Peter Hurley [Mon, 16 Jun 2014 13:17:06 +0000 (09:17 -0400)]
tty: Remove tty_hung_up_p() tests from tty drivers' open()
Since at least before 2.6.30, it has not been possible to observe
a hung up file pointer in a tty driver's open() method unless/until
the driver open() releases the tty_lock() (eg., before blocking).
This is because tty_open() adds the file pointer while holding
the tty_lock() _and_ doesn't release the lock until after calling
the tty driver's open() method. [ Before tty_lock(), this was
lock_kernel(). ]
Since __tty_hangup() first waits on the tty_lock() before
enumerating and hanging up the open file pointers, either
__tty_hangup() will wait for the tty_lock() or tty_open() will
not yet have added the file pointer. For example,
Note that since tty_port_block_til_ready() and similar drop
the tty_lock while blocking, when woken, the file pointer
must then be tested for having been hung up.
Also, fix bit-rotted drivers that used extra_count to track the
port->count bump.
CC: Mikael Starvik <starvik@axis.com> CC: Samuel Ortiz <samuel@sortiz.org> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 16 Jun 2014 13:17:03 +0000 (09:17 -0400)]
tty: Move tty->closing from port lock critical section
tty->closing informs the line discipline that the hardware will
be shutting down imminently, and to disable further input other
than soft flow control (but to still allow additional output).
However, the tty lock is the necessary lock for preventing
concurrent changes to tty->closing. As shown by the call-tree
audit [1] of functions that modify tty->closing, the tty lock
is already held for those functions.
[1]
Call-tree audit of functions that modify tty->closing
* does not include call tree to tty_port_close(), tty_port_close_start(),
or tty_port_close_end() which is already documented in
'tty: Document locking for tty_port_close{,start,end}' that shows
callers to those 3 functions hold the tty lock
Peter Hurley [Mon, 16 Jun 2014 13:17:02 +0000 (09:17 -0400)]
tty: Document locking for tty_port_hangup()
The tty lock is held when the tty driver's hangup() method is called
(from the lone call-site, __tty_hangup()). The call-tree audit [1]
of tty_port_hangup() is a closed graph of the callers of
tty_port_hangup(); ie., all callers originate only from __tty_hangup().
Of these callers, none drop the tty lock prior to calling
tty_port_hangup().
Peter Hurley [Mon, 16 Jun 2014 13:17:01 +0000 (09:17 -0400)]
tty: Document locking for tty_port_block_til_ready()
The tty lock is held when the tty driver's open() method is called
(from tty_open()). The call-tree audit [1] of tty_port_block_til_ready()
is a closed graph of the callers of tty_port_block_til_ready();
ie., all callers originate only from tty_open().
Of these callers, none drop the tty lock.
Also, document tty_port_block_til_ready() may drop and reacquire
the tty lock when blocking, which means the tty or tty_port may have
changed state.
[1]
Call-tree audit of tty_port_block_til_ready()
* does not include call tree of tty_port_open() which is already
documented in 'tty: Document locking from tty_port_open()'
Peter Hurley [Mon, 16 Jun 2014 13:17:00 +0000 (09:17 -0400)]
tty: Document locking for tty_port_open()
The tty lock is held when the tty driver's open method is called
(from the lone call-site, tty_open()). The call-tree audit [1] of
tty_port_open() is a closed graph of the callers of tty_port_open();
ie., all callers originate from only tty_open().
Of these callers, none drop the tty lock.
Also, document that tty_port_block_til_ready() may drop and reacquire
the tty lock when blocking, which means the tty or tty_port may have
changed state.
* line_open() is the .open method for 2 um drivers
declared in ./arch/um/drivers/stdio_console.c and
in ./arch/um/drivers/ssl.c, and not called directly
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 16 Jun 2014 13:16:59 +0000 (09:16 -0400)]
tty: Document locking for tty_port_close{,start,end}()
The tty lock is held when the tty driver's .close method is called
(from the two lone call-sites of tty_release() and __tty_hangup()).
The call-tree audit[1] of tty_port_close(), tty_port_close_start,
and tty_port_close_end() is a closed graph of the callers of these
3 functions; ie., all callers originate from only tty_release()
or __tty_hangup().
Of these callers, none drop the tty lock.
Also, document tty_port_close_start() may drop and reacquire the
tty lock in tty_wait_until_sent_from_close(), which means the tty
or tty_port may have changed state (but not reopened or hung up).
[1]
Call-tree audit of tty_port_close, tty_port_close_start, and tty_port_close_end()
* line_close() is the .close method for 2 um drivers,
declared in ./arch/um/drivers/stdio_console.c and
in ./arch/um/drivers/ssl.c, and not called directly
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner [Wed, 2 Jul 2014 16:02:57 +0000 (18:02 +0200)]
serial: fsl_lpuart: calculate DMA burst
The DMA burst size must match the transmit FIFO depth in order
to make sure all character are transmitted. This patch calculates
DMA burst size by using FIFO depth rather than use the hardcoded
16 bytes. This is required since some UARTs (e.g. UART2 on Vybrid)
have a FIFO depth of 8 bytes.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA RX timeout calculation is done based on FIFO buffer size and
port timeout when setting up DMA. However, both variables are not
necessarily initialized at DMA initialization time, which can lead
to a division by zero.
Move the timeout calculation to set_termios where both variables
are initialized.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 9 Jul 2014 13:21:14 +0000 (09:21 -0400)]
serial: core: Preserve termios c_cflag for console resume
When a tty is opened for the serial console, the termios c_cflag
settings are inherited from the console line settings.
However, if the tty is subsequently closed, the termios settings
are lost. This results in a garbled console if the console is later
suspended and resumed.
Preserve the termios c_cflag for the serial console when the tty
is shutdown; this reflects the most recent line settings.
Fixes: Bugzilla #69751, 'serial console does not wake from S3' Reported-by: Valerio Vanni <valerio.vanni@inwind.it> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: tegra: ack the rx dma desc after transfer terminated
The Rx dma descriptor allocated without the DMA_ACK flags so that
once after tarnsfer done or terminated, client can ack the descriptor
to free it for later use.
If the Rx DMA is terminated for some reason then rx-dma descriptor
is not getting acked which causes the memory leak and list of usage
desc to grow continuously.
Hence, acknowledge the rx-dma descriptor once transfer is terminated
to avoid memory leak and desc list to grow.
serial: tegra: update tx_circular buffer only when TX_DMA is in progress
When channel is require to stop transmit then update the Tx circular
buffer only when DMA based transfer is in progress. If there is no
DMA based transfer then no need to update the Tx buffer.
Arnd Bergmann [Thu, 5 Jun 2014 20:54:27 +0000 (22:54 +0200)]
serial: lpc32xx uart module can't do console
Every uart driver that provides a console driver needs to
be built-in for the console code to work, we get a build
error for modular console drivers.
This changes the SERIAL_HS_LPC32XX_CONSOLE symbol to depend
on the SERIAL_HS_LPC32XX driver being built-in, just like
we do for all the other uart drivers.
Arnd Bergmann [Tue, 18 Feb 2014 15:14:20 +0000 (16:14 +0100)]
serial: pxa: fix build with !SERIAL_PXA_CONSOLE
When CONFIG_SERIAL_PXA_CONSOLE is disabled, the serial_pxa_get_poll_char
and serial_pxa_put_poll_char functions are not defined, and we can't
reference them.
Vineet Gupta [Tue, 24 Jun 2014 08:25:07 +0000 (13:55 +0530)]
serial/arc: Refactor by referencing to uart_port where possible
The ARC UART MMIO helpers would take arc_uart_port and then reference
generic uart_port->membase member. So change them to difrectly refer to
uart_port and fix call sites accordingly.
This removes the need for to_arc_port() converion almost eveeywhere and
makes code a bit easier to read.
Andy Shevchenko [Fri, 6 Jun 2014 12:24:10 +0000 (15:24 +0300)]
serial: 8250_dw: use UPF_* constants when define flags
The flags member has upf_t type and corresponding macros to define them. This
patch converts ASYNC_SKIP_TEST to UPF_SKIP_TEST in 8250_dw.c.
Otherwise we got a sparse warning:
drivers/tty/serial/8250/8250_dw.c:302:46: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:62: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:26: warning: incorrect type in assignment (different base types)
drivers/tty/serial/8250/8250_dw.c:302:26: expected restricted upf_t [usertype] flags
drivers/tty/serial/8250/8250_dw.c:302:26: got unsigned int
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 5 Jun 2014 13:51:40 +0000 (16:51 +0300)]
serial: 8250_dw: clock rate handling for all ACPI platforms
This replaces the Baytrail specific custom set_termios hook
with a more generic one where the clock framework is used to
set the rate. The method also doesn't need to be limited to
just Baytrail, so it's used with all ACPI platforms.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Wed, 4 Jun 2014 23:06:41 +0000 (20:06 -0300)]
serial: samsung: Use %pa to print 'resource_size_t' type
When building multi_v7_defconfig with CONFIG_ARM_LPAE=y the following warning
is seen:
drivers/tty/serial/samsung.c: In function 's3c24xx_serial_init_port':
drivers/tty/serial/samsung.c:1229:2: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
Use %pa to print 'resource_size_t' type to fix the warning.
Qipan Li [Thu, 3 Jul 2014 13:26:59 +0000 (21:26 +0800)]
serial: sirf: transfer more bytes once to decrease interrupts
the current codes send 1 bytes, then after getting TX done interrupt,
send subsequent bytes. it causes redundant interrupts.
for example, if we have 3 bytes in TX buffer, the TX flow is:
1. send 1 byte
2. get TX down interrupt
3. send the left 2 bytes
4. get TX down interrupt
this patch moves to send more bytes and decrease interrupts, the new
flow is:
1. send 3 bytes
2. get TX down interrupt
Signed-off-by: Qipan Li <Qipan.Li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomasz Figa [Thu, 26 Jun 2014 11:24:35 +0000 (13:24 +0200)]
ARM: dts: SAMSUNG: Add aliases of UART nodes
This patch adds alias entries for UART nodes of all SoCs using
samsung-uart compatible UART controllers, so that the dependency on
probe order is removed and deterministic device naming is assured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomasz Figa [Thu, 26 Jun 2014 11:24:34 +0000 (13:24 +0200)]
serial: samsung: Consider DT alias when probing ports
Current driver code relies on probe order of particular samsung-uart
instances, which makes it impossible to get proper initialization of
ports when not all ports are available on board, not even saying of
deterministic device naming.
This patch fixes this on DT-enabled systems by using DT aliases for
ports as instance ID, if specified, or falling back to legacy method
otherwise to provide backwards compatibility.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The primary purpose of this patch is to add information about (now
required) aliases of UART ports. However the documentation currently is
heavily outdated and so this patch also takes care of this.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bugfix from Grant Likely:
"Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that
cannot be reached"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, tda998x and vmwgfx fixes,
The main one is i915 fix for missing VGA connectors, along with some
fixes for the tda998x from Russell fixing some modesetting problems.
(still on holidays, but got a spare moment to find these)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
which I introduced in the last round of cleanups :("
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix memory leak when calling irq_free_hwirqs()
irqchip: spear_shirq: Fix interrupt offset
irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
irqchip: armada-370-xp: Mask all interrupts during initialization.
Dave Airlie [Sat, 5 Jul 2014 21:49:59 +0000 (07:49 +1000)]
Merge tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 fixes from Catalin Marinas:
- Exception level check at boot time (for completeness, not triggering
any bug before)
- I/D-cache synchronisation logic for huge pages
- Config symbol typo
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix el2_setup check of CurrentEL
arm64: mm: Make icache synchronisation logic huge page aware
arm64: mm: Fix horrendous config typo
The mach-mxs platform is actually co-maintained by myself and
pengutronix folks. Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Olof Johansson [Sat, 5 Jul 2014 04:51:19 +0000 (21:51 -0700)]
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Maxime Ripard [Sun, 29 Jun 2014 13:48:53 +0000 (15:48 +0200)]
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
This partly reverts commits 553600502b84 (ARM: sunxi: Remove reset code from
the platform) and 5e669ec583e2 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 5 Jul 2014 04:45:38 +0000 (21:45 -0700)]
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Merge tag 'md/3.16-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Two minor bugfixes for md in 3.16"
* tag 'md/3.16-fixes' of git://neil.brown.name/md:
md: flush writes before starting a recovery.
md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status
Merge tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've queued up a few fixes in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix crash when starting transaction
Btrfs: fix btrfs_print_leaf for skinny metadata
Btrfs: fix race of using total_bytes_pinned
btrfs: use E2BIG instead of EIO if compression does not help
btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
Btrfs: fix use-after-free when cloning a trailing file hole
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
btrfs: fix null pointer dereference in clone_fs_devices when name is null
btrfs: fix nossd and ssd_spread mount option regression
Btrfs: fix race between balance recovery and root deletion
Btrfs: atomically set inode->i_flags in btrfs_update_iflags
btrfs: only unlock block in verify_parent_transid if we locked it
Btrfs: assert send doesn't attempt to start transactions
btrfs compression: reuse recently used workspace
Btrfs: fix crash when mounting raid5 btrfs with missing disks
btrfs: create sprout should rename fsid on the sysfs as well
btrfs: dev replace should replace the sysfs entry
btrfs: dev add should add its sysfs entry
btrfs: dev delete should remove sysfs entry
btrfs: rename add_device_membership to btrfs_kobj_add_device
Marc Zyngier [Fri, 6 Jun 2014 13:16:21 +0000 (14:16 +0100)]
arm64: fix el2_setup check of CurrentEL
The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.
It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Steve Capper [Wed, 2 Jul 2014 10:46:23 +0000 (11:46 +0100)]
arm64: mm: Make icache synchronisation logic huge page aware
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org> Tested-by: Mark Brown <broonie@linaro.org> Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> # v3.11+
Mengdong Lin [Thu, 3 Jul 2014 09:02:23 +0000 (17:02 +0800)]
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jani Nikula [Fri, 4 Jul 2014 02:00:37 +0000 (10:00 +0800)]
drm/i915: provide interface for audio driver to query cdclk
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
Merge tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver"
* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: tidspbridge: fix an erroneous removal of parentheses
iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
staging: iio/ad7291: fix error code in ad7291_probe()
iio:adc:ad799x: Fix reading and writing of event values, apply shift
Merge tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows"
* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
kernfs: kernfs_notify() must be useable from non-sleepable contexts
kills the uprobe. Along the way he found some other minor bugs and
clean ups that he fixed up making it a total of 4 patches.
Doing unrelated work, I found that the reading of the ftrace trace
file disables all function tracer callbacks. This was fine when
ftrace was the only user, but now that it's used by perf and kprobes,
this is a bug where reading trace can disable kprobes and perf. A
very unexpected side effect and should be fixed"
* tag 'trace-fixes-v3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove ftrace_stop/start() from reading the trace file
tracing/uprobes: Fix the usage of uprobe_buffer_enable() in probe_event_enable()
tracing/uprobes: Kill the bogus UPROBE_HANDLER_REMOVE code in uprobe_dispatcher()
uprobes: Change unregister/apply to WARN() if uprobe/consumer is gone
tracing/uprobes: Revert "Support mix of ftrace and perf"
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"There is one more fix for the relative paths series from -rc1: Print
the path to the build directory at the start of the build, so that
editors and IDEs can match the relative paths to source files"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Print the name of the build directory
Merge branch 'for-3.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"By coincidence, two NFSv4 symlink bugs, one introduced in the 3.16 xdr
encoding rewrite, the other a decoding bug that I think we've had
since the start but that just doesn't trigger very often"
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
Jan points out that I forgot to make the needed fixes to the
lz4_uncompress_unknownoutputsize() function to mirror the changes done
in lz4_decompress() with regards to potential pointer overflows.
The only in-kernel user of this function is the zram code, which only
takes data from a valid compressed buffer that it made itself, so it's
not a big issue. But due to external kernel modules using this
function, it's better to be safe here.
Reported-by: Jan Beulich <JBeulich@suse.com> Cc: "Don A. Bailey" <donb@securitymouse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[SCSI] use the scsi data buffer length to extract transfer size
Commit 8846bab180fa introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.
However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.
To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.
Reported-by: Christoph Hellwig <hch@infradead.org> Debugged-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Fixes: d77e65350f2d82dfa0557707d505711f5a43c8fd Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
shmem: fix init_page_accessed use to stop !PageLRU bug
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
fs/seq_file: fallback to vmalloc allocation
/proc/stat: convert to single_open_size()
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
msync: fix incorrect fstart calculation
zram: revalidate disk after capacity change
tools: memory-hotplug fix unexpected operator error
tools: cpu-hotplug fix unexpected operator error
autofs4: fix false positive compile error
slub: fix off by one in number of slab tests
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
shmem: fix init_page_accessed use to stop !PageLRU bug
Under shmem swapping load, I sometimes hit the VM_BUG_ON_PAGE(!PageLRU)
in isolate_lru_pages() at mm/vmscan.c:1281!
Commit 2457aec63745 ("mm: non-atomically mark page accessed during page
cache allocation where possible") looks like interrupted work-in-progress.
mm/filemap.c's call to init_page_accessed() is fine, but not mm/shmem.c's
- shmem_write_begin() is clearly wrong to use it after shmem_getpage(),
when the page is always visible in radix_tree, and often already on LRU.
Revert change to shmem_write_begin(), and use init_page_accessed() or
mark_page_accessed() appropriately for SGP_WRITE in shmem_getpage_gfp().
SGP_WRITE also covers shmem_symlink(), which did not mark_page_accessed()
before; but since many other filesystems use [__]page_symlink(), which did
and does mark the page accessed, consider this as rectifying an oversight.
Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Prabhakar Lad <prabhakar.csengg@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 2 Jul 2014 22:22:38 +0000 (15:22 -0700)]
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
Revert commit 939f04bec1a4 ("printk: enable interrupts before calling
console_trylock_for_printk()").
Andreas reported:
: None of the post 3.15 kernel boot for me. They all hang at the GRUB
: screen telling me it loaded and started the kernel, but the kernel
: itself stops before it prints anything (or even replaces the GRUB
: background graphics).
939f04bec1a4 is modest latency reduction. Revert it until we understand
the reason for these failures.
Reported-by: Andreas Bombe <aeb@debian.org> Cc: Jan Kara <jack@suse.cz> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
The test fails in the middle when it is not run as root while accessing
/proc/sys/kernel/msg_next_id. Changed it to check for root at the
beginning of the test and exit if not root.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Davidlohr Bueso <davidlohr@hp.com> Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a couple of seq_files which use the single_open() interface.
This interface requires that the whole output must fit into a single
buffer.
E.g. for /proc/stat allocation failures have been observed because an
order-4 memory allocation failed due to memory fragmentation. In such
situations reading /proc/stat is not possible anymore.
Therefore change the seq_file code to fallback to vmalloc allocations
which will usually result in a couple of order-0 allocations and hence
also work if memory is fragmented.
For reference a call trace where reading from /proc/stat failed:
These two patches are supposed to "fix" failed order-4 memory
allocations which have been observed when reading /proc/stat. The
problem has been observed on s390 as well as on x86.
To address the problem change the seq_file memory allocations to
fallback to use vmalloc, so that allocations also work if memory is
fragmented.
This approach seems to be simpler and less intrusive than changing
/proc/stat to use an interator. Also it "fixes" other users as well,
which use seq_file's single_open() interface.
This patch (of 2):
Use seq_file's single_open_size() to preallocate a buffer that is large
enough to hold the whole output, instead of open coding it. Also
calculate the requested size using the number of online cpus instead of
possible cpus, since the size of the output only depends on the number
of online cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Ian Kent <raven@themaw.net> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Thorsten Diehl <thorsten.diehl@de.ibm.com> Cc: Andrea Righi <andrea@betterlinux.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Stefan Bader <stefan.bader@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
Until now, the kernel has the same policy to handle victimized page
frames that belong to kernel-space(reserved/slab-subsystem) or
non-LRU(unknown page state). In other word, the result of handling
either of these victimized page frames is (IGNORED | FAILED), and the
return value of memory_failure() is -EBUSY.
This patch is to avoid that memory_failure() returns very soon due to
the "true" value of (!PageLRU(p)), and it also ensures that
action_result() can report more precise information("reserved kernel",
"kernel slab", and "unknown page state") instead of "non LRU",
especially for memory errors which are detected by memory-scrubbing.
Andi said:
: While running the mcelog test suite on 3.14 I hit the following VM_BUG_ON:
:
: soft_offline: 0x56d4: unknown non LRU page type 3ffff800008000
: page:ffffea000015b400 count:3 mapcount:2097169 mapping: (null) index:0xffff8800056d7000
: page flags: 0x3ffff800004081(locked|slab|head)
: ------------[ cut here ]------------
: kernel BUG at mm/rmap.c:1495!
:
: I think what happened is that a LRU page turned into a slab page in
: parallel with offlining. memory_failure initially tests for this case,
: but doesn't retest later after the page has been locked.
:
: ...
:
: I ran this patch in a loop over night with some stress plus
: the mcelog test suite running in a loop. I cannot guarantee it hit it,
: but it should have given it a good beating.
:
: The kernel survived with no messages, although the mcelog test suite
: got killed at some point because it couldn't fork anymore. Probably
: some unrelated problem.
:
: So the patch is ok for me for .16.
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
When using trace-vmscan-postprocess.pl for checking the file/anon rate
of scanning, we can find that it can not be performed. At the same
time, the following message will be reported:
WARNING: Format not as expected for event vmscan/mm_vmscan_lru_isolate
'file' != 'contig_taken' Fewer fields than expected in format at
./trace-vmscan-postprocess.pl line 171, <FORMAT> line 76.
In trace-vmscan-postprocess.pl, (contig_taken, contig_dirty, and
contig_failed) are be associated respectively to (nr_lumpy_taken,
nr_lumpy_dirty, and nr_lumpy_failed) for lumpy reclaim. Via commit c53919adc045 ("mm: vmscan: remove lumpy reclaim"), lumpy reclaim had
already been removed by Mel, but the update for
trace-vmscan-postprocess.pl was missed.
Minchan Kim [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
zram: revalidate disk after capacity change
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <minchan@kernel.org> Reported-by: Alexander E. Patrakov <patrakov@gmail.com> Tested-by: Alexander E. Patrakov <patrakov@gmail.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Nitin Gupta <ngupta@vflare.org> Acked-by: Jerome Marchand <jmarchan@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
Ian Kent [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
autofs4: fix false positive compile error
On strict build environments we can see:
fs/autofs4/inode.c: In function 'autofs4_fill_super':
fs/autofs4/inode.c:312: error: 'pgrp' may be used uninitialized in this function
make[2]: *** [fs/autofs4/inode.o] Error 1
make[1]: *** [fs/autofs4] Error 2
make: *** [fs] Error 2
make: *** Waiting for unfinished jobs....
This is due to the use of pgrp_set being used to indicate pgrp has has
been set rather than initializing pgrp itself.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
slub: fix off by one in number of slab tests
min_partial means minimum number of slab cached in node partial list.
So, if nr_partial is less than it, we keep newly empty slab on node
partial list rather than freeing it. But if nr_partial is equal or
greater than it, it means that we have enough partial slabs so should
free newly empty slab. Current implementation missed the equal case so
if we set min_partial is 0, then, at least one slab could be cached.
This is critical problem to kmemcg destroying logic because it doesn't
works properly if some slabs is cached. This patch fixes this problem.
Fixes 91cb69620284 ("slub: make dead memcg caches discard free slabs
immediately").
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = fffffe0000050000
[00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407
Internal error: Oops: 96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
â\80\9cpageblock_order > MAX_ORDERâ\80\9d condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> [3.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filipe Manana [Tue, 24 Jun 2014 16:46:58 +0000 (17:46 +0100)]
Btrfs: fix crash when starting transaction
Often when starting a transaction we commit the currently running transaction,
which can end up writing block group caches when the current process has its
journal_info set to NULL (and not to a transaction). This makes our assertion
at btrfs_check_data_free_space() (current_journal != NULL) fail, resulting
in a crash/hang. Therefore fix it by setting journal_info.
Liu Bo [Wed, 2 Jul 2014 08:58:01 +0000 (16:58 +0800)]
Btrfs: fix race of using total_bytes_pinned
This percpu counter @total_bytes_pinned is introduced to skip unnecessary
operations of 'commit transaction', it accounts for those space we may free
but are stuck in delayed refs.
And we zero out @space_info->total_bytes_pinned every transaction period so
we have a better idea of how much space we'll actually free up by committing
this transaction. However, we do the 'zero out' part a little earlier, before
we actually unpin space, so we end up returning ENOSPC when we actually have
free space that's just unpinned from committing transaction.
xfstests/generic/074 complained then.
This fixes it by actually accounting the percpu pinned number when 'unpin',
and since it's protected by space_info->lock, the race is gone now.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
David Sterba [Fri, 20 Jun 2014 09:43:20 +0000 (11:43 +0200)]
btrfs: use E2BIG instead of EIO if compression does not help
Return codes got updated in 60e1975acb48fc3d74a3422b21dde74c977ac3d5
(btrfs: return errno instead of -1 from compression)
lzo wrapper returns E2BIG in this case, do the same for zlib.
projects / linux-beck.git / log