Manuel Lauss [Sun, 4 Oct 2009 12:55:26 +0000 (14:55 +0200)]
MIPS: Alchemy: remove board_init_irq() function.
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 4 Oct 2009 12:55:24 +0000 (14:55 +0200)]
MIPS: Alchemy: devboard register abstraction
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christian Kujau [Fri, 26 Feb 2010 17:25:14 +0000 (17:25 +0000)]
Remove EXPERIMENTAL from NFS_FSCACHE
There's currently an open Ubuntu bug[0], with the intent to compile NFS_FSCACHE
(and possibly AFS_FSCACHE, 9P_FSCACHE) into the standard Ubuntu kernel.
However, since *_FSCACHE still depends on EXPERIMENTAL, this won't happen.
As Arjan van de Ven pointed out[1], the EXPERIMENTAL flag doesn't mean that
much any more, I propose the following patch to fs/nfs/Kconfig. I'd do the
same for fs/9p/Kconfig and fs/afs/Kconfig, but as I did not test 9p or AFS, I
feel it would not be appropriate for me to remove the flag.
Linus Torvalds [Sat, 27 Feb 2010 01:20:18 +0000 (17:20 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
Linus Torvalds [Sat, 27 Feb 2010 01:19:30 +0000 (17:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use bastmode in debugfs output
dlm: Send lockspace name with uevents
dlm: send reply before bast
dlm: fix ordering of bast and cast
Linus Torvalds [Sat, 27 Feb 2010 01:18:52 +0000 (17:18 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (52 commits)
fs/xfs: Correct NULL test
xfs: optimize log flushing in xfs_fsync
xfs: only clear the suid bit once in xfs_write
xfs: kill xfs_bawrite
xfs: log changed inodes instead of writing them synchronously
xfs: remove invalid barrier optimization from xfs_fsync
xfs: kill the unused XFS_QMOPT_* flush flags V2
xfs: Use delay write promotion for dquot flushing
xfs: Sort delayed write buffers before dispatch
xfs: Don't issue buffer IO direct from AIL push V2
xfs: Use delayed write for inodes rather than async V2
xfs: Make inode reclaim states explicit
xfs: more reserved blocks fixups
xfs: turn off sign warnings
xfs: don't hold onto reserved blocks on remount,ro
xfs: quota limit statvfs available blocks
xfs: replace KM_LARGE with explicit vmalloc use
xfs: cleanup up xfs_log_force calling conventions
xfs: kill XLOG_VEC_SET_TYPE
xfs: remove duplicate buffer flags
...
Linus Torvalds [Sat, 27 Feb 2010 01:16:20 +0000 (17:16 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
Ang Way Chuang [Thu, 25 Feb 2010 01:45:03 +0000 (09:45 +0800)]
dvb-core: Fix DoS bug in ULE decapsulation code that can be triggered by an invalid Payload Pointer
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 27 Feb 2010 01:11:11 +0000 (17:11 -0800)]
Merge branch 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
kmemcheck: Test the full object in kmemcheck_is_obj_initialized()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/xfs-vipt:
xfs: fix xfs to work with Virtually Indexed architectures
sh: add mm API for DMA to vmalloc/vmap areas
arm: add mm API for DMA to vmalloc/vmap areas
parisc: add mm API for DMA to vmalloc/vmap areas
mm: add coherence API for DMA to vmalloc/vmap areas
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
Joe Perches [Thu, 14 Jan 2010 16:34:19 +0000 (11:34 -0500)]
drivers/firmware/iscsi_ibft.c: remove NIPQUAD_FMT, use %pI4
Convert netmask to __be32 and format it with %pI4
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Cc: Peter Jones <pjones@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com> Cc: stable@kernel.org
Jiri Slaby [Sun, 21 Feb 2010 21:14:44 +0000 (22:14 +0100)]
PM / Hibernate: Remove swsusp.c finally
Its contents and entry in Makefile were already removed in 8e60c6a1348e17e68ad73589a52a03876e7059be
(Shift remaining code from swsusp.c to hibernate.c)
but somehow it remained in-place (rjw: which most likely was my
mistake).
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Nigel Cunningham <nigel@tuxonice.net> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM: Allow SCSI devices to suspend/resume asynchronously
Set power.async_suspend for all SCSI devices, targets and hosts, so
that they can be suspended and resumed in parallel with the main
suspend/resume thread and possibly with other devices they don't
depend on in a known way (i.e. devices which are not their parents or
children).
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
PM: Allow USB devices to suspend/resume asynchronously
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Alan Stern [Fri, 12 Feb 2010 11:21:11 +0000 (12:21 +0100)]
USB: implement non-tree resume ordering constraints for PCI host controllers
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM: Allow PCI devices to suspend/resume asynchronously
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Jiri Slaby [Wed, 27 Jan 2010 22:47:56 +0000 (23:47 +0100)]
PM / Hibernate: Swap, remove useless check from swsusp_read()
It will never reach here if the sws_resume_bdev is erratic.
swsusp_read() is called only from software_resume(), but after
swsusp_check() which would catch the error state.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are some dependencies between devices (in particular, between
EHCI USB controllers and their OHCI/UHCI siblings) which are not
reflected by the structure of the device tree. With synchronous
suspend and resume these dependencies are taken into accout
automatically, because the devices in question are always registered
in the right order, but to meet these constraints with asynchronous
suspend and resume the drivers of these devices will need to use
dpm_wait() in their suspend/resume routines, so introduce a helper
function allowing them to do that.
It has been shown by testing that total device resume time can be
reduced significantly (by as much as 50% or more) if the async
threads executing some devices' resume routines are all started
before the main resume thread starts to handle the "synchronous"
devices.
This is a consequence of the fact that the slowest devices tend to be
located at the end of dpm_list, so their resume routines are started
very late. Consequently, they have to wait for all the preceding
"synchronous" devices before their resume routines can be started
by the main resume thread, even if they are "asynchronous". By
starting their async threads upfront we effectively move those
devices towards the beginning of dpm_list, without breaking their
ordering with respect to their parents and children. As a result,
their resume routines are started much earlier and we are able to
save much more device resume time this way.
PM: Add facility for advanced testing of async suspend/resume
Add configuration switch CONFIG_PM_ADVANCED_DEBUG for compiling in
extra PM debugging/testing code allowing one to access some
PM-related attributes of devices from the user space via sysfs.
If CONFIG_PM_ADVANCED_DEBUG is set, add sysfs attribute power/async
for every device allowing the user space to access the device's
power.async_suspend flag and modify it, if desired.
Theoretically, the total time of system sleep transitions (suspend
to RAM, hibernation) can be reduced by running suspend and resume
callbacks of device drivers in parallel with each other. However,
there are dependencies between devices such that we're not allowed
to suspend the parent of a device before suspending the device
itself. Analogously, we're not allowed to resume a device before
resuming its parent.
The most straightforward way to take these dependencies into accout
is to start the async threads used for suspending and resuming
devices at the core level, so that async_schedule() is called for
each suspend and resume callback supposed to be executed
asynchronously.
For this purpose, introduce a new device flag, power.async_suspend,
used to mark the devices whose suspend and resume callbacks are to be
executed asynchronously (ie. in parallel with the main suspend/resume
thread and possibly in parallel with each other) and helper function
device_enable_async_suspend() allowing one to set power.async_suspend
for given device (power.async_suspend is unset by default for all
devices). For each device with the power.async_suspend flag set the
PM core will use async_schedule() to execute its suspend and resume
callbacks.
The async threads started for different devices as a result of
calling async_schedule() are synchronized with each other and with
the main suspend/resume thread with the help of completions, in the
following way:
(1) There is a completion, power.completion, for each device object.
(2) Each device's completion is reset before calling async_schedule()
for the device or, in the case of devices with the
power.async_suspend flags unset, before executing the device's
suspend and resume callbacks.
(3) During suspend, right before running the bus type, device type
and device class suspend callbacks for the device, the PM core
waits for the completions of all the device's children to be
completed.
(4) During resume, right before running the bus type, device type and
device class resume callbacks for the device, the PM core waits
for the completion of the device's parent to be completed.
(5) The PM core completes power.completion for each device right
after the bus type, device type and device class suspend (or
resume) callbacks executed for the device have returned.
Add new device sysfs attribute, power/control, allowing the user
space to block the run-time power management of the devices. If this
attribute is set to "on", the driver of the device won't be able to power
manage it at run time (without breaking the rules) and the device will
always be in the full power state (except when the entire system goes
into a sleep state).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu>
V4L-DVB: cx88-dvb: remove extra attribution for core
This is not needed, since the function already do it. Also, it causes
a warning at the compilation, since a new var is declared in the middle
of the code.
Linus Torvalds [Fri, 26 Feb 2010 18:35:27 +0000 (10:35 -0800)]
Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
David Teigland [Thu, 25 Feb 2010 18:20:57 +0000 (12:20 -0600)]
dlm: use bastmode in debugfs output
The bast mode that appears in the debugfs output should be
useful on both master and process nodes. lkb_highbast is
currently printed, and is only useful on the master node.
lkb_bastmode is only useful on the process node. This
patch sets lkb_bastmode on the master node as well, and
uses that value in the debugfs print.
Signed-off-by: David Teigland <teigland@redhat.com>
Hans de Goede [Fri, 19 Feb 2010 07:41:40 +0000 (04:41 -0300)]
V4L/DVB: gspca_main: some input error handling fixes
2 small changes to input device error handling:
1) Make it fatal when we fail to create an input device (it is either this
or add checks for gspca_dev->input_dev being NULL in a lot of places)
2) Since we allow gspca_input_create_urb() to fail everywhere we call it,
and thus never check its return value, make it void.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 17 Feb 2010 14:59:19 +0000 (11:59 -0300)]
V4L/DVB: gspca_pac7302: much improved exposure control
My experience with fixing up the controls for the PAS sensors in
sonixb, has lead me to re-investigate the exposure control for the
pac7302. I've now found a regular exposure register in register bank 3
(which seems to be the sensor registers bank), and with this added a proper
fine grained exposure control. This patch also updates the do_autogain
function to work properly with this new finer grained control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 10 Feb 2010 21:57:40 +0000 (18:57 -0300)]
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
Fixup brightness ctrl and add gain and exposure ctrls for PAS106B sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 4 Feb 2010 09:10:55 +0000 (06:10 -0300)]
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
In 640x480, if the reg11 has less than 4, the image is
unstable (the bridge goes into a higher compression mode
which we have not reverse engineered yet).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Feb 2010 17:37:30 +0000 (14:37 -0300)]
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
Fixup brightness ctrl and add gain and exposure ctrls for PAS202BCB sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Mon, 1 Feb 2010 16:18:37 +0000 (13:18 -0300)]
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
Some sensors only allow controlling the exposure by changing the clockdiv,
which means that exposure takes pretty large jumps (for example when going
from a div of 1 to 2, the exposure doubles). Use 2 different entries in
the controls array for these 2 different types of exposure (always
disabling one), and;
Add a new autogain algorithm for the coarse exposure case, which normally
changes the gain setting, only touching the exposure setting if the desired
luminance cannot be reached with gain, and after an exposure change once more
first tries gain, etc. Thus avoiding exposure changes, and the resulting
oscilation because of the huge steps these exposure controls take.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Mon, 1 Feb 2010 10:48:17 +0000 (07:48 -0300)]
V4L/DVB: gspca_sonixb: leave bridge gain at 1.0 when we have a sensor gain
Leave bridge gain at 1.0 when we have a sensor gain, while at it also
change the bridge gain setting code to write both registers in one go
saving us a usb transaction.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eric Anderson [Thu, 11 Feb 2010 01:14:54 +0000 (22:14 -0300)]
V4L/DVB: ivtv: Add initial entry for Sony VAIO Giga Pocket (Kikyou) cards
This is a slightly modified version of Eric Anderson's original patch
for the Sony Giga Pocket board. It has been updated to apply to the
latest ivtv driver version by Hans Verkuil <hverkuil@xs4all.nl> and
Andy Walls <awalls@radix.net>. Also Andy Walls modified the patch to
use a new Sony BTF-Pnx01Z tuner entry based on Eric Anderson's experimental
findings for the bandswitch.
>From Eric Anderson's original email:
1. The tuner on the card doesn't seem to match any standard
ones. I modified an existing tuner entry. Ideally a new tuner
entry should be created. (The only difference from the one I
modified is that the low-to-mid range frequency cut-off is
slightly different, as are the bit config settings.)
2. It wasn't obvious how to choose a second audio input other
than using "radio" as an option. Basically there's two GPIO
audio inputs. Using radio allowed me to avoid major restructuring
to the code. (perhaps other cards don't have this often...)
3. It's not clear that there's a mute setting that works. Not
sure why.
4. I haven't had a chance to test the two Svideo inputs. I set
them to COMPOSITE1 and SVIDEO2, but I'm not sure those are the
correct settings. The standard composite video inputs seem to work.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 10 Feb 2010 22:02:58 +0000 (19:02 -0300)]
V4L/DVB: tuner-types: Add Sony BTF-Pxn01Z tuner type used on GigaPocket cards
Sony makes custome tuners for its GigaPocket line of ivtv based capture
cards. This adds an entry to the tuner-types list for such tuners.
Parameters are based on experiments by Eric Anderson <rico99@sbcglobal.net>.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 10 Feb 2010 18:34:46 +0000 (15:34 -0300)]
V4L/DVB: ivtv: Fix ivtv_api_get_data() to avoid unneeded IO during IRQ handling
ivtv_api_get_data() was performing more PCI MMIO than needed, resulting
often in it accounting for more than half the total time spent in
ivtv_irq_handler(). Now it only reads at most 7 of the 16 mailbox data words
over the PCI bus, and in some instances only 2 or 3 data words as needed.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Murali Karicheri [Sun, 21 Feb 2010 18:48:27 +0000 (15:48 -0300)]
V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365
This is the source file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for YUV capture from
TVP514x driver. This patch contains the header files required for this driver.
This is the header file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for
YUV capture from TVP514x driver. This patch contains the header files required
for this driver.
V4L/DVB: DaVinci - Adding platform & board changes for vpfe capture on DM365
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Murali Karicheri <mkaricheri@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 6 Feb 2010 05:17:17 +0000 (02:17 -0300)]
V4L/DVB: pvrusb2: Adjust 300msec digitizer wait to be more selective
We know that the 300msec settling time after starting the digitizer is
only really needed when the digitizer is a SAA7115. So if we're not
using a SAA7115, skip the delay.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 6 Feb 2010 05:12:33 +0000 (02:12 -0300)]
V4L/DVB: pvrusb2: Reduce encoder quiet period
After implementing a 300msec wait between digitizer start and encoder
start, it has been determined that we don't need to wait quite as long
before configuring the encoder. This reduces the wait period from
100msec back to 50msec.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 6 Feb 2010 05:10:38 +0000 (02:10 -0300)]
V4L/DVB: pvrusb2: Enforce a 300msec stabilization interval during stream strart
Martin Dauskardt <martin.dauskardt@gmx.de> has determined that the
encoder has a much better chance of starting cleanly if we
deliberately hold off starting it util the video digitizer has had a
chance to run for at least 300msec first. These changes implement an
enforced 300msec wait in the state machine that orchestrates streaming
start / stop.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Mon, 22 Feb 2010 20:47:46 +0000 (17:47 -0300)]
V4L/DVB: V4L2: Add a document describing the videobuf layer
Videobuf is a moderately complex API which most V4L2 drivers should use,
but its documentation is...sparse. This document attempts to improve the
situation.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Reviewed-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media spec contains several errors in the description of the
I/O streaming ioctls, in particular with respect to the userptr
I/O method.
The most important change is that you really need to set count
and index in v4l2_requestbuffer and v4l2_buffer when dealing with
user pointer streaming.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 20 Feb 2010 11:07:51 +0000 (08:07 -0300)]
V4L/DVB: saa7115: fix saa7111a support
When the saa7111 driver was merged into saa7115 several bugs were introduced,
in particular with the saa7111a support as is used in the mxb.c driver.
This patch fixes the saa7111a support. This was tested with the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 20 Feb 2010 10:56:25 +0000 (07:56 -0300)]
V4L/DVB: saa7146_vv: fix regression where v4l2_device was registered too late
v4l2_device_register needs to be called before the i2c subdevs are loaded.
However, it was called afterwards in the saa7146 driver. This caused an oops
when loading the mxb and hexium drivers. The vv_init function is now split
into two: one registers the v4l2_device, the other does the rest of the
initialization. The three drivers that depend on this have been updated to
call the new vv_devinit function.
Thanks to Michael Hunold for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: uvcvideo: Blacklist gain control for Asus EeePC T91 integrated webcam
The Asus EeePC T91 integrated webcam exposes a gain control in the
processing unit but stalls when the control is queried. Blacklist the
gain control for that camera.
Laurent Pinchart [Sat, 23 Jan 2010 10:07:53 +0000 (07:07 -0300)]
V4L/DVB: uvcvideo: Clamp control values to the minimum and maximum values
When setting a control, the V4L2 specification requires drivers to
either clamp the control value to the [minimum, maximum] range or return
the -ERANGE error.
Fix the driver to clamp control values to the valid range in
uvc_ctrl_set() and make sure the value differs from the minimum by an
integer multiple of step.
Laurent Pinchart [Tue, 19 Jan 2010 11:59:21 +0000 (08:59 -0300)]
V4L/DVB: uvcvideo: Increase the streaming control timeout to 5 seconds
This fixes timeout issues with some Logitech webcams. The timeout value
seems to match the one used in the Logitech Windows driver, so no
further increase should be necessary.
Ensure that volume values are always in the allowed range. Otherwise,
it would be possible to set other bits in the AUD_VOL_CTL register or to
get a wrong sign in the AUD_BAL_CTL register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mv-sheeva.git / log