0000 (10:17 +0800)]
mfd: Fix build error for tps65911-comparator.c
Fix below build error:
CC drivers/mfd/tps65911-comparator.o
drivers/mfd/tps65911-comparator.c: In function 'tps65911_comparator_probe':
drivers/mfd/tps65911-comparator.c:131: error: 'struct tps65910_platform_data' has no member named 'vmbch_threshold'
drivers/mfd/tps65911-comparator.c:137: error: 'struct tps65910_platform_data' has no member named 'vmbch2_threshold'
make[2]: *** [drivers/mfd/tps65911-comparator.o] Error 1
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Oops are produced during initialization of ehci and ohci
drivers. This is because the run time pm apis are used by
the driver but the corresponding hwmod structures and
initialization is not merged. hence revering back the
commit id 7e6502d577106fb5b202bbaac64c5f1b065e6daa
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Reported-by: Luciano Coelho <coelho@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Merge branch 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
Commits 71c29bd5c235 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980ce01 ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.
However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.
Add the missing checks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c. - Roland ] Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Fri, 1 Jul 2011 10:25:24 +0000 (12:25 +0200)]
AT91: Change nand buswidth logic to match hardware default configuration
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Max Baldwin <archerseven@gmail.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jeff Skirvin [Fri, 1 Jul 2011 20:03:44 +0000 (13:03 -0700)]
isci: Device reset should request sas_phy_reset(phy, true)
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 1 Jul 2011 18:41:21 +0000 (11:41 -0700)]
isci: cleanup silicon revision detection
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 1 Jul 2011 02:14:33 +0000 (19:14 -0700)]
isci: retire scic_sds_ and scic_ prefixes
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_. The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.
Also unwind the 'sds1' out of the parameter structs.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 1 Jul 2011 00:38:32 +0000 (17:38 -0700)]
isci: unify isci_host and scic_sds_controller
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost). Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 29 Jun 2011 20:09:25 +0000 (13:09 -0700)]
isci: unify isci_port and scic_sds_port
Remove the distinction between these two implementations and unify on
isci_port (local instances named iport). The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 0815632 "isci: unify remote_device stop_handlers" introduced the
possibility that not all requests get terminated if we reach the
request_count. Now that we properly reference count devices we don't
need this self-defense and can do the straightforward scan of all active
requests.
Reported-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Acked-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Tue, 28 Jun 2011 22:05:53 +0000 (15:05 -0700)]
isci: unify isci_phy and scic_sds_phy
They are one in the same object so remove the distinction. The near
duplicate fields (owning_port, and isci_port) will be cleaned up
after the scic_sds_port isci_port unification.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Mon, 27 Jun 2011 21:57:03 +0000 (14:57 -0700)]
isci: unify isci_request and scic_sds_request
They are one in the same object so remove the distinction. The near
duplicate fields (owning_controller, and isci_host) will be cleaned up
after the scic_sds_contoller isci_host unification.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 17 Jun 2011 21:18:39 +0000 (14:18 -0700)]
isci: preallocate requests
the dma_pool interface is optimized for object_size << page_size which
is not the case with isci_request objects and the dma_pool routines show
up in the top of the profile.
The old io_request_table which tracked whether tci slots were in-flight
or not is replaced with an IREQ_ACTIVE flag per request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Tue, 28 Jun 2011 20:47:09 +0000 (13:47 -0700)]
isci: unify can_queue tracking on the tci_pool, uplevel tag assignment
The tci_pool tracks our outstanding command slots which are also the 'index'
portion of our tags. Grabbing the tag early in ->lldd_execute_task let's us
drop the isci_host_can_queue() and ->was_tag_assigned_by_user infrastructure.
->was_tag_assigned_by_user required the task context to be duplicated in
request-local buffer. With the tci established early we can build the
task_context directly into its final location and skip a memcpy.
With the task context buffer at a known address at request construction we
have the opportunity/obligation to also fix sgl handling. This rework feels
like it belongs in another patch but the sgl handling and task_context are too
intertwined.
1/ fix the 'ab' pair embedded in the task context to point to the 'cd' pair in
the task context (previously we were prematurely linking to the staging
buffer).
2/ fix the broken iteration of pio sgls that assumes all sgls are relative to
the request, and does a dangerous looking reverse lookup of physical
address to virtual address.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jeff Skirvin [Fri, 24 Jun 2011 00:09:02 +0000 (17:09 -0700)]
isci: Terminate dev requests on FIS err bit rx in NCQ
When the remote device transitions to a not-ready state because of
an NCQ error condition, all outstanding requests to that device
are terminated and completed to libsas on the normal path. The
device then waits for a READ LOG EXT command to issue on the task
management path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Maciej Patelczyk [Tue, 21 Jun 2011 22:03:13 +0000 (22:03 +0000)]
isci: possible buffer overflow in isci_parse_oem_parameters fixed
scu_index is a parameter of isci_parse_eom_parameters and is an index
in controller table. There is a check: scu_index > SCI_MAX_CONTROLLERS
which is insufficient and should be: scu_index >= SCI_MAX_CONTROLLERS.
scu_index is used as an index in the table which size is
SCI_MAX_CONTROLLERS.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Tue, 21 Jun 2011 23:23:03 +0000 (16:23 -0700)]
isci: fix isci_task_execute_tmf completion
1/ fix the timeout for wait_for_completion_timeout
2/ In the tmf timeout case we need to wait for our termination callback
3/ Once the request is successfully started it will be freed according to the
normal lifetime for requests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Thu, 16 Jun 2011 23:59:56 +0000 (16:59 -0700)]
isci: fix support for arbitrarily large smp requests
Instead of duplicating the smp request buffer reuse the one provided by
libsas. This future proofs the driver to support arbitrarily large smp
requests, and shrinks the request structure size by ~700 bytes.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 17 Jun 2011 00:20:35 +0000 (17:20 -0700)]
isci: fix smp response frame overrun
Due to a typo we currently copy way too much when copying over the
response data, but since a request is likely backed by a full page
allocation we don't corrupt live data.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Thu, 16 Jun 2011 18:26:12 +0000 (11:26 -0700)]
isci: kill isci_remote_device_change_state()
Now that "stopping/stopped" are one in the same and signalled by a NULL device
pointer the rest of the device status infrastructure can be removed (->status
and ->state_lock). The "not ready for i/o state" is replaced with a state
flag, and is evaluated under scic_lock so that we don't see transients from
taking the device reference to submitting the i/o.
This also fixes a potential leakage of can_queue slots in the rare case that
SAS_TASK_ABORTED is set at submission.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Tue, 14 Jun 2011 00:39:44 +0000 (17:39 -0700)]
isci: atomic device lookup and reference counting
We have unsafe references to remote devices that are notified to
disappear at lldd_dev_gone. In order to clean this up we need a single
canonical source for device lookups and stable references once a lookup
succeeds. Towards that end guarantee that domain_device.lldd_dev is
NULL as soon as we start the process of stopping a device. Any code
path that wants to safely lookup a remote device must do so through
task->dev->lldd_dev (isci_lookup_device()).
For in-flight references outside of scic_lock we need reference counting
to ensure that the device is not recycled before we are done with it.
Simplify device back references to just scic_sds_request.target_device
which is now the only permissible internal reference that is maintained
relative to the reference count.
There were two occasions where we wanted new i/o's to be treated as
SAS_TASK_UNDELIVERED but where the domain_dev->lldd_dev link is still
intact. Introduce a 'gone' flag to prevent i/o while waiting for libsas
to take action on the port down event.
One 'core' leftover is that we currently call
scic_remote_device_destruct() from isci_remote_device_deconstruct()
which is called when the 'core' says the device is stopped. It would be
more natural for the final put to trigger
isci_remote_device_deconstruct() but this implementation is deferred as
it requires other changes.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 15 Jun 2011 18:11:03 +0000 (11:11 -0700)]
isci: fix ssp response iu buffer size in isci_tmf
In isci_task_request_complete() we save the response/sense data from the
command. Make sure isci_tmf has enough space to hold the full response.
[ it does not look like we actually use this data, and
response_data_len/sense_data_len should be specifying the byte count,
in any event do the simple fix first so we don't corrupt memory ]
Reported-by: Adam Gruchala <adam.gruchala@intel.com> Tested-by: Edmund Nadolski <edmund.nadolski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Mon, 13 Jun 2011 07:51:30 +0000 (00:51 -0700)]
isci: cleanup request allocation
Rather than return an error code and update a pointer that was passed by
reference just return the request object directly (or null if allocation
failed).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Thu, 9 Jun 2011 23:04:28 +0000 (16:04 -0700)]
isci: cleanup/optimize queue increment macros
Every single i/o or event completion incurs a test and branch to see if
the cycle bit changed. For power-of-2 queue sizes the cycle bit can be
read directly from the rollover of the queue pointer.
Likely premature optimization, but the hidden if() and hidden
assignments / side-effects in the macros were already asking to be
cleaned up.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Thu, 9 Jun 2011 18:06:58 +0000 (11:06 -0700)]
isci: cleanup tag macros
A tag is a 16 bit number where the upper four bits is a sequence number
and the remainder is the task context index (tci). Sanitize the macro
names and shave 256-bytes out of scic_sds_controller by reducing the size of
io_request_sequence.
Dan Williams [Wed, 8 Jun 2011 01:50:55 +0000 (18:50 -0700)]
isci: cleanup/optimize pool implementation
The circ_buf macros are ~6% faster, as measured by perf, because they take
advantage of power-of-two math assumptions i.e. no test and branch for
rollover. Their semantics are clearer than the hidden side effects in pool.h
(like sci_pool_get() which hides an assignment).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Mon, 20 Jun 2011 22:11:22 +0000 (15:11 -0700)]
isci: fix isci_terminate_pending() list management
Walk through the list of pending requests being careful to consider that
multiple requests can be terminated when the lock is dropped (i.e.
invalidating the 'next' reference established by
list_for_each_entry_safe).
Also noticed that all callers to isci_terminate_pending_requests()
specifying terminating, so just drop the parameter.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the situation where a termination of an I/O times-out,
make sure that the linkage from the request to the task
is severed completely. Also make sure that the selection
of tasks to terminate occurs under scic_lock.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jeff Skirvin [Mon, 20 Jun 2011 21:09:06 +0000 (14:09 -0700)]
isci: Add decode for SMP request retry error condition
There are situations with slow expanders in which a first attempt
to execute an SMP request will fail with a timeout. Immediate
subsequent retries will generally succeed. This change makes sure
SMP I/O failures are immediately failed to libsas so that retries
happen with no discovery process timeout delay.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jeff Skirvin [Tue, 21 Jun 2011 19:16:33 +0000 (12:16 -0700)]
isci: filter broadcast change notifications during SMP phy resets
When resetting a sata device in the domain we have seen occasions where
libsas prematurely marks a device gone in the time it takes for the
device to re-establish the link. This plays badly with software raid
arrays. Other libsas drivers have non-uniform delays in their reset
handlers to try to cover this condition, but not sufficient to close the
hole. Given that a sata device can take many seconds to recover we
filter bcns and poll for the device reattach state before notifying
libsas that the port needs the domain to be rediscovered. Once this has
been proven out at the lldd level we can think about uplevelling this
feature to a common implementation in libsas.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
[ use kzalloc instead of kmem_cache ] Signed-off-by: Dave Jiang <dave.jiang@intel.com>
[ use eventq and time macros ] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 1 Jun 2011 23:00:01 +0000 (16:00 -0700)]
isci: remove 'min memory' infrastructure
The old 'core' had aspirations of running in severely memory constrained
environments like bios option-rom, it's not needed for Linux and gets in
the way of other cleanups (like unifying/reducing the number of structure
members in scic_sds_controller/isci_host).
This also fixes a theoretical bug in that the driver would blindly override
the silicon advertised limits for number of ports, task contexts, and remote
node contexts.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adam Gruchala [Wed, 1 Jun 2011 22:31:03 +0000 (22:31 +0000)]
isci: Added support for C0 to SCU Driver
C0 silicon updates the pci revision id and requires new AFE parameters
for phy signal integrity. Support for previous silicon revisions is
deprecated (it's also broken for the theoretical case of multiple
controllers at different silicon revisions, all the more reason to get
it removed as soon as possible)
Signed-off-by: Adam Gruchala <adam.gruchala@intel.com>
[fixed up deprecated silicon support] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Edmund Nadolski [Thu, 2 Jun 2011 00:10:50 +0000 (00:10 +0000)]
isci: additional state machine cleanup
Additional state machine cleanups:
o Remove static functions sci_state_machine_exit_state() and
sci_state_machine_enter_state()
o Combines sci_base_state_machine_construct() and
sci_base_state_machine_start() into a single function,
sci_init_sm()
o Remove sci_base_state_machine_stop() which is unused.
o Kill state_machine.[ch]
Signed-off-by: Edmund Nadolski <edmund.nadolski@intel.com>
[fixed too large to inline functions] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Edmund Nadolski [Thu, 2 Jun 2011 00:10:43 +0000 (00:10 +0000)]
isci: state machine cleanup
This cleans up several areas of the state machine mechanism:
o Rename sci_base_state_machine_change_state to sci_change_state
o Remove sci_base_state_machine_get_state function
o Rename 'state_machine' struct member to 'sm' in client structs
o Shorten the name of request states
o Shorten state machine state names as follows:
SCI_BASE_CONTROLLER_STATE_xxx to SCIC_xxx
SCI_BASE_PHY_STATE_xxx to SCI_PHY_xxx
SCIC_SDS_PHY_STARTING_SUBSTATE_xxx to SCI_PHY_SUB_xxx
SCI_BASE_PORT_STATE_xxx to SCI_PORT_xxx and
SCIC_SDS_PORT_READY_SUBSTATE_xxx to SCI_PORT_SUB_xxx
SCI_BASE_REMOTE_DEVICE_STATE_xxx to SCI_DEV_xxx
SCIC_SDS_STP_REMOTE_DEVICE_READY_SUBSTATE_xxx to SCI_STP_DEV_xxx
SCIC_SDS_SMP_REMOTE_DEVICE_READY_SUBSTATE_xxx to SCI_SMP_DEV_xxx
SCIC_SDS_REMOTE_NODE_CONTEXT_xxx_STATE to SCI_RNC_xxx
Signed-off-by: Edmund Nadolski <edmund.nadolski@intel.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dave Jiang [Wed, 25 May 2011 02:21:57 +0000 (02:21 +0000)]
isci: removing the kmalloc in smp request construct
It doesn't look like there is any reason to do a kmalloc. We can do the
byte swap in place and avoid the allocation. This allow us to remove
a kmalloc and a memcpy.
Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
projects / linux-beck.git / log