Ralf Baechle [Wed, 11 Jan 2012 14:37:16 +0000 (15:37 +0100)]
MIPS: Set default pci cache line size.
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Manuel Lauss [Thu, 8 Dec 2011 10:42:16 +0000 (10:42 +0000)]
MIPS: Alchemy: db1200: Improve PB1200 detection.
The PB1200 has the CPLD located at an address which on the DB1200 is
RAM; reading the Board-ID sometimes results in a PB1200 being detected
instead (especially during reboots after long uptimes).
On the other hand, the address of the DB1200's CPLD is hosting Flash
chips on the PB1200. Test for the DB1200 first and additionally do a
quick write-test to the hexleds register to make sure we're writing
to the CPLD.
Manuel Lauss [Thu, 8 Dec 2011 10:42:16 +0000 (10:42 +0000)]
MIPS: Alchemy: merge Au1000 and Au1300-style IRQ controller code.
With a generic plat_irq_dispatch (for Alchemy at least) code for both
interrupt controller types can coexist in a single kernel image and be
autodetected at runtime.
Manuel Lauss [Thu, 8 Dec 2011 10:42:15 +0000 (10:42 +0000)]
net/irda: convert au1k_ir to platform driver.
Moderate driver cleanup:
convert to platform driver, get rid of board-specific code.
Driver loads and runs on a DB1100 board. But since I have no other
IrDA hardware to exchange data with I can't say whether it really sends
and receives.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: netdev@vger.kernel.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2877/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Thu, 8 Dec 2011 10:42:10 +0000 (10:42 +0000)]
MTD: nand: make au1550nd.c a platform_driver
Transform the au1550nd.c driver into a platform_driver and hook it
up in the PB1550 board (gen_nand works fine on the DB1550, but since
I don't have a PB1550 to test this driver stays for now).
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Cc: linux-mtd@lists.infradead.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2875/
Patchwork: https://patchwork.linux-mips.org/patch/3160/ Acked-by: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jayachandran C [Wed, 16 Nov 2011 00:21:29 +0000 (00:21 +0000)]
MIPS: Netlogic: Merge some of XLR/XLP wakup code
Create a common NMI and reset handler in smpboot.S and use this for
both XLR and XLP. In the earlier code, the woken up CPUs would
busy wait until released, switch this to wakeup by NMI.
The initial wakeup code or XLR and XLP are differ since they are
started from different bootloaders (XLP from u-boot and XLR from
netlogic bootloader). But in both platforms the woken up CPUs wait
and are released by sending an NMI.
Add support for starting XLR and XLP in 1/2/4 threads per core.
Jayachandran C [Wed, 16 Nov 2011 00:21:28 +0000 (00:21 +0000)]
MIPS: Netlogic: Add XLP platform files for XLP SoC
- Update common files to support XLP.
- Add arch/mips/include/asm/netlogic/xlp-hal for register definitions
and access macros
- Add arch/mips/netlogic/xlp/ for XLP specific files.
Jayachandran C [Wed, 16 Nov 2011 00:21:20 +0000 (00:21 +0000)]
MIPS: Netlogic: XLP CPU support.
Add support for Netlogic's XLP MIPS SoC. This patch adds:
* XLP processor ID in cpu_probe.c and asm/cpu.h
* XLP case to asm/module.h
* CPU_XLP case to mm/tlbex.c
* minor change to r4k cache handling to ignore XLP secondary cache
* XLP cpu overrides to mach-netlogic/cpu-feature-overrides.h
Jayachandran C [Fri, 11 Nov 2011 11:38:29 +0000 (17:08 +0530)]
MIPS: Netlogic: Move code common with XLP to common/
- Move code that can be shared with XLP (irq.c, smp.c, time.c and
xlr_console.c) to arch/mips/netlogic/common
- Add asm/netlogic/haldefs.h and asm/netlogic/common.h for common and
io functions shared with XLP
- remove type 'nlm_reg_t *' and use uint64_t for mmio offsets
- Move XLR specific code in smp.c to xlr/wakeup.c
- Move XLR specific PCI code from irq.c to mips/pci/pci-xlr.c
- Provide API for pic functions called from common/irq.c
Deng-Cheng Zhu [Mon, 21 Nov 2011 19:28:47 +0000 (03:28 +0800)]
MIPS/Perf-events: Remove pmu and event state checking in validate_event()
Why removing pmu checking:
Since 3.2-rc1, when arch level event init is called, the event is already
connected to its PMU. Also, validate_event() is _only_ called by
validate_group() in event init, so there is no need of checking or
temporarily assigning event pmu during validate_group().
Why removing event state checking:
Events could be created in PERF_EVENT_STATE_OFF (attr->disabled == 1), when
these events go through this checking, validate_group() does dummy work.
But we do need to do group scheduling emulation for them in event init.
Again, validate_event() is _only_ called by validate_group().
When initialising a PMU, there is a check to protect against races with
other CPUs filling all of the available event slots. Since armpmu_add
checks that an event can be scheduled, we do not need to do this at
initialisation time. Furthermore the current code is broken because it
assumes that atomic_inc_not_zero will unconditionally increment
active_counts and then tries to decrement it again on failure.
This patch removes the broken, redundant code.
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: David Daney <david.daney@cavium.com> Cc: Eyal Barzilay <eyal@mips.com> Cc: Zenon Fortuna <zenon@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/3106/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Deng-Cheng Zhu [Mon, 21 Nov 2011 19:28:45 +0000 (03:28 +0800)]
MIPS/Perf-events: Don't do validation on raw events
MIPS licensees may want to modify performance counters to count extra
events. Also, now that the user is working on raw events, the manual is
being used for sure. And feeding unsupported events shouldn't cause
hardware failure and the like.
[ralf@linux-mips.org: performance events also being used in internal
performance evaluation and have a tendency to change as the micro-
architecture evolves, even for minor revisions that may not be
distinguishable by PrID. It's not very practicable to maintain a list
of all events and there is no real benefit.]
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: David Daney <david.daney@cavium.com> Cc: Eyal Barzilay <eyal@mips.com> Cc: Zenon Fortuna <zenon@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/3107/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maneesh Soni [Tue, 8 Nov 2011 11:38:26 +0000 (17:08 +0530)]
MIPS Kprobes: Support branch instructions probing
This patch provides support for kprobes on branch instructions. The branch
instruction at the probed address is actually emulated and not executed
out-of-line like other normal instructions. Instead the delay-slot instruction
is copied and single stepped out of line.
At the time of probe hit, the original branch instruction is evaluated
and the target cp0_epc is computed similar to compute_retrun_epc(). It
is also checked if the delay slot instruction can be skipped, which is
true if there is a NOP in delay slot or branch is taken in case of
branch likely instructions. Once the delay slot instruction is single
stepped the normal execution resume with the cp0_epc updated the earlier
computed cp0_epc as per the branch instructions.
Signed-off-by: Maneesh Soni <manesoni@cisco.com> Signed-off-by: Victor Kamensky <kamensky@cisco.com> Cc: David Daney <david.daney@cavium.com> Cc: ananth@in.ibm.com Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2914/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maneesh Soni [Tue, 8 Nov 2011 11:37:11 +0000 (17:07 +0530)]
MIPS Kprobes: Refactor branch emulation
This patch refactors MIPS branch emulation code so as to allow skipping
delay slot instruction in case of branch likely instructions when branch is
not taken. This is useful for keeping the code common for use cases like
kprobes where one would like to handle the branch instructions keeping the
delay slot instuction also in picture for branch likely instructions. Also
allow emulation when instruction to be decoded is not at pt_regs->cp0_epc
as in case of kprobes where pt_regs->cp0_epc points to the breakpoint
instruction.
The patch also exports the function for modules.
Signed-off-by: Maneesh Soni <manesoni@cisco.com> Signed-off-by: Victor Kamensky <kamensky@cisco.com> Cc: David Daney <david.daney@cavium.com> Cc: ananth@in.ibm.com Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2913/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maneesh Soni [Tue, 8 Nov 2011 11:34:54 +0000 (17:04 +0530)]
MIPS Kprobes: Fix OOPS in arch_prepare_kprobe()
This patch fixes the arch_prepare_kprobe() on MIPS when it tries to find the
instruction at the previous address to the probed address. The oops happens
when the probed address is the first address in a kernel module and there is
no previous address. The patch uses probe_kernel_read() to safely read the
previous instruction.
Yong Zhang [Tue, 22 Nov 2011 14:38:03 +0000 (14:38 +0000)]
MIPS: irq: Remove IRQF_DISABLED
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
David Daney [Tue, 22 Nov 2011 14:38:03 +0000 (14:38 +0000)]
MIPS: Handle initmem in systems with kernel not in add_memory_region() mem
This patch addresses a couple of related problems:
1) The kernel may reside in physical memory outside of the ranges set
by plat_mem_setup(). If this is the case, init mem cannot be
reused as it resides outside of the range of pages that the kernel
memory allocators control.
2) initrd images might be loaded in physical memory outside of the
ranges set by plat_mem_setup(). The memory likewise cannot be
reused. The patch doesn't handle this specific case, but the
infrastructure is useful for future patches that do.
The crux of the problem is that there are memory regions that need be
memory_present(), but that cannot be free_bootmem() at the time of
arch_mem_init(). We create a new type of memory (BOOT_MEM_INIT_RAM)
for use with add_memory_region(). Then arch_mem_init() adds the init
mem with this type if the init mem is not already covered by existing
ranges.
When memory is being freed into the bootmem allocator, we skip the
BOOT_MEM_INIT_RAM ranges so they are not clobbered, but we do signal
them as memory_present(). This way when they are later freed, the
necessary memory manager structures have initialized and the Sparse
allocater is prevented from crashing.
The Octeon specific code that handled this case is removed, because
the new general purpose code handles the case.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1988/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hillf Danton [Tue, 22 Nov 2011 14:38:03 +0000 (14:38 +0000)]
MIPS: Add fast get_user_pages
Gup is used in a few cases, say futex.
This work is derived from the x86 version, and operations of pte and pmd are
adapted to the defines of MIPS in straight forward manner.
[ralf@linux-mips.org: Fixed up reject in arch/mips/mm/Makefile due to
whitespace formatting differences. Fixed build error in gup.c due to
conflicting changes elsewhere in the kernel.]
Hillf Danton [Tue, 22 Nov 2011 14:38:02 +0000 (14:38 +0000)]
MIPS: Hugetlb: Keep TLB cache hot while flushing
If we only flush the TLB of the given huge page, the TLB cache remains hot
for the relevant mm as it is, and less will be refilled after flush, huge
or not.
SGI IP22/IP28 machines have GIO busses for adding graphics and other
extension cards. This patch adds support for GIO driver/device
handling and converts the newport console driver to a GIO driver.
[ralf@linux-mips.org: Fixed build error caused by the modules.h -> export.h
changes.]
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
To: linux-fbdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2886/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 22 Nov 2011 14:46:49 +0000 (14:46 +0000)]
MIPS: Oceton: Update model detection code for new chips.
Several newer chips were not covered, update the code to detect them.
This necessitates updating cvmx-mio-defs.h as well, because it has new
and required definitions.
Kevin Cernekee [Fri, 11 Nov 2011 06:30:24 +0000 (22:30 -0800)]
MIPS: BMIPS: Fix up Kconfig settings
Factor out common BMIPS options into "CPU_BMIPS". Add L2 cache for
BMIPS5000. Add CPU_MIPS32 to satisfy checks in page.h, r4k_switch.S,
tlb-r4k.c, etc.
Florian Fainelli [Wed, 16 Nov 2011 18:11:21 +0000 (19:11 +0100)]
MIPS: BCM63xx: Fix GPIO set/get for BCM6345
On BCM6345, the register offsets for the set/get GPIO registers is wrong.
Use the same logic as the one present in arch/mips/bcm63xx/irq.c to
define the correct gpio_out_low_reg value when support for BCM6345
is compiled in.
Florian Fainelli [Wed, 16 Nov 2011 18:11:12 +0000 (19:11 +0100)]
MIPS: BCM63xx: Remove BCM6345 hacks to read base boot address
Though BCM6345 does not technically have the same MPI register layout
than the other SoCs, reading the chip-select registers is done the same
way, and particularly for chip-select 0, which is the boot flash.
Gabor Juhos [Fri, 18 Nov 2011 00:17:54 +0000 (00:17 +0000)]
MIPS: ath79: Rename ATH79_DEV_AR913X_WMAC option to ATH79_DEV_WMAC
The ATH79_DEV_AR913X_WMAC option was used to select the AR913x specific
wireless MAC registration code. The registration code now supports the
AR933X SoCs as well. Rename the option to reflect the changes.
Gabor Juhos [Fri, 18 Nov 2011 00:17:53 +0000 (00:17 +0000)]
MIPS: ath79: Separate AR913x SoC specific WMAC setup code
The device registration code can be shared between the different SoCs, but
the required setup code varies Move AR913x specific setup code into a
separate function in order to make adding support for another SoCs easier.
Gabor Juhos [Fri, 18 Nov 2011 00:17:53 +0000 (00:17 +0000)]
MIPS: ath79: Remove 'ar913x' from common variable and function names
The wireless MAC specific variables and the registration code can be shared
between multiple SoCs. Remove the 'ar913x' part from the function and
variable names to avoid confusions.
Gabor Juhos [Fri, 18 Nov 2011 00:17:46 +0000 (00:17 +0000)]
MIPS: ath79: Store the SoC revision in a global variable
Knowing the exact revision of the SoC is required to make runtime decisions
in various code paths. We have determined the SoC revision already, so we
only need to store that in a global variable.
Gabor Juhos [Mon, 20 Jun 2011 17:26:12 +0000 (19:26 +0200)]
MIPS: ath79: register UART device for the AR933X SoCs
The AR933X SoCs does not have a 8250 compatible UART, they
are using a different UART core. Register a different platform
device for the different UART.
projects / karo-tx-linux.git / log