Sujith Manoharan [Sat, 23 Aug 2014 13:42:14 +0000 (19:12 +0530)]
ath9k: Remove redundant ifdef
This was introduced in an earlier patch to handle
a compilation warning, but since the channel context
code has been mostly isolated, this is not required now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sat, 23 Aug 2014 07:59:23 +0000 (13:29 +0530)]
ath9k: Fix 'offchannel' in ath_softc
Finally move the 'offchannel' instance in ath_softc
inside a CONFIG_ATH9K_CHANNEL_CONTEXT cage. The offchannel
usage in ath9k_calculate_iter_data() is closed off with
an ifdef for now, since the state/opmode calculation is
common for both the channel context mode and the normal mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sat, 23 Aug 2014 07:59:22 +0000 (13:29 +0530)]
ath9k: Fix function argument type
ath9k_vif_iter() was earlier used as an iterator
routine when calling a mac80211 utility. This is no
longer the case and hence we can mention the argument
type explicitly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sat, 23 Aug 2014 07:59:16 +0000 (13:29 +0530)]
ath9k: Fix channel context events
Check if channel context usage is enabled before
calling ath_chanctx_event() from various parts of the
driver. Also, make sure that ath_chanctx_event() is
compiled only when CONFIG_ATH9K_CHANNEL_CONTEXT is
enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The carl9170_op_ampdu_action() function is used only by the mac80211
framework.
Since the mac80211 already takes care of checks and properly serializing
calls to the driver's function there is no need for the driver to do the same
thing.
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 22 Aug 2014 15:09:31 +0000 (20:39 +0530)]
ath9k: Isolate ath9k_use_chanctx module parameter
This patch ensures that the module parameter "use_chanctx" is
visible only when CONFIG_ATH9K_CHANNEL_CONTEXT is selected.
Also register the channel context callbacks with mac80211 only
when it is explicitly enabled and compile them out of the driver
when CONFIG_ATH9K_CHANNEL_CONTEXT is not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 22 Aug 2014 15:09:28 +0000 (20:39 +0530)]
ath9k: Add a config option for channel context
Channel contexts are supported only for P2P right now,
so make sure that the 'normal' path remains unaffected
by using a config option. This will also reduce the size
of the driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Fri, 22 Aug 2014 13:18:01 +0000 (09:18 -0400)]
ath5k: ensure led name is null terminated
Add the missing null termination after strncpy().
This isn't actually a buffer overflow in this case since we use
snprintf() appropriately to fill the buffer passed by the caller,
but in the interest of not turning this into a bug down the road,
go ahead and force termination here.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rasmus Villemoes [Mon, 25 Aug 2014 07:59:29 +0000 (09:59 +0200)]
ray_cs: Add include guards
The files ray_cs.h and rayctl.h both contain two thirds of what
appears to be an include guard using the macro name RAYLINK_H (both
lack the #define). Since RAYLINK_H is not defined anywhere, the
#ifndefs are confusing no-ops. Add proper include guards using
different macro names.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 19 Aug 2014 12:24:26 +0000 (08:24 -0400)]
mwifiex: use firmware API revision from GET_HW_SPEC response
Newer firmware returns API revision in GET_HW_SPEC command
response. We will make use of it instead of parsing this
information from FW release number.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 19 Aug 2014 12:24:24 +0000 (08:24 -0400)]
mwifiex: fix left_len calculation issue
While updating 'left_len' in each iteration, we should subtract
last TLV length not the accumulated length of TLVs parsed till
now.
This bug in parsing logic is exposed by newer firmware which adds
two TLVs in GET_HW_SPEC command response. Earlier firmwares used to
add only one TLV.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Csaba Kiraly [Sun, 17 Aug 2014 23:53:34 +0000 (01:53 +0200)]
ath9k_htc: advertise support for TDLS
Based on a quick test with AR9271, TDLS seems to be working fine.
Tests were done with 2 Atheros AR9271 based devices with firmware
1.3 (sha1 8d49f928aa40ac53c729189bff1333cd373a7fb5), associated
with a WAP54G access point. TDLS worked fine both in WPA2 mode and
without encryption. Stations maintained ping flood traffic between
each other and towards the AP without significant losses.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Himangi Saraogi [Wed, 13 Aug 2014 17:10:24 +0000 (22:40 +0530)]
atmel_cs: Remove typedef local_info_t
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently it can send regulatory domain change notification before any
NEW_WIPHY notification. Moreover, if rfill_register() fails, calling
wiphy_unregister() will send a DEL_WIPHY though no NEW_WIPHY had been
sent previously.
Thus reordering so it properly notifies NEW_WIPHY before any other.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Himangi Saraogi [Thu, 7 Aug 2014 11:02:45 +0000 (16:32 +0530)]
wireless: wlcore: Use devm_kzalloc
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a couple of labels and
the initial assignment of the ret variable in the probe function are
removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define tables for similar file entries, i.e.
- table for debugfs_create_file
- table for static parameters
- table for parameters that are members of "wil" structure
- table for blobs
- table for interrupt controllers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wil6210: wait longer for hardware reset completion
Typical time for hardware reset, as measured, is about 200..250 msec.
Adjust sleeping to use more relaxed msleep, increase sleep interval
and increase total sleep time to be about 1sec
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When resetting target in wil_target_reset(), error may occur.
Indicate error via error code. In case of error, don't attempt to further
interact with card, specifically don't attempt firmware download or
interrupts enabling.
Move wil_rx_fini() to be always executed to prevent memory leak.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Himangi Saraogi [Sat, 2 Aug 2014 14:52:46 +0000 (20:22 +0530)]
cw1200: Introduce the use of devm_kzalloc
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43: implement PPR (Power Per Rate) management/API
Broadcom hardware supports auto-adjustment of TX power depending on the
currently used rate. So far all calculations were handled without any
helpers (API) using big arrays and magic offsets.
It seems Broadcom recently decided to clean this up by developing PPR.
Their wlc_ppr.h can be found in open parts of the SDK.
As we plan to implement support for rate-based TX power it makes sense
to also implement our version of PPR as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Thu, 7 Aug 2014 05:45:37 +0000 (07:45 +0200)]
b43: flush some writes on Broadcom MIPS SoCs
Access to PHY and radio registers is indirect on Broadcom hardware and
it seems that addressing on some MIPS SoCs may require flushing. So far
this problem was noticed on 0x4716 SoC only (marketing names: BCM4717,
BCM4718).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the PHYs use the same way of accessing registers, so move that
code to the shared place. An exception is G-PHY which sometimes access
A-PHY regs and requires special handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Kazior [Fri, 22 Aug 2014 12:33:18 +0000 (14:33 +0200)]
ath10k: flush hif buffers before recovery
Transport buffers weren't flushed and processed
before queueing hw recovery request to mac80211.
This could in theory result in an unwanted htt/wmi
rx events being processed while mac80211 recovers
the device and possibly interfere or even crash
the system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:33:14 +0000 (14:33 +0200)]
ath10k: rework posting pci rx buffers
It was possible on a host system running low on
memory to end up with no rx buffers on pci pipes.
This makes the driver more robust as it won't fail
to start if it can't allocate all rx buffers right
away. If it is fatal then upper layers will notice
trouble anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:34 +0000 (14:23 +0200)]
ath10k: remove early irq handling
It's not really necessary to have a dedicated irq
handler just for the sake of catching early fw
crashes anymore. It is now safe to use one handler
even during early stages of device boot up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:33 +0000 (14:23 +0200)]
ath10k: make sure to really disable irqs
This fixes two corner cases.
One is a race between disabling copy engine
interrupts and unhandled pending interrupts on the
host. This could end up with a runaway tasklet and
consequently memory leak of a few copy engine
rx buffers.
The other one is an unexpected (and non-maskable
via device CSR) MSI fw indication interrupt during
teardown. This could trigger the same problem as
the first corner case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Fri, 22 Aug 2014 12:23:32 +0000 (14:23 +0200)]
ath10k: split ce irq/handler setup
It doesn't make much sense to overwrite send_cb
and recv_cb callbacks over and over again whenever
transport starts. Just make sure to unmask copy
engine interrupts when starting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Mon, 25 Aug 2014 05:37:32 +0000 (08:37 +0300)]
ath10k: provide firmware crash info via debugfs
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Tue, 19 Aug 2014 11:22:32 +0000 (13:22 +0200)]
ath10k: fix a conflict bug in wmi service bitmap
Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa. This caused wmi_services in debugfs to print wrong values.
This fixes commit cff990ce7ddd6 ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
"Here are some bug fixes that have piled up during ksummit/linuxcon.
1) Fix endian problems in ibmveth, from Anton Blanchard.
2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
Benjamin Block.
3) SCTP association fixes from Daniel Borkmann.
4) When multiple VLAN headers are present we have to make sure the
second and subsequent ones are pullable in the SKB otherwise we
blindly dereference garbage. From Jiri Benc.
5) The argument adjustment of the signature of hlist_add_after*()
introduced a regression in the batman-adv code, fix from Sven
Eckelmann.
6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
Jain.
7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.
8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
Chas Williams.
9) Truncate packets larger then the TPACKET_V3 format configured
buffers, otherwise we overwrite past the end of said buffers.
From Eric Dumazet.
10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
Borundia and Shahed Shaikh.
11) CXGB4 sometimes doesn't get all of the TX completion events it
should resulting in SKBs getting stuck in the TX queue, from
Hariprasad Shenai.
12) When the FEC chip's PTP clock is disabled, you can't access the
register. Add necessary checks to avoid the resulting hang, from
Fugang Duan"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
ibmveth: Fix endian issues with rx_no_buffer statistic
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
openvswitch: fix panic with multiple vlan headers
net: ipv6: fib: don't sleep inside atomic lock
net: fec: ptp: avoid register access when ipg clock is disabled
cxgb4: Free completed tx skbs promptly
cxgb4: Fix race condition in cleanup
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
bnx2x: Revert UNDI flushing mechanism
qlcnic: Fix endianess issue in firmware load from file operation
qlcnic: Fix endianess issue in FW dump template header
qlcnic: Fix flash access interface to application
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
macvlan: Allow setting multicast filter on all macvlan types
packet: handle too big packets for PACKET_V3
MAINTAINERS: add entry for ec_bhf driver
...
Daniel Borkmann [Fri, 22 Aug 2014 11:03:30 +0000 (13:03 +0200)]
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().
Commits 4c47af4d5eb2 ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4dd509 ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.
Currently, the selection algorithm for T.ACT and T.RET is as follows:
1) Elect the two most recently used ACTIVE transports T1, T2 for
T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI
Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:
T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.
After the patch, it's choosing better transports in both cases by
modifying step 4):
4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
the most recently used (if avail) in PF, set T.RET<-T.ACT_new
This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.
In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.
Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.
In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 22 Aug 2014 11:03:29 +0000 (13:03 +0200)]
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Fri, 22 Aug 2014 01:36:52 +0000 (11:36 +1000)]
ibmveth: Fix endian issues with rx_no_buffer statistic
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.
And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Thu, 21 Aug 2014 19:33:44 +0000 (21:33 +0200)]
openvswitch: fix panic with multiple vlan headers
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log